Abstract: The purpose of this study was to reduce patient
waiting times, improve system throughput and improve resources
utilization in radiology department. A discrete event simulation
model was developed using Arena simulation software to investigate
different alternatives to improve the overall system delivery based on
adding resource scenarios due to the linkage between patient waiting
times and resource availability. The study revealed that there is no
addition investment need to procure additional scanner but hospital
management deploy managerial tactics to enhance machine
utilization and reduce the long waiting time in the department.
Abstract: In this paper, effect of marginal quality groundwater
on yield of cotton crop and soil salinity was studied. In this
connection, three irrigation treatments each with four replications
were applied. These treatments were i) use of canal water (T1), ii) use
of marginal quality groundwater from tubewell (T2), and iii)
conjunctive use by mixing with the ratio of 1:1 of canal water and
marginal quality tubewell water (T3).
Water was applied to the crop cultivated in Kharif season 2011; its
quantity has been measured using cut-throat flume. Total 11 watering
each of 50 mm depth have been applied from 20th April to 20th July,
2011. Further, irrigations were stopped due to monsoon rainfall up to
crop harvesting.
Maximum crop yield (seed cotton) was observed under T1 which
was 1,517 kg/ha followed by T3 (mixed canal and tubewell water)
having 1009 kg/ha and T2 i.e. marginal quality groundwater having
709 kg/ha. This concludes that crop yield in T2 and T3 in comparison
to T1was reduced by about 53 and 30% respectively.
It has been observed that yield of cotton crop is below potential
limit for three treatments due to unexpected rainfall at the time of full
flowering season; thus the yield was adversely affected.
However, salt deposition in soil profiles was not observed that is
due to leaching effect of heavy rainfall occurred during monsoon
season.
Abstract: In this study which has been conducted in Akçasu
Forest Range District of Devrek Forest Directorate; 3 methods (weed
control with labourer power, cover removal with Hitachi F20
Excavator, and weed control with agricultural equipment mounted on
a Ferguson 240S agriculture tractor) were utilized in weed control
efforts in regeneration of degraded oriental beech forests have been
compared. In this respect, 3 methods have been compared by
determining certain work hours and standard durations of unit areas
(1 hectare). For this purpose, evaluating the tasks made with human
and machine force from the aspects of duration, productivity and
costs, it has been aimed to determine the most productive method in
accordance with the actual ecological conditions of research field.
Within the scope of the study, the time studies have been conducted
for 3 methods used in weed control efforts. While carrying out those
studies, the performed implementations have been evaluated by
dividing them into business stages. Also, the actual data have been
used while calculating the cost accounts. In those calculations, the
latest formulas and equations which are also used in developed
countries have been utilized. The variance of analysis (ANOVA) was
used in order to determine whether there is any statistically
significant difference among obtained results, and the Duncan test
was used for grouping if there is significant difference. According to
the measurements and findings carried out within the scope of this
study, it has been found during living cover removal efforts in
regeneration efforts in demolished oriental beech forests that the
removal of weed layer in 1 hectare of field has taken 920 hours with
labourer force, 15.1 hours with excavator and 60 hours with an
equipment mounted on a tractor. On the other hand, it has been
determined that the cost of removal of living cover in unit area (1
hectare) was 3220.00 TL for labourer power, 1250 TL for excavator
and 1825 TL for equipment mounted on a tractor.
According to the obtained results, it has been found that the
utilization of excavator in weed control effort in regeneration of
degraded oriental beech regions under actual ecological conditions of
research field has been found to be more productive from both of
aspects of duration and costs. These determinations carried out
should be repeated in weed control efforts in degraded forest fields
with different ecological conditions, it is compulsory for finding the
most efficient weed control method. These findings will light the way
of technical staff of forestry directorate in determination of the most
effective and economic weed control method. Thus, the more actual
data will be used while preparing the weed control budgets, and there
will be significant contributions to national economy. Also the results of this and similar studies are very important for developing the policies for our forestry in short and long term.
Abstract: Liposome plays an important role in medical and
pharmaceutical science as e.g. nano scale drug carriers. Liposomes
are vesicles of varying size consisting of a spherical lipid bilayer and
an aqueous inner compartment. Magnet-driven liposome used for the
targeted delivery of drugs to organs and tissues. These liposome
preparations contain encapsulated drug components and finely
dispersed magnetic particles.
Liposomes are vesicles of varying size consisting of a spherical
lipid bilayer and an aqueous inner compartment that are generated in
vitro. These are useful in terms of biocompatibility, biodegradability,
and low toxicity, and can control biodistribution by changing the size,
lipid composition, and physical characteristics. Furthermore,
liposomes can entrap both hydrophobic and hydrophilic drugs and are
able to continuously release the entrapped substrate, thus being useful
drug carriers. Magnetic liposomes (MLs) are phospholipid vesicles
that encapsulate magneticor paramagnetic nanoparticles. They are
applied as contrast agents for magnetic resonance imaging (MRI).
The biological synthesis of nanoparticles using plant extracts plays
an important role in the field of nanotechnology. Green-synthesized
magnetite nanoparticles-protein hybrid has been produced by treating
Iron (III) / Iron (II) chloride with the leaf extract of Datura inoxia.
The phytochemicals present in the leaf extracts act as a reducing as
well stabilizing agents preventing agglomeration, which include
flavonoids, phenolic compounds, cardiac glycosides, proteins and
sugars.
The magnetite nanoparticles-protein hybrid has been trapped
inside the aqueous core of the liposome prepared by reversed phase
evaporation (REV) method using oleic and linoleic acid which has
been shown to be driven under magnetic field confirming the
formation magnetic liposome (ML). Chemical characterization of
stealth magnetic liposome has been performed by breaking the
liposome and release of magnetic nanoparticles. The presence iron
has been confirmed by colour complex formation with KSCN and
UV-Vis study using spectrophotometer Cary 60, Agilent.
This magnet driven liposome using nanoparticles-protein hybrid
can be a smart vesicles for the targeted drug delivery.
Abstract: Many wireless sensor network applications require
K-coverage of the monitored area. In this paper, we propose a
scalable harmony search based algorithm in terms of execution
time, K-Coverage Enhancement Algorithm (KCEA), it attempts to
enhance initial coverage, and achieve the required K-coverage degree
for a specific application efficiently. Simulation results show that
the proposed algorithm achieves coverage improvement of 5.34%
compared to K-Coverage Rate Deployment (K-CRD), which achieves
1.31% when deploying one additional sensor. Moreover, the proposed
algorithm is more time efficient.
Abstract: Nowadays social media information, such as news,
links, images, or VDOs, is shared extensively. However, the
effectiveness of disseminating information through social media
lacks in quality: less fact checking, more biases, and several rumors.
Many researchers have investigated about credibility on Twitter, but
there is no the research report about credibility information on
Facebook. This paper proposes features for measuring credibility on
Facebook information. We developed the system for credibility on
Facebook. First, we have developed FB credibility evaluator for
measuring credibility of each post by manual human’s labelling. We
then collected the training data for creating a model using Support
Vector Machine (SVM). Secondly, we developed a chrome extension
of FB credibility for Facebook users to evaluate the credibility of
each post. Based on the usage analysis of our FB credibility chrome
extension, about 81% of users’ responses agree with suggested
credibility automatically computed by the proposed system.
Abstract: In order to manufacture short gap single Si nanowire
(NW) field effect transistor (FET) by imprinting and transferring
method, we introduce the method using Al2O3 sacrificial layer. The
diameters of cylindrical Si NW addressed between Au electrodes by
dielectrophoretic (DEP) alignment method are controlled to 106, 128,
and 148 nm. After imprinting and transfer process, cylindrical Si NW
is embedded in PVP adhesive and dielectric layer. By curing
transferred cylindrical Si NW and Au electrodes on PVP-coated p++ Si
substrate with 200nm-thick SiO2, 3μm gap Si NW FET fabrication
was completed. As the diameter of embedded Si NW increases, the
mobility of FET increases from 80.51 to 121.24 cm2/V·s and the
threshold voltage moves from –7.17 to –2.44 V because the ratio of
surface to volume gets reduced.
Abstract: Background: Taiwan now is an aging society. Research
on the elderly should not be confined to caring for seniors, but should
also be focused on ways to improve health and the quality of life.
Senior citizens who participate in volunteer services could become
less lonely, have new growth opportunities, and regain a sense of
accomplishment. Thus, the question of how to get the elderly to
participate in volunteer service is worth exploring. Objective: Apply
the Transtheoretical Model to understand stages of change in regular
volunteer service and voluntary service behaviour among the seniors.
Methods: 1525 adults over the age of 65 from the Renai district of
Keelung City were interviewed. The research tool was a
self-constructed questionnaire, and individual interviews were
conducted to collect data. Then the data was processed and analyzed
using the IBM SPSS Statistics 20 (Windows version) statistical
software program. Results: In the past six months, research subjects
averaged 9.92 days of volunteer services. A majority of these elderly
individuals had no intention to change their regular volunteer services.
We discovered that during the maintenance stage, the self-efficacy for
volunteer services was higher than during all other stages, but
self-perceived barriers were less during the preparation stage and
action stage. Self-perceived benefits were found to have an important
predictive power for those with regular volunteer service behaviors in
the previous stage, and self-efficacy was found to have an important
predictive power for those with regular volunteer service behaviors in
later stages. Conclusions/Implications for Practice: The research
results support the conclusion that community nursing staff should
group elders based on their regular volunteer services change stages
and design appropriate behavioral change strategies.
Abstract: The objective of the present study is to determine
better eye end design of a mono leaf spring used in light motor
vehicle. A conventional 65Si7 spring steel leaf spring model with
standard eye, casted and riveted eye end are considered. The CAD
model of the leaf springs is prepared in CATIA and analyzed using
ANSYS. The standard eye, casted and riveted eye leaf springs are
subjected to similar loading conditions. The CAE analysis of the leaf
spring is performed for various parameters like deflection and Von-
Mises stress. Mass reduction of 62.9% is achieved in case of riveted
eye mono leaf spring as compared to standard eye mono leaf spring
for the same loading conditions.
Abstract: This paper provides a comparative study on the
performances of standard PID and adaptive PID controllers tested on
travel angle of a 3-Degree-of-Freedom (3-DOF) Quanser bench-top
helicopter. Quanser, a well-known manufacturer of educational
bench-top helicopter has developed Proportional Integration
Derivative (PID) controller with Linear Quadratic Regulator (LQR)
for all travel, pitch and yaw angle of the bench-top helicopter. The
performance of the PID controller is relatively good; however, its
performance could also be improved if the controller is combined
with adaptive element. The objective of this research is to design
adaptive PID controller and then compare the performances of the
adaptive PID with the standard PID. The controller design and test is
focused on travel angle control only. Adaptive method used in this
project is self-tuning controller, which controller’s parameters are
updated online. Two adaptive algorithms those are pole-placement
and deadbeat have been chosen as the method to achieve optimal
controller’s parameters. Performance comparisons have shown that
the adaptive (deadbeat) PID controller has produced more desirable
performance compared to standard PID and adaptive (poleplacement).
The adaptive (deadbeat) PID controller attained very fast
settling time (5 seconds) and very small percentage of overshoot (5%
to 7.5%) for 10° to 30° step change of travel angle.
Abstract: Periventricular Leukomalacia (PVL) is a White Matter
Injury (WMI) of preterm neonatal brain. Objectives of the study were
to assess the neuro-developmental outcome at one year of age and to
determine a good protocol of cranial ultrasonography to detect PVL.
Two hundred and sixty four preterm neonates were included in the
study. Series of cranial ultrasound scans were done by using a
dedicated neonatal head probe 4-10 MHz of Logic e portable
ultrasound scanner. Clinical history of seizures, abnormal head
growth (hydrocephalus or microcephaly) and developmental
milestones were assessed and neurological examinations were done
until one year of age. Among live neonates, 57% who had cystic PVL
(Grades 2 and 3) manifested as cerebral palsy. In conclusion cystic
PVL has permanent neurological disabilities like cerebral palsy.
Good protocol of real time cranial ultrasonography to detect PVL is
to perform scans at least once a week until one month and at term (40
weeks of gestation).
Abstract: Science and technology has a major impact on many
societal domains such as communication, medicine, food,
transportation, etc. However, this dominance of modern technology
can have a negative unintended impact on indigenous systems, and in
particular on indigenous foods. This problem serves as a motivation
to this study whose aim is to examine the perceptions of learners on
the usefulness of Information and Communication Technologies
(ICTs) for learning about indigenous foods. This aim will be
subdivided into two types of research objectives. The design and
identification of theories and models will be achieved using literature
content analysis. The objective on the empirical testing of such
theories and models will be achieved through the survey of
Hospitality studies learners from different schools in the iLembe and
Umgungundlovu Districts of the South African Kwazulu-Natal
province. SPSS is used to quantitatively analyze the data collected by
the questionnaire of this survey using descriptive statistics and
Pearson correlations after the assessment of the validity and the
reliability of the data. The main hypothesis behind this study is that
there is a connection between the demographics of learners, their
perceptions on the usefulness of ICTs for learning about indigenous
foods, and the following personality and eLearning related theories
constructs: Computer self-efficacy, Trust in ICT systems, and
Conscientiousness; as suggested by existing studies on learning
theories. This hypothesis was fully confirmed by the survey
conducted by this study except for the demographic factors where
gender and age were not found to be determinant factors of learners’
perceptions on the usefulness of ICTs for learning about indigenous
foods.
Abstract: Geopolymer concretes are new class of construction
materials that have emerged as an alternative to Ordinary Portland
cement concrete. Considerable researches have been carried out on
material development of geopolymer concrete; however, a few studies
have been reported on the structural use of them. This paper presents
the bond behaviors of reinforcement embedded in fly ash based
geopolymer concrete. The development lengths of reinforcement for
various compressive strengths of concrete, 20, 30 and 40 MPa, and
reinforcement diameters, 10, 16 and 25 mm, are investigated. Total 27
specimens were manufactured and pull-out test according to EN 10080
was applied to measure bond strength and slips between concrete and
reinforcements. The average bond strengths decreased from 23.06MPa
to 17.26 MPa, as the diameters of reinforcements increased from
10mm to 25mm. The compressive strength levels of geopolymer
concrete showed no significant influence on bond strengths in this
study. Also, the bond-slip relations between geopolymer concrete and
reinforcement are derived using non-linear regression analysis for
various experimental conditions.
Abstract: Systems Engineering plays a key role during industrial
product development of complex technical systems. The need for
systems engineers in industry is growing. But there is a gap between
the industrial need and the academic education. Normally the
academic education is focused on the domain specific design,
implementation and testing of technical systems. Necessary systems
engineering expertise like knowledge about requirements analysis,
product cost estimation, management or social skills are poorly
taught. Thus there is the need of new academic concepts for teaching
systems engineering skills. This paper presents a project-orientated
training concept to prepare students from different technical degree
programs for systems engineering activities. The training concept has
been initially implemented and applied in the industrial engineering
master program of the University of Applied Sciences Offenburg.
Abstract: The problematic of gender and socioeconomic status
biased differences in academic motivation patterns is discussed.
Gender identity is understood according to symbolic interactionism
perspective: as a result of reflected appraisals, social comparisons,
self-attributions, and identifications, shaped by social environment
and family context. The effects of socioeconomic status on academic
motivation are conceptualized according to Bourdieu’s habitus
concept, reflecting the role of unconscious and internalized cultural
signals, proper to low and high socioeconomic status family contexts.
Since families differ by various socioeconomic features, the
hypothesis about possible impact of parents’ socioeconomic status on
their children’s academic motivation interfering with gender
socialization effects is held. The survey, aiming to seize gender
differences in academic motivation and self-recorded improvementoriented
efforts as a result of socialization processes operating in the
families of low and high socioeconomic status, was designed. The
results of Lithuanian higher education students’ survey are presented
and discussed.
Abstract: TiO2 thin films have been prepared by the sol-gel dipcoating
technique in order to elaborate antireflective thin films for
monocrystalline silicon (mono-Si). The titanium isopropoxyde was
chosen as a precursor with hydrochloric acid as a catalyser for
preparing a stable solution. The optical properties have been tailored
with varying the solution concentration, the withdrawn speed, and the
heat-treatment. We showed that using a TiO2 single layer with 64.5
nm in thickness, heat-treated at 450°C or 300°C reduces the mono-Si
reflection at a level lower than 3% over the broadband spectral
domains [669-834] nm and [786-1006] nm respectively. Those latter
performances are similar to the ones obtained with double layers of
low and high refractive index glasses respectively.
Abstract: The continuous decline of petroleum and natural gas
reserves and non linear rise of oil price has brought about a
realisation of the need for a change in our perpetual dependence on
the fossil fuel. A day to day increased consumption of crude and
petroleum products has made a considerable impact on our foreign
exchange reserves. Hence, an alternate resource for the conversion of
energy (both liquid and gas) is essential for the substitution of
conventional fuels. Biomass is the alternate solution for the present
scenario. Biomass can be converted into both liquid as well as
gaseous fuels and other feedstocks for the industries.
Abstract: The exact theoretical expression describing the
probability distribution of nonlinear sea-surface elevations derived
from the second-order narrowband model has a cumbersome form
that requires numerical computations, not well-disposed to theoretical
or practical applications. Here, the same narrowband model is reexamined
to develop a simpler closed-form approximation suitable
for theoretical and practical applications. The salient features of the
approximate form are explored, and its relative validity is verified
with comparisons to other readily available approximations, and
oceanic data.
Abstract: The globalization of markets, the need to develop
competitive advantages and core competencies, among other things,
lead organizations to increasingly cross borders to operate in other
countries. The expatriation of professionals who go to work in
another country besides their own becomes increasingly common. In
order to generate data about this issue, research was conducted
concerning the perception of expatriate employees concerning
expatriation success. The research method used was case study
through a qualitative approach. This research was done through
interviews with five India expatriates and five China expatriates,
interview with expatriate department heads and analysis of company
documents. It was found that there are differences between the
organizational perception and perception of expatriates of what
constitutes mission success. The paper also provides suggestions for
further research and suggestions for future expatriates.
Abstract: The ad hoc networks are the future of wireless
technology as everyone wants fast and accurate error free information
so keeping this in mind Bit Error Rate (BER) and power is optimized
in this research paper by using the Genetic Algorithm (GA). The
digital modulation techniques used for this paper are Binary Phase
Shift Keying (BPSK), M-ary Phase Shift Keying (M-ary PSK), and
Quadrature Amplitude Modulation (QAM). This work is
implemented on Wireless Ad Hoc Networks (WLAN). Then it is
analyze which modulation technique is performing well to optimize
the BER and power of WLAN.