Abstract: Column leach test has been performed to examine the
behavior of leaching of sodium, calcium and potassium in landfills.
In the column leach apparatus, two different layers of contaminated
and uncontaminated soils of different height ratios (ratio of depth of
contaminated soil to the depth of uncontaminated soil) are taken.
Water is poured from an overhead tank at a particular flowrate to the
inlet of the soil column for a certain ponding depth over the
contaminated soil. Subsequent infiltration causes leaching and the
leachates are collected from the bottom of the column. The
concentrations of Na, Ca and K in the leachate are measured using
flame photometry. The experiments are further extended by changing
the rates of flow from the overhead tank to the inlet of the column in
achieving the same ponding depth. The experiments are performed
for different scenarios in which the height ratios are altered and the
variations of concentrations of Na, Ca, and K are observed. The study
brings an estimation of leaching in landfill sites for different heights
and precipitation intensity where a ponding depth is maintained over
the landfill. It has been observed that the leaching behavior of Na,
Ca, and K are not similar. Calcium exhibits highest amount of
leaching compared to Sodium and Potassium under similar
experimental conditions.
Abstract: In this paper, we propose the pre-processor based on
the Evidence Supporting Measure of Similarity (ESMS) filter and also
propose the unified fusion approach (UFA) based on the general
fusion machine coupled with ESMS filter, which improve the
correctness and precision of information fusion in any fields of
application. Here we mainly apply the new approach to Simultaneous
Localization And Mapping (SLAM) of Pioneer II mobile robots. A
simulation experiment was performed, where an autonomous virtual
mobile robot with sonar sensors evolves in a virtual world map with
obstacles. By comparing the result of building map according to the
general fusion machine (here DSmT-based fusing machine and
PCR5-based conflict redistributor considereded) coupling with ESMS
filter and without ESMS filter, it shows the benefit of the selection of
the sources as a prerequisite for improvement of the information
fusion, and also testifies the superiority of the UFA in dealing with
SLAM.
Abstract: Acoustic Imaging based sound localization using microphone
array is a challenging task in digital-signal processing.
Discrete Fourier transform (DFT) based near-field acoustical holography
(NAH) is an important acoustical technique for sound source
localization and provide an efficient solution to the ill-posed problem.
However, in practice, due to the usage of small curtailed aperture
and its consequence of significant spectral leakage, the DFT could
not reconstruct the active-region-of-sound (AROS) effectively, especially
near the edges of aperture. In this paper, we emphasize the
fundamental problems of DFT-based NAH, provide a solution to
spectral leakage effect by the extrapolation based on linear predictive
coding and 2D Tukey windowing. This approach has been tested to
localize the single and multi-point sound sources. We observe that
incorporating extrapolation technique increases the spatial resolution,
localization accuracy and reduces spectral leakage when small curtail
aperture with a lower number of sensors accounts.
Abstract: In this study it is aimed to determine the level of preservice teachers- computer phobia. Whether or not computer phobia meaningfully varies statistically according to gender and computer experience has been tested in the study. The study was performed on 430 pre-service teachers at the Education Faculty in Rize/Turkey. Data in the study were collected through the Computer Phobia Scale consisting of the “Personal Knowledge Questionnaire", “Computer Anxiety Rating Scale", and “Computer Thought Survey". In this study, data were analyzed with statistical processes such as t test, and correlation analysis. According to results of statistical analyses, computer phobia of male pre-service teachers does not statistically vary depending on their gender. Although male preservice teachers have higher computer anxiety scores, they have lower computer thought scores. It was also observed that there is a negative and intensive relation between computer experience and computer anxiety. Meanwhile it was found out that pre-service teachers using computer regularly indicated lower computer anxiety. Obtained results were tried to be discussed in terms of the number of computer classes in the Education Faculty curriculum, hours of computer class and the computer availability of student teachers.
Abstract: In this study, solid phase micro-extraction (SPME)
was optimized to improve the sensitivity and accuracy in
formaldehyde determination for plywood panels. Further work has
been carried out to compare the newly developed technique with
existing method which reacts formaldehyde collected in desiccators
with acetyl acetone reagent (DC-AA). In SPME, formaldehyde was
first derivatized with O-(2,3,4,5,6 pentafluorobenzyl)-hydroxylamine
hydrochloride (PFBHA) and analysis was then performed by gas
chromatography in combination with mass spectrometry (GC-MS).
SPME data subjected to various wood species gave satisfactory
results, with relative standard deviations (RSDs) obtained in the
range of 3.1-10.3%. It was also well correlated with DC values,
giving a correlation coefficient, RSQ, of 0.959. The quantitative
analysis of formaldehyde by SPME was an alternative in wood
industry with great potential
Abstract: The purposes of this study are to study political
information exposure, politicians- perceptions, political attitudes and
political participations among people in Bangkok Metropolitan Area.
The sample consisted of 420 which were selected by using accidental sampling method. Questionnaires were administered to all of the
respondents to obtain the data for this research. T-test, one-way ANOVA and Pearson-s correlation coefficient were used to analyze the data. The findings are as follows: The difference in gender,
education, income and occupation has significantly effect upon political information exposures. The difference in age, income has
significantly effect upon politicians- perceptions. The difference in income has significantly effect upon political attitudes. The
difference in gender, income and occupation has significantly effect
upon political participations. There were a significantly relations between political information exposures, political attitudes, political
participations and between politicians- perceptions, political attitudes and political participations.
Abstract: In the last decades, the problem of perforation
damage has been considered as the major factor for the
reduction of oil productivity. Underbalance perforation is
considered as one of the best means to minimize or overcome
this problem. By maintaining wellbore pressure lower than
formation pressure, perforation damage could be minimize or
eliminated. This can be achieved by the use of nontraditional
lightweight completion fluid. This paper presents the effect of
natural clay in formulating nontraditional completion fluid to
ensure successful perforation job and increase of production
rate. Natural clay is used as homogenizing agent to create a
stable and non-damaging low-density completion fluid.
Results indicate that the addition of natural clay dramatically
increase the stability of the final fluids. In addition, field test
has shown that the application of nontraditional completion
fluid increases oil production by three folds.
Abstract: This work aims to test the application of computational fluid dynamics (CFD) modeling to fixed bed catalytic cracking reactors. Studies of CFD with a fixed bed design commonly use a regular packing with N=2 to define bed geometry. CFD allows us to obtain a more accurate view of the fluid flow and heat transfer mechanisms present in fixed bed equipment. Naphtha was used as feedstock and the reactor length was 80cm. It is divided in three sections that catalyst bed packed in the middle section of the reactor. The reaction scheme was involved one primary reaction and 24 secondary reactions. Because of high CPU times in these simulations, parallel processing have been used. In this study the coke formation process in fixed bed and empty tube reactor was simulated and coke in these reactors are compared. In addition, the effect of steam ratio and feed flow rate on coke formation was investigated.
Abstract: The enthusiasm for gluten avoidance in a growing
market is met by improvements in sensitive detection methods for
analysing gluten content. Paradoxically, manufacturers employ no
such systems in the production process but continue to market their
product as gluten free, a significant risk posed to an undetermined
coeliac population. This paper resonates with an immunological
response that causes gastrointestinal scarring and villous atrophy with
the conventional description of personal injury. This thesis divulges
into evaluating potential inadequacies of gluten labelling laws which
not only present a diagnostic challenge for general practitioners in the
UK but it also exposes a less than adequate form of available legal
protection to those who suffer adverse reactions as a result of gluten
digestion. Central to this discussion is whether a claim brought in
misrepresentation, negligence and/or under the Consumer Protection
Act 1987 could be sustained. An interesting comparison is then made
with the legal regimes of neighboring jurisdictions furthering the
theme of a legally un-catered for gluten kingdom.
Abstract: In this paper, a post processing scheme is suggested
for improvement of Bit Error-Rate (BER) in optical fiber
transmission receivers. The developed scheme has been tested on
optical fiber systems operating with a non-return-to-zero (NRZ)
format at transmission rates of up to 10Gbps. The transmission
system considered is based on well known transmitters and receivers
blocks operating at wavelengths in the region of 1550 nm using a
standard single mode fiber. Performance of improved detected
signals has been evaluated via the analysis of quality factor and
computed bit error rates. Numerical simulations have shown a
noticeable improvement of the system BER after implementation of
the suggested post processing operation on the detected electrical
signals.
Abstract: A comprehensive program of laboratory testing on a
compacted kaolin in a modified triaxial cell was perform to
investigate the influence of hydraulic hysteresis on effective stress in
unsaturated soils. The test data are presented on a range of constant
suction shear tests along wetting and drying paths. The values of
effective stress parameter χ at different matric suction were
determined using the test results. The effect of hydraulic hysteresis
phenomenon on the effective stress was observed. The values of
effective stress parameter χ obtained from the experiments were
compared with those obtained from the expressions proposed in
literature.
Abstract: This paper describes a finite-difference time-domainFDTD) method to analyze lightning surge propagation in electric transmission lines. Numerical computation of solving the Telegraphist-s equations is determined and investigated its effectiveness. A source of lightning surge wave on power transmission lines is modeled by using Heidler-s surge model. The
proposed method was tested against medium-voltage power
transmission lines in comparison with the solution obtained by using
lattice diagram. As a result, the calculation showed that the method is one of accurate methods to analyze transient
lightning wave in power transmission lines.
Abstract: Power system stability enhancement by simultaneous tuning of a Power System Stabilizer (PSS) and a Static Var Compensator (SVC)-based controller is thoroughly investigated in this paper. The coordination among the proposed damping stabilizers and the SVC internal voltage regulators has also been taken into consideration. The design problem is formulated as an optimization problem with a time-domain simulation-based objective function and Real-Coded Genetic Algorithm (RCGA) is employed to search for optimal controller parameters. The proposed stabilizers are tested on a weakly connected power system with different disturbances and loading conditions. The nonlinear simulation results are presented to show the effectiveness and robustness of the proposed control schemes over a wide range of loading conditions and disturbances. Further, the proposed design approach is found to be robust and improves stability effectively even under small disturbance and unbalanced fault conditions.
Abstract: The main purpose of this research was to study how to communicate the identity of the Bangpoo, Samu tPrakan province for ecotourism. The qualitative data was collected through studying related materials, exploring the area, in-depth interviews with three groups of people: three directly responsible officers who were key informants of the district, twenty foreign tourists and five Thai tourist guides. A content analysis was used to analyze the qualitative data. The two main findings of the study were as follows:
The identity of Bangpoo, Samut Prakan province. This establishment was near the Mouth of the Gulf of Thailand for normal people and tourists, consisting of rest accommodations. There are restaurants where food and drinks are served, rich mangrove forests, Banpoo seaside resort and mangrove trees. Bangpoo seaside resort is characterized by muddy beacheswhere the greatest number of seagulls can be seen from March to May each year.
The communication of the identity of Bangpoo, Samut Prakan province which the researcher could find and design to present in English materials can be summed up in 3 items: 1) The history of Bangpoo, Samut Prakan province 2) The Learning center of Ecotourism: Seagulls and Mangrove forest 3) How to keep Banpoo, Samut Prakran province for ecotourism.
Abstract: Surface roughness (Ra) is one of the most important requirements in machining process. In order to obtain better surface roughness, the proper setting of cutting parameters is crucial before the process take place. This research presents the development of mathematical model for surface roughness prediction before milling process in order to evaluate the fitness of machining parameters; spindle speed, feed rate and depth of cut. 84 samples were run in this study by using FANUC CNC Milling α-Τ14ιE. Those samples were randomly divided into two data sets- the training sets (m=60) and testing sets(m=24). ANOVA analysis showed that at least one of the population regression coefficients was not zero. Multiple Regression Method was used to determine the correlation between a criterion variable and a combination of predictor variables. It was established that the surface roughness is most influenced by the feed rate. By using Multiple Regression Method equation, the average percentage deviation of the testing set was 9.8% and 9.7% for training data set. This showed that the statistical model could predict the surface roughness with about 90.2% accuracy of the testing data set and 90.3% accuracy of the training data set.
Abstract: Key management represents a major and the most
sensitive part of cryptographic systems. It includes key generation,
key distribution, key storage, and key deletion. It is also considered
the hardest part of cryptography. Designing secure cryptographic
algorithms is hard, and keeping the keys secret is much harder.
Cryptanalysts usually attack both symmetric and public key
cryptosystems through their key management. We introduce a
protocol to exchange cipher keys over insecure communication
channel. This protocol is based on public key cryptosystem,
especially elliptic curve cryptosystem. Meanwhile, it tests the cipher
keys and selects only the good keys and rejects the weak one.
Abstract: Because of the low maintenance and robustness induction motors have many applications in the industries. The speed control of induction motor is more important to achieve maximum torque and efficiency. Various speed control techniques like, Direct Torque Control, Sensorless Vector Control and Field Oriented Control are discussed in this paper. Soft computing technique – Fuzzy logic is applied in this paper for the speed control of induction motor to achieve maximum torque with minimum loss. The fuzzy logic controller is implemented using the Field Oriented Control technique as it provides better control of motor torque with high dynamic performance. The motor model is designed and membership functions are chosen according to the parameters of the motor model. The simulated design is tested using various tool boxes in MATLAB. The result concludes that the efficiency and reliability of the proposed speed controller is good.
Abstract: Internet is without any doubt the fastest and effective mean of communication making it possible to reach a great number of people in the world. It draws its base from exchange points. Indeed exchange points are used to inter-connect various Internet suppliers and operators in order to allow them to exchange traffic and it is with these interconnections that Internet made its great strides. They thus make it possible to limit the traffic delivered via the operators of transits. This limitation allows a significant improvement of the quality of service, a reduction in the latency time just as a reduction of the cost of connection for the final subscriber. Through this article we will show how the installation of an IXP allows an improvement and a diversification of the services just as a reduction of the Internet connection costs.
Abstract: This paper presents the methodology from machine
learning approaches for short-term rain forecasting system. Decision
Tree, Artificial Neural Network (ANN), and Support Vector Machine
(SVM) were applied to develop classification and prediction models
for rainfall forecasts. The goals of this presentation are to
demonstrate (1) how feature selection can be used to identify the
relationships between rainfall occurrences and other weather
conditions and (2) what models can be developed and deployed for
predicting the accurate rainfall estimates to support the decisions to
launch the cloud seeding operations in the northeastern part of
Thailand. Datasets collected during 2004-2006 from the
Chalermprakiat Royal Rain Making Research Center at Hua Hin,
Prachuap Khiri khan, the Chalermprakiat Royal Rain Making
Research Center at Pimai, Nakhon Ratchasima and Thai
Meteorological Department (TMD). A total of 179 records with 57
features was merged and matched by unique date. There are three
main parts in this work. Firstly, a decision tree induction algorithm
(C4.5) was used to classify the rain status into either rain or no-rain.
The overall accuracy of classification tree achieves 94.41% with the
five-fold cross validation. The C4.5 algorithm was also used to
classify the rain amount into three classes as no-rain (0-0.1 mm.),
few-rain (0.1- 10 mm.), and moderate-rain (>10 mm.) and the overall
accuracy of classification tree achieves 62.57%. Secondly, an ANN
was applied to predict the rainfall amount and the root mean square
error (RMSE) were used to measure the training and testing errors of
the ANN. It is found that the ANN yields a lower RMSE at 0.171 for
daily rainfall estimates, when compared to next-day and next-2-day
estimation. Thirdly, the ANN and SVM techniques were also used to
classify the rain amount into three classes as no-rain, few-rain, and
moderate-rain as above. The results achieved in 68.15% and 69.10%
of overall accuracy of same-day prediction for the ANN and SVM
models, respectively. The obtained results illustrated the comparison
of the predictive power of different methods for rainfall estimation.
Abstract: Increasing demand on the performance of Subsea
Production Systems (SPS) suggests a need for more detailed
investigation of fluid behavior taking place in subsea equipment.
Complete CFD cool down analyses of subsea equipment are very
time demanding. The objective of this paper is to investigate a
Locked CFD approach, which enables significant reduction of the
computational time and at the same time maintains sufficient
accuracy during thermal cool down simulations. The result
comparison of a dead leg simulation using the Full CFD and the three
LCFD-methods confirms the validity of the locked flow field
assumption for the selected case. For the tested case the LCFD
simulation speed up by factor of 200 results in the absolute thermal
error of 0.5 °C (3% relative error), speed up by factor of 10 keeps the
LCFD results within 0.1 °C (0.5 % relative error) comparing to the
Full CFD.