Abstract: The object of this paper is to design and analyze a
proportional – integral (PI) control for positive output elementary
super lift Luo converter (POESLLC), which is the start-of-the-art
DC-DC converter. The positive output elementary super lift Luo
converter performs the voltage conversion from positive source
voltage to positive load voltage. This paper proposes a
development of PI control capable of providing the good static and
dynamic performance compared to proportional – integralderivative
(PID) controller. Using state space average method
derives the dynamic equations describing the positive output
elementary super lift luo converter and PI control is designed. The
simulation model of the positive output elementary super lift Luo
converter with its control circuit is implemented in
Matlab/Simulink. The PI control for positive output elementary
super lift Luo converter is tested for transient region, line changes,
load changes, steady state region and also for components
variations.
Abstract: The distribution, enrichment, accumulation, and potential ecological risk of copper (Cu) in the surface sediments of northern Kaohsiung Harbor, Taiwan were investigated. Sediment samples from 12 locations of northern Kaohsiung Harbor were collected and characterized for Cu, aluminum, water content, organic matter, total nitrogen, total phosphorous, total grease and grain size. Results showed that the Cu concentrations varied from 6.9–244 mg/kg with an average of 109±66 mg/kg. The spatial distribution of Cu reveals that the Cu concentration is relatively high in the river mouth region, and gradually diminishes toward the harbor entrance region. This indicates that upstream industrial and municipal wastewater discharges along the river bank are major sources of Cu pollution. Results from the enrichment factor and geo-accumulation index analyses imply that the sediments collected from the river mouth can be characterized between moderate and moderately severe degree enrichment and between none to medium and moderate accumulation of Cu, respectively. However, results of potential ecological risk index indicate that the sediment has low ecological potential risk.
Abstract: In rapidly changing market environment, firms are investing a lot of time and resources into new product development (NPD) projects to make profit and to obtain competitive advantage. However, failure rate of NPD projects is becoming high due to various internal and external risks which hinder successful NPD projects. To reduce the failure rate, it is critical that risks have to be managed effectively and efficiently through good strategy, and treated by optimal responses to minimize risk cost. Four strategies are adopted to handle the risks in this study. The optimal responses are characterized by high reduction of risk costs with high efficiency. This study suggests a framework to decide the optimal responses considering the core risks, risk costs, response efficiency and response costs for successful NPD projects. Both binary particles warm optimization (BPSO) and multi-objective particle swarm optimization (MOPSO) methods are mainly used in the framework. Although several limitations exist in use for real industries, the frame work shows good strength for handling the risks with highly scientific ways through an example.
Abstract: Deniable authentication is a new protocol which not only enables a receiver to identify the source of a received message but also prevents a third party from identifying the source of the message. The proposed protocol in this paper makes use of bilinear pairings over elliptic curves, as well as the Diffie-Hellman key exchange protocol. Besides the security properties shared with previous authentication protocols, the proposed protocol provides the same level of security with smaller public key sizes.
Abstract: The sustainability of a place depends on a series of factors which contribute to the quality of life, sense of place and recognition of identity. An activity like walking, which in itself is obviously ''sustainable'', can become non sustainable if the context in which it is carried out does not meet the conditions for an adequate quality of life. This work is aimed at proposing the analytical method of Place Maker to identify the elements that do not feature in traditional mapping and which constitute the contemporary identity of the places, and the relative complex map to represent those elements and support sustainable urban identity design. The method's potential for areas with a predominantly pedestrian vocation is illustrated by means of the case study of the Ramblas in Barcelona.
Abstract: Cenozoic basalts found in Jiangsu province of eastern
China include tholeiites and alkali basalts. The present paper analyzed
the major, trace elements, rare earth elements of these Cenozoic
basalts and combined with Sr-Nd isotopic compositions proposed by
Chen et al. (1990)[1] in the literatures to discuss the petrogenesis of
these basalts and the geochemical characteristics of the source mantle.
Based on major, trace elements and fractional crystallization model
established by Brooks and Nielsen (1982)[2] we suggest that the
basaltic magma has experienced olivine + clinopyroxene fractionation
during its evolution. The chemical compositions of basaltic rocks from
Jiangsu province indicate that these basalts may belong to the same
magmatic system. Spidergrams reveal that Cenozoic basalts from
Jiangsu province have geochemical characteristics similar to those of
ocean island basalts(OIB). The slight positive Nb and Ti anomalies
found in basaltic rocks of this study suggest the presence of Ti-bearing
minerals in the mantle source and these Ti-bearing minerals had
contributed to basaltic magma during partial melting, indicating a
metasomatic event might have occurred before the partial melting.
Based on the Sr vs. Nd isotopic ratio plots, we suggest that Jiangsu
basalts may be derived from partial melting of mantle source which
may represent two-end members mixing of DMM and EM-I. Some
Jiangsu basaltic magma may be derived from partial melting of EM-I
heated by the upwelling asthenospheric mantle or asthenospheric
diapirism.
Abstract: This paper introduces a hand gesture recognition system to recognize real time gesture in unstrained environments. Efforts should be made to adapt computers to our natural means of communication: Speech and body language. A simple and fast algorithm using orientation histograms will be developed. It will recognize a subset of MAL static hand gestures. A pattern recognition system will be using a transforrn that converts an image into a feature vector, which will be compared with the feature vectors of a training set of gestures. The final system will be Perceptron implementation in MATLAB. This paper includes experiments of 33 hand postures and discusses the results. Experiments shows that the system can achieve a 90% recognition average rate and is suitable for real time applications.
Abstract: Quality Function Deployment (QFD) is an expounded, multi-step planning method for delivering commodity, services, and processes to customers, both external and internal to an organization. It is a way to convert between the diverse customer languages expressing demands (Voice of the Customer), and the organization-s languages expressing results that sate those demands. The policy is to establish one or more matrices that inter-relate producer and consumer reciprocal expectations. Due to its visual presence is called the “House of Quality" (HOQ). In this paper, we assumed HOQ in multi attribute decision making (MADM) pattern and through a proposed MADM method, rank technical specifications. Thereafter compute satisfaction degree of customer requirements and for it, we apply vagueness and uncertainty conditions in decision making by fuzzy set theory. This approach would propound supervised neural network (perceptron) for MADM problem solving.
Abstract: Gene, principal unit of inheritance, is an ordered
sequence of nucleotides. The genes of eukaryotic organisms include
alternating segments of exons and introns. The region of
Deoxyribonucleic acid (DNA) within a gene containing instructions
for coding a protein is called exon. On the other hand, non-coding
regions called introns are another part of DNA that regulates gene
expression by removing from the messenger Ribonucleic acid (RNA)
in a splicing process. This paper proposes to determine splice
junctions that are exon-intron boundaries by analyzing DNA
sequences. A splice junction can be either exon-intron (EI) or intron
exon (IE). Because of the popularity and compatibility of the
artificial neural network (ANN) in genetic fields; various ANN
models are applied in this research. Multi-layer Perceptron (MLP),
Radial Basis Function (RBF) and Generalized Regression Neural
Networks (GRNN) are used to analyze and detect the splice junctions
of gene sequences. 10-fold cross validation is used to demonstrate
the accuracy of networks. The real performances of these networks
are found by applying Receiver Operating Characteristic (ROC)
analysis.
Abstract: Carbon nanotubes (CNTs) with their high mechanical,
electrical, thermal and chemical properties are regarded as promising
materials for many different potential applications. Having unique
properties they can be used in a wide range of fields such as
electronic devices, electrodes, drug delivery systems, hydrogen
storage, textile etc. Catalytic chemical vapor deposition (CCVD) is a
common method for CNT production especially for mass production.
Catalysts impregnated on a suitable substrate are important for
production with chemical vapor deposition (CVD) method. Iron
catalyst and MgO substrate is one of most common catalyst-substrate
combination used for CNT. In this study, CNTs were produced by
CCVD of acetylene (C2H2) on magnesium oxide (MgO) powder
substrate impregnated by iron nitrate (Fe(NO3)3•9H2O) solution. The
CNT synthesis conditions were as follows: at synthesis temperatures
of 500 and 800°C multiwall and single wall CNTs were produced
respectively. Iron (Fe) catalysts were prepared by with Fe:MgO ratio
of 1:100, 5:100 and 10:100. The duration of syntheses were 30 and
60 minutes for all temperatures and catalyst percentages. The
synthesized materials were characterized by thermal gravimetric
analysis (TGA), transmission electron microscopy (TEM) and Raman
spectroscopy.
Abstract: The aim of present experiment was to evaluate the
influence of cultivar to quality parameters of dried potato chips and
sticks produced in microwave-vacuum drier. The potatoes before
drying were blanched in oil and water at 180ºC and at 85ºC
respectively. The moisture content, crispiness, the colour (CIE
L*a*b*), the content of ascorbic acid, total carotenoids and total fat
content of dried potato chips and sticks was determined The highest
ascorbic acid content, high content of carotenoids, low total fat
content, low acrylamide content and good crispiness (low breaking
force) especially for sticks was determined in the samples of Gundega
cultivar.
Abstract: This article experimentally investigates the
thermal performance of thermoelectric air-cooling module
which comprises a thermoelectric cooler (TEC) and an
air-cooling heat sink. The influences of input current and heat
load are determined. And performances under each situation
are quantified by thermal resistance analysis. Since TEC
generates Joule heat, this nature makes construction of thermal
resistance network difficult. To simplify the analysis, this
article emphasizes on the resistance heat load might meet when
passing through the device. Therefore, the thermal resistances
in this paper are to divide temperature differences by heat load.
According to the result, there exists an optimum input current
under every heating power. In this case, the optimum input
current is around 6A or 7A. The performance of the heat sink
would be improved with TEC under certain heating power and
input current, especially at a low heat load. According to the
result, the device can even make the heat source cooler than the
ambient. However, TEC is not always effective at every heat
load and input current. In some situation, the device works
worse than the heat sink without TEC. To determine the
availability of TEC, this study figures out the effective
operating region in which the TEC air-cooling module works
better than the heat sink without TEC. The result shows that
TEC is more effective at a lower heat load. If heat load is too
high, heat sink with TEC will perform worse than without TEC.
The limit of this device is 57W. Besides, TEC is not helpful if
input current is too high or too low. There is an effective range
of input current, and the range becomes narrower when the heat
load grows.
Abstract: The algorithm represents the DCT coefficients to concentrate signal energy and proposes combination and dictator to eliminate the correlation in the same level subband for encoding the DCT-based images. This work adopts DCT and modifies the SPIHT algorithm to encode DCT coefficients. The proposed algorithm also provides the enhancement function in low bit rate in order to improve the perceptual quality. Experimental results indicate that the proposed technique improves the quality of the reconstructed image in terms of both PSNR and the perceptual results close to JPEG2000 at the same bit rate.
Abstract: Twist drills are geometrical complex tools and thus various researchers have adopted different mathematical and experimental approaches for their simulation. The present paper acknowledges the increasing use of modern CAD systems and using the API (Application Programming Interface) of a CAD system, drilling simulations are carried out. The developed DRILL3D software routine, creates parametrically controlled tool geometries and using different cutting conditions, achieves the generation of solid models for all the relevant data involved (drilling tool, cut workpiece, undeformed chip). The final data derived, consist a platform for further direct simulations regarding the determination of cutting forces, tool wear, drilling optimizations etc.
Abstract: This paper presents an interval-based multi-attribute
decision making (MADM) approach in support of the decision
process with imprecise information. The proposed decision
methodology is based on the model of linear additive utility function
but extends the problem formulation with the measure of composite
utility variance. A sample study concerning with the evaluation of
electric generation expansion strategies is provided showing how the
imprecise data may affect the choice toward the best solution and
how a set of alternatives, acceptable to the decision maker (DM),
may be identified with certain confidence.
Abstract: The aim of the paper is based on detailed analysis of
literary sources and carried out research to develop a model
development and implementation of innovation strategy in the
business. The paper brings the main results of the authors conducted
research on a sample of 462 respondents that shows the current
situation in the Slovak enterprises in the use of innovation strategy.
Carried out research and analysis provided the base for a model
development and implementation of innovation strategy in the
business, which is in the paper in detail, step by step explained with
emphasis on the implementation process. Implementing the
innovation strategy is described a separate model. Paper contains
recommendations for successful implementation of innovation
strategy in the business. These recommendations should serve mainly
business managers as valuable tool in implementing the innovation
strategy.
Abstract: Available Bit Rate Service (ABR) is the lower priority
service and the better service for the transmission of data. On wireline
ATM networks ABR source is always getting the feedback from
switches about increase or decrease of bandwidth according to the
changing network conditions and minimum bandwidth is guaranteed.
In wireless networks guaranteeing the minimum bandwidth is really a
challenging task as the source is always in mobile and traveling from
one cell to another cell. Re establishment of virtual circuits from start
to end every time causes the delay in transmission. In our proposed
solution we proposed the mechanism to provide more available
bandwidth to the ABR source by re-usage of part of old Virtual
Channels and establishing the new ones. We want the ABR source to
transmit the data continuously (non-stop) inorderto avoid the delay.
In worst case scenario at least minimum bandwidth is to be allocated.
In order to keep the data flow continuously, priority is given to the
handoff ABR call against new ABR call.
Abstract: This paper presents the experimental results of a
single cylinder Enfield engine using an electronically controlled fuel
injection system which was developed to carry out exhaustive tests
using neat CNG, and mixtures of hydrogen in compressed natural gas
(HCNG) as 0, 5, 10, 15 and 20% by energy. Experiments were
performed at 2000 and 2400 rpm with wide open throttle and varying
the equivalence ratio. Hydrogen which has fast burning rate, when
added to compressed natural gas, enhances its flame propagation rate.
The emissions of HC, CO, decreased with increasing percentage of
hydrogen but NOx was found to increase. The results indicated a
marked improvement in the brake thermal efficiency with the
increase in percentage of hydrogen added. The improved thermal
efficiency was clearly observed to be more in lean region as
compared to rich region. This study is expected to reduce vehicular
emissions along with increase in thermal efficiency and thus help in
reduction of further environmental degradation.
Abstract: In this article we are going to discuss the improvement
of the multi classes- classification problem using multi layer
Perceptron. The considered approach consists in breaking down the
n-class problem into two-classes- subproblems. The training of each
two-class subproblem is made independently; as for the phase of test,
we are going to confront a vector that we want to classify to all two
classes- models, the elected class will be the strongest one that won-t
lose any competition with the other classes. Rates of recognition
gotten with the multi class-s approach by two-class-s decomposition
are clearly better that those gotten by the simple multi class-s
approach.
Abstract: PARADIGMA (PARticipative Approach to DIsease
Global Management) is a pilot project which aims to develop and
demonstrate an Internet based reference framework to share scientific
resources and findings in the treatment of major diseases.
PARADIGMA defines and disseminates a common methodology and
optimised protocols (Clinical Pathways) to support service functions
directed to patients and individuals on matters like prevention, posthospitalisation
support and awareness. PARADIGMA will provide a
platform of information services - user oriented and optimised
against social, cultural and technological constraints - supporting the
Health Care Global System of the Euro-Mediterranean Community
in a continuous improvement process.