Abstract: This paper presents a hand vein authentication system
using fast spatial correlation of hand vein patterns. In order to
evaluate the system performance, a prototype was designed and a
dataset of 50 persons of different ages above 16 and of different
gender, each has 10 images per person was acquired at different
intervals, 5 images for left hand and 5 images for right hand. In
verification testing analysis, we used 3 images to represent the
templates and 2 images for testing. Each of the 2 images is matched
with the existing 3 templates. FAR of 0.02% and FRR of 3.00 %
were reported at threshold 80. The system efficiency at this threshold
was found to be 99.95%. The system can operate at a 97% genuine
acceptance rate and 99.98 % genuine reject rate, at corresponding
threshold of 80. The EER was reported as 0.25 % at threshold 77. We
verified that no similarity exists between right and left hand vein
patterns for the same person over the acquired dataset sample.
Finally, this distinct 100 hand vein patterns dataset sample can be
accessed by researchers and students upon request for testing other
methods of hand veins matching.
Abstract: The object of this paper is to design and analyze a
proportional – integral (PI) control for positive output elementary
super lift Luo converter (POESLLC), which is the start-of-the-art
DC-DC converter. The positive output elementary super lift Luo
converter performs the voltage conversion from positive source
voltage to positive load voltage. This paper proposes a
development of PI control capable of providing the good static and
dynamic performance compared to proportional – integralderivative
(PID) controller. Using state space average method
derives the dynamic equations describing the positive output
elementary super lift luo converter and PI control is designed. The
simulation model of the positive output elementary super lift Luo
converter with its control circuit is implemented in
Matlab/Simulink. The PI control for positive output elementary
super lift Luo converter is tested for transient region, line changes,
load changes, steady state region and also for components
variations.
Abstract: In this paper, we present an experimental testing for
a new algorithm that determines an optimal controller-s coefficients
for output variance reduction related to Linear Time Invariant (LTI)
Systems. The algorithm features simplicity in calculation, generalization
to minimal and non-minimal phase systems, and could be
configured to achieve reference tracking as well as variance reduction
after compromising with the output variance. An experiment of DCmotor
velocity control demonstrates the application of this new
algorithm in designing the controller. The results show that the
controller achieves minimum variance and reference tracking for a
preset velocity reference relying on an identified model of the motor.
Abstract: The broadcast problem including the plan design is
considered. The data are inserted and numbered at predefined order
into customized size relations. The server ability to create a full,
regular Broadcast Plan (RBP) with single and multiple channels after
some data transformations is examined. The Regular Geometric
Algorithm (RGA) prepares a RBP and enables the users to catch their
items avoiding energy waste of their devices. Moreover, the
Grouping Dimensioning Algorithm (GDA) based on integrated
relations can guarantee the discrimination of services with a
minimum number of channels. This last property among the selfmonitoring,
self-organizing, can be offered by servers today
providing also channel availability and less energy consumption by
using smaller number of channels. Simulation results are provided.
Abstract: The vast rural landscape in the southern United States
is conspicuously characterized by the hedgerow trees or groves. The
patchwork landscape of fields surrounded by high hedgerows is a
traditional and familiar feature of the American countryside.
Hedgerows are in effect linear strips of trees, groves, or woodlands,
which are often critical habitats for wildlife and important for the
visual quality of the landscape. As landscape interfaces, hedgerows
define the spaces in the landscape, give the landscape life and
meaning, and enrich ecologies and cultural heritages of the American
countryside. Although hedgerows were originally intended as fences
and to mark property and townland boundaries, they are not merely
the natural or man-made additions to the landscape--they have
gradually become “naturalized" into the landscape, deeply rooted in
the rural culture, and now formed an important component of the
southern American rural environment. However, due to the ever
expanding real estate industry and high demand for new residential
development, substantial areas of authentic hedgerow landscape in
the southern United States are being urbanized. Using Hudson Farm
as an example, this study illustrated guidelines of how hedgerows can
be integrated into town planning as green infrastructure and
landscape interface to innovate and direct sustainable land use, and
suggest ways in which such vernacular landscapes can be preserved
and integrated into new development without losing their contextual
inspiration.
Abstract: Fractional delay FIR filters design method based on
the differential evolution algorithm is presented. Differential evolution
is an evolutionary algorithm for solving a global optimization problems in the continuous search space. In the proposed approach,
an evolutionary algorithm is used to determine the coefficients of
a fractional delay FIR filter based on the Farrow structure. Basic
differential evolution is enhanced with a restricted mating technique,
which improves the algorithm performance in terms of convergence
speed and obtained solution. Evolutionary optimization is carried out by minimizing an objective function which is based on the amplitude
response and phase delay errors. Experimental results show that the proposed algorithm leads to a reduction in the amplitude response and phase delay errors relative to those achieved with the Least-Squares
method.
Abstract: Truss optimization problem has been vastly studied
during the past 30 years and many different methods have been
proposed for this problem. Even though most of these methods
assume that the design variables are continuously valued, in reality,
the design variables of optimization problems such as cross-sectional
areas are discretely valued. In this paper, an improved hill climbing
and an improved simulated annealing algorithm have been proposed
to solve the truss optimization problem with discrete values for crosssectional
areas. Obtained results have been compared to other
methods in the literature and the comparison represents that the
proposed methods can be used more efficiently than other proposed
methods
Abstract: The sustainability of a place depends on a series of factors which contribute to the quality of life, sense of place and recognition of identity. An activity like walking, which in itself is obviously ''sustainable'', can become non sustainable if the context in which it is carried out does not meet the conditions for an adequate quality of life. This work is aimed at proposing the analytical method of Place Maker to identify the elements that do not feature in traditional mapping and which constitute the contemporary identity of the places, and the relative complex map to represent those elements and support sustainable urban identity design. The method's potential for areas with a predominantly pedestrian vocation is illustrated by means of the case study of the Ramblas in Barcelona.
Abstract: This paper aims to explain the project carried out at
the University of Cordoba, specifically at the High Polytechnic
School in collaboration with two other organizations belonging to the
Andalusian Ministry of Innovation, Science and Business:
Andalusian Innovation and Development Agency (IDEA agency) [1]
and the Territorial Net of Entrepreneurship Support (in Spanish Red
Territorial de Apoyo al Emprendedor) [11].
The project is being developed in several stages of which only the
first one has already been completed. However, several important
preliminary results derive from it, based mainly in the description of
the nature of entrepreneurship in the field of university education and
its impact on student-s competency as recommended by the European
Higher Education Area. Some problems holding back the correct
future development will also be shown as derived from the specific
context of application of the project.
Abstract: The main focus of the work was concerned with hydrodynamic and thermal analysis of the plate heat exchanger channel with corrugation patterns suggested to be triangular, sinusoidal, and square corrugation. This study was to numerically model and validate the triangular corrugated channel with dimensions/parameters taken from open literature, and then model/analyze both sinusoidal, and square corrugated channel referred to the triangular model. Initially, 2D modeling with local extensive analysis for triangular corrugated channel was carried out. By that, all local pressure drop, wall shear stress, friction factor, static temperature, heat flux, Nusselt number, and surface heat coefficient, were analyzed to interpret the hydrodynamic and thermal phenomena occurred in the flow. Furthermore, in order to facilitate confidence in this model, a comparison between the values predicted, and experimental results taken from literature for almost the same case, was done. Moreover, a holistic numerical study for sinusoidal and square channels together with global comparisons with triangular corrugation under the same condition, were handled. Later, a comparison between electric, and fluid cooling through varying the boundary condition was achieved. The constant wall temperature and constant wall heat flux boundary conditions were employed, and the different resulted Nusselt numbers as a consequence were justified. The results obtained can be used to come up with an optimal design, a 'compromise' between heat transfer and pressure drop.
Abstract: One important problem in today organizations is the
existence of non-integrated information systems, inconsistency and
lack of suitable correlations between legacy and modern systems.
One main solution is to transfer the local databases into a global one.
In this regards we need to extract the data structures from the legacy
systems and integrate them with the new technology systems. In
legacy systems, huge amounts of a data are stored in legacy
databases. They require particular attention since they need more
efforts to be normalized, reformatted and moved to the modern
database environments. Designing the new integrated (global)
database architecture and applying the reverse engineering requires
data normalization. This paper proposes the use of database reverse
engineering in order to integrate legacy and modern databases in
organizations. The suggested approach consists of methods and
techniques for generating data transformation rules needed for the
data structure normalization.
Abstract: The study of the transport coefficients in electronic
devices is currently carried out by analytical and empirical models.
This study requires several simplifying assumptions, generally
necessary to lead to analytical expressions in order to study the
different characteristics of the electronic silicon-based devices.
Further progress in the development, design and optimization of
Silicon-based devices necessarily requires new theory and modeling
tools. In our study, we use the PSO (Particle Swarm Optimization)
technique as a computational tool to develop analytical approaches in
order to study the transport phenomenon of the electron in crystalline
silicon as function of temperature and doping concentration. Good
agreement between our results and measured data has been found.
The optimized analytical models can also be incorporated into the
circuits simulators to study Si-based devices without impact on the
computational time and data storage.
Abstract: The algorithm represents the DCT coefficients to concentrate signal energy and proposes combination and dictator to eliminate the correlation in the same level subband for encoding the DCT-based images. This work adopts DCT and modifies the SPIHT algorithm to encode DCT coefficients. The proposed algorithm also provides the enhancement function in low bit rate in order to improve the perceptual quality. Experimental results indicate that the proposed technique improves the quality of the reconstructed image in terms of both PSNR and the perceptual results close to JPEG2000 at the same bit rate.
Abstract: This paper proposes a modeling methodology for the
development of data analysis solution. The Author introduce the
approach to address data warehousing issues at the at enterprise level.
The methodology covers the process of the requirements eliciting and
analysis stage as well as initial design of data warehouse. The paper
reviews extended business process model, which satisfy the needs of
data warehouse development. The Author considers that the use of
business process models is necessary, as it reflects both enterprise
information systems and business functions, which are important for
data analysis. The Described approach divides development into
three steps with different detailed elaboration of models. The
Described approach gives possibility to gather requirements and
display them to business users in easy manner.
Abstract: The dynamic behaviour of a four-bar linkage driven by a velocity controlled DC motor is discussed in the paper. In particular the author presents the results obtained by means of a specifically developed software, which implements the mathematical models of all components of the system (linkage, transmission, electric motor, control devices). The use of this software enables a more efficient design approach, since it allows the designer to check, in a simple and immediate way, the dynamic behaviour of the mechanism, arising from different values of the system parameters.
Abstract: In designing of condensers, the prediction of pressure
drop is as important as the prediction of heat transfer coefficient.
Modeling of two phase flow, particularly liquid – vapor flow under
diabatic conditions inside a horizontal tube using CFD analysis is
difficult with the available two phase models in FLUENT due to
continuously changing flow patterns. In the present analysis, CFD
analysis of two phase flow of refrigerants inside a horizontal tube of
inner diameter, 0.0085 m and 1.2 m length is carried out using
homogeneous model under adiabatic conditions. The refrigerants
considered are R22, R134a and R407C. The analysis is performed at
different saturation temperatures and at different flow rates to
evaluate the local frictional pressure drop. Using Homogeneous
model, average properties are obtained for each of the refrigerants
that is considered as single phase pseudo fluid. The so obtained
pressure drop data is compared with the separated flow models
available in literature.
Abstract: This paper introduces a new digital logic design, which
combines the DSP and FPGA to implement the conventional DTC of
induction machine. The DSP will be used for floating point
calculation whereas the FPGA main task is to implement the
hysteresis-based controller. The emphasis is on FPGA digital logic
design. The simulation and experimental results are presented and
summarized.
Abstract: A active inductor in CMOS techonology with a supply voltage of 1.8V is presented. The value of the inductance L can be in the range from 0.12nH to 0.25nH in high frequency(HF). The proposed active inductor is designed in TSMC 0.18-um CMOS technology. The power dissipation of this inductor can retain constant at all operating frequency bands and consume around 20mW from 1.8V power supply. Inductors designed by integrated circuit occupy much smaller area, for this reason,attracted researchers attention for more than decade. In this design we used Advanced Designed System (ADS) for simulating cicuit.
Abstract: Recently, wireless sensor networks have been paid
more interest, are widely used in a lot of commercial and military
applications, and may be deployed in critical scenarios (e.g. when a
malfunctioning network results in danger to human life or great
financial loss). Such networks must be protected against human
intrusion by using the secret keys to encrypt the exchange messages
between communicating nodes. Both the symmetric and asymmetric
methods have their own drawbacks for use in key management. Thus,
we avoid the weakness of these two cryptosystems and make use of
their advantages to establish a secure environment by developing the
new method for encryption depending on the idea of code
conversion. The code conversion-s equations are used as the key for
designing the proposed system based on the basics of logic gate-s
principals. Using our security architecture, we show how to reduce
significant attacks on wireless sensor networks.
Abstract: carbonylation of methanol in homogenous phase is
one of the major routesfor production of acetic acid. Amongst group
VIII metal catalysts used in this process iridium has displayed the
best capabilities. To investigate effect of operating parameters like:
temperature, pressure, methyl iodide, methyl acetate, iridium,
ruthenium, and water concentrations on the reaction rate,
experimental design for this system based upon central composite
design (CCD) was utilized. Statistical rate equation developed by this
method contained individual, interactions and curvature effects of
parameters on the reaction rate. The model with p-value less than
0.0001 and R2 values greater than 0.9; confirmeda satisfactory fitness
of the experimental and theoretical studies. In other words, the
developed model and experimental data obtained passed all
diagnostic tests establishing this model as a statistically significant.