Abstract: Thailand is one of the world-s leaders of rice
producers and exporters. Farmers have to increase the rice cultivation
frequency for serving the national increasing of export-s demand. It
leads to an elimination of rice residues by open burning which is the
quickest and costless management method. The open burning of rice
residue is one of the major causes of air pollutants and greenhouse
gas (GHG) emission. Under ASEAN agreement on trans-boundary
haze, Thailand set the master plan to mitigate air pollutant emission
from open burning of agricultural residues. In this master plan,
residues incorporation is promoted as alternative management
method to open burning. However, the assessment of both options in
term of GHG emission in order to investigate their contribution to
long-term global warming is still scarce or inexistent. In this study, a
method on rice residues assessment was first developed in order to
estimate and compare GHG emissions from rice cultivation under
rice residues open burning and the case with incorporation of the
same amount of rice residues, using 2006 IPCC guidelines for
emission estimation and Life Cycle Analysis technique. The
emission from rice cultivation in different preparing area practice
was also discussed.
Abstract: The current situation in the eurozone raises a number of topics for discussion and to help in finding an answer to the question of whether a common currency is a more suitable means of coping with the impact of the financial crisis or whether national currencies are better suited to this. The economic situation in the EU is now considerably volatile and, due to problems with the fulfilment of the Maastricht convergence criteria, it is now being considered whether, in their further development, new member states will decide to distance themselves from the euro or will, in an attempt to overcome the crisis, speed up the adoption of the euro. The Czech Republic is one country with little interest in adopting the euro, justified by the fact that a better alternative to dealing with this crisis is an independent monetary policy and its ability to respond flexibly to the economic situation not only in Europe, but around the world. One attribute of the crisis in the Czech Republic and its mitigation is the freely floating exchange rate of the national currency. It is not only the Czech Republic that is attempting to alleviate the impact of the crisis, but also new EU member countries facing fresh questions to which theory have yet to provide wholly satisfactory answers. These questions undoubtedly include the problem of inflation targeting and the choice of appropriate instruments for achieving financial stability. The difficulty lies in the fact that these objectives may be contradictory and may require more than one means of achieving them. In this respect we may assume that membership of the euro zone might not in itself mitigate the development of the recession or protect the nation from future crises. We are of the opinion that the decisive factor in the development of any economy will continue to be the domestic economic policy and the operability of market economic mechanisms. We attempt to document this fact using selected countries as examples, these being the Czech Republic, Poland, Hungary, and Slovakia.
Abstract: In the modern manufacturing systems, the use of
thermal cutting techniques using oxyfuel, plasma and laser have
become indispensable for the shape forming of high quality complex
components; however, the conventional chip removal production
techniques still have its widespread space in the manufacturing
industry. Both these types of machining operations require the
positioning of end effector tool at the edge where the cutting process
commences. This repositioning of the cutting tool in every machining
operation is repeated several times and is termed as non-productive
time or airtime motion. Minimization of this non-productive
machining time plays an important role in mass production with high
speed machining. As, the tool moves from one region to the other by
rapid movement and visits a meticulous region once in the whole
operation, hence the non-productive time can be minimized by
synchronizing the tool movements. In this work, this problem is
being formulated as a general travelling salesman problem (TSP) and
a genetic algorithm approach has been applied to solve the same. For
improving the efficiency of the algorithm, the GA has been
hybridized with a noble special heuristic and simulating annealing
(SA). In the present work a novel heuristic in the combination of GA
has been developed for synchronization of toolpath movements
during repositioning of the tool. A comparative analysis of new Meta
heuristic techniques with simple genetic algorithm has been
performed. The proposed metaheuristic approach shows better
performance than simple genetic algorithm for minimization of nonproductive
toolpath length. Also, the results obtained with the help of
hybrid simulated annealing genetic algorithm (HSAGA) are also
found better than the results using simple genetic algorithm only.
Abstract: In this paper we present an extension to Vision Based
LRTA* (VLRTA*) known as Vision Based Moving Target Search
(VMTS) for capturing unknown moving target in unknown territory
with randomly generated obstacles. Target position is unknown to the
agents and they cannot predict its position using any probability
method. Agents have omni directional vision but can see in one
direction at some point in time. Agent-s vision will be blocked by the
obstacles in the search space so agent can not see through the
obstacles. Proposed algorithm is evaluated on large number of
scenarios. Scenarios include grids of sizes from 10x10 to 100x100.
Grids had obstacles randomly placed, occupying 0% to 50%, in
increments of 10%, of the search space. Experiments used 2 to 9
agents for each randomly generated maze with same obstacle ratio.
Observed results suggests that VMTS is effective in locate target
time, solution quality and virtual target. In addition, VMTS becomes
more efficient if the number of agents is increased with proportion to
obstacle ratio.
Abstract: The rheological properties of light crude oil and its mixture with water were investigated experimentally. These rheological properties include steady flow behavior, yield stress, transient flow behavior, and viscoelastic behavior. A RheoStress RS600 rheometer was employed in all of the rheological examination tests. The light crude oil exhibits a Newtonian and for emulsion exhibits a non-Newtonian shear thinning behavior over the examined shear rate range of 0.1–120 s-1. In first time, a series of samples of crude oil from the Algerian Sahara has been tested and the results expressed in terms of τ=f(γ) have demonstrated their Newtonian character for the temperature included in [20°C, 70°C]. In second time and at T=20°C, the oil-water emulsions (30%, 50% and 70%) by volume of water), thermodynamically stable, have demonstrated a non-Newtonian rheological behavior that is to say, Herschel-Bulkley and Bingham types. For each type of crude oil-water emulsion, the rheological parameters are calculated by numerical treatment of results.
Abstract: Two-dimensional finite element model was created in this work to investigate the stresses distribution within rock-like samples with offset open non-persistent joints under biaxial loading. The results of this study have explained the fracture mechanisms observed in tests on rock-like material with open non-persistent offset joints [1]. Finite element code SAP2000 was used to study the stresses distribution within the specimens. Four-nodded isoperimetric plain strain element with two degree of freedom per node, and the three-nodded constant strain triangular element with two degree of freedom per node were used in the present study.The results of the present study explained the formation of wing cracks at the tip of the joints for low confining stress as well as the formation of wing cracks at the middle of the joint for the higher confining stress. High shear stresses found in the numerical study at the tip of the joints explained the formation of secondary cracks at the tip of the joints in the experimental study. The study results coincide with the experimental observations which showed that for bridge inclination of 0o, the coalescence occurred due to shear failure and for bridge inclination of 90o the coalescence occurred due to tensile failure while for the other bridge inclinations coalescence occurred due to mixed tensile and shear failure.
Abstract: International literature emphasizes on the concern regarding the phenomenon of aggression in hospital. This paper focuses on the reality of aggressive interactions reigning within an emergency triage involving three chaps of protagonists: the professionals, the patients and their carers. The data collection was made from a grid of observation, in which the various variables exposed in the literature were integrated. They observations took place around the clock, for three weeks, at the rate of one week a month. In this research 331 aggressive interactions have been listed and analyzed by means of the software SPSS. This research is one of the very few continuous observation surveys in the literature. It shows the various human factors at play in the emergence of aggressive interaction. The data may be used both for taking steps in primary prevention, thanks to the analysis of interaction modes, and in secondary prevention by integrating the useful results in situational prevention.
Abstract: In the present study, the effects of ultrasound as
emerging technology were investigated on germination stimulation,
amount of alpha-amylase activity on dry barley seeds before steeping
stage of malting process. All experiments were carried out at 20 KHz
on the ultrasonic generator in 3 different ultrasonic intensities (20, 60
and 100% setting from total power of device) and time (5, 10 and 15
min) at constant temperature (30C). For determining the effects of
these parameters on enzyme the Fuwa method assay based on the
decreased staining value of blue starch–iodine complexes employed
for measurement an activity. The results of these assays were
analyzed by Qualitek4 software using the Taguchi statistical method
to evaluate the factor-s effects on enzyme activity. It has been found
that when malting barley is irradiated with an ultrasonic power, a
stimulating effect occurs as to the enzyme activity.
Abstract: The choice of finite element to use in order to predict
nonlinear static or dynamic response of complex structures becomes
an important factor. Then, the main goal of this research work is to
focus a study on the effect of the in-plane rotational degrees of
freedom in linear and geometrically non linear static and dynamic
analysis of thin shell structures by flat shell finite elements. In this
purpose: First, simple triangular and quadrilateral flat shell finite
elements are implemented in an incremental formulation based on the
updated lagrangian corotational description for geometrically
nonlinear analysis. The triangular element is a combination of DKT
and CST elements, while the quadrilateral is a combination of DKQ
and the bilinear quadrilateral membrane element. In both elements,
the sixth degree of freedom is handled via introducing fictitious
stiffness. Secondly, in the same code, the sixth degrees of freedom in
these elements is handled differently where the in-plane rotational
d.o.f is considered as an effective d.o.f in the in-plane filed
interpolation. Our goal is to compare resulting shell elements. Third,
the analysis is enlarged to dynamic linear analysis by direct
integration using Newmark-s implicit method. Finally, the linear
dynamic analysis is extended to geometrically nonlinear dynamic
analysis where Newmark-s method is used to integrate equations of
motion and the Newton-Raphson method is employed for iterating
within each time step increment until equilibrium is achieved. The
obtained results demonstrate the effectiveness and robustness of the
interpolation of the in-plane rotational d.o.f. and present deficiencies
of using fictitious stiffness in dynamic linear and nonlinear analysis.
Abstract: The aim of this paper is to study the oblique
stagnation point flow on vertical plate with uniform surface heat flux
in presence of magnetic field. Using Stream function, partial
differential equations corresponding to the momentum and energy
equations are converted into non-linear ordinary differential
equations. Numerical solutions of these equations are obtained using
Runge-Kutta Fehlberg method with the help of shooting technique.
In the present work the effects of striking angle, magnetic field
parameter, Grashoff number, the Prandtl number on velocity and heat
transfer characteristics have been discussed. Effect of above
mentioned parameter on the position of stagnation point are also
studied.
Abstract: In this paper, a Smart Home Service Robot, McBot II,
which performs mess-cleanup function etc. in house, is designed much
more optimally than other service robots. It is newly developed in
much more practical system than McBot I which we had developed
two years ago. One characteristic attribute of mobile platforms
equipped with a set of dependent wheels is their omni- directionality
and the ability to realize complex translational and rotational
trajectories for agile navigation in door. An accurate coordination of
steering angle and spinning rate of each wheel is necessary for a
consistent motion. This paper develops trajectory controller of
3-wheels omni-directional mobile robot using fuzzy azimuth estimator.
A specialized anthropomorphic robot manipulator which can be
attached to the housemaid robot McBot II, is developed in this paper.
This built-in type manipulator consists of both arms with 3 DOF
(Degree of Freedom) each and both hands with 3 DOF each. The
robotic arm is optimally designed to satisfy both the minimum
mechanical size and the maximum workspace. Minimum mass and
length are required for the built-in cooperated-arms system. But that
makes the workspace so small. This paper proposes optimal design
method to overcome the problem by using neck joint to move the arms
horizontally forward/backward and waist joint to move them
vertically up/down. The robotic hand, which has two fingers and a
thumb, is also optimally designed in task-based concept. Finally, the
good performance of the developed McBot II is confirmed through
live tests of the mess-cleanup task.
Abstract: The incidence of oral cancer in Taiwan increased year
by year. It replaced the nasopharyngeal as the top incurrence among
head and neck cancers since 1994. Early examination and earlier
identification for earlier treatment is the most effective medical
treatment for these cancers. Although the government fully subsidized
the expenses with tremendous promotion program for oral cancer
screening, the citizen-s participation remained low. Purpose of this
study is to understand the factors affecting the citizens- behavior
intensions of taking an oral cancer screening. Based on the Theory of
Planned Behavior, this study adopted four distinctive variables in
explaining the captioned behavior intentions.700 questionnaires were
dispatched with 500 valid responses or 71.4% returned by the citizens
with an age 30 or above from the eastern counties of Taiwan. Test
results has shown that attitude toward, subjective norms of, and
perceived behavioral control over the oral cancer screening varied
from some demographic factors to another. The study proofed that
attitude toward, subjective norms of, and perceived behavioral control
over the oral cancer screening had positive impacts on the
corresponding behavior intention. The test concluded that the theory
of planned behavior was appropriate as a theoretical framework in
explaining the influencing factors of intentions of taking oral cancer
screening. This study suggested the healthcare professional should
provide high accessibility of screening services other than just
delivering knowledge on oral cancer to promote the citizens-
intentions of taking the captioned screening. This research also
provided a practical implication to the healthcare professionals when
formulating and implementing promotion instruments for lifting the
screening rate of oral cancer.
Abstract: In recent years with the rapid development of Internet and the Web, more and more web applications have been deployed in many fields and organizations such as finance, military, and government. Together with that, hackers have found more subtle ways to attack web applications. According to international statistics, SQL Injection is one of the most popular vulnerabilities of web applications. The consequences of this type of attacks are quite dangerous, such as sensitive information could be stolen or authentication systems might be by-passed. To mitigate the situation, several techniques have been adopted. In this research, a security solution is proposed using Artificial Neural Network to protect web applications against this type of attacks. The solution has been experimented on sample datasets and has given promising result. The solution has also been developed in a prototypic web application firewall called ANNbWAF.
Abstract: Road industry has challenged the prospect of ecoconstruction. Pavements may fit within the framework of sustainable development. Hence, research implements assessments of conventional pavements impacts on environment in use of life cycle approach. To meet global, and often national, targets on pollution control, newly introduced pavement designs are under study. This is the case of Cyprus demonstration, which occurred within EcoLanes project work. This alternative pavement differs on concrete layer reinforced with tire recycling product. Processing of post-consumer tires produces steel fibers improving strength capacity against cracking. Thus maintenance works are relevantly limited in comparison to flexible pavement. This enables to be more ecofriendly, referenced to current study outputs. More specific, proposed concrete pavement life cycle processes emits 15 % less air pollutants and consumes 28 % less embodied energy than those of the asphalt pavement. In addition there is also a reduction on costs by 0.06 %.
Abstract: Partial combustion of biomass in the gasifier generates producer gas that can be used for heating purposes and as supplementary or sole fuel in internal combustion engines. In this study, the virgin biomass obtained from hingan shell is used as the feedstock for gasifier to generate producer gas. The gasifier-engine system is operated on diesel and on esters of vegetable oil of hingan in liquid fuel mode operation and then on liquid fuel and producer gas combination in dual fuel mode operation. The performance and emission characteristics of the CI engine is analyzed by running the engine in liquid fuel mode operation and in dual fuel mode operation at different load conditions with respect to maximum diesel savings in the dual fuel mode operation. It was observed that specific energy consumption in the dual fuel mode of operation is found to be in the higher side at all load conditions. The brake thermal efficiency of the engine using diesel or hingan oil methyl ester (HOME) is higher than that of dual fuel mode operation. A diesel replacement in the tune of 60% in dual fuel mode is possible with the use of hingan shell producer gas. The emissions parameters such CO, HC, NOx, CO2 and smoke are higher in the case of dual fuel mode of operation as compared to that of liquid fuel mode.
Abstract: In this paper, we propose a geometric modeling of
illumination on the patterned image containing etching transistor. This
image is captured by a commercial camera during the inspection of
a TFT-LCD panel. Inspection of defect is an important process in the
production of LCD panel, but the regional difference in brightness,
which has a negative effect on the inspection, is due to the uneven
illumination environment. In order to solve this problem, we present
a geometric modeling of illumination consisting of an interpolation
using the least squares method and 3D modeling using bezier surface.
Our computational time, by using the sampling method, is shorter
than the previous methods. Moreover, it can be further used to correct
brightness in every patterned image.
Abstract: Majority of pepper farmers in Malaysia are using the
open-sun method for drying the pepper berries. This method is time
consuming and exposed the berries to rain and contamination. A
maintenance-friendly and properly enclosed dryer is therefore
desired. A dryer design with a solar collector and a chimney was
studied and adapted to suit the needs of small-scale pepper farmers in
Malaysia. The dryer will provide an environment with an optimum
operating temperature meant for drying pepper berries. The dryer
model was evaluated by using commercially available computational
fluid dynamic (CFD) software in order to understand the heat and
mass transfer inside the dryer. Natural convection was the only mode
of heat transportation considered in this study as in accordance to the
idea of having a simple and maintenance-friendly design. To
accommodate the effect of low buoyancy found in natural convection
driers, a biomass burner was integrated into the solar dryer design.
Abstract: This paper presents an application of 5S lean technology to a production facility. Due to increased demand, high product variety, and a push production system, the plant has suffered from excessive wastes, unorganized workstations, and unhealthy work environment. This has translated into increased production cost, frequent delays, and low workers morale. Under such conditions, it has become difficult, if not impossible, to implement effective continuous improvement studies. Hence, the lean project is aimed at diagnosing the production process, streamlining the workflow, removing/reducing process waste, cleaning the production environment, improving plant layout, and organizing workstations. 5S lean technology is utilized for achieving project objectives. The work was a combination of both culture changes and tangible/physical changes on the shop floor. The project has drastically changed the plant and developed the infrastructure for a successful implementation of continuous improvement as well as other best practices and quality initiatives.
Abstract: To reduce the carbon dioxide emission into the
atmosphere, adsorption is believed to be one of the most attractive
methods for post-combustion treatment of flue gas. In this work,
activated carbon (AC) was modified by polyethylenimine (PEI) via
impregnation in order to enhance CO2 adsorption capacity. The
adsorbents were produced at 0.04, 0.16, 0.22, 0.25, and 0.28 wt%
PEI/AC. The adsorption was carried out at a temperature range from
30 °C to 75 °C and five different gas pressures up to 1 atm. TG-DTA,
FT-IR, UV-visible spectrometer, and BET were used to characterize
the adsorbents. Effects of PEI loading on the AC for the CO2
adsorption were investigated. Effectiveness of the adsorbents on the
CO2 adsorption including CO2 adsorption capacity and adsorption
temperature was also investigated. Adsorption capacities of CO2 were
enhanced with the increase in the amount of PEI from 0.04 to 0.22
wt% PEI before the capacities decreased onwards from0.25 wt% PEI
at 30 °C. The 0.22 wt% PEI/AC showed higher adsorption capacity
than the AC for adsorption at 50 °C to 75 °C.
Abstract: This paper illustrates the use of a combined neural
network model for classification of electrocardiogram (ECG) beats.
We present a trainable neural network ensemble approach to develop
customized electrocardiogram beat classifier in an effort to further
improve the performance of ECG processing and to offer
individualized health care.
We process a three stage technique for detection of premature
ventricular contraction (PVC) from normal beats and other heart
diseases. This method includes a denoising, a feature extraction and a
classification. At first we investigate the application of stationary
wavelet transform (SWT) for noise reduction of the
electrocardiogram (ECG) signals. Then feature extraction module
extracts 10 ECG morphological features and one timing interval
feature. Then a number of multilayer perceptrons (MLPs) neural
networks with different topologies are designed.
The performance of the different combination methods as well as
the efficiency of the whole system is presented. Among them,
Stacked Generalization as a proposed trainable combined neural
network model possesses the highest recognition rate of around 95%.
Therefore, this network proves to be a suitable candidate in ECG
signal diagnosis systems. ECG samples attributing to the different
ECG beat types were extracted from the MIT-BIH arrhythmia
database for the study.