Abstract: Gas hydrates can agglomerate and block multiphase oil and gas pipelines when water is present at hydrate forming conditions. Using "Cold Flow Technology", the aim is to condition gas hydrates so that they can be transported as a slurry mixture without a risk of agglomeration. During the pipeline shut down however, hydrate particles may settle in bends and build hydrate plugs. An experimental setup has been designed and constructed to study the flow of such plugs at start up operations. Experiments have been performed using model fluid and model hydrate particles. The propagations of initial plugs in a bend were recorded with impedance probes along the pipe. The experimental results show a dispersion of the plug front. A peak in pressure drop was also recorded when the plugs were passing the bend. The evolutions of the plugs have been simulated by numerical integration of the incompressible mass balance equations, with an imposed mixture velocity. The slip between particles and carrier fluid has been calculated using a drag relation together with a particle-fluid force balance.
Abstract: Compacted clay liners (CCLs) are the main materials
used in waste disposal landfills due to their low permeability. In this
study, the effect on the shear resistant of clays with inorganic salt
solutions as permeate fluid was experimentally investigated. For this
purpose, NaCl inorganic salt solution at concentrations of 2, 5, 10%
and deionized water were used. Laboratory direct shear and Vane
shear tests were conducted on three compacted clays with low,
medium and high plasticity. Results indicated that the solutions type
and its concentration affect the shear properties of the mixture. In the
light of this study, the influence magnitude of these inorganic salts in
varies concentrations in different clays were determined and more
suitable compacted clay with the compare of plasticity were found.
Abstract: In this paper, the signal transmission analysis of the
semicircle-shaped via structure for the differential pairs is presented in
the frequency range up to 10 GHz. In order to improve the signal
transmission properties in the differential pairs, single via is separated
centrally into two semicircle-shaped sections, which are
interconnected with the traces of differential pairs respectively. This
via structure make possible to route differential pairs using only one
via. In addition, it can improve impedance discontinuity around its
region and then enhance the signal transmission properties in the
differential pairs. The electrical analysis such as S-parameter
calculation and eye diagram simulation has been performed to
investigate the improvement of the signal transmission property in the
differential pairs with new via structure.
Abstract: Validation of an automation system is an important issue. The goal is to check if the system under investigation, modeled by a Petri net, never enters the undesired states. Usually, tools dedicated to Petri nets such as DESIGN/CPN are used to make reachability analysis. The biggest problem with this approach is that it is impossible to generate the full occurence graph of the system because it is too large. In this paper, we show how computational methods such as temporal logic model checking and Groebner bases can be used to verify the correctness of the design of an automation system. We report our experimental results with two automation systems: the Automated Guided Vehicle (AGV) system and the traffic light system. Validation of these two systems ranged from 10 to 30 seconds on a PC depending on the optimizing parameters.
Abstract: Natural resources management including water resources requires reliable estimations of time variant environmental parameters. Small improvements in the estimation of environmental parameters would result in grate effects on managing decisions. Noise reduction using wavelet techniques is an effective approach for preprocessing of practical data sets. Predictability enhancement of the river flow time series are assessed using fractal approaches before and after applying wavelet based preprocessing. Time series correlation and persistency, the minimum sufficient length for training the predicting model and the maximum valid length of predictions were also investigated through a fractal assessment.
Abstract: Recently, Cassava has been the driving force of many
developing countries- economic progress. To attain this level,
prerequisites were put in place enabling cassava sector to become an
industrial and a highly competitive crop. Cameroon can achieve the
same results. Moreover, it can upgrade the living conditions of both
rural and urban dwellers and stimulate the development of the whole
economy. Achieving this outcome calls for agricultural policy
reforms. The adoption and implementation of adequate policies go
along with efficient strategies. To choose effective strategies, an indepth
investigation of the sector-s problems is highly recommended.
This paper uses gap analysis method to evaluate cassava sector in
Cameroon. It studies the present situation (where it is now),
interrogates the future (where it should be) and finally proposes
solutions to fill the gap.
Abstract: Modeling of Panel Zone (PZ) seismic behavior,
because of its role in overall ductility and lateral stiffness of steel
moment frames, has been considered a challenge for years. There are
some studies regarding the effects of different doubler plates
thicknesses and geometric properties of PZ on its seismic behavior.
However, there is not much investigation on the effects of number of
provided continuity plates in case of presence of one triangular
haunch, two triangular haunches and rectangular haunch (T shape
haunches) for exterior columns. In this research first detailed finite
element models of 12tested connection of SAC joint venture were
created and analyzed then obtained cyclic behavior backbone curves
of these models besides other FE models for similar tests were used
for neural network training. Then seismic behavior of these data is
categorized according to continuity plate-s arrangements and
differences in type of haunches. PZ with one-sided haunches have
little plastic rotation. As the number of continuity plates increases
due to presence of two triangular haunches (four continuity plate),
there will be no plastic rotation, in other words PZ behaves in its
elastic range. In the case of rectangular haunch, PZ show more plastic
rotation in comparison with one-sided triangular haunch and
especially double-sided triangular haunches. Moreover, the models
that will be presented in case of triangular one-sided and double-
sided haunches and rectangular haunches as a result of this study
seem to have a proper estimation of PZ seismic behavior.
Abstract: Single biometric modality recognition is not able to meet the high performance supplies in most cases with its application become more and more broadly. Multimodal biometrics identification represents an emerging trend recently. This paper investigates a novel algorithm based on fusion of both fingerprint and fingervein biometrics. For both biometric recognition, we employ the Monogenic Local Binary Pattern (MonoLBP). This operator integrate the orginal LBP (Local Binary Pattern ) with both other rotation invariant measures: local phase and local surface type. Experimental results confirm that a weighted sum based proposed fusion achieves excellent identification performances opposite unimodal biometric systems. The AUC of proposed approach based on combining the two modalities has very close to unity (0.93).
Abstract: Combined experimental and computational analysis of
hygrothermal performance of an interior thermal insulation system
applied on a brick wall is presented in the paper. In the experimental
part, the functionality of the insulation system is tested at simulated
difference climate conditions using a semi-scale device. The
measured temperature and relative humidity profiles are used for the
calibration of computer code HEMOT that is finally applied for a
long-term hygrothermal analysis of the investigated structure.
Abstract: The structural stability of the model of a nonelectroneutral current sheath is investigated. The stationary model of a current sheath represents the system of four connected nonlinear differential first-order equations and thus they should manifest structural instability property, i.e. sensitivity to the infinitesimal changes of parameters and starting conditions. Domains of existence of the solutions of current sheath type are found. Those solutions of the current sheath type are realized only in some regions of sevendimensional space of parameters of the problem. The phase volume of those regions is small in comparison with the whole phase volume of the definition range of those parameters. It is shown that the offered model of a nonelectroneutral current sheath is applicable for theoretical interpretation of the bifurcational current sheaths observed in the magnetosphere.
Abstract: It is sometimes difficult to differentiate between
innocent murmurs and pathological murmurs during auscultation. In
these difficult cases, an intelligent stethoscope with decision support
abilities would be of great value. In this study, using a dog model,
phonocardiographic recordings were obtained from 27 boxer dogs
with various degrees of aortic stenosis (AS) severity. As a reference
for severity assessment, continuous wave Doppler was used. The data
were analyzed with recurrence quantification analysis (RQA) with
the aim to find features able to distinguish innocent murmurs from
murmurs caused by AS. Four out of eight investigated RQA features
showed significant differences between innocent murmurs and
pathological murmurs. Using a plain linear discriminant analysis
classifier, the best pair of features (recurrence rate and entropy)
resulted in a sensitivity of 90% and a specificity of 88%. In
conclusion, RQA provide valid features which can be used for
differentiation between innocent murmurs and murmurs caused by
AS.
Abstract: Wireless ad hoc nodes are freely and dynamically
self-organize in communicating with others. Each node can act as
host or router. However it actually depends on the capability of
nodes in terms of its current power level, signal strength, number
of hops, routing protocol, interference and others. In this research,
a study was conducted to observe the effect of hops count over
different network topologies that contribute to TCP Congestion
Control performance degradation. To achieve this objective, a
simulation using NS-2 with different topologies have been
evaluated. The comparative analysis has been discussed based on
standard observation metrics: throughput, delay and packet loss
ratio. As a result, there is a relationship between types of topology
and hops counts towards the performance of ad hoc network. In
future, the extension study will be carried out to investigate the
effect of different error rate and background traffic over same
topologies.
Abstract: In this study, the thermal and mechanical properties of
basalt fibre reinforced concrete were investigated. The volume
fractions of basalt fibre of (0.1, 0.2, 0.3, and 0.5% by total mix
volume) were used. Properties such as heat transfer, compressive and
splitting tensile strengths were examined. Results indicated that the
strength increases with increase the fibre content till 0.3% then there
is a slight reduction when 0.5% fibre used. Lower amount of heat
conducted through the thickness of concrete specimens than the
conventional concrete was also recorded.
Abstract: Unified Theory of Acceptance and Use of Technology
(UTAUT) model has demonstrated the influencing factors for generic
information systems use such as tablet personal computer (TPC) and
mobile communication. However, in the context of digital library
system, there has been very little effort to determine factors affecting
the intention to use digital library based on the UTAUT model. This
paper investigates factors that are expected to influence the intention
of postgraduate students to use digital library based on modified
UTAUT model. The modified model comprises of constructs
represented by several latent variables, namely performance
expectancy (PE), effort expectancy (EE), information quality (IQ)
and service quality (SQ) and moderated by age, gender and
experience in using digital library. Results show that performance
expectancy, effort expectancy and information quality are positively
related to the intention to use digital library, while service quality is
negatively related to the intention to use digital library. Age and
gender have shown no evidence of any significant interactions, while
experience in using digital library significantly interacts with effort
expectancy and intention to use digital library. This has provided the
evidence of a moderating effect of experience in the intention to use
digital library. It is expected that this research will shed new lights
into research of acceptance and intention to use the library in a digital
environment.
Abstract: Over the past few years, companies in developing
countries have implemented enterprise resource planning (ERP)
systems. Regardless of the various benefits of the ERP system, its
adoption and implementation have not been without problems. Many
companies have assigned considerable organizational resources to
their ERP projects, but have encountered unexpected challenges.
Neglecting a number of important factors in ERP projects might lead
to failure instead of success. User satisfaction is among those factors
that has a major influence on ERP implementation success. So, this
paper intends to investigate the key factors that create ERP users-
satisfaction and to discover whether ERP users- satisfaction varies
among different users- profiles. The study was conducted using a
survey questionnaire which was distributed to ERP users in Iranian
organizations. A total of 384 responses were collected and analyzed.
The findings indicated that younger ERP users tend to be more
satisfied with ERP systems. Furthermore, ERP users with more
experiences in IT and also more educated users have more
satisfaction with ERP softwares. However, the study found no
satisfaction differences between men and women users.
Abstract: This paper deals with a novel technique for the
fabrication of Spiral grooves in a dynamic thrust bearing. The main
scheme proposed in this paper is to fabricate the microgrooves using
desktop forming system. This process has advantages compared to the
conventional electro-chemical machining in the viewpoint of a higher
productivity. For this reason, a new testing apparatus is designed and
built for press forming microgrooves on a surface of the thrust bearing.
The material used in this study is sintered Cu-Fe alloy. The effects of
the forming load on the performance of micro press forming are
experimentally investigated. From the experimental results, formed
depths are closed to the target ones with increasing the forming load.
Abstract: Highly ordered TiO2 nanotube (TNT) arrays were
fabricated onto a pre-treated titanium foil by anodic oxidation with a
voltage of 20V in phosphoric acid/sodium fluoride electrolyte. A pretreatment
of titanium foil involved washing with acetone,
isopropanol, ethanol and deionized water. Carbon doped TiO2
nanotubes (C-TNT) was fabricated 'in-situ' with the same method in
the presence of polyvinyl alcohol and urea as carbon sources. The
affects of polyvinyl alcohol concentration and oxidation time on the
composition, morphology and structure of the C-TN were studied by
FE-SEM, EDX and XRD techniques. FESEM images of the
nanotubes showed uniform arrays of C-TNTs. The density and
microstructures of the nanotubes were greatly affected by the content
of PVA. The introduction of the polyvinyl alcohol into the electrolyte
increases the amount of C content inside TiO2 nanotube arrays
uniformly. The influence of carbon content on the photo-current of
C-TNT was investigated and the I-V profiles of the nanotubes were
established. The preliminary results indicated that the 'in-situ'
doping technique produced a superior quality nanotubes compared to
post doping techniques.
Abstract: The affect of the attendance percentage, the overall
GPA and the number of credit hours the student is enrolled in at
specific semester on the grade attained in specific course has been
studied. This study has been performed on three courses offered in
industrial engineering department at the Hashemite University in
Jordan. Study has revealed that the grade attained by a student is
strongly affected by the attendance percentage and his overall GPA
with a value of R2 of 52.5%. Another model that has been
investigated is the relation between the semester GPA and the
attendance percentage, the number of credit hours enrolled in at
specific semester, and the overall GPA. This model gave us a strong
relationship between the semester GPA and attendance percentage
and the overall GPA with a value of R2 of 76.2%.
Abstract: Cement stabilization has been widely used for
improving the strength and stiffness of soft clayey soils. Cement
treated soil specimens used to investigate the stress-strain behaviour in
the laboratory study are usually cured for 7 days. This paper examines
the effects of curing time on the strength and stress strain behaviour of
cement treated marine clay under triaxial loading condition.
Laboratory-prepared cement treated Singapore marine clay with
different mix proportion S-C-W (soil solid-cement solid-water) and
curing time (7 days to 180 days) was investigated through conducting
unconfined compressive strength test and triaxial test. The results
show that the curing time has a significant effect on the unconfined
compressive strength u q , isotropic compression behaviour and stress
strain behaviour. Although the primary yield loci of the cement treated
soil specimens with the same mix proportion expand with curing time,
they are very narrowly banded and have nearly the same shape after
being normalized by isotropic compression primary stress '
py p . The
isotropic compression primary yield stress '
py p was shown to be
linearly related to unconfined compressive strength u q for specimens
with different curing time and mix proportion. The effect of curing
time on the hardening behaviour will diminish with consolidation
stress higher than isotropic compression primary yield stress but its
damping rate is dependent on the cement content.
Abstract: In this paper, Selective Adaptive Parallel Interference Cancellation (SA-PIC) technique is presented for Multicarrier Direct Sequence Code Division Multiple Access (MC DS-CDMA) scheme. The motivation of using SA-PIC is that it gives high performance and at the same time, reduces the computational complexity required to perform interference cancellation. An upper bound expression of the bit error rate (BER) for the SA-PIC under Rayleigh fading channel condition is derived. Moreover, the implementation complexities for SA-PIC and Adaptive Parallel Interference Cancellation (APIC) are discussed and compared. The performance of SA-PIC is investigated analytically and validated via computer simulations.