Abstract: Thermoacoustic instabilities in combustors have
remained a topic of investigation for over a few decades due to the
challenges it posses to the operation of low emission gas turbines.
For combustors burning liquid fuel, understanding the cause-andeffect
relationship between spray combustion dynamics and
thermoacoustic oscillations is imperative for the successful
development of any control methodology for its mitigation. The
paper presents some very unique operating characteristics of a
kerosene-fueled diffusion type combustor undergoing limit-cycle
oscillations. Combustor stability limits were mapped using three
different-sized injectors. The results show that combustor instability
depends on the characteristics of the fuel spray. A simple analytic
analysis is also reported in support of a plausible explanation for the
unique combustor behavior. The study indicates that high amplitude
acoustic pressure in the combustor may cause secondary breakdown
of fuel droplets resulting in premixed pre-vaporized type burning of
the diffusion type combustor.
Abstract: CO2 is the primary anthropogenic greenhouse gas,
accounting for 77% of the human contribution to the greenhouse
effect in 2004. In the recent years, global concentration of CO2 in the
atmosphere is increasing rapidly. CO2 emissions have an impact on
global climate change. Anthropogenic CO2 is emitted primarily from
fossil fuel combustion. Carbon capture and storage (CCS) is one
option for reducing CO2 emissions. There are three major approaches
for CCS: post-combustion capture, pre-combustion capture and
oxyfuel process. Post-combustion capture offers some advantages as
existing combustion technologies can still be used without radical
changes on them.
There are several post combustion gas separation and capture
technologies being investigated, namely; (a) absorption, (b)
cryogenic separation, (c) membrane separation (d) micro algal biofixation
and (e) adsorption. Apart from establishing new techniques,
the exploration of capture materials with high separation performance
and low capital cost are paramount importance. However, the
application of adsorption from either technology, require easily
regenerable and durable adsorbents with a high CO2 adsorption
capacity. It has recently been reported that the cost of the CO2
capture can be reduced by using this technology. In this paper, the
research progress (from experimental results) in adsorbents for CO2
adsorption, storage, and separations were reviewed and future
research directions were suggested as well.
Abstract: Climate change and environmental pressures are
major international issues nowadays. It is time when governments,
businesses and consumers have to respond through more
environmentally friendly and aware practices, products and policies.
This is the prime time to develop alternative sustainable construction
materials, reduce greenhouse gas emissions, save energy, look to
renewable energy sources and recycled materials, and reduce waste.
The utilization of waste materials (slag, fly ash, glass beads, plastic
and so on) in concrete manufacturing is significant due to its
engineering, financial, environmental and ecological benefits. Thus,
utilization of waste materials in concrete production is very much
helpful to reach the goal of the sustainable construction. Therefore,
this study intends to use glass beads in concrete production.
The paper reports on the performance of 9 different concrete
mixes containing different ratios of glass crushed to 5 mm - 20 mm
maximum size and glass marble of 20 mm size as coarse aggregate.
Ordinary Portland cement type 1 and fine sand less than 0.5 mm were
used to produce standard concrete cylinders. Compressive strength
tests were carried out on concrete specimens at various ages. Test
results indicated that the mix having the balanced ratio of glass beads
and round marbles possess maximum compressive strength which is
3889 psi, as glass beads perform better in bond formation but have
lower strength, on the other hand marbles are strong in themselves
but not good in bonding. These mixes were prepared following a
specific W/C and aggregate ratio; more strength can be expected to
achieve from different W/C, aggregate ratios, adding admixtures like
strength increasing agents, ASR inhibitor agents etc.
Abstract: The activities which are mostly related to the environmental performance need to be pointed, especially how logistics systems influence on environmental performance. This paper analyses how company could lead the initiative in this area by incorporating environmental management principles into their daily activities. The analysis is based on literature review about logistics and environment, the information from company R website as well as face-to-face interviews. A case study is given to show how they can turn practices into green while simultaneously meet the efficiency objectives. The research results show that the adoption of EMS and ISO 14001 certification is an effective tool for the logistics management. Such practices simultaneously reduce the negative contribute to better company performance. The results also show that the emissions to air and water, and energy consumption are the main logistics impacts to the environment.
Abstract: This paper presents an efficient emission constrained
hydrothermal scheduling algorithm that deals with nonlinear
functions such as the water discharge characteristics, thermal cost,
and transmission loss. It is then incorporated into the hydrothermal
coordination program. The program has been tested on a practical
utility system having 32 thermal and 12 hydro generating units. Test
results show that a slight increase in production cost causes a
substantial reduction in emission.
Abstract: The electrolyte stirring method of anodization etching
process for manufacturing porous silicon (PS) is reported in this work.
Two experimental setups of nature air stirring (PS-ASM) and
electrolyte stirring (PS-ESM) are employed to clarify the influence of
stirring mechanisms on electrochemical etching process. Compared to
traditional fabrication without any stirring apparatus (PS-TM), a large
plateau region of PS surface structure is obtained from samples with
both stirring methods by the 3D-profiler measurement. Moreover, the
light emission response is also improved by both proposed electrolyte
stirring methods due to the cycling force in electrolyte could
effectively enhance etch-carrier distribution while the electrochemical
etching process is made. According to the analysis of statistical
calculation of photoluminescence (PL) intensity, lower standard
deviations are obtained from PS-samples with studied stirring methods,
i.e. the uniformity of PL-intensity is effectively improved. The
calculated deviations of PL-intensity are 93.2, 74.5 and 64,
respectively, for PS-TM, PS-ASM and PS-ESM.
Abstract: In order to meet the limits imposed on automotive
emissions, engine control systems are required to constrain air/fuel
ratio (AFR) in a narrow band around the stoichiometric value, due to
the strong decay of catalyst efficiency in case of rich or lean mixture.
This paper presents a model of a sample spark ignition engine and
demonstrates Simulink-s capabilities to model an internal combustion
engine from the throttle to the crankshaft output. We used welldefined
physical principles supplemented, where appropriate, with
empirical relationships that describe the system-s dynamic behavior
without introducing unnecessary complexity. We also presents a PID
tuning method that uses an adaptive fuzzy system to model the
relationship between the controller gains and the target output
response, with the response specification set by desired percent
overshoot and settling time. The adaptive fuzzy based input-output
model is then used to tune on-line the PID gains for different
response specifications. Experimental results demonstrate that better
performance can be achieved with adaptive fuzzy tuning relative to
similar alternative control strategies. The actual response
specifications with adaptive fuzzy matched the desired response
specifications.
Abstract: Electric vehicle (EV) is one of the effective solutions to
control emission of greenhouses gases in the world. It is of interest
for future transportation due to its sustainability and efficiency by
automotive manufacturers. Various electrical motors have been used
for propulsion system of electric vehicles in last decades. In this
paper brushed DC motor, Induction motor (IM), switched reluctance
motor (SRM) and brushless DC motor (BLDC) are simulated and
compared. BLDC motor is recommended for high performance
electric vehicles. PWM switching technique is implemented for speed
control of BLDC motor. Behavior of different modes of PWM speed
controller of BLDC motor are simulated in MATLAB/SIMULINK.
BLDC motor characteristics are compared and discussed for various
PWM switching modes under normal and inverter fault conditions.
Comparisons and discussions are verified through simulation results.
Abstract: In this study acoustic emission (AE) signals obtained during deformation and fracture of two types of ferrite-martensite dual phase steels (DPS) specimens have been analyzed in frequency domain. For this reason two low carbon steels with various amounts of carbon were chosen, and intercritically heat treated. In the introduced method, identifying the mechanisms of failure in the various phases of DPS is done. For this aim, AE monitoring has been used during tensile test of several DPS with various volume fraction of the martensite (VM) and attempted to relate the AE signals and failure mechanisms in these steels. Different signals, which referred to 2-3 micro-mechanisms of failure due to amount of carbon and also VM have been seen. By Fast Fourier Transformation (FFT) of signals in distinct locations, an excellent relationship between peak frequencies in these areas and micro-mechanisms of failure were seen. The results were verified by microscopic observations (SEM).
Abstract: Greenhouse gases (GHG) emissions impose major
threat to global warming potential (GWP). Unfortunately
manufacturing sector is one of the major sources that contribute
towards the rapid increase in greenhouse gases (GHG) emissions. In
manufacturing sector electric power consumption is the major driver
that influences CO2 emission. Titanium alloys are widely utilized in
aerospace, automotive and petrochemical sectors because of their
high strength to weight ratio and corrosion resistance. Titanium
alloys are termed as difficult to cut materials because of their poor
machinability rating. The present study analyzes energy consumption
during cutting with reference to material removal rate (MRR).
Surface roughness was also measured in order to optimize energy
consumption.
Abstract: The Mahin area is a part of Tarom- Hashtjin zone that
located in west of Qazvin province in northwest of Iran. Many copper
and base metals ore deposits are hosted by this zone. High potential
localities identification in this area is very necessary. The objective of
this research, is finding hydrothermal alteration zones by remote
sensing methods and best processing technique of Advanced
Spaceborne Thermal Emission and Reflection Radiometer (ASTER)
data. Different methods such as band ratio, Principal Component
Analysis (PCA), Minimum Noise Fraction (MNF) and Least Square
Fit (LS-Fit) were used for mapping hydrothermal alteration zones.
Abstract: Due to heightened concerns over environmental and economic issues the growing important of air pollution, and the importance of conserving fossil fuel resources in the world, the automotive industry is now forced to produce more fuel efficient, low emission vehicles and new drive system technologies. One of the most promising technologies to receive attention is the hybrid electric vehicle (HEV), which consists of two or more energy sources that supply energy to electric traction motors that in turn drive the wheels. This paper presents the various structures of HEV systems, the basic theoretical knowledge for describing their operation and the general behaviour of the HEV in acceleration, cruise and deceleration phases. The conventional design and sizing of a series HEV is studied. A conventional bus and its series configuration are defined and evaluated using the ADVISOR. In this section the simulation of a standard driving cycle and prediction of its fuel consumption and emissions of the HEV are discussed. Finally the bus performance is investigated to establish whether it can satisfy the performance, fuel consumption and emissions requested. The validity of the simulation has been established by the close conformity between the fuel consumption of the conventional bus reported by the manufacturer to what has achieved from the simulation.
Abstract: In this study, the Scots pine (Pinus sylvestris L.) C
needles (i.e. the current-year-needles) were used as bioindicators in
determining the aerial distribution pattern of sulphur emissions
around industrial point sources at Kemi, Northern Finland. The
average sulphur concentration in the C needles was 897 mg/kg
(d.w.), with a standard deviation of 118 mg/kg (d.w.) and range 740 –
1350 mg/kg (d.w.). According to results in this study, Scots pine
needles (Pinus sylvestris L.) appear to be an ideal bioindicators for
identifying atmospheric sulphur pollution derived from industrial
plants and can complement the information provided by plant
mapping studies around industrial plants.
Abstract: In this study, effects of EGR on CO and HC emissions
of a dual fuel HCCI-DI engine are investigated. Tests were
conducted on a single-cylinder variable compression ratio (VCR)
diesel engine with compression ratio of 17.5. Premixed gasoline is
provided by a carburetor connected to intake manifold and equipped
with a screw to adjust premixed air-fuel ratio, and diesel fuel is
injected directly into the cylinder through an injector at pressure of
250 bars. A heater placed at inlet manifold is used to control the
intake charge temperature. Optimal intake charge temperature was
110-115ºC due to better formation of a homogeneous mixture
causing HCCI combustion. Timing of diesel fuel injection has a great
effect on stratification of in-cylinder charge in HCCI combustion.
Experiments indicated 35 BTDC as the optimum injection timing.
Coolant temperature was maintained 50ºC during the tests. Results
show that increasing engine speed at a constant EGR rate leads to
increase in CO and UHC emissions due to the incomplete
combustion caused by shorter combustion duration and less
homogeneous mixture. Results also show that increasing EGR
reduces the amount of oxygen and leads to incomplete combustion
and therefore increases CO emission due to lower combustion
temperature. HC emission also increases as a result of lower
combustion temperatures.
Abstract: This paper proposes and analyses the wireless
telecommunication system with multiple antennas to the emission
and reception MIMO (multiple input multiple output) with space
diversity in a OFDM context. In particular it analyses the
performance of a DTT (Digital Terrestrial Television) broadcasting
system that includes MIMO-OFDM techniques. Different
propagation channel models and configurations are considered for
each diversity scheme. This study has been carried out in the context
of development of the next generation DVB-T/H and WRAN.
Abstract: There are many sources trough which the soil get
enriched and contaminated with REEs. The determination of REEs in
environmental samples has been limited because of the lack of
sensitive analytical techniques. Soil samples were collected from
four sites including open cast coal mine, natural coal burning, coal
washery and control in the coal field located in Dhanbad, India.
Total concentrations of rare earth elements (REEs) were determined
using the inductively coupled plasma atomic absorption spectrometry
in order to assess enrichment status in the coal field. Results showed
that the mean concentrations of La, Pr, Eu, Tb, Ho, and Tm in open
cast mine and natural coal burning sites were elevated compared to
the reference concentrations, while Ce, Nd, Sm, and Gd were
elevated in coal washery site. When compared to reference soil,
heavy REEs (HREEs) were enriched in open cast mines and natural
coal burning affected soils, however, the HREEs were depleted in the
coal washery sites. But, the Chondrite-normalization diagram showed
significant enrichment for light REEs (LREEs) in all the soils. High
concentration of Pr, Eu, Tb, Ho, Tm, and Lu in coal mining and coal
burning sites may pose human health risks. Factor analysis showed
that distribution and relative abundance of REEs of the coal washery
site is comparable with the control. Eventually washing or cleaning
of coal could significantly decrease the emission of REEs from coal
into the environment.
Abstract: Reinforced Concrete (RC) structures strengthened
with fiber reinforced polymer (FRP) lack in thermal resistance under
elevated temperatures in the event of fire. This phenomenon led to
the lining of strengthened concrete with thin high performance
cementitious composites (THPCC) to protect the substrate against
elevated temperature. Elevated temperature effects on THPCC, based
on different cementitious materials have been studied in the past but
high-alumina cement (HAC)-based THPCC have not been well
characterized. This research study will focus on the THPCC based on
HAC replaced by 60%, 70%, 80% and 85% of ground granulated
blast furnace slag (GGBS). Samples were evaluated by the
measurement of their mechanical strength (28 & 56 days of curing)
after exposed to 400°C, 600°C and 28°C of room temperature for
comparison and corroborated by their microstructure study. Results
showed that among all mixtures, the mix containing only HAC
showed the highest compressive strength after exposed to 600°C as
compared to other mixtures. However, the tensile strength of THPCC
made of HAC and 60% GGBS content was comparable to the
THPCC with HAC only after exposed to 600°C. Field emission
scanning electron microscopy (FESEM) images of THPCC
accompanying Energy Dispersive X-ray (EDX) microanalysis
revealed that the microstructure deteriorated considerably after
exposure to elevated temperatures which led to the decrease in
mechanical strength.
Abstract: Solid waste can be considered as an urban burden or
as a valuable resource depending on how it is managed. To meet the
rising demand for energy and to address environmental concerns, a
conversion from conventional energy systems to renewable resources
is essential. For the sustainability of human civilization, an
environmentally sound and techno-economically feasible waste
treatment method is very important to treat recyclable waste. Several
technologies are available for realizing the potential of solid waste as
an energy source, ranging from very simple systems for disposing of
dry waste to more complex technologies capable of dealing with
large amounts of industrial waste. There are three main pathways for
conversion of waste material to energy: thermo chemical,
biochemical and physicochemical. This paper investigates the thermo
chemical conversion of solid waste for energy recovery. The
processes, advantages and dis-advantages of various thermo chemical
conversion processes are discussed and compared. Special attention
is given to Gasification process as it provides better solutions
regarding public acceptance, feedstock flexibility, near-zero
emissions, efficiency and security. Finally this paper presents
comparative statements of thermo chemical processes and introduces
an integrated waste management system.
Abstract: Some of the polycyclic aromatic hydrocarbons (PAHs)
are the strongest known carcinogens compounds; the majority of
them are mostly produced by the incomplete combustion of fossil
fuels; Motor vehicles are a significant source of polycyclic aromatic
hydrocarbon (PAH) where diesel emission is one of the main sources
of such compounds available in the ambient air. There is a big
concern about the increasing concentration of PAHs in the
environment. Researchers are trying to explore optimal methods to
reduce those pollutants and improve the quality of air. Water blended
fuel is one of the possible approaches to reduce emission of PAHs
from the combustion of diesel in urban and domestic vehicles. In this
work a modeling study was conducted using CHEMKIN-PRO
software to simulate spray combustion at similar diesel engine
conditions. Surrogate fuel of (80 % n-heptane and 20 % toluene) was
used due to detailed kinetic and thermodynamic data needed for
modeling is available for this kind of fuel but not available for diesel.
An emulsified fuel with 3, 5, 8, 10 and 20 % water by volume is used
as an engine feed for this study. The modeling results show that water
has a significant effect on reducing engine soot and PAHs precursors
formation up to certain extent.
Abstract: The 20th century has brought much development to the practice of Architecture worldwide, and technology has bridged inhabitation limits in many regions of the world with high levels of comfort and conveniences, most times at high costs to the environment. Throughout the globe, the tropical countries are being urbanized at an unprecedented rate and housing has become a major issue worldwide, in light of increased demand and lack of appropriate infra-structure and planning. Buildings and urban spaces designed in tropical cities have mainly adopted external concepts that in most cases do not fit the needs of the inhabitants living in such harsh climatic environment, and when they do, do so at high financial, environmental and cultural costs. Traditional architectural practices can provide valuable understanding on how self-reliance and autonomy of construction can be reinforced in rural-urban tropical environments. From traditional housing knowledge, it is possible to derive lessons for the development of new construction materials that are affordable, environmentally friendly, culturally acceptable and accesible to all.Specifically to the urban context, such solutions are of outmost importance, given the needs to a more democratic society, where access to housing is considered high in the agenda for development. Traditional or rural constructions are also ongoing through extensive changes eventhough they have mostly adopted climate-responsive building practices relying on local resources (with minimum embodied energy) and energy (for comfort and quality of life). It is important to note that many of these buildings can actually be called zero-energy, and hold potential answers to enable transition from high energy, high cost, low comfort urban habitations to zero/low energy habitations with high quality urban livelihood. Increasing access to modern urban lifestyels have also an effect on the aspirations from people in terms of performance, comfort and convenience in terms of their housing and the way it is produced and used. These aspirations are resulting in transitions from localresource dependent habitations- to non-local resource based highenergy urban style habitations. And such transitions are resulting in the habitations becoming increasingly unsuited to the local climatic conditions with increasing discomfort, ill-health, and increased CO2 emissions and local environmental disruption. This research studies one specific transition group in the context of 'water communities' in tropical-equatorial regions: Ribeirinhos housing typology (Amazonas, Brazil). The paper presents the results of a qualitative sustainability assessment of the housing typologies under transition, found at the Ribeirinhos communities.