Abstract: Calcium Phosphate Cement (CPC) due to its high bioactivity and optimum bioresorbability shows excellent bone regeneration capability. Despite it has limited applications as bone implant due to its macro-porous microstructure causing its poor mechanical strength. The reinforcement of apatitic CPCs with biocompatible fibre glass phase is an attractive area of research to improve upon its mechanical strength. Here, we study the setting behaviour of Si-doped and un-doped α tri calcium phosphate (α - TCP) based CPC and its reinforcement with addition of E-glass fibre. Alpha Tri calcium phosphate powders were prepared by solid state sintering of CaCO3 , CaHPO4 and Tetra Ethyl Ortho Silicate (TEOS) was used as silicon source to synthesize Si doped α-TCP powders. Both initial and final setting time of the developed cement was delayed because of Si addition. Crystalline phases of HA (JCPDS 9- 432), α-TCP (JCPDS 29-359) and β-TCP (JCPDS 9-169) were detected in the X-ray diffraction (XRD) pattern after immersion of CPC in simulated body fluid (SBF) for 0 hours to 10 days. As Si incorporation in the crystal lattice stabilized the TCP phase, Si doped CPC showed little slower rate of conversion into HA phase as compared to un-doped CPC. The SEM image of the microstructure of hardened CPC showed lower grain size of HA in un-doped CPC because of premature setting and faster hydrolysis of un-doped CPC in SBF as compared that in Si-doped CPC. Premature setting caused generation of micro and macro porosity in un-doped CPC structure which resulted in its lower mechanical strength as compared to that in Si-doped CPC. It was found that addition of 10 wt% of E-glass fibre into Si-doped α-TCP increased the average DTS of CPC from 8 MPa to 15 MPa as the fibres could resists the propagation of crack by deflecting the crack tip. Our study shows that biocompatible E-glass fibre in optimum proportion in CPC matrix can enhance the mechanical strength of CPC without affecting its biocompatibility.
Abstract: Temperature effect on the performance of a photovoltaic module is one of the main concerns that face this renewable energy, especially in hot arid region, e.g. United Arab Emirates. Overheating of the PV modules reduces the open circuit voltage and the efficiency of the modules dramatically. In this work, water-cooling is developed to enhance the performance of PV modules. Different scenarios are tested under UAE weather conditions: front, back and double cooling. A spraying system is used for the front cooling whether a direct contact water system is used for the back cooling. The experimental results are compared to non-cooling module and the performance of the PV module is determined for different situations. The experimental results show that the front cooling is more effective than the back cooling and may decrease the temperature of the PV module significantly.
Abstract: The Adaptive Line Enhancer (ALE) is widely used for
enhancing narrowband signals corrupted by broadband noise. In this
paper, we propose novel ALE methods to improve the enhancing
capability. The proposed methods are motivated by the fact that the
output of the ALE is a fine estimate of the desired narrowband signal
with the broadband noise component suppressed. The proposed
methods preprocess the input signal using ALE filter to regenerate a
finer input signal. Thus the proposed ALE is driven by the input signal
with higher signal-to-noise ratio (SNR). The analysis and simulation
results are presented to demonstrate that the proposed ALE has better
performance than conventional ALE’s.
Abstract: Salinity is one of the major factors limiting crop
production in an arid environment. Despite its global importance
soybean production suffer the problems of salinity stress causing
damages at plant development. So it is implacable to either search for
salinity enhancement of soybean plants. Therefore, in the current
study we try to clarify the mechanism that might be involved in the
ameliorating effects of osmo-protectants such as proline and glycine
betaine as well as, compost application on soybean plants grown
under salinity stress. The experiment was conducted under
greenhouse conditions at the Graduate School of Biosphere Science
Laboratory of Hiroshima University, Japan in 2011. The experiment
was designed as a spilt-split plot based on randomized complete
block design with four replications. The treatments could be
summarized as follows; (i) salinity concentrations (0 and 15 mM), (ii)
compost treatments (0 and 24 t ha-1) and (iii) the exogenous, proline
and glycine betaine concentrations (0 mM and 25 mM) for each.
Results indicated that salinity stress induced reduction in growth and
physiological aspects (dry weight per plant, chlorophyll content, N
and K+ content) of soybean plant compared with those of the
unstressed plants. On the other hand, salinity stress led to increases in
the electrolyte leakage ratio, Na and proline contents. Special
attention was paid to, the tolerance against salt stress was observed,
the improvement of salt tolerance resulted from proline, glycine
betaine and compost were accompanied with improved K+, and
proline accumulation. While, significantly decreased electrolyte
leakage ratio and Na+ content. These results clearly demonstrate that
harmful effect of salinity could reduce on growth aspects of soybean.
Consequently, exogenous osmoprotectants combine with compost
will effectively solve seasonal salinity stress problem and are a good
strategy to increase salinity resistance of soybean in the drylands.
Abstract: The effect of carbon nanofibers (CNFs) on the
electrical properties of Poly(vinylidene fluoride-hexafluoropropylene)
(P(VdF-HFP)) based gel polymer electrolytes has been investigated
in the present work. The length and diameter ranges of CNFs used in
the present work are 5-50 μm and 200-600 nm respectively. The
nanocomposite gel polymer electrolytes have been synthesized by
solution casting technique with varying CNFs content in terms of
weight percentage. Electrochemical impedance analysis demonstrates
that the reinforcement of carbon nanofibers significantly enhances the
ionic conductivity of the polymer electrolyte. The decrease of
crystallinity of P(VdF-HFP) due the addition of CNFs has been
confirmed by X-ray diffraction (XRD). The interaction of CNFs with
various constituents of nanocomposite gel polymer electrolytes has
been assessed by Fourier Transform Infrared (FTIR) spectroscopy.
Moreover CNFs added gel polymer electrolytes offer superior
thermal stability as compared to that of CNFs free electrolytes as
confirmed by Thermogravimetric analysis (TGA).
Abstract: One of the most important challenging factors in
medical images is nominated as noise. Image denoising refers to the
improvement of a digital medical image that has been infected by
Additive White Gaussian Noise (AWGN). The digital medical image
or video can be affected by different types of noises. They are
impulse noise, Poisson noise and AWGN. Computed tomography
(CT) images are subjects to low quality due to the noise. Quality of
CT images is dependent on absorbed dose to patients directly in such
a way that increase in absorbed radiation, consequently absorbed
dose to patients (ADP), enhances the CT images quality. In this
manner, noise reduction techniques on purpose of images quality
enhancement exposing no excess radiation to patients is one the
challenging problems for CT images processing. In this work, noise
reduction in CT images was performed using two different
directional 2 dimensional (2D) transformations; i.e., Curvelet and
Contourlet and Discrete Wavelet Transform (DWT) thresholding
methods of BayesShrink and AdaptShrink, compared to each other
and we proposed a new threshold in wavelet domain for not only
noise reduction but also edge retaining, consequently the proposed
method retains the modified coefficients significantly that result good
visual quality. Data evaluations were accomplished by using two
criterions; namely, peak signal to noise ratio (PSNR) and Structure
similarity (Ssim).
Abstract: In this paper, we study the optical nonlinearities of
Silver sulfide (Ag2S) nanostructures dispersed in the Dimethyl
sulfoxide (DMSO) under exposure to 532 nm, 15 nanosecond (ns)
pulsed laser irradiation. Ultraviolet–visible absorption spectrometry
(UV-Vis), X-ray diffraction (XRD), and transmission electron
microscopy (TEM) are used to characterize the obtained nanocrystal
samples. The band gap energy of colloid is determined by analyzing
the UV–Vis absorption spectra of the Ag2S NPs using the band
theory of semiconductors. Z-scan technique is used to characterize
the optical nonlinear properties of the Ag2S nanoparticles (NPs).
Large enhancement of two photon absorption effect is observed with
increase in concentration of the Ag2S nanoparticles using open Zscan
measurements in the ns laser regime. The values of the nonlinear
absorption coefficients are determined based on the local nonlinear
responses including two photon absorption. The observed aperture
dependence of the Ag2S NP limiting performance indicates that the
nonlinear scattering plays an important role in the limiting action of
the sample. The concentration dependence of the optical liming is
also investigated. Our results demonstrate that the optical limiting
threshold decreases with increasing the silver sulfide NPs in DMSO.
Abstract: Nowadays, energy dissipation devices are commonly
used in structures. High rate of energy absorption during earthquakes
is the benefit of using such devices, which results in damage
reduction of structural elements, specifically columns. The hysteretic
damping capacity of energy dissipation devices is the key point that it
may adversely make analysis and design process complicated. This
effect may be generally represented by Equivalent Viscous Damping
(EVD). The equivalent viscous damping might be obtained from the
expected hysteretic behavior regarding to the design or maximum
considered displacement of a structure. In this paper, the hysteretic
damping coefficient of a steel Moment Resisting Frame (MRF),
which its performance is enhanced by a Buckling Restrained Brace
(BRB) system has been evaluated. Having foresight of damping
fraction between BRB and MRF is inevitable for seismic design
procedures like Direct Displacement-Based Design (DDBD) method.
This paper presents an approach to calculate the damping fraction for
such systems by carrying out the dynamic nonlinear time history
analysis (NTHA) under harmonic loading, which is tuned to the
natural system frequency. Two MRF structures, one equipped with
BRB and the other without BRB are simultaneously studied.
Extensive analysis shows that proportion of each system damping
fraction may be calculated by its shear story portion. In this way,
contribution of each BRB in the floors and their general contribution
in the structural performance may be clearly recognized, in advance.
Abstract: Anammox is a novel and promising technology that has changed the traditional concept of biological nitrogen removal. The process facilitates direct oxidation of ammonical nitrogen under anaerobic conditions with nitrite as an electron acceptor without addition of external carbon sources. The present study investigated the feasibility of Anammox Hybrid Reactor (AHR) combining the dual advantages of suspended and attached growth media for biodegradation of ammonical nitrogen in wastewater. Experimental unit consisted of 4 nos. of 5L capacity AHR inoculated with mixed seed culture containing anoxic and activated sludge (1:1). The process was established by feeding the reactors with synthetic wastewater containing NH4-H and NO2-N in the ratio 1:1 at HRT (hydraulic retention time) of 1 day. The reactors were gradually acclimated to higher ammonium concentration till it attained pseudo steady state removal at a total nitrogen concentration of 1200 mg/l. During this period, the performance of the AHR was monitored at twelve different HRTs varying from 0.25-3.0 d with increasing NLR from 0.4 to 4.8 kg N/m3d. AHR demonstrated significantly higher nitrogen removal (95.1%) at optimal HRT of 1 day. Filter media in AHR contributed an additional 27.2% ammonium removal in addition to 72% reduction in the sludge washout rate. This may be attributed to the functional mechanism of filter media which acts as a mechanical sieve and reduces the sludge washout rate many folds. This enhances the biomass retention capacity of the reactor by 25%, which is the key parameter for successful operation of high rate bioreactors. The effluent nitrate concentration, which is one of the bottlenecks of anammox process was also minimised significantly (42.3-52.3 mg/L). Process kinetics was evaluated using first order and Grau-second order models. The first-order substrate removal rate constant was found as 13.0 d-1. Model validation revealed that Grau second order model was more precise and predicted effluent nitrogen concentration with least error (1.84±10%). A new mathematical model based on mass balance was developed to predict N2 gas in AHR. The mass balance model derived from total nitrogen dictated significantly higher correlation (R2=0.986) and predicted N2 gas with least error of precision (0.12±8.49%). SEM study of biomass indicated the presence of heterogeneous population of cocci and rod shaped bacteria of average diameter varying from 1.2-1.5 mm. Owing to enhanced NRE coupled with meagre production of effluent nitrate and its ability to retain high biomass, AHR proved to be the most competitive reactor configuration for dealing with nitrogen laden wastewater.
Abstract: This paper describes the collection and analysis of
data obtained from face-to-face interviews conducted in selected
Libyan industrial companies. The objectives of the interviews are to
enhance understanding, and generate explanations of current issues in
culture and quality management systems in Libyan companies. The
method used in analyzing the questions, as well as the main finding
of each question are explained. The interviews probed areas identify
national and organizational culture, quality management systems,
current methods, effects, barriers and other factors affecting the
success of quality management implementation. Eleven questions are
prepared and been discussed with the interviewees.
Abstract: Laban Movement Analysis (LMA), developed in the
dance community over the past seventy years, is an effective method
for observing, describing, notating, and interpreting human
movement to enhance communication and expression in everyday
and professional life. Many applications that use motion capture data
might be significantly leveraged if the Laban qualities will be
recognized automatically. This paper presents an automated
recognition method of Laban qualities from motion capture skeletal
recordings and it is demonstrated on the output of Microsoft’s Kinect
V2 sensor.
Abstract: Multiple-input multiple-output (MIMO) radar has
received increasing attention in recent years. MIMO radar has many
advantages over conventional phased array radar such as target
detection,resolution enhancement, and interference suppression. In
this paper, the results are presented from a simulation study of MIMO
uniformly-spaced linear array (ULA) antennas. The performance is
investigated under varied parameters, including varied array size,
pseudo random (PN) sequence length, number of snapshots, and
signal to noise ratio (SNR). The results of MIMO are compared to a
traditional array antenna.
Abstract: Mobile Ad Hoc Networks (MANETs) is a collection
of mobile devices forming a communication network without
infrastructure. MANET is vulnerable to security threats due to
network’s limited security, dynamic topology, scalability and the lack
of central management. The Quality of Service (QoS) routing in such
networks is limited by network breakage caused by node mobility or
nodes energy depletions. The impact of node mobility on trust
establishment is considered and its use to propagate trust through a
network is investigated in this paper. This work proposes an
enhanced Associativity Based Routing (ABR) with Fuzzy based
Trust (Fuzzy- ABR) routing protocol for MANET to improve QoS
and to mitigate network attacks.
Abstract: The increasing volume of solid waste generated,
collected and disposed daily complicate adequate management of
solid waste by relevant agency like Niger State Environmental
Protection Agency (NISEPA). In addition, the impacts of solid waste
on the natural environment and human livelihood require
identification of cost-effective ways for sustainable municipal waste
management in Nigeria. These signal the need for identifying
environment-friendly initiative and local solution to address the
problem of municipal solid waste. A research field was secured at
Pago, Minna, Niger State which is located in the guinea savanna belt
of Nigeria, within longitude 60 361 4311 - 4511 and latitude 90 291
37.6111 - .6211 N. Poultry droppings, decomposed household waste
manure and NPK treatments were used. The experimental field was
divided into three replications and four (4) treatments on each
replication making a total of twelve (12) plots. The treatments were
allotted using Randomized Complete Block Design (RCBD) and
Data collected was analyzed using SPSS software and RCBD. The
result depicts variation in plant height and number of leaves at 50%
flowering; Poultry dropping records the highest height while the
number of leaves for waste manure competes fairly well with NPK
treatment. Similarly, the varying treatments significantly increase
vegetable yield, as the control (non-treatment) records the least yield
for the three vegetable samples. Adoption of this organic manure for
cultivation does not only enhance environment quality and attainment
of food security but will contribute to local economic development,
poverty alleviation as well as social inclusion.
Abstract: A new design of aerostatic thrust bearing is proposed
for high static stiffness. The bearing body, which is mead of polymer
covered with metallic membrane, is held by a circular ring. Such a
support helps form a concave air gap to grasp the air pressure. The
polymer body, which can be made rapidly by either injection or
molding is able to provide extra damping under dynamic loading. The
smooth membrane not only serves as the bearing surface but also
protects the polymer body. The restrictor is a capillary inside a silicone
tube. It can passively compensate the variation of load by expanding
the capillary diameter for more air flux. In the present example, the
stiffness soars from 15.85 N/μm of typical bearing to 349.85 N/μm at
bearing elevation 9.5 μm; meanwhile the load capacity also enhances
from 346.86 N to 704.18 N.
Abstract: Financial innovations can be regarded as the cause
and the effect of the evolution of the financial system. Most of
financial innovations are created by various financial institutions for
their own purposes and needs. However, due to their diversity,
financial innovations can be also applied by various business entities
(other than financial institutions).
This paper focuses on the potential application of financial
innovations by non-financial companies. It is assumed that financial
innovations may be effectively applied in all fields of corporate
financial decisions integrating financial management with the risk
management process. Appropriate application of financial
innovations may enhance the development of the company and
increase its value by improving its financial situation and reducing
the level of risk. On the other hand, misused financial innovations
may become the source of extra risk for the company threatening its
further operation.
The main objective of the paper is to identify the major types of
financial innovations offered to non-financial companies by the
banking system in Poland. It also aims at identifying the main factors
determining the creation of financial innovations in the banking
system in Poland and indicating future directions of their
development.
This paper consists of conceptual and empirical part. Conceptual
part based on theoretical study is focused on the determinants of the
process of financial innovations and their application by the nonfinancial
companies. Theoretical study is followed by the empirical
research based on the analysis of the actual offer of the 20 biggest
banks operating in Poland with regard to financial innovations
offered to SMEs and large corporations. These innovations are
classified according to the main functions of the integrated financial
management, such as financing, investment, working capital
management and risk management.
Empirical study has proved that the biggest banks operating in the
Polish market offer to their business customers many types and
classes of financial innovations. This offer appears vast and adequate
to the needs and purposes of the Polish non-financial companies. It
was observed that financial innovations pertained to financing
decisions dominate in the banks’ offer. However, due to high
diversification of the offered financial innovations, business
customers may effectively apply them in all fields and areas of
integrated financial management. It should be underlined, that the
banks’ offer is highly dispersed, which may limit the implementation
of financial innovations in the corporate finance. It would be also
recommended for the banks operating in the Polish market to
intensify the education campaign aiming at increasing knowledge
about financial innovations among business customers.
Abstract: This research paper presents the current practices of
teacher professional development, perceived as beneficial by teachers
themselves, in a private secondary school in Brunei Darussalam. This
is part of the findings of a larger qualitative study on teacher
empowerment, using ethnographic methods for data collection, i.e.
participant observation, interviews and document analysis. The field
work was carried out over a period of six months in 2013. An
analysis of the field data revealed multiple pathways of teacher
professional development existing in the school. The results indicate
that school leaders, the teacher community in the school, students,
and the teachers themselves were the agents in a school that
facilitated teacher empowerment. Besides contributing to the
knowledge base on teacher professional development, the results of
this study provide directions for educational policy makers in their
efforts to enhance professional development in secondary schools of
similar characteristics. For school leaders and the teacher community,
these findings offer guidelines for maximizing the opportunities for
these professional development practices, by strengthening
collegiality and by using the existing structures optimally for the
benefit of all concerned.
Abstract: By enhancing the applicatıon of grounds for
establishment and due to the lack of appropriate sites, engineers
attempt to seek out a new method to reduce the weakness of soils. İn
aspect of economic situation, various ways have been used to
decrease the weak grounds. Because of the rapid development of
infrastructural facilities, spreading the construction operation is an
obligation. Furthermore, in various sites with the really bad soil
situation, engineers have considered obvious problems. One of the
most essential ways for developing the weak soils is stone column.
Obviously, the method was introduced in France in 1830 to improve
a native soil initially. Stone columns have an expanding range of
usage in different rough foundation sites all over the world to
increase the bearing capacity, to reduce the whole and differential
settlements, to enhance the rate of consolidation, to stabilize slopes
stability of embankments and to increase the liquefaction resistance
as well. A recent procedure called installing vertical nails along the
round stone columns in order to make better the performance of
considered columns is offered. Moreover, thanks to the enhancing the
nail diameter, number and embedment nail depth, the positive points
of vertical circumferential nails increases. Based on the result of this
study, load caring capacity will be develop with enhancing the length
and the power of reinforcements in vertical encasement stone column
(CESC). In this study, the main purpose is comparing two methods of
stone columns (installed a nail surrounding the stone columns and
using geogrid on clay) for enhancing the bearing capacity, decreasing
the whole and various settlements.
Abstract: An investigation has been presented to analyze the
effect of internal heat source on the onset of Hadley-Prats flow in
a horizontal fluid saturated porous medium. We examine a better
understanding of the combined influence of the heat source and mass
flow effect by using linear stability analysis. The resultant eigenvalue
problem is solved by using shooting and Runga-Kutta methods for
evaluate critical thermal Rayleigh number with respect to various
flow governing parameters. It is identified that the flow is switch from
stabilizing to destabilizing as the horizontal thermal Rayleigh number
is enhanced. The heat source and mass flow increases resulting a
stronger destabilizing effect.
Abstract: In this paper, we present a new segmentation approach
for focal liver lesions in contrast enhanced ultrasound imaging. This
approach, based on a two-cluster Fuzzy C-Means methodology,
considers type-II fuzzy sets to handle uncertainty due to the image
modality (presence of speckle noise, low contrast, etc.), and to
calculate the optimum inter-cluster threshold. Fine boundaries are
detected by a local recursive merging of ambiguous pixels. The
method has been tested on a representative database. Compared to
both Otsu and type-I Fuzzy C-Means techniques, the proposed
method significantly reduces the segmentation errors.