Abstract: In order to better understand the long term
implications of the grout wear failure mode in large-diameter plainsided
grouted connections, a numerical model has been developed
and calibrated that can take advantage of existing operational plant
data to predict the wear accumulation for the actual load conditions
experienced over a given period, thus limiting the requirement for
expensive monitoring systems. This model has been derived and
calibrated based on site structural condition monitoring (SCM) data
and supervisory control and data acquisition systems (SCADA) data
for two operational wind turbine generator substructures afflicted
with this challenge, along with experimentally derived wear rates.
Abstract: A mixed method by combining modified pole
clustering technique and modified cauer continued fraction is
proposed for reducing the order of the large-scale dynamic systems.
The denominator polynomial of the reduced order model is obtained
by using modified pole clustering technique while the coefficients of
the numerator are obtained by modified cauer continued fraction.
This method generated 'k' number of reduced order models for kth
order reduction. The superiority of the proposed method has been
elaborated through numerical example taken from the literature and
compared with few existing order reduction methods.
Abstract: Composite materials, due to their unique properties
such as high strength to weight ratio, corrosion resistance, and impact
resistance have huge potential as structural materials in automotive,
construction and transportation applications. However, these
properties often come at higher cost owing to complex design
methods, difficult manufacturing processes and raw material cost.
Traditionally, tapered laminated composite structures are
manufactured using autoclave manufacturing process by ply drop off
technique. Autoclave manufacturing though very powerful suffers
from high capital investment and higher energy consumption. As per
the current trends in composite manufacturing, Out of Autoclave
(OoA) processes are looked as emerging technologies for
manufacturing the structural composite components for aerospace
and defense applications. However, there is a need for improvement
among these processes to make them reliable and consistent. In this
paper, feasibility of using out of autoclave process to manufacture the
variable thickness cantilever beam is discussed. The minimum weight
design for the composite beam is obtained using constant stress beam
concept by tailoring the thickness of the beam. Ply drop off
techniques was used to fabricate the variable thickness beam from
glass/epoxy prepregs. Experiments were conducted to measure
bending stresses along the span of the cantilever beam at different
intervals by applying the concentrated load at the free end.
Experimental results showed that the stresses in the bean at different
intervals were constant. This proves the ability of OoA process to
manufacture the constant stress beam. Finite element model for the
constant stress beam was developed using commercial finite element
simulation software. It was observed that the simulation results
agreed very well with the experimental results and thus validated
design and manufacturing approach used.
Abstract: For cycling, the analysis of the pedal force is one of the
important factors in the study of exercise ability assessment and
overuse injuries. In past studies, a two-axis measurement sensor was
used at the sagittal plane to measure the force only in the anterior,
posterior, and vertical directions and to analyze the loss of force and
the injury on the frontal plane due to the forces in the right and left
directions. In this study, which is a basic study on diverse analyses of
the pedal force that consider the forces on the sagittal plane and the
frontal plane, a three-axis pedal force measurement sensor was
developed to measure the anterior-posterior (Fx), medio-lateral (Fz),
and vertical (Fy) forces. The sensor was fabricated with a size and
shape similar to those of the general flat pedal, and had a 550g weight
that allowed smooth pedaling. Its measurement range was ±1000 N for
Fx and Fz and ±2000 N for Fy, and its non-linearity, hysteresis, and
repeatability were approximately 0.5%. The data were sampled at
1000 Hz using a signal collector. To use the developed sensor, the
pedaling efficiency (index of efficiency, IE) and the range of left and
right (medio-lateral, ML) forces were measured with two seat heights
(low and high). The results of the measurement showed that the IE was
higher and the force range in the ML direction was lower with the high
position than with the low position. The developed measurement
sensor and its application results will be useful in understanding and
explaining the complicated pedaling technique, and will enable
diverse kinematic analyses of the pedal force on the sagittal plane and
the frontal plane.
Abstract: The effect of the inclusion of thyme and rosemary
essential oils into chitosan films, as well as the microbiological and
physical properties when storing chitosan film with and without the
mentioned inclusion was studied. The film forming solution was
prepared by dissolving chitosan (2%, w/v), polysorbate 80 (4% w/w
CH) and glycerol (16% w/w CH) in aqueous lactic acid solutions
(control). The thyme (TEO) and rosemary (REO) essential oils (EOs)
were included 1:1 w/w (EOs:CH) on their combination 50/50
(TEO:REO). The films were stored at temperatures of 5, 20, 33°C
and a relative humidity of 75% during four weeks. The films with
essential oil inclusion did not show an antimicrobial activity against
strains. This behavior could be explained because the chitosan only
inhibits the growth of microorganisms in direct contact with the
active sites. However, the inhibition capacity of TEO was higher than
the REO and a synergic effect between TEO:REO was found for S.
enteritidis strains in the chitosan solution.
Some physical properties were modified by the inclusion of
essential oils. The addition of essential oils does not affect the
mechanical properties (tensile strength, elongation at break, puncture
deformation), the water solubility, the swelling index nor the DSC
behavior. However, the essential oil inclusion can significantly
decrease the thickness, the moisture content, and the L* value of
films whereas the b* value increased due to molecular interactions
between the polymeric matrix, the loosing of the structure, and the
chemical modifications. On the other hand, the temperature and time
of storage changed some physical properties on the chitosan films.
This could have occurred because of chemical changes, such as
swelling in the presence of high humidity air and the reacetylation of
amino groups. In the majority of cases, properties such as moisture
content, tensile strength, elongation at break, puncture deformation,
a*, b*, chrome, 7E increased whereas water resistance, swelling
index, L*, and hue angle decreased.
Abstract: In the last few decades, many southeast-Asia women
migrate to Taiwan by marriage, and it usually takes several years for
them to acquire Taiwanese citizenship. This study investigates the
relationship between their citizenship acquisition and whether they
develop Taiwanese identities, and how does it affect their ethnical
identity towards their original ethnics. Furthermore, the present study
also explores that whether citizenship acquisition help the immigrant
women to explore the host society further and make commitment to it,
or the identification towards mainstream Taiwanese society is only
symbolic and superficial? One hundred and ninety-two immigrant
women were measured using Multigroup Ethnic Identity
Measure-Revised and a global 10-point ethnic identity question.
Correlation tests, t-test, and hierarchical regression were performed to
answer the above questions. The results revealed that citizenship
acquisition does help immigrant women to identify with Taiwanese
society, but it does not affect how they identify with their own ethnics.
Furthermore, the results also indicated that acquiring citizenship
would not help these immigrant women become involved in deeper
cultural exploration of Taiwan nor would it encourage them to make
commitments to the host society.
Abstract: The design, manufacture, and operation of thin-walled
pressure vessels must be based on maximum safe operating pressure
and an adequate factor of safety (FoS). This research paper first
reports experimental evaluation of longitudinal and hoops stresses
based on working pressure as well as maximum pressure; and then
includes a critical study of factor of safety (FoS) in the design of a
glass fiber pressure vessel. Experimental work involved the use of
measuring instruments and the readings from pressure gauges.
Design calculations involved the computations of design stress and
FoS; the latter was based on breaking strength of 55 MPa for the
glass fiber (pressure-vessel material). The experimentally determined
FoS value has been critically compared with the general FoS allowed
in the design of glass fiber pressure vessels.
Abstract: Chemical Reaction Optimization (CRO) is an
optimization metaheuristic inspired by the nature of chemical
reactions as a natural process of transforming the substances from
unstable to stable states. Starting with some unstable molecules with
excessive energy, a sequence of interactions takes the set to a state of
minimum energy. Researchers reported successful application of the
algorithm in solving some engineering problems, like the quadratic
assignment problem, with superior performance when compared with
other optimization algorithms. We adapted this optimization
algorithm to the Printed Circuit Board Drilling Problem (PCBDP)
towards reducing the drilling time and hence improving the PCB
manufacturing throughput. Although the PCBDP can be viewed as
instance of the popular Traveling Salesman Problem (TSP), it has
some characteristics that would require special attention to the
transactions that explore the solution landscape. Experimental test
results using the standard CROToolBox are not promising for
practically sized problems, while it could find optimal solutions for
artificial problems and small benchmarks as a proof of concept.
Abstract: A Silver (Ag) thin film is introduced as a template and
doping source for vertically aligned p–type ZnO nanorods. ZnO
nanorods were grown using an ammonium hydroxide based
hydrothermal process. During the hydrothermal process, the Ag thin
film was dissolved to generate Ag ions in the solution. The Ag ions can
contribute to doping in the wurzite structure of ZnO and the (111)
grain of Ag thin film can be the epitaxial temporal template for the
(0001) plane of ZnO. Hence, Ag–doped p–type ZnO nanorods were
successfully grown on the substrate, which can be an electrode or
semiconductor for the device application. To demonstrate the
potentials of this idea, p–n diode was fabricated and its electrical
characteristics were demonstrated.
Abstract: Lightweight design represents an important key to
successful implementation of energy-saving, fuel-efficient and
environmentally friendly means of transport in the aerospace and
automotive industry. In this context the use of carbon fibre reinforced
plastics (CFRP) which are distinguished by their outstanding
mechanical properties at relatively low weight, promise significant
improvements. Due to the reduction of the total mass, with the
resulting lowered fuel or energy consumption and CO2 emissions
during the operational phase, commercial aircraft will increasingly be
made of CFRP. An auspicious technology for the efficient and
economic production of high performance thermoset composites and
hybrid structures for future lightweight applications is the
combination of carbon fibre sheet moulding compound, tailored
continuous carbon fibre reinforcements and metallic components in a
one-shot pressing and curing process. This paper deals with a hybrid
composite technology for aerospace industries, which was developed
with the help of a special innovation and development system.
Abstract: This paper investigates the activity of the rectus
femoris (RF) and biceps femoris (BF) in healthy subjects during salat
(prostration) and specific exercise (squat exercise) using
electromyography (EMG). A group of undergraduates aged between
19 to 25 years voluntarily participated in this study. The myoelectric
activity of the muscles were recorded and analyzed. The finding
indicated that there were contractions of the muscles during the salat
and exercise with almost same EMG’s level. From the result,
Wilcoxon’s Rank Sum test showed significant difference between
prostration and squat exercise (p
Abstract: Vertical Handover(VHO) among different
communication technologies ensuring uninterruption and service
continuity is one of the most important performance parameter in
Heterogenous networks environment. In an integrated Universal
Mobile Telecommunicatin System(UMTS) and Wireless Local
Area Network(WLAN), WLAN is given an inherent priority over
UMTS because of its high data rates with low cost. Therefore
mobile users want to be associated with WLAN maximum of the
time while roaming, to enjoy best possible services with low cost.
That encourages reduction of number of VHO. In this work the
reduction of number of VHO with respect to varying number of
WLAN Access Points(APs) in an integrated UMTS and WLAN
network is investigated through simulation to provide best possible
cost effective service to the users. The simulation has been carried
out for an area (7800 × 9006)m2 where COST-231 Hata model
and 3GPP (TR 101 112 V 3.1.0) specified models are used for
WLAN and UMTS path loss models respectively. The handover
decision is triggered based on the received signal level as compared
to the fade margin. Fade margin gives a probabilistic measure of
the reliability of the communication link. A relationship between
number of WLAN APs and the number of VHO is also established
in this work.
Abstract: Fugitive particulate matter (PM) is a major source of
airborne pollution in the Middle East countries. The meteorological
conditions and topography of the area makes it highly susceptible to
wind-blown particles which raise many air quality concerns. Air
quality tools such as field monitoring, emission factors and dispersion
modeling have been used in previous research studies to analyze the
release and impacts of fugitive PM in the region. However, these
tools have been originally developed based on experiments made for
European and North American regions. In this work, an experimental
campaign was conducted on April-May 2014 in a construction site in
Doha city, Qatar. The ultimate goal is to evaluate the applicability of
the existing emission factors for construction sites in dry and arid
areas like the Middle East.
Abstract: This paper focuses on the assessment of the air
pollution and morbidity relationship in Tunisia. Air pollution is
measured by ozone air concentration and the morbidity is measured
by the number of respiratory-related restricted activity days during
the 2-week period prior to the interview. Socioeconomic data are also
collected in order to adjust for any confounding covariates. Our
sample is composed by 407 Tunisian respondents; 44.7% are women,
the average age is 35.2, near 69% are living in a house built after
1980, and 27.8% have reported at least one day of respiratory-related
restricted activity. The model consists on the regression of the
number of respiratory-related restricted activity days on the air
quality measure and the socioeconomic covariates. In order to correct
for zero-inflation and heterogeneity, we estimate several models
(Poisson, negative binomial, zero inflated Poisson, Poisson hurdle,
negative binomial hurdle and finite mixture Poisson models).
Bootstrapping and post-stratification techniques are used in order to
correct for any sample bias. According to the Akaike information
criteria, the hurdle negative binomial model has the greatest goodness
of fit. The main result indicates that, after adjusting for
socioeconomic data, the ozone concentration increases the probability
of positive number of restricted activity days.
Abstract: Given the dynamic nature of the higher education
landscape, induction programmes for new academics has become the
norm nowadays to support academics negotiate these rough terrain.
This study investigates an induction programme for new academics
in a higher education institution to establish what difference it has
made to participants. The findings revealed that the benefits ranged
from creating safe spaces for collaboration and networking to
fostering reflective practice and contributing to the scholarship of
teaching and learning. The study also revealed that some of the
intentions of the programme may not have been achieved, for
example transformative learning. This led to questioning whether this
intention is an appropriate one given the short duration of the
programme and the long, drawn out process of transformation. It may
be concluded that the academic induction programme in this study
serves to sow the seeds for transformative learning through fostering
critically reflective practice. Recommendations for further study
could include long term impact of the programme on student learning
and success, these being the core business of higher education. It is
also recommended that in addition to an induction programme, the
university invests in a mentoring programme for new staff and extend
the support for academics in order to sustain critical reflection and
which may contribute to transformative educational practice.
Abstract: Auckland has a temperate climate with comfortable warm, dry summers and mild, wet winters. An Auckland school normally does not need air conditioning for cooling during the summer and only needs heating during the winter. The Auckland school building thermal design should more focus on winter thermal performance and indoor thermal comfort for energy efficiency. This field study of testing indoor and outdoor air temperatures, relative humidity and indoor surface temperatures of three classrooms with different envelopes were carried out in the Avondale College during the winter months in 2013. According to the field study data, this study is to compare and evaluate winter thermal performance and indoor thermal conditions of school buildings with different envelopes.
Abstract: Karst term is the determiner of a variety of areas or
landforms and unique perspectives that have been formed in result of
the of the ingredients dissolution of rocks constituter by natural
waters. Shiraz area with an area of 5322km2 is located in the simple
folded belt in the southern part of Zagros Mountain of Fars, and is
surrounded with Limestone Mountains (Asmari formation). Shiraz
area is located in Calcareous areas. The infrastructure of this city is
lime and absorbing wells that the city can influence the Limestone
dissolution and those accelerate its rate and increase the cavitation
below the surface. Dasht-e Arjan is a graben, which has been created
as the result of activity of two normal faults in its east and west sides.
It is a complete sample of Karst plains (Polje) which has been created
with the help of tectonic forces (fault) and dissolution process of
water in Asmari limestone formation. It is located 60km. off south
west of Shiraz (on Kazeroon-Shiraz road). In 1971, UNESCO has
recognized this plain as a reserve of biosphere. It is considered as one
of the world’s most beautiful geological phenomena, so that most of
the world’s geologists are interested in visiting this place. The
purpose of this paper is to identify and introduce landscapes of Karst
features shiraz city and Dasht-e Arjan including Karst dissolution
features (Lapiez, Karst springs, dolines, caves, underground caves,
ponors, and Karst valleys), anticlines and synclines, and Arjan Lake.
Abstract: Given a graph G. A cycle of G is a sequence of
vertices of G such that the first and the last vertices are the same.
A hamiltonian cycle of G is a cycle containing all vertices of G.
The graph G is k-ordered (resp. k-ordered hamiltonian) if for any
sequence of k distinct vertices of G, there exists a cycle (resp.
hamiltonian cycle) in G containing these k vertices in the specified
order. Obviously, any cycle in a graph is 1-ordered, 2-ordered and 3-
ordered. Thus the study of any graph being k-ordered (resp. k-ordered
hamiltonian) always starts with k = 4. Most studies about this topic
work on graphs with no real applications. To our knowledge, the
chordal ring families were the first one utilized as the underlying
topology in interconnection networks and shown to be 4-ordered.
Furthermore, based on our computer experimental results, it was
conjectured that some of them are 4-ordered hamiltonian. In this
paper, we intend to give some possible directions in proving the
conjecture.
Abstract: Future flood can be predicted using the probable
maximum flood (PMF). PMF is calculated using the historical
discharge or rainfall data considering the other climatic parameters
remaining stationary. However climate is changing globally and the
key climatic variables are temperature, evaporation, rainfall and sea
level rise are likely to change. To develop scenarios to a basin or
catchment scale these important climatic variables should be
considered. Nowadays scenario based on climatic variables is more
suitable than PMF. Six scenarios were developed for a large Fitzroy
basin and presented in this paper.
Abstract: Locating Radio Controlled (RC) devices using their
unintended emissions has a great interest considering security
concerns. Weak nature of these emissions requires near field
localization approach since it is hard to detect these signals in far
field region of array. Instead of only angle estimation, near field
localization also requires range estimation of the source which makes
this method more complicated than far field models. Challenges of
locating such devices in a near field region and real time environment
are analyzed in this paper. An ESPRIT like near field localization
scheme is utilized for both angle and range estimation. 1-D search
with symmetric subarrays is provided. Two 7 element uniform linear
antenna arrays (ULA) are employed for locating RC source.
Experiment results of location estimation for one unintended emitting
walkie-talkie for different positions are given.