Abstract: This paper aims to discuss the hydrophilicity about the anodic aluminum oxide (AAO) template with titania nanotubes (NTs). The AAO templates with pore size diameters of 20-250 nm were generated by anodizing 6061 aluminum alloy substrates in acid solution of sulfuric acid (H2SO4), oxalic acid (COOH)2, and phosphoric acid (H3PO4), respectively. TiO2-NTs were grown on AAO templates by the sol-gel deposition process successfully. The water contact angle on AAO/TiO2-NTs surface was lower compared to the water contact angle on AAO surface. So, the characteristic of hydrophilicity was significantly associated with the AAO pore size and what kinds of materials were immersed variables.
Abstract: In this paper, two options of anodic alumina barrier
layer thinning have been demonstrated. The approaches varied with
the duration of the voltage step. It was found that too long step of the
barrier layer thinning process leads to chemical etching of the
nanopores on their top. At the bottoms pores are not fully opened
what is disadvantageous for further applications in nanofabrication.
On the other hand, while the duration of the voltage step is controlled
by the current density (value of the current density cannot exceed
75% of the value recorded during previous voltage step) the pores are
fully opened. However, pores at the bottom obtained with this
procedure have smaller diameter, nevertheless this procedure
provides electric contact between the bare aluminum (substrate) and
electrolyte, what is suitable for template assisted electrodeposition,
one of the most cost-efficient synthesis method in nanotechnology.
Abstract: The porous silicon (PS), formed from the anodization
of a p+ type substrate silicon, consists of a network organized in a
pseudo-column as structure of multiple side ramifications. Structural
micro-topology can be interpreted as the fraction of the interconnected
solid phase contributing to thermal transport. The
reduction of dimensions of silicon of each nanocristallite during the
oxidation induced a reduction in thermal conductivity. Integration of
thermal sensors in the Microsystems silicon requires an effective
insulation of the sensor element. Indeed, the low thermal conductivity
of PS consists in a very promising way in the fabrication of integrated
thermal Microsystems.In this work we are interesting in the
measurements of thermal conductivity (on the surface and in depth)
of PS by the micro-Raman spectroscopy. The thermal conductivity is
studied according to the parameters of anodization (initial doping and
current density. We also, determine porosity of samples by
spectroellipsometry.
Abstract: Anodizing is an electrochemical process that converts the metal surface into a decorative, durable, corrosion-resistant, anodic oxide finish. Aluminum is ideally suited to anodizing, although other nonferrous metals, such as magnesium and titanium, also can be anodized. The anodic oxide structure originates from the aluminum substrate and is composed entirely of aluminum oxide. This aluminum oxide is not applied to the surface like paint or plating, but is fully integrated with the underlying aluminum substrate, so cannot chip or peel. It has a highly ordered, porous structure that allows for secondary processes such as coloring and sealing. In this experimental paper, we focus on a reliable method for fabricating nanoporous alumina with high regularity. Starting from study of nanostructure materials synthesize methods. After that, porous alumina fabricate in the laboratory by anodization of aluminum oxide. Hard anodization processes are employed to fabricate the nanoporous alumina using 0.3M oxalic acid and 90, 120 and 140 anodized voltages. The nanoporous templates were characterized by SEM and FFT. The nanoporous templates using 140 voltages have high ordered. The pore formation, influence of the experimental conditions on the pore formation, the structural characteristics of the pore and the oxide chemical reactions involved in the pore growth are discuss.
Abstract: The electrolyte stirring method of anodization etching
process for manufacturing porous silicon (PS) is reported in this work.
Two experimental setups of nature air stirring (PS-ASM) and
electrolyte stirring (PS-ESM) are employed to clarify the influence of
stirring mechanisms on electrochemical etching process. Compared to
traditional fabrication without any stirring apparatus (PS-TM), a large
plateau region of PS surface structure is obtained from samples with
both stirring methods by the 3D-profiler measurement. Moreover, the
light emission response is also improved by both proposed electrolyte
stirring methods due to the cycling force in electrolyte could
effectively enhance etch-carrier distribution while the electrochemical
etching process is made. According to the analysis of statistical
calculation of photoluminescence (PL) intensity, lower standard
deviations are obtained from PS-samples with studied stirring methods,
i.e. the uniformity of PL-intensity is effectively improved. The
calculated deviations of PL-intensity are 93.2, 74.5 and 64,
respectively, for PS-TM, PS-ASM and PS-ESM.
Abstract: This paper aims to fabricated high quality anodic
aluminum oxide (AAO) film by anodization method. AAO pore size,
pore density, and film thickness can be controlled in 10~500 nm,
108~1011 pore.cm-2, and 1~100 μm. AAO volume and surface area can
be computed based on structural parameters such as thickness, pore
size, pore density, and sample size. Base on the thetorical calculation,
AAO has 100 μm thickness with 15 nm, 60 nm, and 500 nm pore
diameters AAO surface areas are 1225.2 cm2, 3204.4 cm2, and 549.7
cm2, respectively. The large unit surface area which is useful for
adsorption application. When AAO adsorbed pH indictor of
bromphenol blue presented a sensitive pH detection of solution
change. This testing method can further be used for the precise
measurement of biotechnology, convenience measurement of
industrial engineering.
Abstract: Magnesium is used implant material potentially for
non-toxicity to the human body. Due to the excellent
bio-compatibility, Mg alloys is applied to implants avoiding removal
second surgery. However, it is found commercial magnesium alloys
including aluminum has low corrosion resistance, resulting
subcutaneous gas bubbles and consequently the approach as
permanent bio-materials. Generally, Aluminum is known to pollution
substance, and it raises toxicity to nervous system. Therefore
especially Mg-35Zn-3Ca alloy is prepared for new biodegradable
materials in this study. And the pulsed power is used in
constant-current mode of DC power kinds of anodization. Based on
the aforementioned study, it examines corrosion resistance and
biocompatibility by effect of current and frequency variation. The
surface properties and thickness were compared using scanning
electronic microscopy. Corrosion resistance was assessed via
potentiodynamic polarization and the effect of oxide layer on the body
was assessed cell viability. Anodized Mg-35Zn-3Ca alloy has good
biocompatibility in vitro by current and frequency variation.
Abstract: This paper presents the development of low cost Nano membrane fabrication system. The system is specially designed for anodic aluminum oxide membrane. This system is capable to perform the processes such as anodization and electro-polishing. The designed machine was successfully tested for 'mild anodization' (MA) for 48 hours and 'hard anodization' (HA) for 3 hours at constant 0oC. The system is digitally controlled and guided for temperature maintenance during anodization and electro-polishing. The total cost of the developed machine is 20 times less than the multi-cooling systems available in the market which are generally used for this purpose.
Abstract: Highly ordered arrays of TiO2 nanotubes (TiNTs) were grown vertically on Ti foil by electrochemical anodization. We controlled the lengths of these TiNTs from 2.4 to 26.8 ¶üÇóμm while varying the water contents (1, 3, and 6 wt%) of the electrolyte in ethylene glycol in the presence of 0.5 wt% NH4F with anodization for various applied voltages (20–80 V), periods (10–240 min) and temperatures (10–30 oC). For vertically aligned TiNT arrays, not only the increase in their tube lengths, but also their geometric (wall thickness and surface roughness) and crystalline structure lead to a significant influence on photocatalytic activity. The length optimization for methylene blue (MB) photodegradation was 18 μm. Further extending the TiNT length yielded lower photocatalytic activity presumably related to the limited MB diffusion and light-penetration depth into the TiNT arrays. The results indicated that a maximum MB photodegradation rate was obtained for the discrete anatase TiO2 nanotubes with thick and rough walls.
Abstract: Highly ordered TiO2 nanotube (TNT) arrays were
fabricated onto a pre-treated titanium foil by anodic oxidation with a
voltage of 20V in phosphoric acid/sodium fluoride electrolyte. A pretreatment
of titanium foil involved washing with acetone,
isopropanol, ethanol and deionized water. Carbon doped TiO2
nanotubes (C-TNT) was fabricated 'in-situ' with the same method in
the presence of polyvinyl alcohol and urea as carbon sources. The
affects of polyvinyl alcohol concentration and oxidation time on the
composition, morphology and structure of the C-TN were studied by
FE-SEM, EDX and XRD techniques. FESEM images of the
nanotubes showed uniform arrays of C-TNTs. The density and
microstructures of the nanotubes were greatly affected by the content
of PVA. The introduction of the polyvinyl alcohol into the electrolyte
increases the amount of C content inside TiO2 nanotube arrays
uniformly. The influence of carbon content on the photo-current of
C-TNT was investigated and the I-V profiles of the nanotubes were
established. The preliminary results indicated that the 'in-situ'
doping technique produced a superior quality nanotubes compared to
post doping techniques.