Abstract: Fibre cement plates, often used in construction,
generally are made using quartz as an inert material, cement as a
binder and cellulose as a fibre. This paper, first of all, investigates the
mechanical properties and durability of fibre cement plates when
quartz is both partly and fully replaced with diatomite. Diatomite
does not only have lower density compared to quartz but also has
high pozzolanic activity. The main objective of this paper is the
investigation of the effects of supplementary cementing materials
(SCMs) on the short and long term mechanical properties and
durability characteristics of fibre cement plates prepared using
diatomite. Supplementary cementing materials such as ground
granulated blast furnace slug (GGBS) and fly ash (FA) are used in
this study. Volume proportions of 10, 20, 30 and 40% of GGBS and
FA are used as partial replacement materials to cement. Short and
long term mechanical properties such as compressive and flexural
strengths as well as sorptivity characteristics and mass were
investigated. Consistency and setting time at each replacement levels
of SCMs were also recorded. The effects of using supplementary
cementing materials on the carbonation and sulphate resistance of
fibre cement plates were then experimented. The results, first of all,
show that the use of diatomite as a full or partial replacement to
quartz resulted in a systematic decrease in total mass of the fibre
cement plates. The reduction of mass was largely due to the lower
density and finer particle size of diatomite compared to quartz. The
use of diatomite did not only reduce the mass of these plates but also
increased the compressive strength significantly as a result of its high
pozzolanic activity. The replacement levels of both GGBS and FA
resulted in a systematic decrease in short term compressive strength
with increasing replacement levels. This was essentially expected as
the total rate of hydration is much lower in GGBS and FA than that
of cement. Long term results however, indicated that the compressive
strength of fibre cement plates prepared using both GGBS and FA
increases with time and hence the compressive strength of plates
prepared using SCMs is either equivalent or more than the
compressive strength of plates prepared using cement alone.
Durability characteristics of fibre cement plates prepared using SCMs
were enhanced significantly. Measurements of sopritivty
characteristics were also indicated that the plates prepared using
SCMs has much lower water absorption capacities compared to
plates prepared cement alone. Much higher resistance to carbonation
and sulphate attach were observed with plates prepared using SCMs.
The results presented in this paper show that the use of SCMs does
not only support the production of more sustainable construction
materials but also enhances the mechanical properties and durability
characteristics of fibre cement plates.
Abstract: This study, for its research subjects, uses patients who
had undergone total knee replacement surgery from the database of the
National Health Insurance Administration. Through the review of
literatures and the interviews with physicians, important factors are
selected after careful screening. Then using Cross Entropy Method,
Genetic Algorithm Logistic Regression, and Particle Swarm
Optimization, the weight of each factor is calculated and obtained. In
the meantime, Excel VBA and Case Based Reasoning are combined
and adopted to evaluate the system. Results show no significant
difference found through Genetic Algorithm Logistic Regression and
Particle Swarm Optimization with over 97% accuracy in both
methods. Both ROC areas are above 0.87. This study can provide
critical reference to medical personnel as clinical assessment to
effectively enhance medical care quality and efficiency, prevent
unnecessary waste, and provide practical advantages to resource
allocation to medical institutes.
Abstract: In recent years a new method of combination
treatment for cancer has been developed and studied that has led to
significant advancements in the field of cancer therapy. Hyperthermia
is a traditional therapy that, along with a creation of a medically
approved level of heat with the help of an alternating magnetic AC
current, results in the destruction of cancer cells by heat. This paper
gives details regarding the production of the spherical nanocomposite
PVA/γ-Fe2O3 in order to be used for medical purposes such as tumor
treatment by hyperthermia. To reach a suitable and evenly distributed
temperature, the nanocomposite with core-shell morphology and
spherical form within a 100 to 200 nanometer size was created using
phase separation emulsion, in which the magnetic nano-particles γ-
Fe2O3 with an average particle size of 20 nano-meters and with
different percentages of 0.2, 0.4, 0.5 and 0.6 were covered by
polyvinyl alcohol. The main concern in hyperthermia and heat
treatment is achieving desirable specific absorption rate (SAR) and
one of the most critical factors in SAR is particle size. In this project
all attempts has been done to reach minimal size and consequently
maximum SAR. The morphological analysis of the spherical
structure of the nanocomposite PVA/γ-Fe2O3 was achieved by SEM
analyses and the study of the chemical bonds created was made
possible by FTIR analysis. To investigate the manner of magnetic
nanocomposite particle size distribution a DLS experiment was
conducted. Moreover, to determine the magnetic behavior of the γ-
Fe2O3 particle and the nanocomposite PVA/γ-Fe2O3 in different
concentrations a VSM test was conducted. To sum up, creating
magnetic nanocomposites with a spherical morphology that would be
employed for drug loading opens doors to new approaches in
developing nanocomposites that provide efficient heat and a
controlled release of drug simultaneously inside the magnetic field,
which are among their positive characteristics that could significantly
improve the recovery process in patients.
Abstract: The degradation of concrete due to various hygrochemo-
mechanical actions is inevitable for the structures particularly
built to store water. Therefore, it is essential to determine the material
properties of dam-like structures due to ageing to predict the behavior
of such structures after a certain age. The degraded material
properties are calculated by introducing isotropic degradation index.
The predicted material properties are used to study the behavior of
aged dam at different ages. The dam is modeled by finite elements
and displacement and is considered as an unknown variable. The
parametric study reveals that the displacement is quite larger for
comparatively lower design life of the structure because the
degradation of elastic properties depends on the design life of the
dam. The stresses in dam cam be unexpectedly large at any age with
in the design life. The outcomes of the present study indicate the
importance of the consideration ageing effect of concrete exposed to
water for the safe design of dam throughout its life time.
Abstract: Floorplanning plays a vital role in the physical design
process of Very Large Scale Integrated (VLSI) chips. It is an
essential design step to estimate the chip area prior to the optimized
placement of digital blocks and their interconnections. Since VLSI
floorplanning is an NP-hard problem, many optimization techniques
were adopted in the literature. In this work, a music-inspired
Harmony Search (HS) algorithm is used for the fixed die outline
constrained floorplanning, with the aim of reducing the total chip
area. HS draws inspiration from the musical improvisation process of
searching for a perfect state of harmony. Initially, B*-tree is used to
generate the primary floorplan for the given rectangular hard
modules and then HS algorithm is applied to obtain an optimal
solution for the efficient floorplan. The experimental results of the
HS algorithm are obtained for the MCNC benchmark circuits.
Abstract: This paper represents the results of experimental work to investigate the suitability of a waste material (WM) for soft soil stabilisation. In addition, the effect of particle size distribution (PSD) of the waste material on its performance as a soil stabiliser was investigated. The WM used in this study is produced from the incineration processes in domestic energy power plant and it is available in two different grades of fineness (coarse waste material (CWM) and fine waste material (FWM)). An intermediate plasticity silty clayey soil with medium organic matter content has been used in this study. The suitability of the CWM and FWM to improve the physical and engineering properties of the selected soil was evaluated dependant on the results obtained from the consistency limits, compaction characteristics (optimum moisture content (OMC) and maximum dry density (MDD)); along with the unconfined compressive strength test (UCS). Different percentages of CWM were added to the soft soil (3, 6, 9, 12 and 15%) to produce various admixtures. Then the UCS test was carried out on specimens under different curing periods (zero, 7, 14, and 28 days) to find the optimum percentage of CWM. The optimum and other two percentages (either side of the optimum content) were used for FWM to evaluate the effect of the fineness of the WM on UCS of the stabilised soil. Results indicated that both types of the WM used in this study improved the physical properties of the soft soil where the index of plasticity (IP) was decreased significantly. IP was decreased from 21 to 13.64 and 13.10 with 12% of CWM and 15% of FWM respectively. The results of the unconfined compressive strength test indicated that 12% of CWM was the optimum and this percentage developed the UCS value from 202kPa to 500kPa for 28 days cured samples, which is equal, approximately 2.5 times the UCS value for untreated soil. Moreover, this percentage provided 1.4 times the value of UCS for stabilized soil-CWA by using FWM which recorded just under 700kPa after 28 days curing.
Abstract: In the years followed independence, an economic
crisis and some conflicts led to the displacement of many people
inside Georgia. The growing poverty, unemployment, low income
and its unequal distribution limited access to basic social service have
had a clear direct impact on Georgian population dynamics and its
age-sex structure. Factors influencing the changing population age
structure and urbanization include mortality, fertility, migration and
expansion of urban. In this paper presents the main factors of
changing the distribution by urban and rural areas. How different are
the urban and rural age and sex structures? Does Georgia have the
same age-sex structure among their urban and rural populations since
1950s?
Abstract: This paper presents a computational study of steady
state three dimensional very high turbulent flow and heat transfer
characteristics in a constant temperature-surfaced circular duct fitted
with 900 hemispherical inline baffles. The computations are based on
realizable k-ɛ model with standard wall function considering the
finite volume method, and the SIMPLE algorithm has been
implemented. Computational Study are carried out for Reynolds
number, Re ranging from 80000 to 120000, Prandtl Number, Pr of
0.73, Pitch Ratios, PR of 1,2,3,4,5 based on the hydraulic diameter of
the channel, hydrodynamic entry length, thermal entry length and the
test section. Ansys Fluent 15.0 software has been used to solve the
flow field. Study reveals that circular pipe having baffles has a higher
Nusselt number and friction factor compared to the smooth circular
pipe without baffles. Maximum Nusselt number and friction factor
are obtained for the PR=5 and PR=1 respectively. Nusselt number
increases while pitch ratio increases in the range of study; however,
friction factor also decreases up to PR 3 and after which it becomes
almost constant up to PR 5. Thermal enhancement factor increases
with increasing pitch ratio but with slightly decreasing Reynolds
number in the range of study and becomes almost constant at higher
Reynolds number. The computational results reveal that optimum
thermal enhancement factor of 900 inline hemispherical baffle is
about 1.23 for pitch ratio 5 at Reynolds number 120000.It also shows
that the optimum pitch ratio for which the baffles can be installed in
such very high turbulent flows should be 5. Results show that pitch
ratio and Reynolds number play an important role on both fluid flow
and heat transfer characteristics.
Abstract: Any signal transmitted over a channel is corrupted by noise and interference. A host of channel coding techniques has been proposed to alleviate the effect of such noise and interference. Among these Turbo codes are recommended, because of increased capacity at higher transmission rates and superior performance over convolutional codes. The multimedia elements which are associated with ample amount of data are best protected by Turbo codes. Turbo decoder employs Maximum A-posteriori Probability (MAP) and Soft Output Viterbi Decoding (SOVA) algorithms. Conventional Turbo coded systems employ Equal Error Protection (EEP) in which the protection of all the data in an information message is uniform. Some applications involve Unequal Error Protection (UEP) in which the level of protection is higher for important information bits than that of other bits. In this work, enhancement to the traditional Log MAP decoding algorithm is being done by using optimized scaling factors for both the decoders. The error correcting performance in presence of UEP in Additive White Gaussian Noise channel (AWGN) and Rayleigh fading are analyzed for the transmission of image with Discrete Cosine Transform (DCT) as source coding technique. This paper compares the performance of log MAP, Modified log MAP (MlogMAP) and Enhanced log MAP (ElogMAP) algorithms used for image transmission. The MlogMAP algorithm is found to be best for lower Eb/N0 values but for higher Eb/N0 ElogMAP performs better with optimized scaling factors. The performance comparison of AWGN with fading channel indicates the robustness of the proposed algorithm. According to the performance of three different message classes, class3 would be more protected than other two classes. From the performance analysis, it is observed that ElogMAP algorithm with UEP is best for transmission of an image compared to Log MAP and MlogMAP decoding algorithms.
Abstract: An experiment was conducted to elucidate the effects of turmeric powder supplementation on egg production performance of old laying hens (80 weeks of age). There were 40 hens of Hysex Brown strain used in the study. They were caged individually, and randomly divided into 4 treatment groups of diet containing 0 (control), 1, 2 and 4 % oven dried turmeric powder for 3 periods of 4 weeks; Egg production (% hen day) and feed intake of the 4 treatment groups at the commencement of the experiment were not significantly different. In addition to egg production performance (% and egg weight), feed and water intakes were measured daily, and cholesterol content of the whole egg was determined. The results indicated that feed intakes of the hen were significantly lowered when 4% turmeric powder supplemented, while there were no significant changes in water intakes. Egg production were significantly increased and maintained at a higher level by turmeric powder supplementation up to 4% compared with the control, while the weight of eggs were not significantly affected. The research markedly demonstrated that supplementation of turmeric powder up to 4% could improve and maintain egg production performance of the old laying hen at a higher level with a lower cholesterol content.
Abstract: In this study, we demonstrate the production of natural gas hydrates from permeable marine sediments with simultaneous mechanisms for methane recovery and methane-air or methane-air/carbon dioxide replacement. The simultaneous melting happens until the chemical potentials become equal in both phases as natural gas hydrate depletion continues and self-regulated methane-air replacement occurs over an arbitrary point. We observed certain point between dissociation and replacement mechanisms in the natural gas hydrate reservoir, and we call this boundary as critical methane concentration. By the way, when carbon dioxide was added, the process of chemical exchange of methane by air/carbon dioxide was observed in the natural gas hydrate. The suggested process will operate well for most global natural gas hydrate reservoirs, regardless of the operating conditions or geometrical constraints.
Abstract: Metal thin-walled members have been widely used in
building industry. Usually they are utilized as purlins, girts or ceiling
beams. Due to slenderness of thin-walled cross-sections these
structural members are prone to stability problems (e.g. flexural
buckling, lateral torsional buckling). If buckling is not
constructionally prevented their resistance is limited by buckling
strength. In practice planar members of roof or wall cladding can be
attached to thin-walled members. These elements reduce
displacement of thin-walled members and therefore increase their
buckling strength. If this effect is taken into static assessment more
economical sections of thin-walled members might be utilized and
certain savings of material might be achieved. This paper focuses on
problem of determination of critical load of steel thin-walled beams
with lateral continuous restraint which is crucial for lateral torsional
buckling assessment.
Abstract: Aluminium matrix composites with alumina
reinforcements give superior mechanical & physical properties. Their
applications in several fields like automobile, aerospace, defense,
sports, electronics, bio-medical and other industrial purposes are
becoming essential for the last several decades. In the present work,
fabrication of hybrid composite was done by Stir casting technique
using Al 6061 as a matrix with alumina and silicon carbide (SiC) as
reinforcement materials. The weight percentage of alumina is varied
from 2 to 4% and the silicon carbide weight percentage is maintained
constant at 2%. Hardness and wear tests are performed in the as cast
and heat treated conditions. Age hardening treatment was performed
on the specimen with solutionizing at 550°C, aging at two
temperatures (150 and 200°C) for different time durations. Hardness
distribution curves are drawn and peak hardness values are recorded.
Hardness increase was very sensitive with respect to the decrease in
aging temperature. There was an improvement in wear resistance of
the peak aged material when aged at lower temperature. Also
increase in weight percent of alumina, increases wear resistance at
lower temperature but opposite behavior was seen when aged at
higher temperature.
Abstract: In the past decade, the use of digital image correlation
(DIC) techniques has increased significantly in the area of
experimental mechanics, especially for materials behavior
characterization. This non-contact tool enables full field displacement
and strain measurements over a complete region of interest. The DIC
algorithm requires a random contrast pattern on the surface of the
specimen in order to perform properly. To create this pattern, the
specimen is usually first coated using a white matt paint. Next, a
black random speckle pattern is applied using any suitable method. If
the applied paint coating is too thick, its top surface may not be able
to exactly follow the deformation of the specimen, and consequently,
the strain measurement might be underestimated. In the present
article, a study of the influence of the paint thickness on the strain
underestimation is performed for different strain levels. The results
are then compared to typical paint coating thicknesses applied by
experienced DIC users. A slight strain underestimation was observed
for paint coatings thicker than about 30μm. On the other hand, this
value was found to be uncommonly high compared to coating
thicknesses applied by DIC users.
Abstract: Due to rapid advancement of powerful image
processing software, digital images are easy to manipulate and
modify by ordinary people. Lots of digital images are edited for a
specific purpose and more difficult to distinguish form their original
ones. We propose a clustering method to detect a copy-move image
forgery of JPEG, BMP, TIFF, and PNG. The process starts with
reducing the color of the photos. Then, we use the clustering
technique to divide information of measuring data by Hausdorff
Distance. The result shows that the purposed methods is capable of
inspecting the image file and correctly identify the forgery.
Abstract: The substantial development of the construction
industry has forced the cement industry, its major support, to focus
on achieving maximum productivity to meet the growing demand for
this material. This means that the reliability of a cement production
system needs to be at the highest level that can be achieved by good
maintenance. This paper studies the extent to which the
implementation of RCM is needed as a strategy for increasing the
reliability of the production systems component can be increased,
thus ensuring continuous productivity. In a case study of four Libyan
cement factories, 80 employees were surveyed and 12 top and middle
managers interviewed. It is evident that these factories usually
breakdown more often than once per month which has led to a
decline in productivity. In many times they cannot achieve the
minimum level of production amount. This has resulted from the
poor reliability of their production systems as a result of poor or
insufficient maintenance. It has been found that most of the factories’
employees misunderstand maintenance and its importance. The main
cause of this problem is the lack of qualified and trained staff, but in
addition it has been found that most employees are not found to be
motivated as a result of a lack of management support and interest. In
response to these findings, it has been suggested that the RCM
strategy should be implemented in the four factories. The results
show the importance of the development of maintenance strategies
through the implementation of RCM in these factories. The purpose
of it would be to overcome the problems that could secure the
reliability of the production systems. This study could be a useful
source of information for academic researchers and the industrial
organizations which are still experiencing problems in maintenance
practices.
Abstract: This study focuses on a novel method for dispersion
and distribution of reinforcement under high intensive shear stress to
produce metal composites. The polyacrylonitrile (PAN)-based short
carbon fiber (Csf) and Nextel 610 alumina fiber were dispersed under
high intensive shearing at mushy zone in semi-solid of A356 by a
novel method. The bundles and clusters were embedded by
infiltration of slurry into the clusters, thus leading to a uniform
microstructure. The fibers were embedded homogenously into the
aluminum around 576-580°C with around 46% of solid fraction.
Other experiments at 615°C and 568°C which are contained 0% and
90% solid respectively were not successful for dispersion and
infiltration of aluminum into bundles of Csf. The alumina fiber has
been cracked by high shearing load. The morphologies and
crystalline phase were evaluated by SEM and XRD. The adopted
thixo-process effectively improved the adherence and distribution of
Csf into Al that can be developed to produce various composites by
thixomixing.
Abstract: Mammography is widely used technique for breast cancer
screening. There are various other techniques for breast cancer screening
but mammography is the most reliable and effective technique. The
images obtained through mammography are of low contrast which
causes problem for the radiologists to interpret. Hence, a high quality
image is mandatory for the processing of the image for extracting any
kind of information from it. Many contrast enhancement algorithms have
been developed over the years. In the present work, an efficient
morphology based technique is proposed for contrast enhancement of
masses in mammographic images. The proposed method is based on
Multiscale Morphology and it takes into consideration the scale of the
structuring element. The proposed method is compared with other stateof-
the-art techniques. The experimental results show that the proposed
method is better both qualitatively and quantitatively than the other
standard contrast enhancement techniques.
Abstract: Potassium borates, which are widely used in welding
and metal refining industry, as a lubricating oil additive, cement
additive, fiberglass additive and insulation compound, are one of the
important groups of borate minerals. In this study the production of a
potassium borate mineral via hydrothermal method is aimed. The
potassium source of potassium nitrate (KNO3) was used along with a
sodium source of sodium hydroxide (NaOH) and boron source of
boric acid (H3BO3). The constant parameters of reaction temperature
and reaction time were determined as 80°C and 1 h, respectively. The
molar ratios of 1:1:3 (as KNO3:NaOH:H3BO3), 1:1:4, 1:1:5, 1:1:6
and 1:1:7 were used. Following the synthesis the identifications of
the produced products were conducted by X-Ray Diffraction (XRD),
Fourier Transform Infrared Spectroscopy (FT-IR) and Raman
Spectroscopy. The results of the experiments and analysis showed in
the ratio of 1:1:6, the Santite mineral with powder diffraction file
number (pdf no.) of 01-072-1688, which is known as potassium
pentaborate (KB5O8·4H2O) was synthesized as best.
Abstract: This paper presents the results of an experimental
study undertaken to evaluate the local bond stress-slip response of
short embedment of reinforcing bars in normal concrete (NC) and
high performance fiber reinforced cement composites (HPFRCC)
blocks. Long embedment was investigated as well to gain insights on
the distribution of strain, slip, bar stress and bond stress along the bar
especially in post-yield range. A total of 12 specimens were tested,
by means of pull-out of the reinforcing bars from concrete blocks. It
was found that the enhancement of local bond strength can be
reached up to 50% and ductility of the bond behavior was improved
significantly if HPFRCC is used. Also, under a constant strain at
loaded end, HPFRCC has delayed yielding of bars at other location
from the loaded end. Hence, the reduction of bond stress was slower
for HPFRCC in comparison with NC. Due to the same reason, the
total slips at loaded end for HPFRCC was smaller than NC as
expected. Test results indicated that HPFRCC has better bond slip
behavior which makes it a suitable material to be employed in
anchorage zone such as beam-column joints.