Abstract: This paper presents a hand vein authentication system
using fast spatial correlation of hand vein patterns. In order to
evaluate the system performance, a prototype was designed and a
dataset of 50 persons of different ages above 16 and of different
gender, each has 10 images per person was acquired at different
intervals, 5 images for left hand and 5 images for right hand. In
verification testing analysis, we used 3 images to represent the
templates and 2 images for testing. Each of the 2 images is matched
with the existing 3 templates. FAR of 0.02% and FRR of 3.00 %
were reported at threshold 80. The system efficiency at this threshold
was found to be 99.95%. The system can operate at a 97% genuine
acceptance rate and 99.98 % genuine reject rate, at corresponding
threshold of 80. The EER was reported as 0.25 % at threshold 77. We
verified that no similarity exists between right and left hand vein
patterns for the same person over the acquired dataset sample.
Finally, this distinct 100 hand vein patterns dataset sample can be
accessed by researchers and students upon request for testing other
methods of hand veins matching.
Abstract: The object of this paper is to design and analyze a
proportional – integral (PI) control for positive output elementary
super lift Luo converter (POESLLC), which is the start-of-the-art
DC-DC converter. The positive output elementary super lift Luo
converter performs the voltage conversion from positive source
voltage to positive load voltage. This paper proposes a
development of PI control capable of providing the good static and
dynamic performance compared to proportional – integralderivative
(PID) controller. Using state space average method
derives the dynamic equations describing the positive output
elementary super lift luo converter and PI control is designed. The
simulation model of the positive output elementary super lift Luo
converter with its control circuit is implemented in
Matlab/Simulink. The PI control for positive output elementary
super lift Luo converter is tested for transient region, line changes,
load changes, steady state region and also for components
variations.
Abstract: In this paper, we present an experimental testing for
a new algorithm that determines an optimal controller-s coefficients
for output variance reduction related to Linear Time Invariant (LTI)
Systems. The algorithm features simplicity in calculation, generalization
to minimal and non-minimal phase systems, and could be
configured to achieve reference tracking as well as variance reduction
after compromising with the output variance. An experiment of DCmotor
velocity control demonstrates the application of this new
algorithm in designing the controller. The results show that the
controller achieves minimum variance and reference tracking for a
preset velocity reference relying on an identified model of the motor.
Abstract: Turkey has 72 % of total world boron reserves on the
basis of B2O3.Borates that is a refined form of boron minerals have a
wide range of applications. Zinc borates can be used as multifunctional
synergistic additives. The most important properties are
low solubility in water and high dehydration temperature. Zinc
borates dehydrate above 290°C and anhydrous zinc borate has
thermal resistance about 400°C. Zinc borates can be synthesized
using several methods such as hydrothermal and solid-state
processes. In this study, the solid-state method was applied between
500 and 800°C using the starting materials of ZnO and H3BO3 with
1:4 mole ratio. The reaction time was determined as 4 hours after
some preliminary experiments. After the synthesis, the crystal
structure and the morphology of the products were examined by XRay
Diffraction (XRD), Fourier Transform Infrared Spectroscopy
(FT-IR) and Raman Spectrometer. As a result the form of ZnB4O7
was synthesized with the highest crystal score at 800°C.
Abstract: The broadcast problem including the plan design is
considered. The data are inserted and numbered at predefined order
into customized size relations. The server ability to create a full,
regular Broadcast Plan (RBP) with single and multiple channels after
some data transformations is examined. The Regular Geometric
Algorithm (RGA) prepares a RBP and enables the users to catch their
items avoiding energy waste of their devices. Moreover, the
Grouping Dimensioning Algorithm (GDA) based on integrated
relations can guarantee the discrimination of services with a
minimum number of channels. This last property among the selfmonitoring,
self-organizing, can be offered by servers today
providing also channel availability and less energy consumption by
using smaller number of channels. Simulation results are provided.
Abstract: The vast rural landscape in the southern United States
is conspicuously characterized by the hedgerow trees or groves. The
patchwork landscape of fields surrounded by high hedgerows is a
traditional and familiar feature of the American countryside.
Hedgerows are in effect linear strips of trees, groves, or woodlands,
which are often critical habitats for wildlife and important for the
visual quality of the landscape. As landscape interfaces, hedgerows
define the spaces in the landscape, give the landscape life and
meaning, and enrich ecologies and cultural heritages of the American
countryside. Although hedgerows were originally intended as fences
and to mark property and townland boundaries, they are not merely
the natural or man-made additions to the landscape--they have
gradually become “naturalized" into the landscape, deeply rooted in
the rural culture, and now formed an important component of the
southern American rural environment. However, due to the ever
expanding real estate industry and high demand for new residential
development, substantial areas of authentic hedgerow landscape in
the southern United States are being urbanized. Using Hudson Farm
as an example, this study illustrated guidelines of how hedgerows can
be integrated into town planning as green infrastructure and
landscape interface to innovate and direct sustainable land use, and
suggest ways in which such vernacular landscapes can be preserved
and integrated into new development without losing their contextual
inspiration.
Abstract: Fractional delay FIR filters design method based on
the differential evolution algorithm is presented. Differential evolution
is an evolutionary algorithm for solving a global optimization problems in the continuous search space. In the proposed approach,
an evolutionary algorithm is used to determine the coefficients of
a fractional delay FIR filter based on the Farrow structure. Basic
differential evolution is enhanced with a restricted mating technique,
which improves the algorithm performance in terms of convergence
speed and obtained solution. Evolutionary optimization is carried out by minimizing an objective function which is based on the amplitude
response and phase delay errors. Experimental results show that the proposed algorithm leads to a reduction in the amplitude response and phase delay errors relative to those achieved with the Least-Squares
method.
Abstract: Truss optimization problem has been vastly studied
during the past 30 years and many different methods have been
proposed for this problem. Even though most of these methods
assume that the design variables are continuously valued, in reality,
the design variables of optimization problems such as cross-sectional
areas are discretely valued. In this paper, an improved hill climbing
and an improved simulated annealing algorithm have been proposed
to solve the truss optimization problem with discrete values for crosssectional
areas. Obtained results have been compared to other
methods in the literature and the comparison represents that the
proposed methods can be used more efficiently than other proposed
methods
Abstract: Deniable authentication is a new protocol which not only enables a receiver to identify the source of a received message but also prevents a third party from identifying the source of the message. The proposed protocol in this paper makes use of bilinear pairings over elliptic curves, as well as the Diffie-Hellman key exchange protocol. Besides the security properties shared with previous authentication protocols, the proposed protocol provides the same level of security with smaller public key sizes.
Abstract: The sustainability of a place depends on a series of factors which contribute to the quality of life, sense of place and recognition of identity. An activity like walking, which in itself is obviously ''sustainable'', can become non sustainable if the context in which it is carried out does not meet the conditions for an adequate quality of life. This work is aimed at proposing the analytical method of Place Maker to identify the elements that do not feature in traditional mapping and which constitute the contemporary identity of the places, and the relative complex map to represent those elements and support sustainable urban identity design. The method's potential for areas with a predominantly pedestrian vocation is illustrated by means of the case study of the Ramblas in Barcelona.
Abstract: This paper aims to explain the project carried out at
the University of Cordoba, specifically at the High Polytechnic
School in collaboration with two other organizations belonging to the
Andalusian Ministry of Innovation, Science and Business:
Andalusian Innovation and Development Agency (IDEA agency) [1]
and the Territorial Net of Entrepreneurship Support (in Spanish Red
Territorial de Apoyo al Emprendedor) [11].
The project is being developed in several stages of which only the
first one has already been completed. However, several important
preliminary results derive from it, based mainly in the description of
the nature of entrepreneurship in the field of university education and
its impact on student-s competency as recommended by the European
Higher Education Area. Some problems holding back the correct
future development will also be shown as derived from the specific
context of application of the project.
Abstract: Cenozoic basalts found in Jiangsu province of eastern
China include tholeiites and alkali basalts. The present paper analyzed
the major, trace elements, rare earth elements of these Cenozoic
basalts and combined with Sr-Nd isotopic compositions proposed by
Chen et al. (1990)[1] in the literatures to discuss the petrogenesis of
these basalts and the geochemical characteristics of the source mantle.
Based on major, trace elements and fractional crystallization model
established by Brooks and Nielsen (1982)[2] we suggest that the
basaltic magma has experienced olivine + clinopyroxene fractionation
during its evolution. The chemical compositions of basaltic rocks from
Jiangsu province indicate that these basalts may belong to the same
magmatic system. Spidergrams reveal that Cenozoic basalts from
Jiangsu province have geochemical characteristics similar to those of
ocean island basalts(OIB). The slight positive Nb and Ti anomalies
found in basaltic rocks of this study suggest the presence of Ti-bearing
minerals in the mantle source and these Ti-bearing minerals had
contributed to basaltic magma during partial melting, indicating a
metasomatic event might have occurred before the partial melting.
Based on the Sr vs. Nd isotopic ratio plots, we suggest that Jiangsu
basalts may be derived from partial melting of mantle source which
may represent two-end members mixing of DMM and EM-I. Some
Jiangsu basaltic magma may be derived from partial melting of EM-I
heated by the upwelling asthenospheric mantle or asthenospheric
diapirism.
Abstract: Roundabout work on the principle of circulation and
entry flows, where the maximum entry flow rates depend largely on
circulating flow bearing in mind that entry flows must give away to
circulating flows. Where an existing roundabout has a road hump
installed at the entry arm, it can be hypothesized that the kinematics
of vehicles may prevent the entry arm from achieving optimum
performance. Road humps are traffic calming devices placed across
road width solely as speed reduction mechanism. They are the
preferred traffic calming option in Malaysia and often used on single
and dual carriageway local routes. The speed limit on local routes is
30mph (50 km/hr). Road humps in their various forms achieved the
biggest mean speed reduction (based on a mean speed before traffic
calming of 30mph) of up to 10mph or 16 km/hr according to the UK
Department of Transport. The underlying aim of reduced speed
should be to achieve a 'safe' distribution of speeds which reflects the
function of the road and the impacts on the local community.
Constraining safe distribution of speeds may lead to poor drivers
timing and delayed reflex reaction that can probably cause accident.
Previous studies on road hump impact have focused mainly on speed
reduction, traffic volume, noise and vibrations, discomfort and delay
from the use of road humps. The paper is aimed at optimal entry and
circulating flow induced by road humps. Results show that
roundabout entry and circulating flow perform better in
circumstances where there is no road hump at entrance.
Abstract: The problem of FIR system parameter estimation has been considered in the paper. A new robust recursive algorithm for simultaneously estimation of parameters and scale factor of prediction residuals in non-stationary environment corrupted by impulsive noise has been proposed. The performance of derived algorithm has been tested by simulations.
Abstract: Carbon nanotubes (CNTs) with their high mechanical,
electrical, thermal and chemical properties are regarded as promising
materials for many different potential applications. Having unique
properties they can be used in a wide range of fields such as
electronic devices, electrodes, drug delivery systems, hydrogen
storage, textile etc. Catalytic chemical vapor deposition (CCVD) is a
common method for CNT production especially for mass production.
Catalysts impregnated on a suitable substrate are important for
production with chemical vapor deposition (CVD) method. Iron
catalyst and MgO substrate is one of most common catalyst-substrate
combination used for CNT. In this study, CNTs were produced by
CCVD of acetylene (C2H2) on magnesium oxide (MgO) powder
substrate impregnated by iron nitrate (Fe(NO3)3•9H2O) solution. The
CNT synthesis conditions were as follows: at synthesis temperatures
of 500 and 800°C multiwall and single wall CNTs were produced
respectively. Iron (Fe) catalysts were prepared by with Fe:MgO ratio
of 1:100, 5:100 and 10:100. The duration of syntheses were 30 and
60 minutes for all temperatures and catalyst percentages. The
synthesized materials were characterized by thermal gravimetric
analysis (TGA), transmission electron microscopy (TEM) and Raman
spectroscopy.
Abstract: This article experimentally investigates the
thermal performance of thermoelectric air-cooling module
which comprises a thermoelectric cooler (TEC) and an
air-cooling heat sink. The influences of input current and heat
load are determined. And performances under each situation
are quantified by thermal resistance analysis. Since TEC
generates Joule heat, this nature makes construction of thermal
resistance network difficult. To simplify the analysis, this
article emphasizes on the resistance heat load might meet when
passing through the device. Therefore, the thermal resistances
in this paper are to divide temperature differences by heat load.
According to the result, there exists an optimum input current
under every heating power. In this case, the optimum input
current is around 6A or 7A. The performance of the heat sink
would be improved with TEC under certain heating power and
input current, especially at a low heat load. According to the
result, the device can even make the heat source cooler than the
ambient. However, TEC is not always effective at every heat
load and input current. In some situation, the device works
worse than the heat sink without TEC. To determine the
availability of TEC, this study figures out the effective
operating region in which the TEC air-cooling module works
better than the heat sink without TEC. The result shows that
TEC is more effective at a lower heat load. If heat load is too
high, heat sink with TEC will perform worse than without TEC.
The limit of this device is 57W. Besides, TEC is not helpful if
input current is too high or too low. There is an effective range
of input current, and the range becomes narrower when the heat
load grows.
Abstract: The three-time-scale plant model of a wind power
generator, including a wind turbine, a flexible vertical shaft, a Variable
Inertia Flywheel (VIF) module, an Active Magnetic Bearing (AMB)
unit and the applied wind sequence, is constructed. In order to make
the wind power generator be still able to operate as the spindle speed
exceeds its rated speed, the VIF is equipped so that the spindle speed
can be appropriately slowed down once any stronger wind field is
exerted. To prevent any potential damage due to collision by shaft
against conventional bearings, the AMB unit is proposed to regulate
the shaft position deviation. By singular perturbation order-reduction
technique, a lower-order plant model can be established for the
synthesis of feedback controller. Two major system parameter
uncertainties, an additive uncertainty and a multiplicative uncertainty,
are constituted by the wind turbine and the VIF respectively.
Frequency Shaping Sliding Mode Control (FSSMC) loop is proposed
to account for these uncertainties and suppress the unmodeled
higher-order plant dynamics. At last, the efficacy of the FSSMC is
verified by intensive computer and experimental simulations for
regulation on position deviation of the shaft and counter-balance of
unpredictable wind disturbance.
Abstract: The main focus of the work was concerned with hydrodynamic and thermal analysis of the plate heat exchanger channel with corrugation patterns suggested to be triangular, sinusoidal, and square corrugation. This study was to numerically model and validate the triangular corrugated channel with dimensions/parameters taken from open literature, and then model/analyze both sinusoidal, and square corrugated channel referred to the triangular model. Initially, 2D modeling with local extensive analysis for triangular corrugated channel was carried out. By that, all local pressure drop, wall shear stress, friction factor, static temperature, heat flux, Nusselt number, and surface heat coefficient, were analyzed to interpret the hydrodynamic and thermal phenomena occurred in the flow. Furthermore, in order to facilitate confidence in this model, a comparison between the values predicted, and experimental results taken from literature for almost the same case, was done. Moreover, a holistic numerical study for sinusoidal and square channels together with global comparisons with triangular corrugation under the same condition, were handled. Later, a comparison between electric, and fluid cooling through varying the boundary condition was achieved. The constant wall temperature and constant wall heat flux boundary conditions were employed, and the different resulted Nusselt numbers as a consequence were justified. The results obtained can be used to come up with an optimal design, a 'compromise' between heat transfer and pressure drop.
Abstract: The aim of this study is evaluating the antinociceptive
and anti-inflamatory activity of Geum kokanicum. After
determination total extract LD50, different doses of extract were
chosen for intrapritoneal injections. In inflammation test, male NMRI
mice were divided into 6 groups: control (normal saline), positive
control (Dexamethasone 15mg/kg), and total extract (0.025, 0.05,
0.1, and 0.2 gr/kg). The inflammation was produced by xyleneinduced
edema. In order to evaluate the antinociceptive effect of total
extract, formalin test was used. Mice were divided into 6 groups:
control, positive control (morphine 10mg/kg), and 4 groups which
received total extract. Then they received Formalin. The animals
were observed for the reaction to pain. Data were analyzed using
One-way ANOVA followed by Tukey-Kramer multiple comparison
test. LD50 was 1 gr/kg. Data indicated that 0.5,0.1 and 0.2 gr/kg
doses of total extract have particular antinociceptive and antiinflammatory
effects in a comparison with control (P
Abstract: Magnesium is used implant material potentially for
non-toxicity to the human body. Due to the excellent
bio-compatibility, Mg alloys is applied to implants avoiding removal
second surgery. However, it is found commercial magnesium alloys
including aluminum has low corrosion resistance, resulting
subcutaneous gas bubbles and consequently the approach as
permanent bio-materials. Generally, Aluminum is known to pollution
substance, and it raises toxicity to nervous system. Therefore
especially Mg-35Zn-3Ca alloy is prepared for new biodegradable
materials in this study. And the pulsed power is used in
constant-current mode of DC power kinds of anodization. Based on
the aforementioned study, it examines corrosion resistance and
biocompatibility by effect of current and frequency variation. The
surface properties and thickness were compared using scanning
electronic microscopy. Corrosion resistance was assessed via
potentiodynamic polarization and the effect of oxide layer on the body
was assessed cell viability. Anodized Mg-35Zn-3Ca alloy has good
biocompatibility in vitro by current and frequency variation.