Abstract: A numerical study on the effect of side-dump angle on
fuel droplets sizing and effective mass fraction have been
investigated in present paper. The mass of fuel vapor inside the
flammability limit is named as the effective mass fraction. In the first
step we have considered a side-dump combustor with dump angle of
0o (acrossthe cylinder) and by increasing the entrance airflow velocity
from 20 to 30, 40 and 50 (m/s) respectively, the mean diameter of
fuel droplets sizing and effective mass fraction have been studied.
After this step, we have changed the dump angle from 0o to 30o,45o
and finally 60o in direction of cylinderand also we have increased the
entrance airflow velocity from 20 up to 50 (m/s) with the amount of
growth of 10(m/s) in each step, to examine its effects on fuel droplets
sizing as well as effective mass fraction. With rise of entrance airflow
velocity, these calculations are repeated in each step too. The results
show, with growth of dump-angle the effective mass fraction has
been decreased and the mean diameter of droplets sizing has been
increased. To fulfill the calculations a modified version of KIVA-3V
code which is a transient, three-dimensional, multiphase,
multicomponent code for the analysis of chemically reacting flows
with sprays, is used.
Abstract: The present work involves measurements to examine
the effects of initial conditions on aerodynamic and acoustic
characteristics of a Jet at M=0.8 by changing the orientation of sharp
edged orifice plate. A thick plate with chamfered orifice presented divergent and convergent openings when it was flipped over. The centerline velocity was found to decay more rapidly for divergent
orifice and that was consistent with the enhanced mass entrainment
suggesting quicker spread of the jet compared with that from the convergent orifice. The mixing layer region elucidated this effect of
initial conditions at an early stage – the growth was found to be comparatively more pronounced for the divergent orifice resulting in
reduced potential core size. The acoustic measurements, carried out in the near field noise region outside the jet within potential core
length, showed the jet from the divergent orifice to be less noisy. The frequency spectra of the noise signal exhibited that in the initial
region of comparatively thin mixing layer for the convergent orifice,
the peak registered a higher SPL and a higher frequency as well. The noise spectra and the mixing layer development suggested a direct correlation between the coherent structures developing in the initial
region of the jet and the noise captured in the surrounding near field.
Abstract: Today advertising is actively penetrating into many spheres of our lives. We cannot imagine the existence of a lot of economic activities without advertising. That mostly concerns trade and services. Everyone of us should look better into the everyday communication and carefully consider the amount and the quality of the information we receive as well as its influence on our behaviour. Special attention should be paid to the young generation. Theoretical and practical research has proved the ever growing influence of information (especially the one contained in advertising) on a society; on its economics, culture, religion, politics and even people-s private lives and behaviour. Children have plenty of free time and, therefore, see a lot of different advertising. Though education of children is in the hands of parents and schools, advertising makers and customers should think with responsibility about the selection of time and transmission channels of child targeted advertising. The purpose of the present paper is to investigate the influence of advertising upon consumer views and behaviour of children in different age groups. The present investigation has clarified the influence of advertising as a means of information on a certain group of society, which in the modern information society is the most vulnerable – children. In this paper we assess children-s perception and their understanding of advertising.
Abstract: People at workplace always face with stress and feel it in their lives. There are many factors that create stress and mobbing is one of them. Mobbing is a psychological terror, conducted systematically toward an individual by others at the same workplace. Mobbing started to become a famous subject last years in U.S and Europe. In Turkey, it is a new concept not because it does not occur, because of human nature that does not allow confessing it. Mobbing is being ignored by people, organizations and also government in our country. The focus of this study will be mobbing in Turkey by examining the workplace mobbing among Turkish academicians. There are other studies about mobbing in Turkey but none of them studied academy. Because mobbing methods change according to sectors and occupations, it is important to analyze each sector to understand the methods used in mobbing and the reactions of victims to these actions. The concept is analyzed in detail before focusing on mobbing at universities. This paper will be unique because there is no information about this specific subject in Turkish literature. In this paper, both qualitative and quantitative methods will be used to describe the mobbing at Turkish academic environment.
Abstract: Malaysia has successfully applied economic planning
to guide the development of the country from an economy of
agriculture and mining to a largely industrialised one. Now, with its
sights set on attaining the economic level of a fully developed nation
by 2020, the planning system must be made even more efficient and
focused.
It must ensure that every investment made in the country, contribute
towards creating the desirable objective of a strong, modern,
internationally competitive, technologically advanced, post-industrial
economy. Cities in Malaysia must also be fully aware of the enormous
competition it faces in a region with rapidly expanding and
modernising economies, all contending for the same pool of potential
international investments.
Efficiency of urban governance is also fundamental issue in
development characterized by sustainability, subsidiarity, equity,
transparency and accountability, civic engagement and citizenship, and
security. As described above, city competitiveness is harnessed
through 'city marketing and city management'.
High technology and high skilled industries, together with finance,
transportation, tourism, business, information and professional
services shopping and other commercial activities, are the principal
components of the nation-s economy, which must be developed to a
level well beyond where it is now. In this respect, Kuala Lumpur being
the premier city must play the leading role.
Abstract: In this paper, modeling of an acoustic enclosed
vehicle cabin has been carried out by using boundary element
method. Also, the second purpose of this study is analyzing of linear
wave equation in an acoustic field. The resultants of this modeling
consist of natural frequencies that have been compared with
resultants derived from finite element method. By using numerical
method (boundary element method) and after solution of wave
equation inside an acoustic enclosed cabin, this method has been
progressed to simulate noise inside a simple vehicle cabin.
Abstract: Brushless DC motor with high torque density and slim
topology for easy loading for robot system is proposed and
manufactured. Electromagnetic design is executed by equivalent
magnetic circuit model and numerical analysis. Manufactured motor is
tested and verified characteristics comparing with conventional BLDC
motor.
Abstract: In this paper a study on the vibration of thin
cylindrical shells with ring supports and made of functionally
graded materials (FGMs) composed of stainless steel and
nickel is presented. Material properties vary along the
thickness direction of the shell according to volume fraction
power law. The cylindrical shells have ring supports which are
arbitrarily placed along the shell and impose zero lateral
deflections. The study is carried out based on third order shear
deformation shell theory (T.S.D.T). The analysis is carried out
using Hamilton-s principle. The governing equations of motion of
FGM cylindrical shells are derived based on shear deformation
theory. Results are presented on the frequency characteristics,
influence of ring support position and the influence of boundary
conditions. The present analysis is validated by comparing results
with those available in the literature.
Abstract: Ascorbic acid (AA), commonly known as vitamin C, is essential for normal functioning of the body and maintenance of metabolic integrity. Among its various roles are as an antioxidant, a cofactor in collagen formation and other reactions, as well as reducing physical stress and maintenance of the immune system. Recent collaborative research between the Australian Defence Science and Technology Organisation (DSTO) in Scottsdale, Tasmania and RMIT University has sought to overcome the problems arising from the inherent instability of ascorbic acid during processing and storage of foods. The recent work has demonstrated the potential of microencapsulation by spray drying as a means to enhance retention. The purpose of this current study has been focused upon the influence of spray drying conditions on the properties of encapsulated ascorbic acid. The process was carried out according to a central composite design. Independent variables were: inlet temperature (80-120° C) and feed flow rate (7-14 mL/minute). Process yield, ascorbic acid loss, moisture content, water activity and particle size distribution were analysed as responses. The results have demonstrated the potential of microencapsulation by spray drying as a means to enhance retention. Vitamin retention, moisture content, water activity and process yield were influenced positively by inlet air temperature and negatively by feed flow rate.
Abstract: This contribution was developed from a research
within the doctoral thesis. Its object was to create multimedia
materials for sport gymnastics. Consequently we surveyed the
influence of its practical application on the efficiency of schooling at
a university. We verified the prescribed hypothesis of the efficiency
of the teaching process using the method of single-factor experiment,
where the entrance independent variable was the change of system of
tuition and the outgoing dependent variable was the change of level
of acquired motor skills. The results confirmed the positive impact of
using multimedia materials on the efficiency of the teaching process.
Further, with the aid of questionnaires, we evaluated how the tested
subjects perceive the innovative methods in sport gymnastics. The
responses showed that the students rate the application of multimedia
materials very positively.
Abstract: The conventional assessment of human semen is a
highly subjective assessment, with considerable intra- and interlaboratory
variability. Computer-Assisted Sperm Analysis (CASA)
systems provide a rapid and automated assessment of the sperm
characteristics, together with improved standardization and quality
control. However, the outcome of CASA systems is sensitive to the
method of experimentation. While conventional CASA systems use
digital microscopes with phase-contrast accessories, producing
higher contrast images, we have used raw semen samples (no
staining materials) and a regular light microscope, with a digital
camera directly attached to its eyepiece, to insure cost benefits and
simple assembling of the system. However, since the accurate finding
of sperms in the semen image is the first step in the examination and
analysis of the semen, any error in this step can affect the outcome of
the analysis. This article introduces and explains an algorithm for
finding sperms in low contrast images: First, an image enhancement
algorithm is applied to remove extra particles from the image. Then,
the foreground particles (including sperms and round cells) are
segmented form the background. Finally, based on certain features
and criteria, sperms are separated from other cells.
Abstract: Grasslands of Iran are encountered with a vast
desertification and destruction. Some legumes are plants of forage
importance with high palatability. Studied legumes in this project are
Onobrychis, Medicago sativa (alfalfa) and Trifolium repens. Seeds
were cultivated in research field of Kaboutarabad (33 km East of
Isfahan, Iran) with an average 80 mm. annual rainfall. Plants were
cultivated in a split plot design with 3 replicate and two water
treatments (weekly irrigation, and under stress with same amount per
15 days interval). Water entrance to each plots were measured by
Partial flow. This project lasted 20 weeks. Destructive samplings
(1m2 each time) were done weekly. At each sampling plants were
gathered and weighed separately for each vegetative parts. An Area
Meter (Vista) was used to measure root surface and leaf area. Total
shoot and root fresh and dry weight, leaf area index and soil coverage
were evaluated too. Dry weight was achieved in 750c oven after 24
hours. Statgraphic and Harvard Graphic software were used to
formulate and demonstrate the parameters curves due to time. Our
results show that Trifolium repens has affected 60 % and Medicago
sativa 18% by water stress. Onobrychis total fresh weight was
reduced 45%. Dry weight or Biomass in alfalfa is not so affected by
water shortage. This means that in alfalfa fields we can decrease the
irrigation amount and have some how same amount of Biomass.
Onobrychis show a drastic decrease in Biomass. The increases in
total dry matter due to time in studied plants are formulated. For
Trifolium repens if removal or cattle entrance to meadows do not
occurred at perfect time, it will decrease the palatability and water
content of the shoots. Water stress in a short period could develop the
root system in Trifolium repens, but if it last more than this other
ecological and soil factors will affect the growth of this plant. Low
level of soil water is not so important for studied legume forges. But
water shortage affect palatability and water content of aerial parts.
Leaf area due to time in studied legumes is formulated. In fact leaf
area is decreased by shortage in available water. Higher leaf area
means higher forage and biomass production. Medicago and
Onobrychis reach to the maximum leaf area sooner than Trifolium
and are able to produce an optimum soil cover and inhibit the
transpiration of soil water of meadows. Correlation of root surface to
Total biomass in studied plants is formulated. Medicago under water
stress show a 40% decrease in crown cover while at optimum
condition this amount reach to 100%. In order to produce forage in
areas without soil erosion Medicago is the best choice even with a
shortage in water resources. It is tried to represent the growth
simulation of three famous Forage Legumes. By growth simulation
farmers and range managers could better decide to choose best plant
adapted to water availability without designing different time and
labor consuming field experiments.
Abstract: Debates on residential satisfaction topic have been
vigorously discussed in family house setting. Nonetheless, less or
lack of attention was given to survey on student residential
satisfaction in the campus house setting. This study, however, tried to
fill in the gap by focusing more on the relationship between students-
socio-economic backgrounds and student residential satisfaction with
their on-campus student housing facilities. Two-stage cluster
sampling method was employed to classify the respondents. Then,
self-administered questionnaires were distributed face-to-face to the
students. In general, it was confirmed that the students- socioeconomic
backgrounds have significantly influence the students-
satisfaction with their on-campus student housing facilities. The main
influential factors were revealed as the economic status, sense of
sharing, and the ethnicity of roommates. Likewise, this study could
also provide some useful feedback for the universities administration
in order to improve their student housing facilities.
Abstract: Recent environmental turbulence including financial
crisis, intensified competitive forces, rapid technological change and
high market turbulence have dramatically changed the current
business climate. The managers firms have to plan and decide what
the best approaches that best fit their firms in order to pursue superior
performance. This research aims to examine the influence of strategic
reasoning and top level managers- individual characteristics on the
effectiveness of organizational improvisation and firm performance.
Given the lack of studies on these relationships in the previous
literature, there is significant contribution to the body of knowledge
as well as for managerial practices. 128 responses from top
management of technology-based companies in Malaysia were used
as a sample. Three hypotheses were examined and the findings
confirm that (a) there is no relationship between intuitive reasoning
and organizational improvisation but there is a link between rational
reasoning and organizational improvisation, (b) top level managers-
individual characteristics as a whole affect organizational
improvisation; and (c) organizational improvisation positively affects
firm performance. The theoretical and managerial implications were
discussed in the conclusions.
Abstract: The paper deals with the development of portable aerosol concentrator and its application for the determination of nitrites and nitrates. The device enables the continuous trapping of pollutants in the air. An extensive literature search has been elaborated which aims at the development of samplers and the possibilities of their application in the continuous determination of volatile organic compounds. The practical part of the paper is focused on the development of the portable aerosol concentrator. The device using the Aerosol Enrichment Unit has been experimentally verified and subsequently realized. It operates on the principle of equilibrium accumulation of pollutants from the gaseous phase using absorption liquid polydisperse aerosol. The device has been applied for monitoring nitrites and nitrates in the air. The chemiluminescence detector was used for detection; the achieved detection limit for nitrites was 28 ng/m3 and for nitrates 78 ng/m3.
Abstract: Microscopic emission and fuel consumption models
have been widely recognized as an effective method to quantify real
traffic emission and energy consumption when they are applied with
microscopic traffic simulation models. This paper presents a
framework for developing the Microscopic Emission (HC, CO, NOx,
and CO2) and Fuel consumption (MEF) models for light-duty
vehicles. The variable of composite acceleration is introduced into
the MEF model with the purpose of capturing the effects of historical
accelerations interacting with current speed on emission and fuel
consumption. The MEF model is calibrated by multivariate
least-squares method for two types of light-duty vehicle using
on-board data collected in Beijing, China by a Portable Emission
Measurement System (PEMS). The instantaneous validation results
shows the MEF model performs better with lower Mean Absolute
Percentage Error (MAPE) compared to other two models. Moreover,
the aggregate validation results tells the MEF model produces
reasonable estimations compared to actual measurements with
prediction errors within 12%, 10%, 19%, and 9% for HC, CO, NOx
emissions and fuel consumption, respectively.
Abstract: We propose a phenomenological model for the
process of polymer desorption. In so doing, we omit the usual
theoretical approach of incorporating a fictitious viscoelastic
stress term into the flux equation. As a result, we obtain a
model that captures the essence of the phenomenon of trapping
skinning, while preserving the integrity of the experimentally
verified Fickian law for diffusion. An appropriate asymptotic
analysis is carried out, and a parameter is introduced to represent
the speed of the desorption front. Numerical simulations are
performed to illustrate the desorption dynamics of the model.
Recommendations are made for future modifications of the
model, and provisions are made for the inclusion of experimentally
determined frontal speeds.
Abstract: The porous silicon (PS), formed from the anodization
of a p+ type substrate silicon, consists of a network organized in a
pseudo-column as structure of multiple side ramifications. Structural
micro-topology can be interpreted as the fraction of the interconnected
solid phase contributing to thermal transport. The
reduction of dimensions of silicon of each nanocristallite during the
oxidation induced a reduction in thermal conductivity. Integration of
thermal sensors in the Microsystems silicon requires an effective
insulation of the sensor element. Indeed, the low thermal conductivity
of PS consists in a very promising way in the fabrication of integrated
thermal Microsystems.In this work we are interesting in the
measurements of thermal conductivity (on the surface and in depth)
of PS by the micro-Raman spectroscopy. The thermal conductivity is
studied according to the parameters of anodization (initial doping and
current density. We also, determine porosity of samples by
spectroellipsometry.
Abstract: In this work, the influence of temperature on the
different parameters of solar cells based on organic semiconductors
are studied. The short circuit current Isc increases so monotonous
with temperature and then saturates to a maximum value before
decreasing at high temperatures. The open circuit voltage Vco
decreases linearly with temperature. The fill factor FF and efficiency,
which are directly related with Isc and Vco follow the variations of
the letters. The phenomena are explained by the behaviour of the
mobility which is a temperature activated process.
Abstract: This paper deals with the formulation of Maxwell-s equations in a cavity resonator in the presence of the gravitational field produced by a blackhole. The metric of space-time due to the blackhole is the Schwarzchild metric. Conventionally, this is expressed in spherical polar coordinates. In order to adapt this metric to our problem, we have considered this metric in a small region close to the blackhole and expressed this metric in a cartesian system locally.