Abstract: Nowadays, to decrease the number of downtimes in the industries such as metal mining, petroleum and chemical industries, predictive maintenance is crucial. In order to have efficient predictive maintenance, knowing the performance of critical equipment of production line such as pumps and hydro-cyclones under variable operating parameters, selecting best indicators of this equipment health situations, best locations for instrumentation, and also measuring of these indicators are very important. In this paper, computer aided engineering (CAE) tools are implemented to study some important elements of copper process line, namely slurry pumps and cyclone to predict the performance of these components under different working conditions. These modeling and simulations can be used in predicting, for example, the damage tolerance of the main shaft of the slurry pump or wear rate and location of cyclone wall or pump case and impeller. Also, the simulations can suggest best-measuring parameters, measuring intervals, and their locations.
Abstract: The separation efficiency of a hydrocyclone has
extensively been considered on the rigid particle assumption. A
collection of experimental studies have demonstrated their
discrepancies from the modeling and simulation results. These
discrepancies caused by the actual particle elasticity have generally
led to a larger amount of energy consumption in the separation
process. In this paper, the influence of particle elasticity on the
separation efficiency of a hydrocyclone system was investigated
through the Finite Element (FE) simulations using crude oil droplets
as the elastic particles. A Reitema-s design hydrocyclone with a
diameter of 8 mm was employed to investigate the separation
mechanism of the crude oil droplets from water. The cut-size
diameter eter of the crude oil was 10 - Ðçm in order to fit with the
operating range of the adopted hydrocylone model. Typical
parameters influencing the performance of hydrocyclone were varied
with the feed pressure in the range of 0.3 - 0.6 MPa and feed
concentration between 0.05 – 0.1 w%. In the simulation, the Finite
Element scheme was applied to investigate the particle-flow
interaction occurred in the crude oil system during the process. The
interaction of a single oil droplet at the size of 10 - Ðçm to the flow
field was observed. The feed concentration fell in the dilute flow
regime so the particle-particle interaction was ignored in the study.
The results exhibited the higher power requirement for the separation
of the elastic particulate system when compared with the rigid
particulate system.
Abstract: Hydrocyclones flow field study is conducted by performing a parametric study. Effect of cone angle on deoiling hydrocyclones flow behaviour is studied in this research. Flow field of hydrocyclone is obtained by three-dimensional simulations with OpenFOAM code. Because of anisotropic behaviour of flow inside hydrocyclones LES is a suitable method to predict the flow field since it resolves large scales and model isotropic small scales. Large eddy simulation is used to predict the flow behavior of three different cone angles. Differences in tangential velocity and pressure distribution are reported in some figures.
Abstract: In this research a comparison between k-epsilon and
LES model for a deoiling hydrocyclone is conducted. Flow field of
hydrocyclone is obtained by three-dimensional simulations with
OpenFOAM code. Potential of prediction for both methods of this
complex swirl flow is discussed. Large eddy simulation method
results have more similarity to experiment and its results are
presented in figures from different hydrocyclone cross sections.
Abstract: In hydrocyclones, the particle separation efficiency is
limited by the suspended fine particles, which are discharged with the
coarse product in the underflow. It is well known that injecting water
in the conical part of the cyclone reduces the fine particle fraction in
the underflow. This paper presents a mathematical model that
simulates the water injection in the conical component. The model
accounts for the fluid flow and the particle motion. Particle
interaction, due to hindered settling caused by increased density and
viscosity of the suspension, and fine particle entrainment by settling
coarse particles are included in the model. Water injection in the
conical part of the hydrocyclone is performed to reduce fine particle
discharge in the underflow. The model demonstrates the impact of
the injection rate, injection velocity, and injection location on the
shape of the partition curve. The simulations are compared with
experimental data of a 50-mm cyclone.
Abstract: In this research the separation efficiency of deoiling hydrocyclone is evaluated using three-dimensional simulation of multiphase flow based on Eulerian-Eulerian finite volume method. The mixture approach of Reynolds Stress Model is also employed to capture the features of turbulent multiphase swirling flow. The obtained separation efficiency of Colman's design is compared with available experimental data and showed that the separation curve of deoiling hydrocyclones can be predicted using numerical simulation.