Abstract: In this paper, we study the optical nonlinearities of
Silver sulfide (Ag2S) nanostructures dispersed in the Dimethyl
sulfoxide (DMSO) under exposure to 532 nm, 15 nanosecond (ns)
pulsed laser irradiation. Ultraviolet–visible absorption spectrometry
(UV-Vis), X-ray diffraction (XRD), and transmission electron
microscopy (TEM) are used to characterize the obtained nanocrystal
samples. The band gap energy of colloid is determined by analyzing
the UV–Vis absorption spectra of the Ag2S NPs using the band
theory of semiconductors. Z-scan technique is used to characterize
the optical nonlinear properties of the Ag2S nanoparticles (NPs).
Large enhancement of two photon absorption effect is observed with
increase in concentration of the Ag2S nanoparticles using open Zscan
measurements in the ns laser regime. The values of the nonlinear
absorption coefficients are determined based on the local nonlinear
responses including two photon absorption. The observed aperture
dependence of the Ag2S NP limiting performance indicates that the
nonlinear scattering plays an important role in the limiting action of
the sample. The concentration dependence of the optical liming is
also investigated. Our results demonstrate that the optical limiting
threshold decreases with increasing the silver sulfide NPs in DMSO.
Abstract: Nowadays, energy dissipation devices are commonly
used in structures. High rate of energy absorption during earthquakes
is the benefit of using such devices, which results in damage
reduction of structural elements, specifically columns. The hysteretic
damping capacity of energy dissipation devices is the key point that it
may adversely make analysis and design process complicated. This
effect may be generally represented by Equivalent Viscous Damping
(EVD). The equivalent viscous damping might be obtained from the
expected hysteretic behavior regarding to the design or maximum
considered displacement of a structure. In this paper, the hysteretic
damping coefficient of a steel Moment Resisting Frame (MRF),
which its performance is enhanced by a Buckling Restrained Brace
(BRB) system has been evaluated. Having foresight of damping
fraction between BRB and MRF is inevitable for seismic design
procedures like Direct Displacement-Based Design (DDBD) method.
This paper presents an approach to calculate the damping fraction for
such systems by carrying out the dynamic nonlinear time history
analysis (NTHA) under harmonic loading, which is tuned to the
natural system frequency. Two MRF structures, one equipped with
BRB and the other without BRB are simultaneously studied.
Extensive analysis shows that proportion of each system damping
fraction may be calculated by its shear story portion. In this way,
contribution of each BRB in the floors and their general contribution
in the structural performance may be clearly recognized, in advance.
Abstract: This paper presents the influence of the vertical
seismic component on the non-linear dynamics analysis of three
different structures. The subject structures were analyzed and
designed according to recent codes. This paper considers three types
of buildings: 5-, 10-, and 15-story buildings. The non-linear dynamics
analysis of the structures with assuming elastic-perfectly-plastic
behavior was performed using RAM PERFORM-3D software; the
horizontal component was taken into consideration with and without
the incorporation of the corresponding vertical component. Dynamic
responses obtained for the horizontal component acting alone were
compared with those obtained from the simultaneous application of
both seismic components. The results show that the effect of the
vertical component of ground motion may increase the axial load
significantly in the interior columns and, consequently, the stories.
The plastic mechanisms would be changed. The P-Delta effect is
expected to increase. The punching base plate shear of the columns
should be considered. Moreover, the vertical component increases the
input energy when the structures exhibit inelastic behavior and are
taller.
Abstract: Fiber Reinforced Polymer (FRP) is a composite material with exceptional properties that are capable to replace conventional steel reinforcement in reinforced and pre-stressed concrete structures. However, the main obstacle for their wide use in pre-stressed concrete application is the anchorage system. Due to the weakness of FRP in the transverse direction, the pre-stressing capacity of FRP bars are limited. This paper investigates the modification of the conventional wedge anchorage system to be used for stressing of FRP bars in pre-stressed applications. Epoxy adhesive material with glass FRP (GFRP) bars and conventional steel wedge were used in this paper. The GFRP bars are encased with epoxy at the anchor zone and the wedge system was used in pull-out test. The results showed a loading capacity of 47.6 kN which is 69% of the bar ultimate capacity. Additionally, nylon wedge was made with the same dimensions of the steel wedge and tested for GFRP bars without epoxy layer. The nylon wedge showed a loading capacity of 19.7 kN which is only 28.5% of the ultimate bar capacity.
Abstract: Passive control methods can be utilized to build
earthquake resistant structures, and also to strengthen the vulnerable
ones. In this paper, we studied the effect of this system in increasing
the ductility and energy dissipation and also modeled the behavior of
this type of eccentric bracing, and compared the hysteresis diagram
of the modeled samples with the laboratory samples. We studied
several samples of frames with vertical shear-links in order to assess
the behavior of this type of eccentric bracing. Each of these samples
was modeled in finite element software ANSYS 9.0, and was
analyzed under the static cyclic loading. It was found that vertical
shear-links have a more stable hysteresis loops. Another analysis
showed that using honeycomb beams as the horizontal beam along
with steel reinforcement has no negative effect on the hysteresis
behavior of the sample.
Abstract: Investigating the dynamic responses of high rise
structures under the effect of siesmic ground motion is extremely
important for the proper analysis and design of multitoried structures.
Since the presence of infilled walls strongly influences the behaviour
of frame systems in multistoried buildings, there is an increased need
for developing guidelines for the analysis and design of infilled
frames under the effect of dynamic loads for safe and proper design
of buildings. In this manuscript, we evaluate the natural frequencies
and natural periods of single bay single storey frames considering the
effect of infill walls by using the Eigen value analysis and validating
with SAP 2000 (free vibration analysis). Various parameters obtained
from the diagonal strut model followed for the free vibration analysis
is then compared with the Finite Element model, where infill is
modeled as shell elements (four noded). We also evaluated the effect
of various parameters on the natural periods of vibration obtained by
free vibration analysis in SAP 2000 comparing them with those
obtained by the empirical expressions presented in I.S. 1893(Part I)-
2002.
Abstract: Concrete is strong in compression however weak in
tension. The tensile strength as well as ductile property of concrete
could be improved by addition of short dispersed fibers. Polyethylene
terephthalate (PET) fiber obtained from hand cutting or mechanical
slitting of plastic sheets generally used as discrete reinforcement in
substitution of steel fiber. PET fiber obtained from the former process
is in the form of straight slit sheet pattern that impart weaker
mechanical bonding behavior in the concrete matrix. To improve the
limitation of straight slit sheet fiber the present study considered two
additional geometry of fiber namely (a) flattened end slit sheet and
(b) deformed slit sheet. The mix for plain concrete was design for a
compressive strength of 25 MPa at 28 days curing time with a watercement
ratio of 0.5. Cylindrical and beam specimens with 0.5% fibers
volume fraction and without fibers were cast to investigate the
influence of geometry on the mechanical properties of concrete. The
performance parameters mainly studied include flexural strength,
splitting tensile strength, compressive strength and ultrasonic pulse
velocity (UPV). Test results show that geometry of fiber has a
marginal effect on the workability of concrete. However, it plays a
significant role in achieving a good compressive and tensile strength
of concrete. Further, significant improvement in term of flexural and
energy dissipation capacity were observed from other fibers as
compared to the straight slit sheet pattern. Also, the inclusion of PET
fiber improved the ability in absorbing energy in the post-cracking
state of the specimen as well as no significant porous structures.
Abstract: Twin steel plates-concrete composite shear walls are
composed of a pair of steel plate layers and a concrete layer
sandwiched between them, which have the characteristics of both
reinforced concrete shear walls and steel plate shear walls. Twin steel
plates-composite shear walls contain very high ultimsate bearing
capacity and ductility, which have great potential to be applied in the
super high-rise buildings and special structures. In this paper, we
analyzed the basic characteristics and stress mechanism of the twin
steel plates-composite shear walls. Specifically, we analyzed the
effects of the steel plate thickness, wall thickness and concrete
strength on the bearing capacity of the twin steel plates-composite
shear walls. The analysis results indicate that: (1) the initial shear
stiffness and ultimate shear-carrying capacity is not significantly
affected by the thickness of concrete wall but by the class of concrete,
(2) both factors significantly impact the shear distribution of the
shear walls in ultimate shear-carrying capacity. The technique of twin
steel plates-composite shear walls has been successfully applied in
the construction of an 88-meter Huge Statue of Buddha located in
Hunan Province, China. The analysis results and engineering
experiences showed that the twin steel plates-composite shear walls
have great potential for future research and applications.
Abstract: This research paper presents the current practices of
teacher professional development, perceived as beneficial by teachers
themselves, in a private secondary school in Brunei Darussalam. This
is part of the findings of a larger qualitative study on teacher
empowerment, using ethnographic methods for data collection, i.e.
participant observation, interviews and document analysis. The field
work was carried out over a period of six months in 2013. An
analysis of the field data revealed multiple pathways of teacher
professional development existing in the school. The results indicate
that school leaders, the teacher community in the school, students,
and the teachers themselves were the agents in a school that
facilitated teacher empowerment. Besides contributing to the
knowledge base on teacher professional development, the results of
this study provide directions for educational policy makers in their
efforts to enhance professional development in secondary schools of
similar characteristics. For school leaders and the teacher community,
these findings offer guidelines for maximizing the opportunities for
these professional development practices, by strengthening
collegiality and by using the existing structures optimally for the
benefit of all concerned.
Abstract: Expansive soils are often encountered in many parts
of the world, especially in arid and semi-arid fields. Such kind of
soils, generally including active clay minerals in low water content,
enlarge in volume by absorbing the water through the surface and
cause a great harm to the light structures such as channel coating,
roads and airports. The expansive soils were encountered on the path
of Apa-Hotamış conveyance channel belonging to the State
Hydraulic Works in the region of Konya. In the research done in this
area, it is predicted that the soil has a swollen nature and the soil
should be filled with proper granular equipments by digging the
ground to 50-60 cm. In this study, for purpose of helping the other
research to be done in the same area, it is thought that instead of
replacing swollen soil with the granular soil, by stabilizing it with
polypropylene fiber and using it its original place decreases effect of
swelling percent, in this way the cost will be decreased. Therefore,
laboratory tests were conducted to study the effects of polypropylene
fiber on swelling characteristics of expansive soil. Test results
indicated that inclusion of fiber reduced swell percent of expansive
soil. As the fiber content increased, the unconfined compressive
strength was increased. Finally, it can be said that stabilization of
expansive soils with polypropylene fiber is an effective method.
Abstract: This paper presents a fully Lagrangian coupled
Fluid-Structure Interaction (FSI) solver for simulations of
fluid-structure interactions, which is based on the Moving Particle
Semi-implicit (MPS) method to solve the governing equations
corresponding to incompressible flows as well as elastic structures.
The developed solver is verified by reproducing the high velocity
impact loads of deformable thin wedges with three different materials
such as mild steel, aluminium and tin during water entry. The present
simulation results for aluminium are compared with analytical solution
derived from the hydrodynamic Wagner model and linear Wan’s
theory. And also, the impact pressure and strain on the water entry
wedge with three different materials, such as mild steel, aluminium
and tin, are simulated and the effects of hydro-elasticity are discussed.
Abstract: The objective of this paper is to evaluate the effects of
soil-structure interaction (SSI) on the modal characteristics and on
the dynamic response of current structures. The objective is on the
overall behaviour of a real structure of five storeys reinforced
concrete (R/C) building typically encountered in Algeria. Sensitivity
studies are undertaken in order to study the effects of frequency
content of the input motion, frequency of the soil-structure system,
rigidity and depth of the soil layer on the dynamic response of such
structures. This investigation indicated that the rigidity of the soil
layer is the predominant factor in soil-structure interaction and its
increases would definitely reduce the deformation in the R/C
structure. On the other hand, increasing the period of the underlying
soil will cause an increase in the lateral displacements at story levels
and create irregularity in the distribution of story shears. Possible
resonance between the frequency content of the input motion and soil
could also play an important role in increasing the structural
response.
Abstract: This paper deals with nonlinear vibration analysis
using finite element method for frame structures consisting of elastic
and viscoelastic damping layers supported by multiple nonlinear
concentrated springs with hysteresis damping. The frame is supported
by four nonlinear concentrated springs near the four corners. The
restoring forces of the springs have cubic non-linearity and linear
component of the nonlinear springs has complex quantity to represent
linear hysteresis damping. The damping layer of the frame structures
has complex modulus of elasticity. Further, the discretized equations in
physical coordinate are transformed into the nonlinear ordinary
coupled differential equations using normal coordinate corresponding
to linear natural modes. Comparing shares of strain energy of the
elastic frame, the damping layer and the springs, we evaluate the
influences of the damping couplings on the linear and nonlinear impact
responses. We also investigate influences of damping changed by
stiffness of the elastic frame on the nonlinear coupling in the damped
impact responses.
Abstract: In addition to the advantages of light weight, resistant
corrosion and ease of processing, aluminum is also applied to the
long-span spatial structures. However, the elastic modulus of
aluminum is lower than that of the steel. This paper combines the
high performance aluminum honeycomb panel with the aluminum
latticed shell, forming a new panel-and-rod composite shell structure.
Through comparative analysis between the static and dynamic
performance, the conclusion that the structure of composite shell is
noticeably superior to the structure combined before.
Abstract: Structure-borne noise is an important aspect of
offshore platform sound field. It can be generated either directly by
vibrating machineries induced mechanical force, indirectly by the
excitation of structure or excitation by incident airborne noise.
Therefore, limiting of the transmission of vibration energy
throughout the offshore platform is the key to control the structureborne
noise. This is usually done by introducing damping treatment
to the steel structures. Two types of damping treatment using onboard
are presented. By conducting a Statistical Energy Analysis
(SEA) simulation on a jack-up rig, the noise level in the source room,
the neighboring rooms, and remote living quarter cabins are
compared before and after the damping treatments been applied. The
results demonstrated that, in the source neighboring room and living
quarter area, there is a significant noise reduction with the damping
treatment applied, whereas in the source room where air-borne sound
predominates that of structure-borne sound, the impact is not
obvious. The conclusion on effective damping treatment in the
offshore platform is made which enable acoustic professionals to
implement noise control during the design stage for offshore crews’
hearing protection and habitant comfortability.
Abstract: In the present study, the properties of Al-Al2O3
nanocomposite hollow sphere structures were investigated. For this
reason, the Al-based nanocomposite hollow spheres with different
amounts of nano-alumina reinforcement (0-10wt %) and different
ratio of thickness to diameter (t/D: 0.06-0.3) were prepared via a
powder metallurgy method. Then, the effect of mentioned parameters
was studied on physical and quasi static mechanical properties of
their related prepared structures (open/closed cell) such as density,
hardness, strength, and energy absorption. It was found that, as the
t/D ratio increases the relative density, compressive strength and
energy absorption increase. The highest values of strength and energy
absorption were obtained from the specimen with 5 wt. % of
nanoparticle reinforcement, t/D of 0.3 (t=1 mm, D=400μm) as 22.88
MPa and 13.24 MJ/m3, respectively. The moderate specific strength
of prepared composites in the present study showed the good
consistency with the properties of others low carbon steel composite
with similar structure.
Abstract: Drying is a phenomenon that accompanies the
hardening of hydraulic materials. This study is concerned the
modelling of drying shrinkage of the hydraulic materials and the
prediction of the rate of spontaneous deformations of hydraulic
materials during hardening. The model developed takes consideration
of the main factors affecting drying shrinkage. There was agreement
between drying shrinkage predicted by the developed model and
experimental results. In last we show that developed model describe
the evolution of the drying shrinkage of high performances concretes
correctly.
Abstract: This paper presents thermal annealing de-wetting
technique for the preparation of porous metal membrane for Thin
Film Encapsulation (TFE) application. Thermal annealing de-wetting
experimental results reveal that pore size formation in porous metal
membrane depend upon i.e. 1. The substrate at which metal is
deposited, 2. Melting point of metal used for porous metal cap layer
membrane formation, 3. Thickness of metal used for cap layer, 4.
Temperature used for formation of porous metal membrane. In order
to demonstrate this technique, Silver (Ag) was used as a metal for
preparation of porous metal membrane on amorphous silicon (a-Si)
and silicon oxide. The annealing of the silver thin film of various
thicknesses was performed at different temperature. Pores in porous
silver film were analyzed using Scanning Electron Microscope
(SEM). In order to check the usefulness of porous metal film for TFE
application, the porous silver film prepared on amorphous silicon (a-
Si) and silicon oxide was released using XeF2 and VHF, respectively.
Finally, guide line and structures are suggested to use this porous
membrane for robust TFE application.
Abstract: Typical load-bearing biological materials like bone,
mineralized tendon and shell, are biocomposites made from both
organic (collagen) and inorganic (biomineral) materials. This
amazing class of materials with intrinsic internally designed
hierarchical structures show superior mechanical properties with
regard to their weak components from which they are formed.
Extensive investigations concentrating on static loading conditions
have been done to study the biological materials failure. However,
most of the damage and failure mechanisms in load-bearing
biological materials will occur whenever their structures are exposed
to dynamic loading conditions. The main question needed to be
answered here is: What is the relation between the layout and
architecture of the load-bearing biological materials and their
dynamic behavior? In this work, a staggered model has been
developed based on the structure of natural materials at nanoscale and
Finite Element Analysis (FEA) has been used to study the dynamic
behavior of the structure of load-bearing biological materials to
answer why the staggered arrangement has been selected by nature to
make the nanocomposite structure of most of the biological materials.
The results showed that the staggered structures will efficiently
attenuate the stress wave rather than the layered structure.
Furthermore, such staggered architecture is effectively in charge of
utilizing the capacity of the biostructure to resist both normal and
shear loads. In this work, the geometrical parameters of the model
like the thickness and aspect ratio of the mineral inclusions selected
from the typical range of the experimentally observed feature sizes
and layout dimensions of the biological materials such as bone and
mineralized tendon. Furthermore, the numerical results validated with
existing theoretical solutions. Findings of the present work emphasize
on the significant effects of dynamic behavior on the natural
evolution of load-bearing biological materials and can help scientists
to design bioinspired materials in the laboratories.
Abstract: In recent years, honeycomb fiber reinforced plastic
(FRP) sandwich panels have been increasingly used in various
industries. Low weight, low price and high mechanical strength are
the benefits of these structures. However, their mechanical properties
and behavior have not been fully explored. The objective of this
study is to conduct a combined numerical-statistical investigation of
honeycomb FRP sandwich beams subject to torsion load. In this
paper, the effect of geometric parameters of sandwich panel on
maximum shear strain in both face and core and angle of torsion in a
honeycomb FRP sandwich structures in torsion is investigated. The
effect of Parameters including core thickness, face skin thickness,
cell shape, cell size, and cell thickness on mechanical behavior of the
structure were numerically investigated. Main effects of factors were
considered in this paper and regression equations were derived.
Taguchi method was employed as experimental design and an
optimum parameter combination for the maximum structure stiffness
has been obtained. The results showed that cell size and face skin
thickness have the most significant impacts on torsion angle,
maximum shear strain in face and core.