Abstract: Electrochemical-oxidation of Reactive Black-5 (RB- 5) was conducted for degradation using DSA type Ti/RuO2-SnO2- Sb2O5 electrode. In the study, for electro-oxidation, electrode was indigenously fabricated in laboratory using titanium as substrate. This substrate was coated using different metal oxides RuO2, Sb2O5 and SnO2 by thermal decomposition method. Laboratory scale batch reactor was used for degradation and decolorization studies at pH 2, 7 and 11. Current density (50mA/cm2) and distance between electrodes (8mm) were kept constant for all experiments. Under identical conditions, removal of color, COD and TOC at initial pH 2 was 99.40%, 55% and 37% respectively for initial concentration of 100 mg/L RB-5. Surface morphology and composition of the fabricated electrode coatings were characterized using scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX) respectively. Coating microstructure was analyzed by X-ray diffraction (XRD). Results of this study further revealed that almost 90% of oxidation occurred within 5-10 minutes.
Abstract: This paper presents an overview of current municipal
solid waste management in Khoram Abad city.
According to data collected by the local authorities, the waste
generation rate is estimated to be 800 g/cap.d with density of 243
kg/m3. Solid waste is stored in different types of containers at the
source of generation in different areas of the city.
Local Authority is responsible for waste collection, transportation.
Municipality is responsible for waste collection, using private sector
contracts.
At present, both mechanical and manual methods are used to
collect residential waste. Manual methods of collection are the most
commonly used for waste collection in most parts of the city.
Land filling is the main disposal method in this city. But it has
some obvious problem and deficiencies
The current state of solid waste management has been improved
slightly in the last decade. By more actions can reduce the human and
environmental risks.
Abstract: IEEE 802.15.4a impulse radio-time hopping ultra wide
band (IR-TH UWB) physical layer, due to small duty cycle and very
short pulse widths is robust against multipath propagation. However,
scattering and reflections with the large number of obstacles in indoor
channel environments, give rise to dense multipath fading. It imposes
serious problem to optimum Rake receiver architectures, for which
very large number of fingers are needed. Presence of strong noise
also affects the reception of fine pulses having extremely low power
spectral density. A robust SRake receiver for IEEE 802.15.4a IRTH
UWB in dense multipath and additive white Gaussian noise
(AWGN) is proposed to efficiently recover the weak signals with
much reduced complexity. It adaptively increases the signal to noise
(SNR) by decreasing noise through a recursive least square (RLS)
algorithm. For simulation, dense multipath environment of IEEE
802.15.4a industrial non line of sight (NLOS) is employed. The power
delay profile (PDF) and the cumulative distribution function (CDF)
for the respective channel environment are found. Moreover, the error
performance of the proposed architecture is evaluated in comparison
with conventional SRake and AWGN correlation receivers. The
simulation results indicate a substantial performance improvement
with very less number of Rake fingers.
Abstract: In manufacturing industries, development of measurement leads to increase the number of monitoring variables and eventually the importance of multivariate control comes to the fore. Statistical process control (SPC) is one of the most widely used as multivariate control chart. Nevertheless, SPC is restricted to apply in processes because its assumption of data as following specific distribution. Unfortunately, process data are composed by the mixture of several processes and it is hard to estimate as one certain distribution. To alternative conventional SPC, therefore, nonparametric control chart come into the picture because of the strength of nonparametric control chart, the absence of parameter estimation. SVDD based control chart is one of the nonparametric control charts having the advantage of flexible control boundary. However,basic concept of SVDD has been an oversight to the important of data characteristic, density distribution. Therefore, we proposed DW-SVDD (Density Weighted SVDD) to cover up the weakness of conventional SVDD. DW-SVDD makes a new attempt to consider dense of data as introducing the notion of density Weight. We extend as control chart using new proposed SVDD and a simulation study of various distributional data is conducted to demonstrate the improvement of performance.
Abstract: Mobile WiMAX is a broadband wireless solution that
enables convergence of mobile and fixed broadband networks
through a common wide area broadband radio access technology and
flexible network architecture. It adopts Orthogonal Frequency
Division Multiple Access (OFDMA) for improved multi-path
performance in Non-Line-Of-Sight (NLOS) environments. Scalable
OFDMA (SOFDMA) is introduced in the IEEE 802e[1]. WIMAX
system uses one of different types of channel coding but The
mandatory channel coding scheme is based on binary nonrecursive
Convolutional Coding (CC). There are other several optional channel
coding schemes such as block turbo codes, convolutional turbo
codes, and low density parity check (LDPC).
In this paper a comparison between the performance of WIMAX
using turbo code and using convolutional product code (CPC) [2] is
made. Also a combination between them had been done. The CPC
gives good results at different SNR values compared to both the
turbo system, and the combination between them. For example, at
BER equal to 10-2 for 128 subcarriers, the amount of improvement
in SNR equals approximately 3 dB higher than turbo code and equals
approximately 2dB higher than the combination respectively. Several
results are obtained at different modulating schemes (16QAM and
64QAM) and different numbers of sub-carriers (128 and 512).
Abstract: Silk sericin (SS) is a glue-like protein from silkworm
cocoon. With its outstanding moisturization and activation collagen
synthesis properties, silk protein is applied for wound healing. Since
wound dressing in film preparation can facilitate patients-
convenience and reduce risk of wound contraction, SS and polyvinyl
alcohol (PVA) films were prepared with various concentrations of
SS. Their physical properties such as surface density, light
transmission, protein dissolution and tensile modulus were
investigated. The results presented that 3% SS with 2% PVA is the
best ingredient for SS film forming.
Abstract: The influence of extrusion parameters on surface
quality and properties of AA6061+x% vol. SiC (x = 0; 2,5; 5; 7,5;10)
composites was discussed in this paper. The averages size of
AA6061 and SiC particles were 10.6 μm and 0.42 μm, respectively.
Two series of composites (I - compacts were preheated at extrusion
temperature through 0.5 h and cooled by water directly after process;
II - compacts were preheated through 3 hours and were not cooled)
were consolidated via powder metallurgy processing and extruded by
KoBo method. High values of density for both series of composites
were achieved. Better surface quality was observed for II series of
composites. Moreover, for these composites lower (compared to I
series) but more uniform strength properties over the cross-section of
the bar were noticed. Microstructure and Young-s modulus
investigations were made.
Abstract: The response of growth and yield of rainfed-chickpea
to population density should be evaluated based on long-term
experiments to include the climate variability. This is achievable just
by simulation. In this simulation study, this evaluation was done by
running the CYRUS model for long-term daily weather data of five
locations in Iran. The tested population densities were 7 to 59 (with
interval of 2) stands per square meter. Various functions, including
quadratic, segmented, beta, broken linear, and dent-like functions,
were tested. Considering root mean square of deviations and linear
regression statistics [intercept (a), slope (b), and correlation
coefficient (r)] for predicted versus observed variables, the quadratic
and broken linear functions appeared to be appropriate for describing
the changes in biomass and grain yield, and in harvest index,
respectively. Results indicated that in all locations, grain yield tends
to show increasing trend with crowding the population, but
subsequently decreases. This was also true for biomass in five
locations. The harvest index appeared to have plateau state across
low population densities, but decreasing trend with more increasing
density. The turning point (optimum population density) for grain
yield was 30.68 stands per square meter in Isfahan, 30.54 in Shiraz,
31.47 in Kermanshah, 34.85 in Tabriz, and 32.00 in Mashhad. The
optimum population density for biomass ranged from 24.6 (in
Tabriz) to 35.3 stands per square meter (Mashhad). For harvest index
it varied between 35.87 and 40.12 stands per square meter.
Abstract: Polyurethane foams (PUF) were formed by a chemical
reaction of polyol and isocyanate. The polyol was manufactured by
ring-opening hydrolysis of epoxidized soybean oil in the presence of
phosphoric acid under varying experimental conditions. Other
factors in the foam formulation such as water content and surfactant
were kept constant. The effect of the amount of solvents, phosphoric
acid, and their derivates in the foam formulation on the properties of
polyurethane foams were studied. The properties of the material were
measured via a number of parameters, which are water content of
prepared polyol, polymer density and cellular structures.
Abstract: The breakdown strength characteristic of Low Density
Polyethylene films (LDPE) under DC voltage application and the
effect of water absorption have been studied. Mainly, our experiment
was investigated under two conditions; dry and heavy water
absorption. Under DC ramp voltage, the result found that the
breakdown strength under heavy water absorption has a lower value
than dry condition. In order to clarify the effect, the temperature rise of
film was observed using non contact thermograph until the occurrence
of the electrical breakdown and the conduction current of the sample
was also measured in correlation with the thermograph measurement.
From the observations, it was shown that under the heavy water
absorption, the hot spot in the samples appeared at lower voltage. At
the same voltage the temperature of the hot spot and conduction
current was higher than that under the dry condition. The measurement
result has a good correlation between the existence of a critical field
for conduction current and thermograph observation. In case of the
heavy water absorption, the occurrence of the threshold field was
earlier than the dry condition as result lead to higher of conduction
current and the temperature rise appears after threshold field was
significantly increased in increasing of field. The higher temperature
rise was caused by the higher current conduction as the result the
insulation leads to breakdown to the lower field application.
Abstract: The forest stand consisted of four layers. The species
composition between the third and the bottom layers was almost
similar, whereas it was almost exclusive between the top and the lower
three layers. The values of Shannon-s index H' and Pielou-s index
J ' tended to increase from the bottom layer upward, except for
H' -value of the top layer. The values of H' and J ' were 4.21 bit
and 0.73, respectively, for the total stand. High woody species
diversity of the forest depended on large trees in the upper layers,
which trend was different from a subtropical evergreen broadleaf
forest grown in silicate habitat in the northern part of Okinawa Island.
The spatial distribution of trees was overlapped between the third and
the bottom layers, whereas it was independent or slightly exclusive
between the top and the lower three layers. Mean tree weight of each
layer decreased from the top toward the bottom layer, whereas the
corresponding tree density increased from the top downward. This
relationship was analogous to the process of self-thinning plant
populations.
Abstract: In this paper we study the transformation of Euler equations 1 , u u u Pf t (ρ ∂) + ⋅∇ = − ∇ + ∂ G G G G ∇⋅ = u 0, G where (ux, t) G G is the velocity of a fluid, P(x, t) G is the pressure of a fluid andρ (x, t) G is density. First of all, we rewrite the Euler equations in terms of new unknown functions. Then, we introduce new independent variables and transform it to a new curvilinear coordinate system. We obtain the Euler equations in the new dependent and independent variables. The governing equations into two subsystems, one is hyperbolic and another is elliptic.
Abstract: Biodisel is a type of biofuel having similar properties of diesel fuel but lacks substances (undesirable emissions) such as sulfur, nitrogen and aromatic polycyclic. Upon filtration of waste oil, the biodiesel fuel was produced via carrying out transestrification reaction of triglycerides followed by conducting viscosity, density, flash point, cloud point, pour point and copper strip corrosion tests on the samples and comparing with EN14214 and ASTM 6751 standards and all results were found in the permitted limit. The highest yield of biodiesel production reaction was found 46.6435 g when Sodium Hydroxide catalyst in amount of 0.375g was employed, 44.2347 g when Sodium methoxide catalyst in amount of 0.5g was employed and 56.5124 g when acid sulfuric catalyst in amount of 1g was employed and 47.3290 g when two stage reaction was done.
Abstract: High Pressure Raman scattering measurements of KDP:Mn were performed at room temperatures. The X-ray powder diffraction patterns taken at room temperature by Rietveld refinement showed that doped samples of KDP-Mn have the same tetragonal structure of a pure KDP crystal, but with a contraction of the crystalline cell. The behavior of the Raman spectra, in particular the emergence of a new modes at 330 cm-1, indicates that KDP:Mn undergoes a structural phase transition with onset at around 4 GP. First principle density-functional theory (DFT) calculations indicate that tetrahedral rotation with pressure is predominantly around the c crystalline direction. Theoretical results indicates that pressure induced tetrahedral rotations leads to change tetrahedral neighborhood, activating librations/bending modes observed for high pressure phase of KDP:Mn with stronger Raman activity.
Abstract: In hydrocyclones, the particle separation efficiency is
limited by the suspended fine particles, which are discharged with the
coarse product in the underflow. It is well known that injecting water
in the conical part of the cyclone reduces the fine particle fraction in
the underflow. This paper presents a mathematical model that
simulates the water injection in the conical component. The model
accounts for the fluid flow and the particle motion. Particle
interaction, due to hindered settling caused by increased density and
viscosity of the suspension, and fine particle entrainment by settling
coarse particles are included in the model. Water injection in the
conical part of the hydrocyclone is performed to reduce fine particle
discharge in the underflow. The model demonstrates the impact of
the injection rate, injection velocity, and injection location on the
shape of the partition curve. The simulations are compared with
experimental data of a 50-mm cyclone.
Abstract: Saddlepoint approximations is one of the tools to obtain
an expressions for densities and distribution functions. We approximate
the densities of the observed gaps between the hypopnea events
using the Huzurbazar saddlepoint approximation. We demonstrate the
density of a maximum likelihood estimator in exponential families.
Abstract: Partitions can play a significant role in minimising cochannel
interference of Wireless LANs by attenuating signals across
room boundaries. This could pave the way towards higher density
deployments in home and office environments through spatial
channel reuse. Yet, due to protocol limitations, the latest incantation
of IEEE 802.11 standard is still unable to take advantage of this fact:
Despite having clearly adequate Signal to Interference Ratio (SIR)
over co-channel neighbouring networks in other rooms, its goodput
falls significantly lower than its maximum in the absence of cochannel
interferers. In this paper, we describe how this situation can
be remedied via modest modifications to the standard.
Abstract: The present article comprises a theoretical study of
structures Performat radical (HCO3) with H2O molecule. We make
use of ab initio quantum chemical methods. Unrestricted Hartee-Fock
(UHF) with the basis set6-311+g(2df,2p) and density functional
theory (B3LYP) with the basis set 6-311+g(2df,2p) and also we done
atoms in molecules (AIM) theory for them. We have found four
stable geometries the PerformatRadical(HCO3) with H2O.
Abstract: This paper presents a novel CMOS four-transistor
SRAM cell for very high density and low power embedded SRAM
applications as well as for stand-alone SRAM applications. This cell
retains its data with leakage current and positive feedback without
refresh cycle. The new cell size is 20% smaller than a conventional
six-transistor cell using same design rules. Also proposed cell uses
two word-lines and one pair bit-line. Read operation perform from
one side of cell, and write operation perform from another side of
cell, and swing voltage reduced on word-lines thus dynamic power
during read/write operation reduced. The fabrication process is fully
compatible with high-performance CMOS logic technologies,
because there is no need to integrate a poly-Si resistor or a TFT load.
HSPICE simulation in standard 0.25μm CMOS technology confirms
all results obtained from this paper.
Abstract: The fine structure of supercavitation in the wake of a
symmetrical cylinder is studied with high-speed video cameras. The
flow is observed in a cavitation tunnel at the speed of 8m/sec when the
sidewall and the wake are partially filled with the massive cavitation
bubbles. The present experiment observed that a two-dimensional
ripple wave with a wave length of 0.3mm is propagated in a
downstream direction, and then abruptly increases to a thicker
three-dimensional layer. IR-photography recorded that the wakes
originated from the horseshoe vortexes alongside the cylinder. The
wake was developed to inside the dead water zone, which absorbed the
bubbly wake propelled from the separated vortices at the center of the
cylinder. A remote sensing classification technique (maximum most
likelihood) determined that the surface porosity was 0.2, and the mean
speed in the mixed wake was 7m/sec. To confirm the existence of
two-dimensional wave motions in the interface, the experiments were
conducted at a very low frequency, and showed similar gravity waves
in both the upper and lower interfaces.