Abstract: Three sulphonic acid-doped polyanilines were
synthesized through chemical oxidation at low temperature (0-5 oC)
and potential of these polymers as sensing agent for O2 gas detection
in terms of fluorescence quenching was studied. Sulphuric acid,
dodecylbenzene sulphonic acid (DBSA) and camphor sulphonic acid
(CSA) were used as doping agents. All polymers obtained were dark
green powder. Polymers obtained were characterized by Fourier
transform infrared spectroscopy, ultraviolet-visible absorption
spectroscopy, thermogravimetry analysis, elemental analysis,
differential scanning calorimeter and gel permeation
chromatography. Characterizations carried out showed that polymers
were successfully synthesized with mass recovery for sulphuric aciddoped
polyaniline (SPAN), DBSA-doped polyaniline (DBSA-doped
PANI) and CSA-doped polyaniline (CSA-doped PANI) of 71.40%,
75.00% and 39.96%, respectively. Doping level of SPAN, DBSAdoped
PANI and CSA-doped PANI were 32.86%, 33.13% and
53.96%, respectively as determined based on elemental analysis.
Sensing test was carried out on polymer sample in the form of
solution and film by using fluorescence spectrophotometer. Samples
of polymer solution and polymer film showed positive response
towards O2 exposure. All polymer solutions and films were fully
regenerated by using N2 gas within 1 hour period. Photostability
study showed that all samples of polymer solutions and films were
stable towards light when continuously exposed to xenon lamp for 9
hours. The relative standard deviation (RSD) values for SPAN
solution, DBSA-doped PANI solution and CSA-doped PANI
solution for repeatability were 0.23%, 0.64% and 0.76%,
respectively. Meanwhile RSD values for reproducibility were 2.36%,
6.98% and 1.27%, respectively. Results for SPAN film, DBSAdoped
PANI film and CSA-doped PANI film showed the same
pattern with RSD values for repeatability of 0.52%, 4.05% and
0.90%, respectively. Meanwhile RSD values for reproducibility were
2.91%, 10.05% and 7.42%, respectively. The study on effect of the
flow rate on response time was carried out using 3 different rates
which were 0.25 mL/s, 1.00 mL/s and 2.00 mL/s. Results obtained
showed that the higher the flow rate, the shorter the response time.
Abstract: Total liquid ventilation can support gas exchange in animal models of lung injury. Clinical application awaits further technical improvements and performance verification. Our aim was to develop a liquid ventilator, able to deliver accurate tidal volumes, and a computerized system for measuring lung mechanics. The computer-assisted, piston-driven respirator controlled ventilatory parameters that were displayed and modified on a real-time basis. Pressure and temperature transducers along with a lineal displacement controller provided the necessary signals to calculate lung mechanics. Ten newborn lambs (
Abstract: For smaller mechatronic device, especially for micro
Electronic system, a micro machining is a must. However, most
investigations on vibration of a mill have been limited to the
traditional type mill. In this article, vibration and dynamic
characteristics of a micro mill were investigated in this study. The
trend towards higher precision manufacturing technology requires
producing miniaturized components. To improve micro-milled
product quality, obtain a higher production rate and avoid milling
breakage, the dynamic characteristics of micro milling must be
studied. A stepped pre-twisted mill is used to simulate the micro mill.
The finite element analysis is employed in this work. The flute length
and diameter effects of the micro mill are considered. It is clear that
the effects of micro mill shape parameters on vibration in a micro mill
are significant.
Abstract: This work is focused on the steady boundary layer flow
near the forward stagnation point of plane and axisymmetric bodies
towards a stretching sheet. The no slip condition on the solid
boundary is replaced by the partial slip condition. The analytical
solutions for the velocity distributions are obtained for the various
values of the ratio of free stream velocity and stretching velocity, slip
parameter, the suction and injection velocity parameter, magnetic
parameter and dimensionality index parameter in the series forms with
the help of homotopy analysis method (HAM). Convergence of the
series is explicitly discussed. Results show that the flow and the skin
friction coefficient depend heavily on the velocity slip factor. In
addition, the effects of all the parameters mentioned above were more
pronounced for plane flows than for axisymmetric flows.
Abstract: The quantitative determination of several trace
elements (Cr, As, Se, Cd, Hg, Pb) existing as inorganic impurities in
some oriental herb-products such as Lingzhi Mushroom capsules,
Philamin powder, etc using ICP-MS has been studied. Various
instrumental parameters such as power, gas flow rate, sample depth, as
well as the concentration of nitric acid and thick background due to
high concentration of possible interferences on the determination of
these above-mentioned elements was investigated and the optimum
working conditions of the sample measurement on ICP-MS
(Agilent-7500a) were reported. Appropriate isotope internal standards
were also used to improve the accuracy of mercury determination.
Optimal parameters for sampling digestion were also investigated. The
recovery of analytical procedure was examined by using a Certified
Reference Material (IAEA-CRM 359). The recommended procedure
was then applied for the quantitative determination of Cr, As, Se, Cd,
Hg, Pb in Lingzhi Mushroom capsule, and Philamine powder samples.
The reproducibility of sample measurement (average value between
94 and 102%) and the uncertainty of analytical data (less than 20%)
are acceptable.
Abstract: End milling process is one of the common metal
cutting operations used for machining parts in manufacturing
industry. It is usually performed at the final stage in manufacturing a
product and surface roughness of the produced job plays an
important role. In general, the surface roughness affects wear
resistance, ductility, tensile, fatigue strength, etc., for machined parts
and cannot be neglected in design. In the present work an
experimental investigation of end milling of aluminium alloy with
carbide tool is carried out and the effect of different cutting
parameters on the response are studied with three-dimensional
surface plots. An artificial neural network (ANN) is used to establish
the relationship between the surface roughness and the input cutting
parameters (i.e., spindle speed, feed, and depth of cut). The Matlab
ANN toolbox works on feed forward back propagation algorithm is
used for modeling purpose. 3-12-1 network structure having
minimum average prediction error found as best network architecture
for predicting surface roughness value. The network predicts surface
roughness for unseen data and found that the result/prediction is
better. For desired surface finish of the component to be produced
there are many different combination of cutting parameters are
available. The optimum cutting parameter for obtaining desired
surface finish, to maximize tool life is predicted. The methodology is
demonstrated, number of problems are solved and algorithm is coded
in Matlab®.
Abstract: Static Var Compensator (SVC) is a shunt type FACTS
device which is used in power system primarily for the purpose of
voltage and reactive power control. In this paper, a fuzzy logic based
supplementary controller for Static Var Compensator (SVC) is
developed which is used for damping the rotor angle oscillations and
to improve the transient stability of the power system. Generator
speed and the electrical power are chosen as input signals for the
Fuzzy Logic Controller (FLC). The effectiveness and feasibility of
the proposed control is demonstrated with Single Machine Infinite
Bus (SMIB) system and multimachine system (WSCC System)
which show improvement over the use of a fixed parameter
controller.
Abstract: There are two types of drought as conceptual drought
and operational drought. The three parameters as the beginning, the
end and the degree of severity of the drought can be identifying in
operational drought by average precipitation in the whole region. One
of the methods classified to measure drought is Reconnaissance
Drought Index (RDI). Evapotranspiration is calculated using
Penman-Monteith method by analyzing thirty nine years prolong
climatic data. The evapotranspiration is then utilized in RDI to
classify normalized and standardized RDI. These RDI classifications
led to what kind of drought faced in Bhavnagar region on 12 month
time scale basis. The comparison between actual drought conditions
and RDI method used to find out drought are also illustrated. It can
be concluded that the index results of drought in a particular year are
same in both methods but having different index values where as
severity remain same.
Abstract: The security of power systems against malicious cyberphysical
data attacks becomes an important issue. The adversary
always attempts to manipulate the information structure of the power
system and inject malicious data to deviate state variables while
evading the existing detection techniques based on residual test. The
solutions proposed in the literature are capable of immunizing the
power system against false data injection but they might be too costly
and physically not practical in the expansive distribution network.
To this end, we define an algebraic condition for trustworthy power
system to evade malicious data injection. The proposed protection
scheme secures the power system by deterministically reconfiguring
the information structure and corresponding residual test. More
importantly, it does not require any physical effort in either microgrid
or network level. The identification scheme of finding meters being
attacked is proposed as well. Eventually, a well-known IEEE 30-bus
system is adopted to demonstrate the effectiveness of the proposed
schemes.
Abstract: A generalized method for small-signal simulation of
avalanche noise in Mixed Tunneling Avalanche Transit Time
(MITATT) device is presented in this paper where the effect of series
resistance is taken into account. The method is applied to a
millimeter-wave Double Drift Region (DDR) MITATT device based
on Silicon to obtain noise spectral density and noise measure as a
function of frequency for different values of series resistance. It is
found that noise measure of the device at the operating frequency
(122 GHz) with input power density of 1010 Watt/m2 is about 35 dB
for hypothetical parasitic series resistance of zero ohm (estimated
junction temperature = 500 K). Results show that the noise measure
increases as the value of parasitic resistance increases.
Abstract: In this study Vitaton (an organic supplement which
contains fermentative β-carotene) and synthetic astaxanthin
(CAROPHYLL® Pink) were evaluated as pro-growth factors in
Rainbow trout diet. An 8 week feeding trial was conducted to
determine the effects of Vitaton versus astaxanthin on rearing factors,
survival rate and visual flesh color of Rainbow trout
(Oncorhnchynchus mykiss) with initial weight of 196±5. Four
practical diets were formulated to contain 50 and 80 (ppm) of β-
carotene and astaxanthin and also a control diet was prepared without
any pigment. Each diet was fed to triplicate groups of fish rearing in
fresh water. Fish were fed twice daily. The water temperature
fluctuated from 12 to 15 (C˚) and also dissolved oxygen content was
between 7 to 7.5 (mg/lit) during the experimental period. At the end
of the experiment, growth and food utilization parameters and
survival rate were unaffected by dietary treatments (p>0.05). Also,
there was no significant difference between carcass yield within
treatments (p>0.05). No significant difference recognized between
visual flesh color (SalmoFan score) of fish fed Vitaton-containing
diets. On the contrary, feeding on diets containing 50 and 80 (ppm)
of astaxanthin, increased SalmoFan score (flesh astaxanthin
concentration) from
Abstract: Observations show that power plant efficiency
decreases in hot summer days. Water droplet injection in air
condensers is suggested in order to decrease the inlet air temperature.
Nozzle arrangement, injected water flow rate and droplets diameter
effects on evaporation rate and the resulting air temperature are
investigated using numerical simulation. Decreasing the diameter of
injected droplets and increasing the number of injecting nozzles,
decreases the outlet air temperature. Also a more uniform air
temperature can be obtained using more injecting nozzles. Numerical
results are in good agreement with analytical results.
Abstract: An additive fuzzy system comprising m rules with
n inputs and p outputs in each rule has at least t m(2n + 2 p + 1)
parameters needing to be tuned. The system consists of a large
number of if-then fuzzy rules and takes a long time to tune its
parameters especially in the case of a large amount of training data
samples. In this paper, a new learning strategy is investigated to cope
with this obstacle. Parameters that tend toward constant values at the
learning process are initially fixed and they are not tuned till the end
of the learning time. Experiments based on applications of the
additive fuzzy system in function approximation demonstrate that the
proposed approach reduces the learning time and hence improves
convergence speed considerably.
Abstract: The fuel cost of the motor vehicle operating on its
common route is an important part of the operating cost. Therefore,
the importance of the fuel saving is increasing day by day. One of the
parameters which improve fuel saving is the regulation of driving
characteristics. The number and duration of stop is increased by the
heavy traffic load. It is possible to improve the fuel saving with
regulation of traffic flow and driving characteristics. The researches
show that the regulation of the traffic flow decreases fuel
consumption, but it is not enough to improve fuel saving without the
regulation of driving characteristics. This study analyses the fuel
consumption of two trips of city bus operating on its common route
and determines the effect of traffic density and driving characteristics
on fuel consumption. Finally it offers some suggestions about
regulation of driving characteristics to improve the fuel saving. Fuel
saving is determined according to the results obtained from
simulation program. When experimental and simulation results are
compared, it has been found that the fuel saving was reached up the
to 40 percent ratios.
Abstract: Gold coated silica core nanoparticles have an optical
response dictated by the plasmon resonance. The wavelength at
which the resonance occurs depends on the core and shell sizes,
allowing nanoshells to be tailored for particular applications. The
purposes of this study was to synthesize and use different
concentration of gold nanoshells as exogenous material for skin
tissue soldering and also to examine the effect of laser soldering
parameters on the properties of repaired skin. Two mixtures of
albumin solder and different concentration of gold nanoshells were
prepared. A full thickness incision of 2×20 mm2 was made on the
surface and after addition of mixtures it was irradiated by an 810nm
diode laser at different power densities. The changes of tensile
strength σt due to temperature rise, number of scan (Ns), and scan
velocity (Vs) were investigated. The results showed at constant laser
power density (I), σt of repaired incisions increases by increasing the
concentration of gold nanoshells, Ns and decreasing Vs. It is therefore
important to consider the trade off between the scan velocity and the
surface temperature for achieving an optimum operating condition. In
our case this corresponds to σt =1610 gr/cm2 at I~ 60 Wcm-2, T ~
65ºC, Ns =10 and Vs=0.2mms-1.
Abstract: This paper presents a methodology to harvest the kinetic energy of the raindrops using piezoelectric devices. In the study 1m×1m PVDF (Polyvinylidene fluoride) piezoelectric membrane, which is fixed by the four edges, is considered for the numerical simulation on deformation of the membrane due to the impact of the raindrops. Then according to the drop size of the rain, the simulation is performed classifying the rainfall types into three categories as light stratiform rain, moderate stratiform rain and heavy thundershower. The impact force of the raindrop is dependent on the terminal velocity of the raindrop, which is a function of raindrop diameter. The results were then analyzed to calculate the harvestable energy from the deformation of the piezoelectric membrane.
Abstract: In this study, control performance of a smart base
isolation system consisting of a friction pendulum system (FPS) and a
magnetorheological (MR) damper has been investigated. A fuzzy
logic controller (FLC) is used to modulate the MR damper so as to
minimize structural acceleration while maintaining acceptable base
displacement levels. To this end, a multi-objective optimization
scheme is used to optimize parameters of membership functions and
find appropriate fuzzy rules. To demonstrate effectiveness of the
proposed multi-objective genetic algorithm for FLC, a numerical
study of a smart base isolation system is conducted using several
historical earthquakes. It is shown that the proposed method can find
optimal fuzzy rules and that the optimized FLC outperforms not only a
passive control strategy but also a human-designed FLC and a
conventional semi-active control algorithm.
Abstract: Plants are commonly known for its positive
correlation in reducing temperature. Since it can benefit buildings by
modifying the microclimate, it-s also believed capable of reducing
the internal temperature. Various experiments have been done in
Universiti Sains Malaysia, Penang to investigate the comparison in
thermal benefits between two rooms, one being a typical control
room (exposed wall) and the other a biofacade room (plant shaded
wall). The investigations were conducted during non-rainy season for
approximately a month. Climbing plant Psophocarpus
tetrogonobulus from legume species was selected as insulation for
the biofacade wall. Conclusions were made on whether the biofacade
can be used to tackle the energy efficiency, based on the parameters
taken into consideration.
Abstract: This paper presents a hybrid approach for solving nqueen problem by combination of PSO and SA. PSO is a population based heuristic method that sometimes traps in local maximum. To solve this problem we can use SA. Although SA suffer from many iterations and long time convergence for solving some problems, By good adjusting initial parameters such as temperature and the length of temperature stages SA guarantees convergence. In this article we use discrete PSO (due to nature of n-queen problem) to achieve a good local maximum. Then we use SA to escape from local maximum. The experimental results show that our hybrid method in comparison of SA method converges to result faster, especially for high dimensions n-queen problems.