Abstract: The studies concerned an effect of six variants of ion
exchange substrate (nutrient carriers with a different potential impact
on pH of soil solution) on vegetation of orchard grass during two
different periods (42 and 84 days). In the pot experiment plants were
grown on sand (model of degraded soil) and six mixtures of sand and
2% (v/v) additions of particular variants of ion exchange substrate
(with pH ranged from 5.5 to 8.0). The study results showed that the
addition of the substrate at pH=6.5 caused the highest increase in
plant yield after shorter vegetation period whereas the addition of the
substrate at pH=5.5 increased dry stem and root biomass of orchard
grass after longer vegetation period. Thus, the ion exchange substrate
at pH=6.5 can be recommended for restoration of exhausted soils
when shorter vegetation period is planned; the ion exchange substrate
at pH=5.5 can be used for the same purpose when longer periods of
vegetative growth are considered.
Abstract: Broccoli has been widely recognized as a wealthy
vegetable which contains multiple nutrients with potent anti-cancer
properties. Lamb’s lettuce has been used as food for many centuries
but only recently became commercially available and literature is
therefore exiguous concerning these vegetables. The aim of this work
was to evaluate the influence of the extraction conditions on the yield
of phenolic compounds and the corresponding antioxidant capacity of
broccoli and lamb’s lettuce. The results indicate that lamb’s lettuce,
compared to broccoli, contains simultaneously a large amount of total
polyphenols as well as high antioxidant activity. It is clearly
demonstrated that extraction solvent significantly influences the
antioxidant activity. Methanol is the solvent that can globally
maximize the antioxidant extraction yield. The results presented
herein prove lamb’s lettuce as a very interesting source of
polyphenols, and thus a potential health-promoting food.
Abstract: In a pilot plant scale of a fluidized bed reactor, a
reduction reaction of sodium sulfate by natural gas has been
investigated. Natural gas is applied in this study as a reductant. Feed
density, feed mass flow rate, natural gas and air flow rate
(independent parameters)and temperature of bed and CO
concentration in inlet and outlet of reactor (dependent parameters)
were monitored and recorded at steady state. The residence time was
adjusted close to value of traditional reaction [1]. An artificial neural
network (ANN) was established to study dependency of yield and
carbon gradient on operating parameters. Resultant 97% accuracy of
applied ANN is a good prove that natural gas can be used as a
reducing agent. Predicted ANN model for relation between other
sources carbon gradient (accuracy 74%) indicates there is not a
meaningful relation between other sources carbon variation and
reduction process which means carbon in granule does not have
significant effect on the reaction yield.
Abstract: Matching algorithms have significant importance in
speaker recognition. Feature vectors of the unknown utterance are
compared to feature vectors of the modeled speakers as a last step in
speaker recognition. A similarity score is found for every model in
the speaker database. Depending on the type of speaker recognition,
these scores are used to determine the author of unknown speech
samples. For speaker verification, similarity score is tested against a
predefined threshold and either acceptance or rejection result is
obtained. In the case of speaker identification, the result depends on
whether the identification is open set or closed set. In closed set
identification, the model that yields the best similarity score is
accepted. In open set identification, the best score is tested against a
threshold, so there is one more possible output satisfying the
condition that the speaker is not one of the registered speakers in
existing database. This paper focuses on closed set speaker
identification using a modified version of a well known matching
algorithm. The results of new matching algorithm indicated better
performance on YOHO international speaker recognition database.
Abstract: Buildings with floating column are highly undesirable built in seismically active areas. Many urban multi-storey buildings today have floating column buildings which are adopted to accommodate parking at ground floor or reception lobbies in the first storey. The earthquake forces developed at different floor levels in a building need to be brought down along the height to the ground by the shortest path; any deviation or discontinuity in this load transfer path results in poor performance of the building. Floating column buildings are severely damaged during earthquake. Damage on this structure can be reduce by taking the effect of infill wall. This paper presents the effect of stiffness of infill wall to the damage occurred in floating column building when ground shakes. Modelling and analysis are carried out by non linear analysis programme IDARC-2D. Damage occurred in beams, columns, storey are studied by formulating modified Park & Ang model to evaluate damage indices. Overall structural damage indices in buildings due to shaking of ground are also obtained. Dynamic response parameters i.e. lateral floor displacement, storey drift, time period, base shear of buildings are obtained and results are compared with the ordinary moment resisting frame buildings. Formation of cracks, yield, plastic hinge, are also observed during analysis.
Abstract: High purity hydrogen and the valuable by-product of carbon nanotubes (CNTs) can be produced by the methane catalytic decomposition. The methane conversion and the performance of CNTs were determined by the choices of catalysts and the condition of decomposition reaction. In this paper, Ni/MgO and Ni/O-D (oxidized diamond) catalysts were prepared by wetness impregnation method. The effects of reaction temperature and space velocity of methane on the methane conversion were investigated in a fixed-bed. The surface area, structure and micrography were characterized with BET, XPS, SEM, EDS technology. The results showed that the conversion of methane was above 8% within 150 min (T=500) for 33Ni/O-D catalyst and higher than 25% within 120 min (T=650) for 41Ni/MgO catalyst. The initial conversion increased with the increasing temperature of the decomposition reaction, but their catalytic activities decreased rapidly while at too higher temperature. To decrease the space velocity of methane was propitious to promote the methane conversion, but not favor of the hydrogen yields. The appearance of carbon resulted from the methane decomposition lied on the support type and the condition of catalytic reaction. It presented as fiber shape on the surface of Ni/O-D at the relatively lower temperature such as 500 and 550, but as grain shape stacked on and overlayed on the surface of the metal nickel while at 650. The carbon fiber can form on the Ni/MgO surface at 650 and the diameter of the carbon fiber increased with the decreasing space velocity.
Abstract: Metal cutting is a severe plastic deformation process
involving large strains, high strain rates, and high temperatures.
Conventional analysis of the chip formation process is based on bulk
material deformation disregarding the inhomogeneous nature of the
material microstructure. A series of orthogonal cutting tests of AISI
1045 and 1144 steel were conducted which yielded similar process
characteristics and chip formations. With similar shear angles and cut
chip thicknesses, shear strains for both chips were found to range
from 2.0 up to 2.8. The manganese-sulfide (MnS) precipitate in the
1144 steel has a very distinct and uniform shape which allows for
comparison before and after chip formation. From close observations
of MnS precipitates in the cut chips it is shown that the conventional
approach underestimates plastic strains in metal cutting.
Experimental findings revealed local shear strains around a value of
6. These findings and their implications are presented and discussed.
Abstract: In order to study the effects of supplemental irrigation, different levels of nitrogen chemical fertilizer and inoculation with rhizobium bacteria on the grain yield of chickpea, an experiment was carried out using split plot arrangement in randomize complete block design with three replication in agricultural researches station of Zanjan, Iran during 2009-2010 cropping season. The factors of experiment consisted of irritation (without irrigation (I1), irrigation at flowering stage (I2), irrigation at flowering and grain filling stages (I3) and full irrigation (I4)) and different levels of nitrogen fertilizer (without using of nitrogen fertilizer (N0), 75 kg.ha-1 (N75), 150 kg.ha-1 (N150) and inoculation with rhizobium bacteria (N4). The results of the analysis of variance showed that the effects of irrigation, nitrogen fertilizer levels and bacterial inoculation, were significant affect on number of pods per plant, number grains per plant, grain weight, grain yield, biological yield and harvest index at 1% probability level. Also Results showed that the grain yield in full irrigation treatment and inoculated with rhizobium bacteria was significantly higher than the other treatments.
Abstract: Dew harvesting needs only weak investment and
exploits a free, clean and inexhaustible energy. This study aims to
measure the relative contributions of dew and rain water in the
Mediterranean Dalmatian coast and islands of Croatia and determine
whether dew water is potable. Two sites were chosen, an open site on
the coast favourable to dew formation (Zadar) and a less favourable
site in a circus of mountains in Komiža (Vis Island). Between July
1st, 2003 and October 31st, 2006, dew hasbeen daily collected on a 1
m2 tilted (30°) test dew condenser together with ordinary
meteorological data (air temperature and relative humidity, cloud
coverage, windspeed and direction). The mean yearly cumulative
dew yields were found to be 20 mm (Zadar) and 9.3 mm (Komiža ).
During the dry season (May to October), monthly cumulative dew
water yield can represent up to 38% of water collected by rain fall. In
July 2003 and 2006, dew water represented about 120% of the
monthly cumulative rain water. Dew and rain water were analyzed in
Zadar. The corresponding parameters were measured: pH, electrical
conductivity, major anions (HCO3
-, Cl-, SO4
2-
, NO3
-
, ,) and major
cations (NH4
+, Na+, K+, Ca2+, Mg2+. Both dew and rain water are in
conformity with the WHO directives for potability except Mg2+.
Using existing roofs and refurbishing the abandoned impluviums to
permit dew collection could then provide a useful supplementary
amount of water, especially during the dry season.
Abstract: In this work, biohydrogen production via dark
fermentation from alcohol wastewater using upflow anaerobic sludge
blanket reactors (UASB) with a working volume of 4 L was
investigated to find the optimum conditions for a maximum hydrogen
yield. The system was operated at different COD loading rates (23,
31, 46 and 62 kg/m3d) at mesophilic temperature (37 ºC) and pH 5.5.
The seed sludge was pretreated before being fed to the UASB system
by boiling at 95 ºC for 15 min. When the system was operated under
the optimum COD loading rate of 46 kg/m3d, it provided the
hydrogen content of 27%, hydrogen yield of 125.1 ml H2/g COD
removed and 95.1 ml H2/g COD applied, hydrogen production rate of
18 l/d, specific hydrogen production rate of 1080 ml H2/g MLVSS d
and 1430 ml H2/ L d, and COD removal of 24%.
Abstract: The distillation process in the general sense is a
relatively simple technique from the standpoints of its principles.
When dedicating distillation to water treatment and specifically
producing fresh water from sea, ocean and/ briny waters it is
interesting to notice that distillation has no limitations or domains of
applicability regarding the nature or the type of the feedstock water.
This is not the case however for other techniques that are
technologically quite complex, necessitate bigger capital investments
and are limited in their usability. In a previous paper we have
explored some of the effects of temperature on yield. In this paper,
we continue building onto that knowledge base and focus on the
effects of several additional engineering and design variables on
productivity.
Abstract: Phaseolus coccineus L. is the third most important
cultivated Phaseolus species in the world. It is widely grown in
Latvia due to its earliness, good taste and uniform and qualitative
yield. Experiments were carried out in the laboratories of Department
of Food Technology and Agronomical Analysis Scientific Laboratory
at Latvia Universityof Agriculture. Beans (Phaseolus coccineus L.)
crude protein, crude ash content as well as colour measurements were
analyzed. Results show, that brown coloured beans have less crude
protein content than others, and ash content have significant
differences.
Abstract: The conjugate gradient optimization algorithm is combined with the modified back propagation algorithm to yield a computationally efficient algorithm for training multilayer perceptron (MLP) networks (CGFR/AG). The computational efficiency is enhanced by adaptively modifying initial search direction as described in the following steps: (1) Modification on standard back propagation algorithm by introducing a gain variation term in the activation function, (2) Calculation of the gradient descent of error with respect to the weights and gains values and (3) the determination of a new search direction by using information calculated in step (2). The performance of the proposed method is demonstrated by comparing accuracy and computation time with the conjugate gradient algorithm used in MATLAB neural network toolbox. The results show that the computational efficiency of the proposed method was better than the standard conjugate gradient algorithm.
Abstract: The effect of flooding can be a serious problem for
wheat farmers, even at dry land condition. Amount of flooding
damage depends on duration flooding, developmental stage, wheat
type and variety. Therefore as a factorial experiment in randomized
complete design based on winter bread wheat cultivars (Pishtaz,
Marvdasht, Shiraz, Zarin, Shahriar, C-81-4, Sardari, Agosta seed,
FGS and Azar2) at stages (Non- flooding stress, flooding at tillering
and stem elongation stages for 15 days) carried out in Faculty of
Agriculture, Razi University, Kermanshah, Iran. During flooding,
soil environment of plant roots were water saturated. Analysis of
variance showed that flooding had a significant effect on the number
of grains per spike, grain weight per spike and a grain weight. Hence
flooding reduces the number of grain per spike between 27.1 to 42.5
percent, grain weight per spike between 34.7 to 54.4 percent and
single grain weight between 12.1 to 15.1 percent. Effects of flooding
at the tillering stage reduced higher than stem elongation stage on
studied traits. The result also showed that flooding at tillering stage
delayed spikelet primordial and floret. Between wheat cultivars was
significant for traits, but were different reactions. "Shiraz", "Zarin"
and "Shahriar" had the most no. grain per spike, but "Zarin" and
"Sardari" had the most grain weight per spike and single grain
weight, respectively. Also, interaction between start of flooding and
cultivar was significant.
Abstract: Today, incorrect use of lands and land use changes,
excessive grazing, no suitable using of agricultural farms, plowing on
steep slopes, road construct, building construct, mine excavation etc
have been caused increasing of soil erosion and sediment yield. For
erosion and sediment estimation one can use statistical and empirical
methods. This needs to identify land unit map and the map of
effective factors. However, these empirical methods are usually time
consuming and do not give accurate estimation of erosion. In this
study, we applied GIS techniques to estimate erosion and sediment of
Menderjan watershed at upstream Zayandehrud river in center of
Iran. Erosion faces at each land unit were defined on the basis of land
use, geology and land unit map using GIS. The UTM coordinates of
each erosion type that showed more erosion amounts such as rills and
gullies were inserted in GIS using GPS data. The frequency of
erosion indicators at each land unit, land use and their sediment yield
of these indices were calculated. Also using tendency analysis of
sediment yield changes in watershed outlet (Menderjan hydrometric
gauge station), was calculated related parameters and estimation
errors. The results of this study according to implemented watershed
management projects can be used for more rapid and more accurate
estimation of erosion than traditional methods. These results can also
be used for regional erosion assessment and can be used for remote
sensing image processing.
Abstract: Low carbon deep drawing steel DC 01 according to EN 10130-91 was nitrooxidized in dissociated ammonia at 580°C/45 min and consequently oxidised at 380°C/5 min in vapour of distilled water. Material after nitrooxidation had 54 % increase of yield point, 34 % increase of strength and 10-times increased resistance to atmospheric corrosion in comparison to the material before nitrooxidation. The microstructure of treated material consisted of thin ε-phase layer connected to layer containing precipitated massive needle shaped Fe4N - γ' nitrides. This layer passed to a diffusion layer consisting of fine irregular shaped Fe16N2 - α'' nitrides regularly dispersed in ferritic matrix. Fatigue properties were examined under bending load with frequency of 20 kHz and sinusoidal symmetric cycle. The results confirmed positive influence of nitrooxidation on fatigue properties as fatigue limit of treated material was double in comparison to untreated material.
Abstract: Conventional approaches in the implementation of logic programming applications on embedded systems are solely of software nature. As a consequence, a compiler is needed that transforms the initial declarative logic program to its equivalent procedural one, to be programmed to the microprocessor. This approach increases the complexity of the final implementation and reduces the overall system's performance. On the contrary, presenting hardware implementations which are only capable of supporting logic programs prevents their use in applications where logic programs need to be intertwined with traditional procedural ones, for a specific application. We exploit HW/SW codesign methods to present a microprocessor, capable of supporting hybrid applications using both programming approaches. We take advantage of the close relationship between attribute grammar (AG) evaluation and knowledge engineering methods to present a programmable hardware parser that performs logic derivations and combine it with an extension of a conventional RISC microprocessor that performs the unification process to report the success or failure of those derivations. The extended RISC microprocessor is still capable of executing conventional procedural programs, thus hybrid applications can be implemented. The presented implementation is programmable, supports the execution of hybrid applications, increases the performance of logic derivations (experimental analysis yields an approximate 1000% increase in performance) and reduces the complexity of the final implemented code. The proposed hardware design is supported by a proposed extended C-language called C-AG.
Abstract: Effects of bio-nitrogen fertilizer (bio-N), as a partial
alternative to mineral-nitrogen fertilizer (mineral-N), on growth,
yield and yield quality of broccoli plants were investigated. Bio-N
was applied at 1, 2 or 3 doses in combination with 65% of the
recommended dose of mineral-N (bio-N1, bio-N2 or bio-N3 +
⅔mineral-N). However, 100% of the recommended dose of mineral-
N was applied as a control. Significant positive influences of the bio-
N3 + ⅔mineral-N treatment were observed on growth traits, leaf
contents of nitrogen, phosphorus, potassium, nitrate and nitrite, and
yield quality when compared to the other two combined treatments.
In contrast, there were no significant differences in these parameters
between the bio-N3 + ⅔mineral-N and the control treatments, except
for leaf contents of nitrate and nitrite. They showed lower contents in
the bio-N3 + ⅔mineral-N treatment than the control. Therefore, we
recommend using bio-N as a partial alternative to mineral-N for
healthy nutrition.
Abstract: Repeated observation of a given area over time yields
potential for many forms of change detection analysis. These
repeated observations are confounded in terms of radiometric
consistency due to changes in sensor calibration over time,
differences in illumination, observation angles and variation in
atmospheric effects.
This paper demonstrates applicability of an empirical relative
radiometric normalization method to a set of multitemporal cloudy
images acquired by Resourcesat1 LISS III sensor. Objective of this
study is to detect and remove cloud cover and normalize an image
radiometrically. Cloud detection is achieved by using Average
Brightness Threshold (ABT) algorithm. The detected cloud is
removed and replaced with data from another images of the same
area. After cloud removal, the proposed normalization method is
applied to reduce the radiometric influence caused by non surface
factors. This process identifies landscape elements whose reflectance
values are nearly constant over time, i.e. the subset of non-changing
pixels are identified using frequency based correlation technique. The
quality of radiometric normalization is statistically assessed by R2
value and mean square error (MSE) between each pair of analogous
band.
Abstract: Understanding how precipitation inter-annually
changes and its implication in agricultural drought and production change in winter wheat (Triticum aestivum L.) growth season is critical for crop production in China. MODIS Temperature-Vegetation Dryness Index (TVDI) and daily mean precipitation time series for the main growth season(Feb. to May) of winter wheat from 2000 to 2010
were used to analyze the distribution of trends of precipitation,
agricultural drought and winter wheat yield change respectively, and
relationships between them in North China region(Huang-huai-hai
region, HHH region), China. The results indicated that the trend of
precipitation in HHH region past 11 years was increasing, which had
induced generally corresponding decreasing trend of agricultural
drought and increasing trend of wheat yield, while the trend of drought
was spatially diverse. The study could provide a basis for agricultural
drought research during winter wheat season in HHH region under the
ground of climate change.