Abstract: In this paper, we evaluate the choice of suitable
quantization characteristics for both the decoder messages and the
received samples in Low Density Parity Check (LDPC) coded
systems using M-QAM (Quadrature Amplitude Modulation)
schemes. The analysis involves the demapper block that provides
initial likelihood values for the decoder, by relating its quantization
strategy of the decoder. A mapping strategy refers to the grouping of
bits within a codeword, where each m-bit group is used to select a
2m-ary signal in accordance with the signal labels. Further we
evaluate the system with mapping strategies like Consecutive-Bit
(CB) and Bit-Reliability (BR). A new demapper version, based on
approximate expressions, is also presented to yield a low complexity
hardware implementation.
Abstract: This paper presents a pulse doubling technique in a 12-pulse ac-dc converter which supplies direct torque controlled motor drives (DTCIMD-s) in order to have better power quality conditions at the point of common coupling. The proposed technique increases the number of rectification pulses without significant changes in the installations and yields in harmonic reduction in both ac and dc sides. The 12-pulse rectified output voltage is accomplished via two paralleled six-pulse ac-dc converters each of them consisting of three-phase diode bridge rectifier. An autotransformer is designed to supply the rectifiers. The design procedure of magnetics is in a way such that makes it suitable for retrofit applications where a six-pulse diode bridge rectifier is being utilized. Independent operation of paralleled diode-bridge rectifiers, i.e. dc-ripple re-injection methodology, requires a Zero Sequence Blocking Transformer (ZSBT). Finally, a tapped interphase reactor is connected at the output of ZSBT to double the pulse numbers of output voltage up to 24 pulses. The aforementioned structure improves power quality criteria at ac mains and makes them consistent with the IEEE-519 standard requirements for varying loads. Furthermore, near unity power factor is obtained for a wide range of DTCIMD operation. A comparison is made between 6- pulse, 12-pulse, and proposed converters from view point of power quality indices. Results show that input current total harmonic distortion (THD) is less than 5% for the proposed topology at various loads.
Abstract: An important goal of parboiling is a decrease of rice broken percentage and at the beginning Selected paddy of variety of rice Tarom and soaked at three different temperatures 45 Cº, 65 Cº and 80 Cº orderly for 5 hours, 4 hours and 1.5 hours to moisture of 40 % and then in steaming stage to operate these action two steaming methods are selected steaming under pressure condition and steaming in atmosphere pressure and In the first method after exerting air, the steam pressure is increase to 1 Kg/Cm2 which is done in two different duration times of 2.5 and 5 minutes and in second method used of three times of 5,10 and 15 minutes and dry to 8% moisture and decreases of rice broken percentage at best condition in variety of Tarom of 37.2 % to 7.3 % and increases yield percentage at best condition in variety of Tarom of 69.4 % to 75.93 % and bran percentage decreased in variety of Tarom of 9.53 % to 2.2-3.2 % and this issue cause increases yield percentage in rice and use of This method is very significant for our country because broken percentage of rice in our country is 23-33 %.
Abstract: One of the methods for detecting the target position
error in the laser tracking systems is using Four Quadrant (4Q)
detectors. If the coordinates of the target center is yielded through the
usual relations of the detector outputs, the results will be nonlinear,
dependent on the shape, target size and its position on the detector
screen. In this paper we have designed an algorithm with using
neural network that coordinates of the target center in laser tracking
systems is calculated by using detector outputs obtained from visual
modeling. With this method, the results except from the part related
to the detector intrinsic limitation, are linear and dependent from the
shape and target size.
Abstract: This study offers a new simple method for assessing
an axial part-through crack in a pipe wall. The method utilizes simple
approximate expressions for determining the fracture parameters K,
J, and employs these parameters to determine critical dimensions of a
crack on the basis of equality between the J-integral and the J-based
fracture toughness of the pipe steel. The crack tip constraint is taken
into account by the so-called plastic constraint factor C, by which the
uniaxial yield stress in the J-integral equation is multiplied. The
results of the prediction of the fracture condition are verified by burst
tests on test pipes.
Abstract: Air infiltration in mass scale industrial applications of
bio char production is inevitable. The presence of oxygen during the
carbonization process is detrimental to the production of biochar yield
and properties. The experiment was carried out on several wood
species in a fixed-bed pyrolyser under various fractions of oxygen
ranging from 0% to 11% by varying nitrogen and oxygen composition
in the pyrolysing gas mixtures at desired compositions. The bed
temperature and holding time were also varied. Process optimization
was carried out by Response Surface Methodology (RSM) by
employing Central Composite Design (CCD) using Design Expert 6.0
Software. The effect of oxygen ratio and holding time on biochar yield
within the range studied were statistically significant. From the
analysis result, optimum condition of 15.2% biochar yield of
mangrove wood was predicted at pyrolysis temperature of 403 oC,
oxygen percentage of 2.3% and holding time of two hours. This
prediction agreed well with the experiment finding of 15.1% biochar
yield.
Abstract: The neurogenic potential of many herbal extracts used
in Indian medicine is hitherto unknown. Extracts derived from
Clitoria ternatea Linn have been used in Indian Ayurvedic system of
medicine as an ingredient of “Medhya rasayana", consumed for
improving memory and longevity in humans and also in treatment of
various neurological disorders. Our earlier experimental studies with
oral intubation of Clitoria ternatea aqueous root extract (CTR) had
shown significant enhancement of learning and memory in postnatal
and young adult Wistar rats. The present study was designed to
elucidate the in vitro effects of 200ng/ml of CTR on proliferation,
differentiation and growth of anterior subventricular zone neural
stem cells (aSVZ NSC-s) derived from prenatal and postnatal rat
pups. Results show significant increase in proliferation and growth of
neurospheres and increase in the yield of differentiated neurons of
aSVZ neural precursor cells (aSVZNPC-s) at 7 days in vitro when
treated with 200ng/ml of CTR as compared to age matched control.
Results indicate that CTR has growth promoting neurogenic effect on
aSVZ neural stem cells and their survival similar to neurotrophic
factors like Survivin, Neuregulin 1, FGF-2, BDNF possibly the basis
for enhanced learning and memory.
Abstract: Maximal Ratio Combining (MRC) is considered the most complex combining technique as it requires channel coefficients estimation. It results in the lowest bit error rate (BER) compared to all other combining techniques. However the BER starts to deteriorate as errors are introduced in the channel coefficients estimation. A novel combining technique, termed Generalized Maximal Ratio Combining (GMRC) with a polynomial kernel, yields an identical BER as MRC with perfect channel estimation and a lower BER in the presence of channel estimation errors. We show that GMRC outperforms the optimal MRC scheme in general and we hereinafter introduce it to the scientific community as a new “supraoptimal" algorithm. Since diversity combining is especially effective in small femto- and pico-cells, internet-associated wireless peripheral systems are to benefit most from GMRC. As a result, many spinoff applications can be made to IP-based 4th generation networks.
Abstract: This paper presents the design, fabrication and
evaluation of magneto-rheological damper. Semi-active control
devices have received significant attention in recent years because
they offer the adaptability of active control devices without requiring
the associated large power sources. Magneto-Rheological (MR)
dampers are semi- active control devices that use MR fluids to
produce controllable dampers. They potentially offer highly reliable
operation and can be viewed as fail-safe in that they become passive
dampers if the control hardware malfunction. The advantage of MR
dampers over conventional dampers are that they are simple in
construction, compromise between high frequency isolation and
natural frequency isolation, they offer semi-active control, use very
little power, have very quick response, has few moving parts, have a
relax tolerances and direct interfacing with electronics. Magneto-
Rheological (MR) fluids are Controllable fluids belonging to the
class of active materials that have the unique ability to change
dynamic yield stress when acted upon by an electric or magnetic
field, while maintaining viscosity relatively constant. This property
can be utilized in MR damper where the damping force is changed by
changing the rheological properties of the fluid magnetically. MR
fluids have a dynamic yield stress over Electro-Rheological fluids
(ER) and a broader operational temperature range. The objective of
this papert was to study the application of an MR damper to vibration
control, design the vibration damper using MR fluids, test and
evaluate its performance. In this paper the Rheology and the theory
behind MR fluids and their use on vibration control were studied.
Then a MR vibration damper suitable for vehicle suspension was
designed and fabricated using the MR fluid. The MR damper was
tested using a dynamic test rig and the results were obtained in the
form of force vs velocity and the force vs displacement plots. The
results were encouraging and greatly inspire further research on the
topic.
Abstract: This work presents the experimental results obtained
at a pilot plant which works with a slow, wet and catalytic pyrolysis
process of dry fowl manure. This kind of process mainly consists in
the cracking of the organic matrix and in the following reaction of
carbon with water, which is either already contained in the organic
feed or added, to produce carbon monoxide and hydrogen. Reactions
are conducted in a rotating reactor maintained at a temperature of
500°C; the required amount of water is about 30% of the dry organic
feed. This operation yields a gas containing about 59% (on a volume
basis) of hydrogen, 17% of carbon monoxide and other products such
as light hydrocarbons (methane, ethane, propane) and carbon
monoxide in lesser amounts. The gas coming from the reactor can be
used to produce not only electricity, through internal combustion
engines, but also heat, through direct combustion in industrial
boilers. Furthermore, as the produced gas is devoid of both solid
particles and pollutant species (such as dioxins and furans), the
process (in this case applied to fowl manure) can be considered as an
optimal way for the disposal and the contemporary energetic
valorization of organic materials, in such a way that is not damaging
to the environment.
Abstract: Soft clays are defined as cohesive soil whose water
content is higher than its liquid limits. Thus, soil-cement mixing is
adopted to improve the ground conditions by enhancing the strength
and deformation characteristics of the soft clays. For the above
mentioned reasons, a series of laboratory tests were carried out to
study some fundamental mechanical properties of cement stabilized
soft clay. The test specimens were prepared by varying the portion of
ordinary Portland cement to the soft clay sample retrieved from the
test site of RECESS (Research Centre for Soft Soil). Comparisons
were made for both homogeneous and columnar system specimens
by relating the effects of cement stabilized clay of for 0, 5 and 10 %
cement and curing for 3, 28 and 56 days. The mechanical properties
examined included one-dimensional compressibility and undrained
shear strength. For the mechanical properties, both homogeneous and
columnar system specimens were prepared to examine the effect of
different cement contents and curing periods on the stabilized soil.
The one-dimensional compressibility test was conducted using an
oedometer, while a direct shear box was used for measuring the
undrained shear strength. The higher the value of cement content, the
greater is the enhancement of the yield stress and the decrease of
compression index. The value of cement content in a specimen is a
more active parameter than the curing period.
Abstract: Quantitative trait loci (QTL) experiments have yielded
important biological and biochemical information necessary for
understanding the relationship between genetic markers and
quantitative traits. For many years, most QTL algorithms only
allowed one observation per genotype. Recently, there has been an
increasing demand for QTL algorithms that can accommodate more
than one observation per genotypic distribution. The Bayesian
hierarchical model is very flexible and can easily incorporate this
information into the model. Herein a methodology is presented that
uses a Bayesian hierarchical model to capture the complexity of the
data. Furthermore, the Markov chain Monte Carlo model composition
(MC3) algorithm is used to search and identify important markers. An
extensive simulation study illustrates that the method captures the
true QTL, even under nonnormal noise and up to 6 QTL.
Abstract: Bioleaching of spent catalyst using moderate thermophilic chemolithotrophic acidophiles in growth medium without Fe source was investigated with two different pulp densities and three different size fractions. All the experiments were conducted on shake flasks at a temperature of 65 °C. The leaching yield of Ni and Al was found to be promising with very high leaching yield of 92-96% followed by Al as 41-76%, which means both Ni and Al leaching were favored by the moderate thermophilic bioleaching compared to the mesophilic bioleaching. The acid consumption was comparatively higher for the 10% pulp density experiments. Comparatively minimal difference in the leaching yield with different size fractions and different pulp densities show no requirement of grinding and using low pulp density less than 10%. This process would rather be economical as well as eco-friendly process for future optimization of the recovery of metal values from spent catalyst.
Abstract: Alpfa-fetoprotein and its fragments may be an important vehicle for targeted delivery of radionuclides to the tumor. We investigated the effect of conditions on the labeling of biologically active synthetic peptide based on the (F-afp) with technetium-99m. The influence of the nature of the buffer solution, pH, concentration of reductant, concentration of the peptide and the reaction temperature on the yield of labeling was examined. As a result, the following optimal conditions for labeling of (F-afp) are found: pH 8.5 (phosphate and bicarbonate buffers) and pH from 1.7 to 7.0 (citrate buffer). The reaction proceeds with sufficient yield at room temperature for 30 min at the concentration of SnCl2 and (Fafp) (F-afp) is to be less than 10 mkg/ml and 25 mkg/ml, respectively. Investigations of the test drug accumulation in the tumor cells of human breast cancer were carried out. Results can be assumed that the in vivo study of the (F-afp) in experimental tumor lesions will show concentrations sufficient for imaging these lesions by SPECT.
Abstract: IEEE has designed 802.11i protocol to address the
security issues in wireless local area networks. Formal analysis is
important to ensure that the protocols work properly without having
to resort to tedious testing and debugging which can only show the
presence of errors, never their absence. In this paper, we present
the formal verification of an abstract protocol model of 802.11i.
We translate the 802.11i protocol into the Strand Space Model and
then prove the authentication property of the resulting model using
the Strand Space formalism. The intruder in our model is imbued
with powerful capabilities and repercussions to possible attacks are
evaluated. Our analysis proves that the authentication of 802.11i is
not compromised in the presented model. We further demonstrate
how changes in our model will yield a successful man-in-the-middle
attack.
Abstract: Steel plate shear walls (SPSWs) in buildings are
known to be an effective means for resisting lateral forces. By using
un-stiffened walls and allowing them to buckle, their energy
absorption capacity will increase significantly due to the postbuckling
capacity. The post-buckling tension field action of SPSWs
can provide substantial strength, stiffness and ductility. This paper
presents the Finite Element Analysis of low yield point (LYP) steel
shear walls. In this shear wall system, the LYP steel plate is used for
the steel panel and conventional structural steel is used for boundary
frames. A series of nonlinear cyclic analyses were carried out to
obtain the stiffness, strength, deformation capacity, and energy
dissipation capacity of the LYP steel shear wall. The effect of widthto-
thickness ratio of steel plate on buckling behavior, and energy
dissipation capacities were studied. Good energy dissipation and
deformation capacities were obtained for all models.
Abstract: New lead-free ferroelectric relaxor ceramics were
prepared by conventional solid-state synthesis in the BaTiO3-Bi2O3-
Y2O3 systems. Some of these ceramics present a ferroelectric relaxor
with transition temperature close to room temperature. These new
materials are very interesting for applications and can replace leadbased
ceramic to prevent the toxic pollutions during the preparation
state. In the other hand, the energy band diagram shows the
potentiality of these compounds for the solar energy conversion.
Thus, some compositions have been tested successfully for H2
production upon visible light. The best activity occurs in alkaline
media with a rate evolution of about 0.15 mL g-1 mn-1 and a quantum
yield of 1% under polychromatic light.
Abstract: Sugarcane Shoots is an abundantly available
residual resources consisting of lignocelluloses which take it into
the benefit. The present study was focused on utilizing of
sugarcane shoot for reducing sugar production as a substrate in
ethanol production. Physical and chemical pretreatments of
sugarcane shoot were investigated. Results showed that the size of
sugarcane shoot influenced the cellulose content. The maximum
cellulose yield (60 %) can be obtained from alkaline pretreated
sugarcane shoot with 1.0 M NaOH at 30 oC for 90 min. The
cellulose yield reached up to 93.9% (w/w). Enzymatically
hydrolyzed of cellulosic residual in 0.04 citrate buffer (pH 5) with
celluclast 1.5L (0.7 FPU/ml) resulted in the highest amount of
reducing sugar at a rate of 32.1 g/l after 4 h incubation at 50°C,
and 100 oC for 5 min . Cellulose conversion was 55.5%.
Abstract: The article deals with the classification of alternative water resources in terms of potential risks which is the prerequisite for incorporating these water resources to the emergency plans. The classification is based on the quantification of risks resulting from possible damage, disruption or total destruction of water resource caused by natural and anthropogenic hazards, assessment of water quality and availability, traffic accessibility of the assessed resource and finally its water yield. The aim is to achieve the development of an integrated rescue system, which will be capable of supplying the population with drinking water on the whole stricken territory during the states of emergency.
Abstract: Simulation of the flow and sedimentation process in
the reservoir dams can be made by two methods of physical and mathematical modeling. The study area was within a region which
ranged from the Jelogir hydrometric station to the Karkheh reservoir
dam aimed at investigating the effects of stream tubes on the
GSTARS-3 model behavior. The methodologies was to run the model based on 5 stream tubes in order to observe the influence of
each scenario on longitudinal profiles, cross-section, flow velocity and bed load sediment size. Results further suggest that the use of
two stream tubes or more which result in the semi-two-dimensional
model will yield relatively closer results to the observational data
than a singular stream tube modeling. Moreover, the results of
modeling with three stream tubes shown to yield a relatively close
results with the observational data. The overall conclusion of the paper is with applying various stream tubes; it would be possible to yield a significant influence on the modeling behavior Vis-a Vis the bed load sediment size.