Abstract: The energy consumption and delay in read/write
operation of conventional SRAM is investigated analytically as well
as by simulation. Explicit analytical expressions for the energy
consumption and delay in read and write operation as a function of
device parameters and supply voltage are derived. The expressions are
useful in predicting the effect of parameter changes on the energy
consumption and speed as well as in optimizing the design of
conventional SRAM. HSPICE simulation in standard 0.25μm CMOS
technology confirms precision of analytical expressions derived from
this paper.
Abstract: This research investigates the suitability of fuel oil in
improving gypseous soil. A detailed laboratory tests were carried-out
on two soils (soil I with 51.6% gypsum content, and soil II with
26.55%), where the two soils were obtained from Al-Therthar site
(Al-Anbar Province-Iraq).
This study examines the improvement of soil properties using the
gypsum material which is locally available with low cost to minimize
the effect of moisture on these soils by using the fuel oil. This study
was conducted on two models of the soil gypsum, from the Tharthar
area. The first model was sandy soil with Gypsum content of (51.6%)
and the second is clayey soil and the content of Gypsum is (26.55%).
The program included tests measuring the permeability and
compressibility of the soil and their collapse properties. The shear
strength of the soil and the amounts of weight loss of fuel oil due to
drying had been found. These tests have been conducted on the
treated and untreated soils to observe the effect of soil treatment on
the engineering properties when mixed with varying degrees of fuel
oil with the equivalent of the water content.
The results showed that fuel oil is a good material to modify the
basic properties of the gypseous soil of collapsibility and
permeability, which are the main problems of this soil and retained
the soil by an appropriate amount of the cohesion suitable for
carrying the loads from the structure.
Abstract: Excilamps are new UV sources with great potential
for application in wastewater treatment. In the present work, a XeBr
excilamp emitting radiation at 283 nm has been used for the
photodegradation of 4-chlorophenol within a range of concentrations
from 50 to 500 mg L-1. Total removal of 4-chlorophenol was
achieved for all concentrations assayed. The two main photoproduct
intermediates formed along the photodegradation process,
benzoquinone and hydroquinone, although not being completely
removed, remain at very low residual concentrations. Such
concentrations are insignificant compared to the 4-chlorophenol
initial ones and non-toxic. In order to simulate the process and scaleup,
a kinetic model has been developed and validated from the
experimental data.
Abstract: This paper analyzes the extent to which the justices of
the U.S. Supreme Court cast votes that support the positions of the
president, or more generally the Executive Branch. Can presidents
count on such deference from those justices they nominate or those
whom are nominated by other presidents of the same party? Or, do
the justices demonstrate judicial independence and impartiality such
that they are not so predisposed to vote in favor of arguments of their
nominating president-s party? The results suggest that while in
general the justices do not exhibit any marked tendency to partisan
support of presidents, more recent and conservative Supreme Court
justices are significantly more likely to support Republican
presidents.
Abstract: In the present work, we propose a new projection method for solving the matrix equation AXB = F. For implementing our new method, generalized forms of block Krylov subspace and global Arnoldi process are presented. The new method can be considered as an extended form of the well-known global generalized minimum residual (Gl-GMRES) method for solving multiple linear systems and it will be called as the extended Gl-GMRES (EGl- GMRES). Some new theoretical results have been established for proposed method by employing Schur complement. Finally, some numerical results are given to illustrate the efficiency of our new method.
Abstract: Virtual Assembly (VA) is one of the key technologies
in advanced manufacturing field. It is a promising application of
virtual reality in design and manufacturing field. It has drawn much
interest from industries and research institutes in the last two decades.
This paper describes a process for integrating an interactive Virtual
Reality-based assembly simulation of a digital mockup with the
CAD/CAM infrastructure. The necessary hardware and software
preconditions for the process are explained so that it can easily be
adopted by non VR experts. The article outlines how assembly
simulation can improve the CAD/CAM procedures and structures;
how CAD model preparations have to be carried out and which
virtual environment requirements have to be fulfilled. The issue of
data transfer is also explained in the paper. The other challenges and
requirements like anti-aliasing and collision detection have also been
explained. Finally, a VA simulation has been carried out for a ball
valve assembly and a car door assembly with the help of Vizard
virtual reality toolkit in a semi-immersive environment and their
performance analysis has been done on different workstations to
evaluate the importance of graphical processing unit (GPU) in the
field of VA.
Abstract: Modern times call organizations to have an active role
in the social arena, through Corporate Social Responsibility (CSR).
The objective of this research was to test the hypothesis that there is a
positive relation between social performance and economic
performance, and if there is a positive correlation between social
performance and financial-economic performance. To test these
theories a measure of social performance, based on the Green Book
of Commission of the European Community, was used in a group of
nineteen Portuguese top companies, listed on the PSI 20 index,
through a period of five years, since 2005 to 2009. A clusters
analysis was applied to group companies by their social performance
and to compare and correlate their economic performance. Results
indicate that companies that had a better social performance are not
the ones who had a better economic performance, and suggest that
the middle path might provide a good relation CSR-Economic
performance, as a basis to a sustainable development.
Abstract: This paper presents an optimal design of linear phase
digital high pass finite impulse response (FIR) filter using Improved
Particle Swarm Optimization (IPSO). In the design process, the filter
length, pass band and stop band frequencies, feasible pass band and
stop band ripple sizes are specified. FIR filter design is a multi-modal
optimization problem. An iterative method is introduced to find the
optimal solution of FIR filter design problem. Evolutionary
algorithms like real code genetic algorithm (RGA), particle swarm
optimization (PSO), improved particle swarm optimization (IPSO)
have been used in this work for the design of linear phase high pass
FIR filter. IPSO is an improved PSO that proposes a new definition
for the velocity vector and swarm updating and hence the solution
quality is improved. A comparison of simulation results reveals the
optimization efficacy of the algorithm over the prevailing
optimization techniques for the solution of the multimodal, nondifferentiable,
highly non-linear, and constrained FIR filter design
problems.
Abstract: As known, the guard wires of overhead high voltage
are usually grounded through the grounding systems of support and
of the terminal stations. They do affect the zero sequence impedance
value of the line, Z0, which is generally, calculated assuming that the
wires guard are at ground potential. In this way it is not considered
the effect of the resistances of earth of supports and stations. In this
work is formed a formula for the calculation of Z0 which takes
account of said resistances. Is also proposed a method of calculating
the impedance zero sequence overhead lines in which, in various
sections or spans, the guard wires are connected to the supports, or
isolated from them, or are absent. Parametric analysis is given for
lines 220 kV and 400 kV, which shows the extent of the errors made
with traditional methods of calculation.
Abstract: Modeling of a manufacturing system enables one to
identify the effects of key design parameters on the system performance and as a result to make correct decision. This paper
proposes a manufacturing system modeling approach using a spreadsheet model based on queuing network theory, in which a
static capacity planning model and stochastic queuing model are integrated. The model was used to improve the existing system utilization in relation to product design. The model incorporates few
parameters such as utilization, cycle time, throughput, and batch size.
The study also showed that the validity of developed model is good enough to apply and the maximum value of relative error is 10%, far
below the limit value 32%. Therefore, the model developed in this
study is a valuable alternative model in evaluating a manufacturing system
Abstract: We succeeded to produce a high performance and flexible graphene/Manganese dioxide (G/MnO2) electrode coated on flexible polyethylene terephthalate (PET) substrate. The graphene film is initially synthesized by drop-casting the graphene oxide (GO) solution on the PET substrate, followed by simultaneous reduction and patterning of the dried film using carbon dioxide (CO2) laser beam with power of 1.8 W. Potentiostatic Anodic Deposition method was used to deposit thin film of MnO2 with different loading mass 10 – 50 and 100 μg.cm-2 on the pre-prepared graphene film. The electrodes were fully characterized in terms of structure, morphology, and electrochemical performance. A maximum specific capacitance of 973 F.g-1 was attributed when depositing 50μg.cm-2 MnO2 on the laser reduced graphene oxide rGO (or G/50MnO2) and over 92% of its initial capacitance was retained after 1000 cycles. The good electrochemical performance and long-term cycling stability make our proposed approach a promising candidate in the supercapacitor applications.
Abstract: In this paper, we analyze the effect of noise in a single- ended input differential amplifier working at high frequencies. Both extrinsic and intrinsic noise are analyzed using time domain method employing techniques from stochastic calculus. Stochastic differential equations are used to obtain autocorrelation functions of the output noise voltage and other solution statistics like mean and variance. The analysis leads to important design implications and suggests changes in the device parameters for improved noise characteristics of the differential amplifier.
Abstract: Long number multiplications (n ≥ 128-bit) are a
primitive in most cryptosystems. They can be performed better by
using Karatsuba-Ofman technique. This algorithm is easy to
parallelize on workstation network and on distributed memory, and
it-s known as the practical method of choice. Multiplying long
numbers using Karatsuba-Ofman algorithm is fast but is highly
recursive. In this paper, we propose different designs of
implementing Karatsuba-Ofman multiplier. A mixture of sequential
and combinational system design techniques involving pipelining is
applied to our proposed designs. Multiplying large numbers can be
adapted flexibly to time, area and power criteria. Computationally
and occupation constrained in embedded systems such as: smart
cards, mobile phones..., multiplication of finite field elements can be
achieved more efficiently. The proposed designs are compared to
other existing techniques. Mathematical models (Area (n), Delay (n))
of our proposed designs are also elaborated and evaluated on
different FPGAs devices.
Abstract: The economical criterion is accounted as the objective
function to develop a computer program for designing lightning
protection systems for substations by using masts and Matlab in this
work. Masts are needed to be placed at desired locations; the program
will then show mast heights whose sum is the smallest, i.e. satisfies
the economical criterion. The program is helpful for engineers to
quickly design a lightning protection system for a substation. To
realize this work, methodology and limited conditions of the program,
as well as an example of the program result, were described in this
paper.
Abstract: Grey mold on grape is caused by the fungus Botrytis
cinerea Pers. Trichodex WP, a new biofungicide, that contains fungal
spores of Trichoderma harzianum Rifai, was used for biological
control of Grey mold on grape. The efficacy of Trichodex WP has
been reported from many experiments. Experiments were carried out
in the locality – Banatski Karlovac, on grapevine species – talijanski
rizling. The trials were set according to instructions of methods
PP1/152(2) and PP1/17(3) , according to a fully randomized block
design. Phytotoxicity was estimated by PP methods 1/135(2), the
intensity of infection according to Towsend Heuberger , the
efficiency by Abbott, the analysis of variance with Duncan test and
PP/181(2). Application of Trichodex WP is limited to the first two
treatments. Other treatments are performed with the fungicides based
on a.i. procymidone, vinclozoline and iprodione.
Abstract: The customer satisfaction for textile sector carries
great importance like the customer satisfaction for other sectors
carry. Especially, if it is considered that gaining new customers
create four times more costs than protecting existing customers from
leaving, it can be seen that the customer satisfaction plays a great
role for the firms. In this study the affecting independent variables of
customer satisfaction are chosen as brand image, perceived service
quality and perceived product quality. By these independent
variables, it is investigated that if any differences exist in perception
of customer satisfaction according to the Turkish textile consumers in
the view of gender. In data analysis of this research the SPSS
program is used.
Abstract: The essentiality of maintenance assessment and
maintenance optimization in design stage is analyzed, and the existent
problems of conventional maintenance design method are illuminated.
MDMVM (Maintenance Design Method based Virtual Maintenance)
is illuminated, and the process of MDMVM established, and the
MDMVM architecture is given out. The key techniques of MDMVM
are analyzed, and include maintenance design based KBE (Knowledge
Based Engineering) and virtual maintenance based physically
attribute. According to physical property, physically based modeling,
visual object movement control, the simulation of operation force and
maintenance sequence planning method are emphatically illuminated.
Maintenance design system based virtual maintenance is established in
foundation of maintenance design method.
Abstract: The inherent complexity in nowadays- business
environments is forcing organizations to be attentive to the dynamics
in several fronts. Therefore, the management of technological
innovation is continually faced with uncertainty about the future.
These issues lead to a need for a systemic perspective, able to analyze
the consequences of interactions between different factors. The field
of technology foresight has proposed methods and tools to deal with
this broader perspective. In an attempt to provide a method to analyze
the complex interactions between events in several areas, departing
from the identification of the most strategic competencies, this paper
presents a methodology based on the Delphi method and Quality
Function Deployment. This methodology is applied in a sheet metal
processing equipment manufacturer, as a case study.
Abstract: This study proposes a novel recommender system to
provide the advertisements of context-aware services. Our proposed
model is designed to apply a modified collaborative filtering (CF)
algorithm with regard to the several dimensions for the personalization
of mobile devices – location, time and the user-s needs type. In
particular, we employ a classification rule to understand user-s needs
type using a decision tree algorithm. In addition, we collect primary
data from the mobile phone users and apply them to the proposed
model to validate its effectiveness. Experimental results show that the
proposed system makes more accurate and satisfactory advertisements
than comparative systems.
Abstract: Service quality has become a centerpiece for airline companies in vying with one another and keeps their image in the minds of passengers. Many airlines have pushed service quality through service personalization which includes both ground and on board especially from the viewpoint of retaining satisfied passengers and attracting new ones. Besides those, in-flight meals/food service is another important aspect of the airline operation. The in flight meals/food services now are seen as part of marketing strategies in attracting business or leisure travelers. This study reports the outcomes of the investigation on in-flight meals/food attributes toward passengers- level of satisfaction and re-flying intention. Taste, freshness, appearance of in-flight meals/food served and menu choices are important to the airlines passengers especially for the long haul flight. Food not only contributes to the prediction of the airline passengers- levels of satisfaction but besides other factors slightly influence passengers- re- flying intention. Airline companies therefore should not ignore this element but take the opportunity to create more attractive and acceptable in-flight meals/food along with other matter as marketing tools in attracting passengers to re-flying with them.