Abstract: The effect of a 3-dimensional (3D) blade on the turbine
characteristics of Wells turbine for wave energy conversion has been
investigated experimentally by model testing under steady flow
conditions in this study, in order to improve the peak efficiency and
stall characteristics. The aim of use of 3D blade is to prevent flow
separation on the suction surface near the tip. The chord length is
constant with radius and the blade profile changes gradually from the
mean radius to tip. The proposed blade profiles in the study are
NACA0015 from the hub to mean radius and NACA0025 at the tip.
The performances of Wells turbine with 3D blades has been compared
with those of the original Wells turbine, i.e., the turbine with
2-dimensional (2D) blades. As a result, it was concluded that although
the peak efficiency of Wells turbine can be improved by the use of the
proposed 3D blade, its blade does not overcome the weakness of
stalling.
Abstract: The reliability of the filtered HVBK model is now
investigated via some large eddy simulations (LES) of freely
decaying isotropic superfluid turbulence. For homogeneous
turbulence at very high Reynolds numbers, comparison of the terms
in the spectral kinetic energy budget equation indicates, in the
energy-containing range, that the production and energy transfer
effects become significant except for dissipation. In the inertial range,
where the two fluids are perfectly locked, the mutual friction maybe
neglected with respect to other terms. Also, the LES results for the
other terms of the energy balance are presented.
Abstract: We propose a new alternative method for imposing
fluid-solid boundary conditions in simulations of Multiparticle
Collision Dynamics. Our method is based on the introduction of
an explicit potential force acting between the fluid particles and a
surface representing a solid boundary. We show that our method can
be used in simulations of plane Poiseuille flows. Important quantities
characterizing the flow and the fluid-solid interaction like the slip
coefficient at the solid boundary and the effective viscosity of the
fluid, are measured in terms of the set of independent parameters
defining the numerical implementation. We find that our method can
be used to simulate the correct hydrodynamic flow within a wide
range of values of these parameters.
Abstract: Essential oils are expensive phytochemicals produced
and extracted from specific species belonging to particular families in
the plant kingdom. In the United Arab Emirates country (UAE), is
located in the arid region of the world, nine species, from the
Lamiaceae family, having the capability to produce therapeutic grade
essential oils. These species include; Mentha spicata, Ocimum
forskolei, Salvia macrosiphon, Salvia aegyptiaca, Salvia macilenta,
Salvia spinosa, Teucrium polium, Teucrium stocksianum and Zataria
multiflora. Although, such potential species are indigenous to the
UAE, however, there are almost no studies available to investigate
the chemical composition and the quality of the extracted essential
oils under the UAE climatological conditions. Therefore, great
attention has to be given to such valuable natural resources, through
conducting highly supported research projects, tailored to the UAE
conditions, and investigating different extraction techniques,
including the application of the latest available technologies, such as
superficial fluid CO2. This is crucially needed; in order to accomplish
the greatest possibilities in the medicinal field, specifically in the
discovery of new therapeutic chemotypes, as well as, to achieve the
sustainability of this natural resource in the country.
Abstract: A computational fluid dynamics simulation is done for
non-Newtonian fluid in a baffled stirred tank. The CMC solution is
taken as non-Newtonian shear thinning fluid for simulation. The
Reynolds Average Navier Stocks equation with steady state multi
reference frame approach is used to simulate flow in the stirred tank.
The turbulent flow field is modelled using realizable k-ε turbulence
model. The simulated velocity profiles of Rushton turbine is
validated with literature data. Then, the simulated flow field of CD-6
impeller is compared with the Rushton turbine. The flow field
generated by CD-6 impeller is less in magnitude than the Rushton
turbine. The impeller global parameter, power number and flow
number, and entropy generation due to viscous dissipation rate is also
reported.
Abstract: A single-phase closed thermosyphon has been
fabricated and experimented to utilize solar energy for water heating.
The working fluid of the closed thermosyphon is heated at the flatplate
collector and the hot water goes to the water tank due to density
gradient caused by temperature differences. This experimental work
was done using insulated water tank and insulated connecting pipe
between the tank and the flat-plate collector. From the collected data,
performance parameters such as instantaneous collector efficiency
and heat removal factor are calculated. In this study, the effects of
glazing were also observed. The water temperature rise and the
maximum instantaneous efficiency obtained from this experiment
with glazing using insulated water tank and insulated connecting pipe
are 17°C in a period of 5 hours and 60% respectively. Whereas the
water temperature rise and the maximum instantaneous efficiency
obtained from this experiment with glazing using non-insulated water
tank and non-insulated connecting pipe are 14°C in a period of 5
hours and 39% respectively.
Abstract: This work presents a Computational Fluid Dynamics
(CFD) simulation of a butterfly valve used to control the flow of
combustible gas mixture in an industrial process setting.The work
uses CFD simulation to analyze the flow characteristics in the
vicinity of the valve, including the pressure distributions and
Frequency spectrum of the pressure pulsations downstream the valves
and the vortex shedding allow predicting the torque fluctuations
acting on the valve shaft and the possibility of generating mechanical
vibration and resonance.These fluctuations are due to aerodynamic
torque resulting from fluid turbulence and vortex shedding in the
valve vicinity.
The valve analyzed is located in a pipeline between two opposing
90o elbows, which exposes the valve and the surrounding structure to
the turbulence generated upstream and downstream the elbows at
either end of the pipe.CFD simulations show that the best location for
the valve from a vibration point of view is in the middle of the pipe
joining the elbows.
Abstract: Cement-based grouts has been used successfully to
repair cracks in many concrete structures such as bridges, tunnels,
buildings and to consolidate soils or rock foundations. In the present
study the rheological characterization of cement grout with
water/binder ratio (W/B) is fixed at 0.5. The effect of the replacement
of cement by bentonite (2 to 10% wt) in presence of superplasticizer
(0.5% wt) was investigated. Several rheological tests were carried out
by using controlled-stress rheometer equipped with vane geometry in
temperature of 20°C. To highlight the influence of bentonite and
superplasticizer on the rheological behavior of grout cement, various
flow tests in a range of shear rate from 0 to 200 s-1 were observed.
Cement grout showed a non-Newtonian viscosity behavior at all
concentrations of bentonite. Three parameter model Herschel-
Bulkley was chosen for fitting of experimental data. Based on the
values of correlation coefficients of the estimated parameters, The
Herschel-Bulkley law model well described the rheological behavior
of the grouts. Test results showed that the dosage of bentonite
increases the viscosity and yield stress of the system and introduces
more thixotropy. While the addition of both bentonite and
superplasticizer with cement grout improve significantly the fluidity
and reduced the yield stress due to the action of dispersion of SP.
Abstract: To mimic the natural circumstances of cell growth in an organism, we present three-dimensional (3D) scaffolds fabricated by microfluidics for cultivation. This work investigates the cellular behaviors of rat cardiomyocytes in gelatin 3D scaffolds compared to those on 2D control, such as proliferation, viability and morphology. We found that the scaffolds may induce skeletal differentiation of H9c2 cells.
Abstract: The reduction of greenhouse gases emissions is highly
discussed ecological theme at present. In addition to power industry
also main production sectors of binders, i.e. cement, air and hydraulic
lime are very sensitive to these questions. One of the possibilities
how CO2 emissions can be reduced directly at clinker burnout is
represented by partial substitution of lime with a material containing
limy ions at absence of carbonate group. Fluidised fly ash is one of
such potential raw materials where CaO can be found free and also
bound in anhydrite, CaSO4. At application of FBC (fluidized bed
combustion) fly ash with approximate 20% CaO content and its
dosing ratio to high percent lime 1:2, corresponding stechiometrically
to the preparation of raw material powder, approximately 0,37 t CO2
per 1 ton of one-component cement would be released at clinker
burnout compared to 0,46 t CO2 when orthodox raw materials are
used. The reduction of CO2 emissions thus could reach even 20%.
Abstract: The global demand for continuous and eco-friendly
renewable energy as alternative to fossils fuels is large and ever
growing in nowadays. This paper will focus on capability of Vortex
Induced Vibration (VIV) phenomenon in generating alternative
energy for offshore platform application. In order to maximize the
potential of energy generation, the effects of lock in phenomenon and
different geometries of cylinder were studied in this project. VIV is
the motion induced on bluff body which creates alternating lift forces
perpendicular to fluid flow. Normally, VIV is unwanted in order to
prevent mechanical failure of the vibrating structures. But in this
project, instead of eliminating these vibrations, VIV will be exploited
to transform these vibrations into a valuable resource of energy.
Abstract: This study aimed at designing and developing a
mechanical force gauge for the square watermelon mold for the first
time. It also tried to introduce the square watermelon characteristics
and its production limitations. The mechanical force gauge
performance and the product itself were also described. There are
three main designable gauge models: a. hydraulic gauge, b. strain
gauge, and c. mechanical gauge. The advantage of the hydraulic
model is that it instantly displays the pressure and thus the force
exerted by the melon. However, considering the inability to measure
forces at all directions, complicated development, high cost, possible
hydraulic fluid leak into the fruit chamber and the possible influence
of increased ambient temperature on the fluid pressure, the
development of this gauge was overruled. The second choice was to
calculate pressure using the direct force a strain gauge. The main
advantage of these strain gauges over spring types is their high
precision in measurements; but with regard to the lack of conformity
of strain gauge working range with water melon growth, calculations
were faced with problems. Finally the mechanical pressure gauge has
advantages, including the ability to measured forces and pressures on
the mold surface during melon growth; the ability to display the peak
forces; the ability to produce melon growth graph thanks to its
continuous force measurements; the conformity of its manufacturing
materials with the required physical conditions of melon growth; high
air conditioning capability; the ability to permit sunlight reaches the
melon rind (no yellowish skin and quality loss); fast and
straightforward calibration; no damages to the product during
assembling and disassembling; visual check capability of the product
within the mold; applicable to all growth environments (field,
greenhouses, etc.); simple process; low costs and so forth.
Abstract: Male factor infertility due to endocrine disturbances
such as abnormalities in prolactin levels are encountered in a
significant proportion. This case control study was carried out to
determine the effects of prolactin on the male reproductive tract,
using 200 male white rats. The rats were maintained as the control
group (G1), hypoprolactinaemic group (G2), 3 hyperprolactinaemic
groups induced using oral largactil (G3), low dose fluphenazine (G4)
and high dose fluphenazine (G5). After 100 days, rats were subjected
to serum prolactin (PRL) level measurements and for basic seminal
fluid analysis (BSA). The difference between serum PRL
concentrations of rats in G2, G3, G4 and G5 as compared to the
control group were highly significant by Student’s t-test (p
Abstract: In the present work, detailed analysis on flow characteristics of a pair of immiscible liquids through horizontal pipeline is simulated by using ANSYS FLUENT 6.2. Moderately viscous oil and water (viscosity ratio = 107, density ratio = 0.89 and interfacial tension = 0.024 N/m) have been taken as system fluids for the study. Volume of Fluid (VOF) method has been employed by assuming unsteady flow, immiscible liquid pair, constant liquid properties, and co-axial flow. Meshing has been done using GAMBIT. Quadrilateral mesh type has been chosen to account for the surface tension effect more accurately. From the grid independent study, we have selected 47037 number of mesh elements for the entire geometry. Simulation successfully predicts slug, stratified wavy, stratified mixed and annular flow, except dispersion of oil in water, and dispersion of water in oil. Simulation results are validated with horizontal literature data and good conformity is observed. Subsequently, we have simulated the hydrodynamics (viz., velocity profile, area average pressure across a cross section and volume fraction profile along the radius) of stratified wavy and annular flow at different phase velocities. The simulation results show that in the annular flow, total pressure of the mixture decreases with increase in oil velocity due to the fact that pipe cross section is completely wetted with water. Simulated oil volume fraction shows maximum at the centre in core annular flow, whereas, in stratified flow, maximum value appears at upper side of the pipeline. These results are in accord with the actual flow configuration. Our findings could be useful in designing pipeline for transportation of crude oil.
Abstract: Fluid rheology may have essential impact on sound propagation in a liquid-filled pipe, especially, in a low frequency range. Rheological parameters of liquid are temperature-sensitive, which ultimately results in a temperature dependence of the wave speed and attenuation in the waveguide. The study is devoted to modeling of this effect at sound propagation in an elastic pipe with polymeric liquid, described by generalized Maxwell model with non-zero high-frequency viscosity. It is assumed that relaxation spectrum is distributed according to the Spriggs law; temperature impact on the liquid rheology is described on the basis of the temperature-superposition principle and activation theory. The dispersion equation for the waveguide, considered as a thin-walled tube with polymeric solution, is obtained within a quasi-one-dimensional formulation. Results of the study illustrate the influence of temperature on sound propagation in the system.
Abstract: Turbulent flow in complex geometries receives considerable attention due to its importance in many engineering applications. It has been the subject of interest for many researchers. Some of these interests include the design of storm water channels. The design of these channels requires testing through physical models. The main practical limitation of physical models is the so called “scale effect”, that is, the fact that in many cases only primary physical mechanisms can be correctly represented, while secondary mechanisms are often distorted. These observations form the basis of our study, which centered on problems associated with the design of storm water channels near the Dead Sea, in Israel. To help reach a final design decision we used different physical models. Our research showed good coincidence with the results of laboratory tests and theoretical calculations, and allowed us to study different effects of fluid flow in an open channel. We determined that problems of this nature cannot be solved only by means of theoretical calculation and computer simulation. This study demonstrates the use of physical models to help resolve very complicated problems of fluid flow through baffles and similar structures. The study applies these models and observations to different construction and multiphase water flows, among them, those that include sand and stone particles, a significant attempt to bring to the testing laboratory a closer association with reality.
Abstract: This study presents the numerical simulation of three-dimensional incompressible steady and laminar fluid flow and conjugate heat transfer of a trapezoidal microchannel heat sink using water as a cooling fluid in a silicon substrate. Navier-Stokes equations with conjugate energy equation are discretized by finite-volume method. We perform numerical computations for a range of 50 ≦ Re ≦ 600, 0.05W ≦ P ≦ 0.8W, 20W/cm2 ≦q"≦ 40W/cm2. The present study demonstrates the numerical optimization of a trapezoidal microchannel heat sink design using the response surface methodology (RSM) and the genetic algorithm method (GA). The results show that the average Nusselt number increases with an increase in the Reynolds number or pumping power, and the thermal resistance decreases as the pumping power increases. The thermal resistance of a trapezoidal microchannel is minimized for a constant heat flux and constant pumping power.
Abstract: This study applies the inverse method and three- dimensional CFD commercial software in conjunction with the experimental temperature data to investigate the heat transfer and fluid flow characteristics of the plate-fin heat sink in a closed rectangular enclosure for various values of fin height. The inverse method with the finite difference method and the experimental temperature data is applied to determine the heat transfer coefficient. The k-ε turbulence model is used to obtain the heat transfer and fluid flow characteristics within the fins. To validate the accuracy of the results obtained, the comparison of the average heat transfer coefficient is made. The calculated temperature at selected measurement locations on the plate-fin is also compared with experimental data.
Abstract: This paper investigates the natural convection heat transfer performance in a complex-wavy-wall cavity filled with power-law fluid. In performing the simulations, the continuity, Cauchy momentum and energy equations are solved subject to the Boussinesq approximation using a finite volume method. The simulations focus specifically on the effects of the flow behavior index in the power-law model and the Rayleigh number on the flow streamlines, isothermal contours and mean Nusselt number within the cavity. The results show that pseudoplastic fluids have a better heat transfer performance than Newtonian or dilatant fluids. Moreover, it is shown that for Rayleigh numbers greater than Ra=103, the mean Nusselt number has a significantly increase as the flow behavior index is decreased.
Abstract: This paper presents the findings from a numerical simulation of the flow in 37-rod fuel assembly models spaced by a double-wire trapezoidal wrapping as applied to the BREST-OD-300 experimental nuclear reactor. Data on a high static pressure distribution within the models, and equations for determining the fuel bundle flow friction factors have been obtained. Recommendations are provided on using the closing turbulence models available in the ANSYS Fluent. A comparative analysis has been performed against the existing empirical equations for determining the flow friction factors. The calculated and experimental data fit has been shown.
An analysis into the experimental data and results of the numerical simulation of the BREST-OD-300 fuel rod assembly hydrodynamic performance are presented.