Abstract: Zn alloy and composite coatings are widely used in
buildings and structures, automobile and fasteners industries to
protect steel component from corrosion. In this paper, Zn-Ni-Al2O3
nanocomposite coatings were electrodeposited on mild steel using a
novel sol enhanced electroplating method. In this method, transparent
Al2O3 sol was added into the acidic Zn-Ni bath to produced Zn-Ni-
Al2O3 nanocomposite coatings. The effect of alumina sol on the
electrodeposition process, and coating properties was investigated
using cyclic voltammetry, XRD, ESEM and Tafel test. Results from
XRD tests showed that the structure of all coatings was single γ-
Ni5Zn21 phase. Cyclic voltammetry results showed that the
electrodeposition overpotential was lower in the presence of alumina
sol in the bath, and caused the reduction potential of Zn-Ni to shift to
more positive values. Zn-Ni-Al2O3 nanocomposite coatings produced
more uniform and compact deposits, with fine grained microstructure
when compared to Zn-Ni coatings. The corrosion resistance of Zn-Ni
coatings was improved significantly by incorporation of alumina
nanoparticles into the coatings.
Abstract: The purpose of this paper is to present a modeling and
control of a quarter-car active suspension system with unknown
mass, unknown time-delay and road disturbance. The objective of
designing the controller is to derive a control law to achieve stability
of the system and convergence that can considerably improve ride
comfort and road disturbance handling. This is accomplished by
using Routh-Hurwitz criterion based on defined parameters.
Mathematical proof is given to show the ability of the designed
controller to ensure the target of design, implementation with the
active suspension system and enhancement dispersion oscillation of
the system despite these problems. Simulations were also performed
to control quarter car suspension, where the results obtained from
these simulations verify the validity of the proposed design.
Abstract: Contemporary theories of sustainability, concerning
the natural and built environment, have recently introduced an
environmental attitude towards the architectural design that, in turn,
affects the practice of conservation and reuse of the existing building
stock. This paper presents an environmentally friendly approach
towards the conservation of vernacular architecture and it is based on
the results of a research program which involved the investigation of
sustainable design elements of traditional buildings in Cyprus. The
research in question showed that Cypriot vernacular architecture gave
more emphasis on cooling rather than heating strategies. Another
notable finding of the investigation was the great importance given to
courtyards as they enhance considerably, and in various ways, the
microclimatic conditions of the immediate environment with
favorable results throughout the year. Moreover, it was shown that
the reduction in temperature fluctuation observed in the closed and
semi-open spaces, compared to the respective temperature fluctuation
of the external environment -due to the thermal inertia of the building
envelope- helps towards the achievement of more comfortable living
conditions within traditional dwellings. This paper concludes with a
proposal of a sustainable approach towards the conservation of the
existing environment and the introduction of new environmental
criteria for the conservation of traditional buildings, beyond the
aesthetic, morphological and structural ones that are generally
applied.
Abstract: The using of waste materials in the construction
industry can reduce the dependence on the natural aggregates which
are going at the end to deplete. The glass waste is generated in a huge
amount which can make one of its disposals in concrete industry
effective not only as a green solution but also as an advantage to
enhance the performance of mechanical properties and durability of
concrete. This article reports the performance of concrete specimens
containing different percentages of milled glass waste as a partial
replacement of cement (Powder), when they are subject to cycles of
freezing and thawing. The tests were conducted on 75-mm cubes and
75 x 75 x 300-mm prisms. Compressive strength based on laboratory
testing and non-destructive ultrasonic pulse velocity test were
performed during the action of freezing-thawing cycles (F/T). The
results revealed that the incorporation of glass waste in concrete
mixtures is not only feasible but also showed generally better strength
and durability performance than control concrete mixture. It may be
said that the recycling of waste glass in concrete mixes is not only a
disposal way, but also it can be an exploitation in concrete industry.
Abstract: A knowledge base stores facts and rules about the
world that applications can use for the purpose of reasoning. By
applying the concept of granular computing to a knowledge base,
several advantages emerge. These can be harnessed by applications
to improve their capabilities and performance. In this paper, the
concept behind such a construct, called a granular knowledge cube,
is defined, and its intended use as an instrument that manages to
cope with different data types and detect knowledge domains is
elaborated. Furthermore, the underlying architecture, consisting of the
three layers of the storing, representing, and structuring of knowledge,
is described. Finally, benefits as well as challenges of deploying it
are listed alongside application types that could profit from having
such an enhanced knowledge base.
Abstract: Si ion implantation was widely used to synthesize
specimens of SiO2 containing supersaturated Si and subsequent high
temperature annealing induces the formation of embedded
luminescent Si nanocrystals. In this work, the potentialities of excimer
UV-light (172 nm, 7.2 eV) irradiation and rapid thermal annealing
(RTA) to enhance the photoluminescence and to achieve low
temperature formation of Si nanocrystals have been investigated. The
Si ions were introduced at acceleration energy of 180 keV to fluence of
7.5 x 1016 ions/cm2. The implanted samples were subsequently
irradiated with an excimer-UV lamp. After the process, the samples
were rapidly thermal annealed before furnace annealing (FA).
Photoluminescence spectra were measured at various stages at the
process. We found that the luminescence intensity is strongly
enhanced with excimer-UV irradiation and RTA. Moreover, effective
visible photoluminescence is found to be observed even after FA at
900 oC, only for specimens treated with excimer-UV lamp and RTA.
We also prepared specimens of Si nanocrystals embedded in a SiO2 by
reactive pulsed laser deposition (PLD) in an oxygen atmosphere. We
will make clear the similarities and differences with the way of
preparation.
Abstract: This study aims at developing a novel cold asphalt
concrete binder course mixture by using Ordinary Portland Cement
(OPC) as a replacement for conventional mineral filler (0%-100%)
with new by-product material (LJMU-A2) used as a supplementary
cementitious material. With this purpose, cold asphalt concrete binder
course mixtures with cationic emulsions were studied by means of
stiffness modulus whereas water sensitivity was assessed by
measuring the stiffness modulus ratio before and after sample
conditioning.
The results indicate that a substantial enhancement in the stiffness
modulus and a considerable improvement of water sensitivity
resistance is achieved by adding LJMU-A2 to the cold asphalt
mixtures as a supplementary cementitious material. Moreover, the
addition of LJMU-A2 to those mixtures leads to a stiffness modulus
after 2-day curing compared to that obtained with Portland cement,
which occurs after 7-day curing.
Abstract: Mitigating soil erosion, especially in Mediterranean
countries such as Greece, is essential in order to maintain
environmental and agricultural sustainability. In this paper, scientific
publications related to soil erosion studies in Greece were reviewed
and categorized. To accomplish this, the online search engine of
Scopus was used. The key words were “soil”, “erosion” and
“Greece.” An analysis of the published articles was conducted at
three levels: i) type of publication, ii) chronologic and iii) thematic. A
hundred and ten publications published in scientific journals were
reviewed. The results showed that the awareness regarding the soil
erosion in Greece has increased only in the last decades. The
publications covered a wide range of thematic categories such as the
type of studied areas, the physical phenomena that trigger and
influence the soil erosion, the negative anthropogenic impacts on
them, the assessment tools that were used in order to examine the
threat and the proper management. The analysis of these articles was
significant and necessary in order to find the scientific gaps of soil
erosion studies in Greece and help enhance the sustainability of soil
management in the future.
Abstract: It is an established fact that polymers have several
physical limitations such as low stiffness and low resistance to
impact on loading. Hence, polymers do not usually have requisite
mechanical strength for application in various fields. The
reinforcement by high strength fibers provides the polymer
substantially enhanced mechanical properties and makes them more
suitable for a large number of diverse applications. This research
evaluates the effects of particulate Cow bone and Groundnut shell
additions on the mechanical properties and microstructure of cow
bone and groundnut shell reinforced epoxy composite in order to
assess the possibility of using it as a material for engineering
applications. Cow bone and groundnut shell particles reinforced with
epoxy (CBRPC and GSRPC) was prepared by varying the cow bone
and groundnut shell particles from 0-25 wt% with 5 wt% intervals. A
Hybrid of the Cow bone and Groundnut shell (HGSCB) reinforce
with epoxy was also prepared. The mechanical properties of the
developed composites were investigated. Optical microscopy was
used to examine the microstructure of the composites. The results
revealed that mechanical properties did not increase uniformly with
additions in filler but exhibited maximum properties at specific
percentages of filler additions. From the Microscopic evaluation, it
was discovered that homogeneity decreases with increase in % filler,
this could be due to poor interfacial bonding.
Abstract: HZSM-5 zeolites modified by iron and phosphorus
were applied in catalytic cracking of butene. N2 adsorption and
NH3-TPD were employed to measure the structure and acidity of
catalysts. The results indicate that increasing phosphorus loading
decreased surface area, pore volume and strong acidity of catalysts.
The addition of phosphorus significantly decreased butene conversion
and promoted propylene selectivity. The catalytic performance of
catalyst was strongly dependent on the reaction conditions.
Appropriate reaction conditions could suppress side reactions and
enhance propylene selectivity.
Abstract: Fibre cement plates, often used in construction,
generally are made using quartz as an inert material, cement as a
binder and cellulose as a fibre. This paper, first of all, investigates the
mechanical properties and durability of fibre cement plates when
quartz is both partly and fully replaced with diatomite. Diatomite
does not only have lower density compared to quartz but also has
high pozzolanic activity. The main objective of this paper is the
investigation of the effects of supplementary cementing materials
(SCMs) on the short and long term mechanical properties and
durability characteristics of fibre cement plates prepared using
diatomite. Supplementary cementing materials such as ground
granulated blast furnace slug (GGBS) and fly ash (FA) are used in
this study. Volume proportions of 10, 20, 30 and 40% of GGBS and
FA are used as partial replacement materials to cement. Short and
long term mechanical properties such as compressive and flexural
strengths as well as sorptivity characteristics and mass were
investigated. Consistency and setting time at each replacement levels
of SCMs were also recorded. The effects of using supplementary
cementing materials on the carbonation and sulphate resistance of
fibre cement plates were then experimented. The results, first of all,
show that the use of diatomite as a full or partial replacement to
quartz resulted in a systematic decrease in total mass of the fibre
cement plates. The reduction of mass was largely due to the lower
density and finer particle size of diatomite compared to quartz. The
use of diatomite did not only reduce the mass of these plates but also
increased the compressive strength significantly as a result of its high
pozzolanic activity. The replacement levels of both GGBS and FA
resulted in a systematic decrease in short term compressive strength
with increasing replacement levels. This was essentially expected as
the total rate of hydration is much lower in GGBS and FA than that
of cement. Long term results however, indicated that the compressive
strength of fibre cement plates prepared using both GGBS and FA
increases with time and hence the compressive strength of plates
prepared using SCMs is either equivalent or more than the
compressive strength of plates prepared using cement alone.
Durability characteristics of fibre cement plates prepared using SCMs
were enhanced significantly. Measurements of sopritivty
characteristics were also indicated that the plates prepared using
SCMs has much lower water absorption capacities compared to
plates prepared cement alone. Much higher resistance to carbonation
and sulphate attach were observed with plates prepared using SCMs.
The results presented in this paper show that the use of SCMs does
not only support the production of more sustainable construction
materials but also enhances the mechanical properties and durability
characteristics of fibre cement plates.
Abstract: This study, for its research subjects, uses patients who
had undergone total knee replacement surgery from the database of the
National Health Insurance Administration. Through the review of
literatures and the interviews with physicians, important factors are
selected after careful screening. Then using Cross Entropy Method,
Genetic Algorithm Logistic Regression, and Particle Swarm
Optimization, the weight of each factor is calculated and obtained. In
the meantime, Excel VBA and Case Based Reasoning are combined
and adopted to evaluate the system. Results show no significant
difference found through Genetic Algorithm Logistic Regression and
Particle Swarm Optimization with over 97% accuracy in both
methods. Both ROC areas are above 0.87. This study can provide
critical reference to medical personnel as clinical assessment to
effectively enhance medical care quality and efficiency, prevent
unnecessary waste, and provide practical advantages to resource
allocation to medical institutes.
Abstract: Experimental investigations of the DC electric field effect on thermal decomposition of biomass, formation of the axial flow of volatiles (CO, H2, CxHy), mixing of volatiles with swirling airflow at low swirl intensity (S ≈ 0.2-0.35), their ignition and on formation of combustion dynamics are carried out with the aim to understand the mechanism of electric field influence on biomass gasification, combustion of volatiles and heat energy production. The DC electric field effect on combustion dynamics was studied by varying the positive bias voltage of the central electrode from 0.6 kV to 3 kV, whereas the ion current was limited to 2 mA. The results of experimental investigations confirm the field-enhanced biomass gasification with enhanced release of volatiles and the development of endothermic processes at the primary stage of thermochemical conversion of biomass determining the field-enhanced heat energy consumption with the correlating decrease of the flame temperature and heat energy production at this stage of flame formation. Further, the field-enhanced radial expansion of the flame reaction zone correlates with a more complete combustion of volatiles increasing the combustion efficiency by 3% and decreasing the mass fraction of CO, H2 and CxHy in the products, whereas by 10% increases the average volume fraction of CO2 and the heat energy production downstream the combustor increases by 5-10%
Abstract: Total Quality Management (TQM) refers to management methods used to enhance quality and productivity in business organizations. Total Quality Management (TQM) has become a frequently used term in discussions concerning quality. Total Quality management has brought rise in demands on the organizations policy and the customers have gained more importance in the organizations focus. TQM is considered as an important management tool, which helps the organizations to satisfy their customers. In present research critical success factors includes management commitment, customer satisfaction, continuous improvement, work culture and environment, supplier quality management, training and development, employee satisfaction and product/process design are studied. A questionnaire is developed to implement these critical success factors in implementation of total quality management in Indian industry. Questionnaires filled by consulting different industrial organizations. Data collected from questionnaires is analyzed by descriptive and importance indexes.
Abstract: This study was conducted to examine the effectiveness of Teaching Games For Understanding (TGFU) in improving the hockey tactical skills and state self-confidence among 16-year-old students. Two hundred fifty-nine (259) school students were selected for the study based on the intact sampling method. One class was used as the control group (Boys=60, Girls=70), while another as the treatment group (Boys=60, Girls=69) underwent intervention with TGFU in physical education class conducted twice a week for four weeks. The Games Performance Assessment Instrument was used to observe the hockey tactical skills and The State Self-Confidence Inventory was used to determine the state of self-confidence among the students. After four weeks, ANCOVA analysis indicated the treatment groups had significant improvement in hockey tactical skills with F (1, 118) =313.37, p
Abstract: This paper focuses on a critical component of the
situational awareness (SA), the control of autonomous vertical flight
for vectored thrust aerial vehicle (VTAV). With the SA strategy, we
proposed a neural network motion control procedure to address the
dynamics variation and performance requirement difference of flight
trajectory for a VTAV. This control strategy with using of NARMAL2
neurocontroller for chosen model of VTAV has been verified by
simulation of take-off and forward maneuvers using software
package Simulink and demonstrated good performance for fast
stabilization of motors, consequently, fast SA with economy in
energy can be asserted during search-and-rescue operations.
Abstract: This paper presents a computational study of steady
state three dimensional very high turbulent flow and heat transfer
characteristics in a constant temperature-surfaced circular duct fitted
with 900 hemispherical inline baffles. The computations are based on
realizable k-ɛ model with standard wall function considering the
finite volume method, and the SIMPLE algorithm has been
implemented. Computational Study are carried out for Reynolds
number, Re ranging from 80000 to 120000, Prandtl Number, Pr of
0.73, Pitch Ratios, PR of 1,2,3,4,5 based on the hydraulic diameter of
the channel, hydrodynamic entry length, thermal entry length and the
test section. Ansys Fluent 15.0 software has been used to solve the
flow field. Study reveals that circular pipe having baffles has a higher
Nusselt number and friction factor compared to the smooth circular
pipe without baffles. Maximum Nusselt number and friction factor
are obtained for the PR=5 and PR=1 respectively. Nusselt number
increases while pitch ratio increases in the range of study; however,
friction factor also decreases up to PR 3 and after which it becomes
almost constant up to PR 5. Thermal enhancement factor increases
with increasing pitch ratio but with slightly decreasing Reynolds
number in the range of study and becomes almost constant at higher
Reynolds number. The computational results reveal that optimum
thermal enhancement factor of 900 inline hemispherical baffle is
about 1.23 for pitch ratio 5 at Reynolds number 120000.It also shows
that the optimum pitch ratio for which the baffles can be installed in
such very high turbulent flows should be 5. Results show that pitch
ratio and Reynolds number play an important role on both fluid flow
and heat transfer characteristics.
Abstract: In this study, the experiments were carried out to
determine the best coolant for the quenching process among waterbased
silica, alumina, titania and copper oxide nanofluids (0.1 vol%).
A sphere made up off brass material was used in the experiments.
When the spherical test specimen was heated at high temperatures, it
was suddenly immersed into the nanofluids. All experiments were
carried out at saturated conditions and under atmospheric pressure.
After the experiments, the cooling curves were obtained by using the
temperature-time data of the specimen. The experimental results
showed that the cooling performance of test specimen depended on
the type of nanofluids. The silica nanoparticles enhanced the
performance of boiling heat transfer and it is the best coolant for the
quenching among other nanoparticles.
Abstract: Any signal transmitted over a channel is corrupted by noise and interference. A host of channel coding techniques has been proposed to alleviate the effect of such noise and interference. Among these Turbo codes are recommended, because of increased capacity at higher transmission rates and superior performance over convolutional codes. The multimedia elements which are associated with ample amount of data are best protected by Turbo codes. Turbo decoder employs Maximum A-posteriori Probability (MAP) and Soft Output Viterbi Decoding (SOVA) algorithms. Conventional Turbo coded systems employ Equal Error Protection (EEP) in which the protection of all the data in an information message is uniform. Some applications involve Unequal Error Protection (UEP) in which the level of protection is higher for important information bits than that of other bits. In this work, enhancement to the traditional Log MAP decoding algorithm is being done by using optimized scaling factors for both the decoders. The error correcting performance in presence of UEP in Additive White Gaussian Noise channel (AWGN) and Rayleigh fading are analyzed for the transmission of image with Discrete Cosine Transform (DCT) as source coding technique. This paper compares the performance of log MAP, Modified log MAP (MlogMAP) and Enhanced log MAP (ElogMAP) algorithms used for image transmission. The MlogMAP algorithm is found to be best for lower Eb/N0 values but for higher Eb/N0 ElogMAP performs better with optimized scaling factors. The performance comparison of AWGN with fading channel indicates the robustness of the proposed algorithm. According to the performance of three different message classes, class3 would be more protected than other two classes. From the performance analysis, it is observed that ElogMAP algorithm with UEP is best for transmission of an image compared to Log MAP and MlogMAP decoding algorithms.
Abstract: This study will examine how the therapeutic factors
(therapeutic catharsis-seeking and game-efficacy of the game player)
and self-construal factors (independent and interdependent
self-construal of the game player) as well as social capital factors
(bonding and bridging social capital of the game player) affect
aggression in the game. Results show that both therapeutic
catharsis-seeking and game self-efficacy are particularly important to
the players since they cause the game players’ aggressive tendencies to
be greatly diminished. Independent self-construal reduces the level of
the players’ aggression. Interestingly enough, the bonding social
capital enhances the level of the players’ aggression, while individuals
with bridging social capital did not show any significant effects. The
results and implications will be discussed herein.