Abstract: The major part of light weight timber constructions
consists of insulation. Mineral wool is the most commonly used
insulation due to its cost efficiency and easy handling. The fiber
orientation and porosity of this insulation material enables flowthrough.
The air flow resistance is low. If leakage occurs in the
insulated bay section, the convective flow may cause energy losses
and infiltration of the exterior wall with moisture and particles. In
particular the infiltrated moisture may lead to thermal bridges and
growth of health endangering mould and mildew. In order to prevent
this problem, different numerical calculation models have been
developed. All models developed so far have a potential for
completion. The implementation of the flow-through properties of
mineral wool insulation may help to improve the existing models.
Assuming that the real pressure difference between interior and
exterior surface is larger than the prescribed pressure difference in the
standard test procedure for mineral wool ISO 9053 / EN 29053,
measurements were performed using the measurement setup for
research on convective moisture transfer “MSRCMT".
These measurements show, that structural inhomogeneities of
mineral wool effect the permeability only at higher pressure
differences, as applied in MSRCMT. Additional microscopic
investigations show, that the location of a leak within the
construction has a crucial influence on the air flow-through and the
infiltration rate. The results clearly indicate that the empirical values
for the acoustic resistance of mineral wool should not be used for the
calculation of convective transfer mechanisms.
Abstract: Literature reveals that many investors rely on technical trading rules when making investment decisions. If stock markets are efficient, one cannot achieve superior results by using these trading rules. However, if market inefficiencies are present, profitable opportunities may arise. The aim of this study is to investigate the effectiveness of technical trading rules in 34 emerging stock markets. The performance of the rules is evaluated by utilizing White-s Reality Check and the Superior Predictive Ability test of Hansen, along with an adjustment for transaction costs. These tests are able to evaluate whether the best model performs better than a buy-and-hold benchmark. Further, they provide an answer to data snooping problems, which is essential to obtain unbiased outcomes. Based on our results we conclude that technical trading rules are not able to outperform a naïve buy-and-hold benchmark on a consistent basis. However, we do find significant trading rule profits in 4 of the 34 investigated markets. We also present evidence that technical analysis is more profitable in crisis situations. Nevertheless, this result is relatively weak.
Abstract: Controlled release urea has become popular in agricultural industry as it helps to solve environmental issues and increase crop yield. Recently biomass was identified to replace the polymer used as a coating material in the conventional coated urea. In this paper spreading and contact angle of biomass droplet (lignin, cellulose and clay) on urea surface are investigated experimentally. There were two tests were conducted, sessile drop for contact angle measurement and pendant drop for contact angle measurement. A different concentration of biomass droplet was released from 30 mm above a substrate. Glass was used as a controlled substrate. Images were recorded as soon as the droplet impacted onto the urea before completely adsorb into the urea. Digitized droplets were then used to identify the droplet-s surface tension and contact angle. There is large difference observed between the low surface tension and high surface tension liquids, where the wetting and spreading diameter is higher for lower surface tension. From the contact angle results, the data showed that the biomass coating films were possible as wetting liquid (θ < 90º). Contact angle of biomass coating material gives good indication for the wettablity of a liquid on urea surface.
Abstract: None of the processing models in the software
development has explained the software systems performance
evaluation and modeling; likewise, there exist uncertainty in the
information systems because of the natural essence of requirements,
and this may cause other challenges in the processing of software
development. By definition an extended version of UML (Fuzzy-
UML), the functional requirements of the software defined
uncertainly would be supported. In this study, the behavioral
description of uncertain information systems by the aid of fuzzy-state
diagram is crucial; moreover, the introduction of behavioral diagrams
role in F-UML is investigated in software performance modeling
process. To get the aim, a fuzzy sub-profile is used.
Abstract: In this work, the physical based device model of
AlGaN/GaN high electron mobility transistors (HEMTs) has been
established and the corresponding device operation behavior has
been investigated also by using Sentaurus TCAD from Synopsys.
Advanced AlGaN/GaN hetero-structures with GaN cap layer and AlN
spacer have been considered and the GaN cap layer and AlN spacer
are found taking important roles on the gate leakage blocking and
off-state breakdown voltage enhancement.
Abstract: Bonding has become a routine procedure in several
dental specialties – from prosthodontics to conservative dentistry and
even orthodontics. In many of these fields it is important to be able to
investigate the bonded interfaces to assess their quality. All currently
employed investigative methods are invasive, meaning that samples
are destroyed in the testing procedure and cannot be used again. We
have investigated the interface between human enamel and bonded
ceramic brackets non-invasively, introducing a combination of new
investigative methods – optical coherence tomography (OCT),
fluorescence OCT and confocal microscopy (CM). Brackets were
conventionally bonded on conditioned buccal surfaces of teeth. The
bonding was assessed using these methods. Three dimensional
reconstructions of the detected material defects were developed using
manual and semi-automatic segmentation. The results clearly prove
that OCT, fluorescence OCT and CM are useful in orthodontic
bonding investigations.
Abstract: This study is designed to investigate errors emerged in written texts produced by 30 Turkish EFL learners with an explanatory, and thus, qualitative perspective. Erroneous language elements were identified by the researcher first and then their grammaticality and intelligibility were checked by five native speakers of English. The analysis of the data showed that it is difficult to claim that an error stems from only one single factor since different features of an error are triggered by different factors. Our findings revealed two different types of errors: those which stem from the interference of L1 with L2 and those which are developmental ones. The former type contains more global errors whereas the errors in latter type are more intelligible.
Abstract: The ITE Project is a project that has 1800 km length
and across the Turkey's land through east to west. The project of
pipeline enters geographically from Iran to Doğubayazit (Turkey) in
the east, exits to Greece from Ipsala province of Turkey in the west.
This project is the one of the international projects in such scale that
provides the natural gas of Iran and Caspian Sea through the
European continent. In this investigation, some information will be
given about the methods used to verify the direction of the pipeline
and the technical properties of the results obtained. The cost of
project itself entirely depends on the direction of the pipeline which
would be as short as possible and the specifications of the land cover.
Production standards of 1/2000 scaled digital orthophoto and vectoral
maps as a results of the use of map production materials and methods
(such as high resolution satellite images, and digital aerial images
captured from digital aerial cameras), will also be given in this report.
According to Turkish national map production standards, TM
((Transversal Mercator, 3 degree) projection is used for large scale
map and UTM (Universal Transversal Mercator, 6 degree) is used for
small scale map production standards. Some information is also given
about the projection used in the ITE natural gas pipeline project.
Abstract: The p53 tumor suppressor gene plays two important
roles in genomic stability: blocking cell proliferation after DNA
damage until it has been repaired, and starting apoptosis if the
damage is too critical. Codon 72 exon4 polymorphism (Arg72Pro) of
the P53 gene has been implicated in cancer risk. Various studies have
been done to investigate the status of p53 at codon 72 for arginine
(Arg) and proline (Pro) alleles in different populations and also the
association of this codon 72 polymorphism with various tumors. Our
objective was to investigate the possible association between P53
Arg72Pro polymorphism and susceptibility to colorectal cancer
among Isfahan and Chaharmahal Va Bakhtiari (a part of south west
of Iran) population. We investigated the status of p53 at codon 72 for
Arg/Arg, Arg/Pro and Pro/Pro allele polymorphisms in blood
samples from 145 colorectal cancer patients and 140 controls by
Nested-PCR of p53 exon 4 and digestion with BstUI restriction
enzyme and the DNA fragments were then resolved by
electrophoresis in 2% agarose gel. The Pro allele was 279 bp, while
the Arg allele was restricted into two fragments of 160 and 119 bp.
Among the 145 colorectal cancer cases 49 cases (33.79%) were
homozygous for the Arg72 allele (Arg/Arg), 18 cases (12.41%) were
homozygous for the Pro72 allele (Pro/Pro) and 78 cases (53.8%)
found in heterozygous (Arg/Pro).
In conclusion, it can be said that p53Arg/Arg genotype may be
correlated with possible increased risk of this kind of cancers in south
west of Iran.
Abstract: Levan, an exopolysaccharide, was produced by
Microbacterium laevaniformans and its yield was characterized as a
function of concentrations of date syrup, sucrose and the fermentation
time. The optimum condition for levan production from sucrose was
at concentration of 20% sucrose for 48 h and for date syrup was 25%
for 48 h. The results show that an increase in fermentation time
caused a decrease in the levan production at all concentrations of date
syrup tested. Under these conditions after 48 h in sucrose medium,
levan production reached 48.9 g/L and for date syrup reached 10.48
g/L . The effect of pH on the yield of the purified levan was examined
and the optimum pH for levan production was determined to be 6.0.
Levan was composed mainly of fructose residues when analyzed by
TLC and FT-IR spectroscopy. Date syrup is a cheap substrate widely
available in Iran and has potential for levan production. The thermal
stability of levan was assessed by Thermo Gravimetric Analysis
(TGA) that revealed the onset of decomposition near to 49°C for the
levan produced from sucrose and 51°C for the levan from date syrup.
DSC results showed a single Tg at 98°C for levan produced from
sucrose and 206 °C for levan from date syrup.
Abstract: This paper presents the results of the experimental
tests of the cooling performance of a 12,000-Btu/h modified air
conditioner (referred to as M-AC) that use the ground as a heat sink
of a condenser. In the tests, cooling capacity of M-AC with an
optimal length of a condensing coil as well as life expectancy of
copper coil buried underground were investigated. The lengths of
copper coil fabricated and used as condenser coil of M-AC were set
at 67, 50, 40 and 30 m whereas that of a 12,000-Btu/h conventional
split-type air conditioner (referred to as C-AC) was about 22 m. The
results showed that the ground can absorb heat rejected from a
condenser of M-AC. The coefficient of performance (COP) of C-AC
was about 2.5 whereas those of M-AC were found to be higher. It
was found that the values of COP of M-AC with condensing coils of
67, 50 and 40 m long were about 6.9, 5.5 and 3.3, respectively, while
that of 30-m-long one was found to be about 2.1. The electrical
consumptions of M-AC were found lower than that of C-AC in the
range of 11.5 – 15.5%. Additionally, life expectancy of underground
condensing coil of M-AC was found to be over 7 years.
Abstract: 17α-ethynylestradiol (EE2) is a synthetic estrogen
used as a key ingredient in an oral contraceptives pill. EE2 is an
endocrine disrupting compound, high in estrogenic potency.
Although EE2 exhibits low degree of biodegradability with common
microorganisms in wastewater treatment plants (WWTPs), this
compound can be biotransformed by ammonia-oxidizing bacteria
(AOB) via a co-metabolism mechanism in WWTPs. This study
aimed to investigate the effect of real wastewater on
biotransformation of EE2 by AOB. A preliminary experiment on the
effect of nitrite and pH levels on abiotic transformation of EE2
suggested that the abiotic transformation occurred at only pH
Abstract: We aimed to investigate how can target and optimize
pulmonary delivery distribution by changing physicochemical
characteristics of instilled liquid.Therefore, we created a new liquids
group:
a. eligible for desired distribution within lung because of
assorted physicochemical characteristics
b. capable of being augmented with a broad range of
chemicals inertly
c. no interference on respiratory function
d. compatible with airway surface liquid
We developed forty types of new liquid,were composed of
Carboxymethylcellulose sodium,Glycerin and different types of
Polysorbates.Viscosity was measured using a Programmable
Rheometer and surface tension by KRUSS Tensiometer.We
subsequently examined the liquids and delivery protocols by simple
and branched glass capillary tube models of airways.Eventually,we
explored pulmonary distribution of liquids being augmented with
technetium-99m in mechanically ventilated rabbits.We used a single
head large field of view gamma camera.Kinematic viscosity between
0.265Stokes and 0.289Stokes,density between 1g/cm3 and 1.5g/cm3
and surface tension between 25dyn/cm and 35dyn/cm were the most
acceptable.
Abstract: The paper deals with the estimation of amplitude and phase of an analogue multi-harmonic band-limited signal from irregularly spaced sampling values. To this end, assuming the signal fundamental frequency is known in advance (i.e., estimated at an independent stage), a complexity-reduced algorithm for signal reconstruction in time domain is proposed. The reduction in complexity is achieved owing to completely new analytical and summarized expressions that enable a quick estimation at a low numerical error. The proposed algorithm for the calculation of the unknown parameters requires O((2M+1)2) flops, while the straightforward solution of the obtained equations takes O((2M+1)3) flops (M is the number of the harmonic components). It is applied in signal reconstruction, spectral estimation, system identification, as well as in other important signal processing problems. The proposed method of processing can be used for precise RMS measurements (for power and energy) of a periodic signal based on the presented signal reconstruction. The paper investigates the errors related to the signal parameter estimation, and there is a computer simulation that demonstrates the accuracy of these algorithms.
Abstract: Let R be a ring and n a fixed positive integer, we
investigate the properties of n-strongly Gorenstein projective, injective
and flat modules. Using the homological theory , we prove that
the tensor product of an n-strongly Gorenstein projective (flat) right
R -module and projective (flat) left R-module is also n-strongly
Gorenstein projective (flat). Let R be a coherent ring ,we prove that
the character module of an n -strongly Gorenstein flat left R -module
is an n-strongly Gorenstein injective right R -module . At last, let
R be a commutative ring and S a multiplicatively closed set of R ,
we establish the relation between n -strongly Gorenstein projective
(injective , flat ) R -modules and n-strongly Gorenstein projective
(injective , flat ) S−1R-modules. All conclusions in this paper is
helpful for the research of Gorenstein dimensions in future.
Abstract: Three alumina-supported Pt-Sn catalysts have been
prepared by means of co-impregnation and characterized by XRD and
N2 adsorption. The influence of catalyst composition and reaction
conditions on the conversion and selectivity were investigated in the
hydrogenation of acetic acid in an isothermal integral fixed bed
reactor. The experiments were performed on the temperature interval
468-548 K, liquid hourly space velocity (LHSV) of 0.3-0.7h-1,
pressures between 1.0 and 5.0Mpa. A good compromise of
0.75%Pt-1.5%Sn can act as an optimized acetic acid hydrogenation
catalyst, and the conversion and selectivity can be tuned through the
variation of reaction conditions.
Abstract: Experimental investigations were carried out in the
Manchester Tidal flow Facility (MTF) to study the flow patterns in
the region around and adjacent to a hypothetical headland in tidal
(oscillatory) ambient flow. The Planar laser-induced fluorescence
(PLIF) technique was used for visualization, with fluorescent dye
released at specific points around the headland perimeter and in its
adjacent recirculation zone. The flow patterns can be generalized into
the acceleration, stable flow and deceleration stages for each halfcycle,
with small variations according to location, which are more
distinct for low Keulegan-Carpenter number (KC) cases. Flow
patterns in the mixing region are unstable and complex, especially in
the recirculation zone. The flow patterns are in agreement with
previous visualizations, and support previous results in steady
ambient flow. It is suggested that the headland lee could be a viable
location for siting of pollutant outfalls.
Abstract: The purpose of this paper is to solve the problem of protecting aerial lines from high impedance faults (HIFs) in distribution systems. This investigation successfully applies 3I0 zero sequence current to solve HIF problems. The feature extraction system based on discrete wavelet transform (DWT) and the feature identification technique found on statistical confidence are then applied to discriminate effectively between the HIFs and the switch operations. Based on continuous wavelet transform (CWT) pattern recognition of HIFs is proposed, also. Staged fault testing results demonstrate that the proposed wavelet based algorithm is feasible performance well.
Abstract: Information sharing and exchange, rather than
information processing, is what characterizes information
technology in the 21st century. Ontologies, as shared common
understanding, gain increasing attention, as they appear as the
most promising solution to enable information sharing both at
a semantic level and in a machine-processable way. Domain
Ontology-based modeling has been exploited to provide
shareability and information exchange among diversified,
heterogeneous applications of enterprises.
Contextual ontologies are “an explicit specification of
contextual conceptualization". That is: ontology is
characterized by concepts that have multiple representations
and they may exist in several contexts. Hence, contextual
ontologies are a set of concepts and relationships, which are
seen from different perspectives. Contextualization is to allow
for ontologies to be partitioned according to their contexts.
The need for contextual ontologies in enterprise modeling
has become crucial due to the nature of today's competitive
market. Information resources in enterprise is distributed and
diversified and is in need to be shared and communicated
locally through the intranet and globally though the internet.
This paper discusses the roles that ontologies play in an
enterprise modeling, and how ontologies assist in building a
conceptual model in order to provide communicative and
interoperable information systems. The issue of enterprise
modeling based on contextual domain ontology is also
investigated, and a framework is proposed for an enterprise
model that consists of various applications.
Abstract: Recent theorizations on the cognitive process of moral
judgment have focused on the role of intuitions and emotions, marking
a departure from previous emphasis on conscious, step-by-step
reasoning. My study investigated how being in a disgusted mood state
affects moral judgment.
Participants were induced to enter a disgusted mood state through
listening to disgusting sounds and reading disgusting descriptions.
Results shows that they, when compared to control who have not been
induced to feel disgust, are more likely to endorse actions that are
emotionally aversive but maximizes utilitarian return
The result is analyzed using the 'emotion-as-information' approach
to decision making. The result is consistent with the view that
emotions play an important role in determining moral judgment.