Abstract: In this study, the designed dual stage membrane
bioreactor (MBR) system was conceptualized for the treatment of
cyanide and heavy metals in electroplating wastewater. The design
consisted of a primary treatment stage to reduce the impact of
fluctuations and the secondary treatment stage to remove the residual
cyanide and heavy metal contaminants in the wastewater under
alkaline pH conditions. The primary treatment stage contained
hydrolyzed Citrus sinensis (C. sinensis) pomace and the secondary
treatment stage contained active Aspergillus awamori (A. awamori)
biomass, supplemented solely with C. sinensis pomace extract from
the hydrolysis process. An average of 76.37%, 95.37%, 93.26 and
94.76% and 99.55%, 99.91%, 99.92% and 99.92% degradation
efficiency for total cyanide (T-CN), including the sorption of nickel
(Ni), zinc (Zn) and copper (Cu) were observed after the first and
second treatment stages, respectively. Furthermore, cyanide
conversion by-products degradation was 99.81% and 99.75 for both
formate (CHOO-) and ammonium (NH4
+) after the second treatment
stage. After the first, second and third regeneration cycles of the C.
sinensis pomace in the first treatment stage, Ni, Zn and Cu removal
achieved was 99.13%, 99.12% and 99.04% (first regeneration cycle),
98.94%, 98.92% and 98.41% (second regeneration cycle) and 98.46
%, 98.44% and 97.91% (third regeneration cycle), respectively.
There was relatively insignificant standard deviation detected in all
the measured parameters in the system which indicated
reproducibility of the remediation efficiency in this continuous
system.
Abstract: Orthogonal Frequency Division Multiplexing
(OFDM) is an efficient method of data transmission for high speed
communication systems. However, the main drawback of OFDM
systems is that, it suffers from the problem of high Peak-to-Average
Power Ratio (PAPR) which causes inefficient use of the High Power
Amplifier and could limit transmission efficiency. OFDM consist of
large number of independent subcarriers, as a result of which the
amplitude of such a signal can have high peak values. In this paper,
we propose an effective reduction scheme that combines DCT and
SLM techniques. The scheme is composed of the DCT followed by
the SLM using the Riemann matrix to obtain phase sequences for the
SLM technique. The simulation results show PAPR can be greatly
reduced by applying the proposed scheme. In comparison with
OFDM, while OFDM had high values of PAPR –about 10.4dB our
proposed method achieved about 4.7dB reduction of the PAPR with
low complexities computation. This approach also avoids
randomness in phase sequence selection, which makes it simpler to
decode at the receiver. As an added benefit, the matrices can be
generated at the receiver end to obtain the data signal and hence it is
not required to transmit side information (SI).
Abstract: In this paper, we consider the problem for identifying the unknown source in the Poisson equation. A modified Tikhonov regularization method is presented to deal with illposedness of the problem and error estimates are obtained with an a priori strategy and an a posteriori choice rule to find the regularization parameter. Numerical examples show that the proposed method is effective and stable.
Abstract: Determination of nano particle size is substantial since
the nano particle size exerts a significant effect on various properties
of nano materials. Accordingly, proposing non-destructive, accurate
and rapid techniques for this aim is of high interest. There are some
conventional techniques to investigate the morphology and grain size
of nano particles such as scanning electron microscopy (SEM),
atomic force microscopy (AFM) and X-ray diffractometry (XRD).
Vibrational spectroscopy is utilized to characterize different
compounds and applied for evaluation of the average particle size
based on relationship between particle size and near infrared spectra
[1,4] , but it has never been applied in quantitative morphological
analysis of nano materials. So far, the potential application of nearinfrared
(NIR) spectroscopy with its ability in rapid analysis of
powdered materials with minimal sample preparation, has been
suggested for particle size determination of powdered
pharmaceuticals. The relationship between particle size and diffuse
reflectance (DR) spectra in near infrared region has been applied to
introduce a method for estimation of particle size. Back propagation
artificial neural network (BP-ANN) as a nonlinear model was applied
to estimate average particle size based on near infrared diffuse
reflectance spectra. Thirty five different nano TiO2 samples with
different particle size were analyzed by DR-FTNIR spectrometry and
the obtained data were processed by BP- ANN.
Abstract: A DEA model can generally evaluate the performance
using multiple inputs and outputs for the same period. However, it is
hard to avoid the production lead time phenomenon some times, such
as long-term project or marketing activity. A couple of models have
been suggested to capture this time lag issue in the context of DEA.
This paper develops a dual-MPO model to deal with time lag effect in
evaluating efficiency. A numerical example is also given to show that
the proposed model can be used to get efficiency and reference set of
inefficient DMUs and to obtain projected target value of input
attributes for inefficient DMUs to be efficient.
Abstract: This study adopted previous fault patterns, results of
detection analysis, historical records and data, and experts-
experiences to establish fuzzy principles and estimate the failure
probability index of components of a power transformer. Considering
that actual parameters and limiting conditions of parameters may
differ, this study used the standard data of IEC, IEEE, and CIGRE as
condition parameters. According to the characteristics of each
condition parameter, relative degradation was introduced to reflect the
degree of influence of the factors on the transformer condition. The
method of fuzzy mathematics was adopted to determine the
subordinate function of the transformer condition. The calculation
used the Matlab Fuzzy Tool Box to select the condition parameters of
coil winding, iron core, bushing, OLTC, insulating oil and other
auxiliary components and factors (e.g., load records, performance
history, and maintenance records) of the transformer to establish the
fuzzy principles. Examples were presented to support the rationality
and effectiveness of the evaluation method of power transformer
performance conditions, as based on fuzzy comprehensive evaluation.
Abstract: The main aim of this paper is to investigate the exponential stability of the Euler method for a stochastic age-dependent population equations with Poisson random measures. It is proved that the Euler scheme is exponentially stable in mean square sense. An example is given for illustration.
Abstract: The problem of exponential stability and periodicity for a class of cellular neural networks (DCNNs) with time-varying delays is investigated. By dividing the network state variables into subgroups according to the characters of the neural networks, some sufficient conditions for exponential stability and periodicity are derived via the methods of variation parameters and inequality techniques. These conditions are represented by some blocks of the interconnection matrices. Compared with some previous methods, the method used in this paper does not resort to any Lyapunov function, and the results derived in this paper improve and generalize some earlier criteria established in the literature cited therein. Two examples are discussed to illustrate the main results.
Abstract: Irradiation is considered one of the most efficient technological processes for the reduction of microorganisms in food. It can be used to improve the safety of food products, and to extend their shelf lives. The aim of this study was to evaluate the effects of gamma irradiation for improvement of saffron shelf life. Samples were treated with 0 (none irradiated), 1.0, 2.0, 3.0 and 4.0 kGy of gamma irradiation and held for 2 months. The control and irradiated samples were underwent microbial analysis, chemical characteristics and sensory evaluation at 30 days intervals. Microbial analysis indicated that irradiation had a significant effect (P < 0.05) on the reduction of microbial loads. There was no significant difference in sensory quality and chemical characteristics during storage in saffron.
Abstract: Coarse and fine particulate matter were collected at a
residential area at Vashi, Navi Mumbai and the filter samples were
analysed for trace elements using PIXE technique. The trend of
particulate matter showed higher concentrations during winter than
the summer and monsoon concentration levels. High concentrations
of elements related to soil and sea salt were found in PM10 and
PM2.5. Also high levels of zinc and sulphur found in the particulates
of both the size fractions. EF analysis showed enrichment of Cu, Cr
and Mn only in the fine fraction suggesting their origin from
anthropogenic sources. The EF value was observed to be maximum
for As, Pb and Zn in the fine particulates. However, crustal derived
elements showed very low EF values indicating their origin from
soil. The PCA based multivariate studies identified soil, sea salt,
combustion and Se sources as common sources for coarse and
additionally an industrial source has also been identified for fine
particles.
Abstract: Tungsten trioxide has been prepared by using P-PTA
as a precursor on alumina substrates by spin coating method.
Palladium introduced on WO3 film via electrolysis deposition by
using palladium chloride as catalytic precursor. The catalytic
precursor was introduced on the series of films with different
morphologies. X-ray diffractometry (XRD), Scanning electron
microscopy (SEM) and XPS were applied to analyze structure and
morphology of the fabricated thin films. Then we measured variation
of samples- electrical conductivity of pure and Pd added films in air
and diluted hydrogen. Addition of Pd resulted in a remarkable
improvement of the hydrogen sensing properties of WO3 by detection
of Hydrogen below 1% at room temperature. Also variation of the
electrical conductivity in the presence of diluted hydrogen revealed
that response of samples depends rather strongly on the palladium
configuration on the surface.
Abstract: This study aims to clarify constructions which enable to improve socio-cultural values of environments and also to obtain new knowledge on selecting development plans. CVM is adopted as a method of evaluation. As a case of the research, university campus (CP; the following) is selected on account of its various environments, institutions and many users. Investigations were conducted from 4 points of view, total value and utility value of whole CP environments, values of each environment existing in CP or development plan assumed in CP. Furthermore, respondents- attributes were also investigated. In consequence, the following is obtained. 1) Almost all of total value of CP is composed of utility value of direct use. 2) Each of environment and development plans whose value is the highest is clarified. 3) Moreover, development plan to improve environmental value the most is specified.
Abstract: A multivariable discontinuous feedback linearization approach is proposed to position control of an electrically driven fast robot manipulator. A desired performance is achieved by selecting a useful controller and suitable sampling rate and considering saturation for actuators. There is a high flexibility to apply the proposed control approach on different electrically driven manipulators. The control approach can guarantee the stability and satisfactory tracking performance. A PUMA 560 robot driven by geared permanent magnet dc motors is simulated. The simulation results show a desired performance for control system under technical specifications.
Abstract: The increasing competitiveness in manufacturing
industry is forcing manufacturers to seek effective processing
schedules. The paper presents an optimization manufacture
scheduling approach for dependent details processing with given
processing sequences and times on multiple machines. By defining
decision variables as start and end moments of details processing it is
possible to use straightforward variables restrictions to satisfy
different technological requirements and to formulate easy to
understand and solve optimization tasks for multiple numbers of
details and machines. A case study example is solved for seven base
moldings for CNC metalworking machines processed on five
different machines with given processing order among details and
machines and known processing time-s duration. As a result of linear
optimization task solution the optimal manufacturing schedule
minimizing the overall processing time is obtained. The
manufacturing schedule defines the moments of moldings delivery
thus minimizing storage costs and provides mounting due-time
satisfaction. The proposed optimization approach is based on real
manufacturing plant problem. Different processing schedules variants
for different technological restrictions were defined and implemented
in the practice of Bulgarian company RAIS Ltd. The proposed
approach could be generalized for other job shop scheduling
problems for different applications.
Abstract: This work presents a fusion of Log Gabor Wavelet
(LGW) and Maximum a Posteriori (MAP) estimator as a speech
enhancement tool for acoustical background noise reduction. The
probability density function (pdf) of the speech spectral amplitude is
approximated by a Generalized Laplacian Distribution (GLD).
Compared to earlier estimators the proposed method estimates the
underlying statistical model more accurately by appropriately
choosing the model parameters of GLD. Experimental results show
that the proposed estimator yields a higher improvement in
Segmental Signal-to-Noise Ratio (S-SNR) and lower Log-Spectral
Distortion (LSD) in two different noisy environments compared to
other estimators.
Abstract: This present paper proposes the modified Elastic Strip
method for mobile robot to avoid obstacles with a real time system in
an uncertain environment. The method deals with the problem of
robot in driving from an initial position to a target position based on
elastic force and potential field force. To avoid the obstacles, the
robot has to modify the trajectory based on signal received from the
sensor system in the sampling times. It was evident that with the
combination of Modification Elastic strip and Pseudomedian filter to
process the nonlinear data from sensor uncertainties in the data
received from the sensor system can be reduced. The simulations and
experiments of these methods were carried out.
Abstract: Monitoring of ecological systems is one of the major
issues in ecosystem research. The concepts and methodology of
mathematical systems theory provide useful tools to face this
problem. In many cases, state monitoring of a complex ecological
system consists in observation (measurement) of certain state
variables, and the whole state process has to be determined from the
observed data. The solution proposed in the paper is the design of an
observer system, which makes it possible to approximately recover
the state process from its partial observation. The method is
illustrated with a trophic chain of resource – producer – primary
consumer type and a numerical example is also presented.
Abstract: In a wireless communication system, a
predistorter(PD) is often employed to alleviate nonlinear distortions
due to operating a power amplifier near saturation, thereby improving
the system performance and reducing the interference to adjacent
channels. This paper presents a new adaptive polynomial digital
predistorter(DPD). The proposed DPD uses Coordinate Rotation
Digital Computing(CORDIC) processors and PD process by pipelined
architecture. It is simpler and faster than conventional adaptive
polynomial DPD. The performance of the proposed DPD is proved by
MATLAB simulation.
Abstract: Larval survey was carried out in 6 localities in the
urban areas (Putrajaya) and suburban areas (Kuala Selangor) from
January until December 2010. A total of 520 representative
households in 6 localities were selected. Breeding habitats were
sampled outdoors in the surroundings of housing areas. The study
indicated that the most predominant species found in both areas was
Aedes albopictus with the gardening utensil as a preferred breeding
microhabitat for Putrajaya, in contrast to the artificial containers for
Kuala Selangor. From a total of 1083 mosquito larvae species, 984
were Aedes albopictus larvae, 67 positive larvae of Aedes aegypti
and 32 of Culex larvae. Aedes Index and Container Index were
elevated in Putrajaya with 13% and 11% respectively which is higher
than the standard given by the Ministry of Health, Malaysia. This
results implicating dengue-sensitive skewed to the urban areas.
Breteau Index result also above the standard in both study locations.
Abstract: The aim of current study was to investigate the
changes in the quality parameters of Holstein bull semen during the
heat stress and the effect of feeding a source of omega-3 fatty acids
in this period. Samples were obtained from 19 Holstein bulls during
the expected time of heat stress in Iran (June to September 2009).
Control group (n=10) were fed a standard concentrate feed while
treatment group (n=9) had this feed top dressed with 100 g of an
omega-3 enriched nutriceutical. Semen quality was assessed on
ejaculates collected after 1, 5, 9 and 12 weeks of supplementation.
Computer-assisted assessment of sperm motility, viability (eosinnigrosin)
and hypo-osmotic swelling test (HOST) were conducted.
Heat stress affected sperm quality parameters by week 5 and 9
(p