Abstract: Three new algorithms based on minimization of autocorrelation of transmitted symbols and the SLM approach which are computationally less demanding have been proposed. In the first algorithm, autocorrelation of complex data sequence is minimized to a value of 1 that results in reduction of PAPR. Second algorithm generates multiple random sequences from the sequence generated in the first algorithm with same value of autocorrelation i.e. 1. Out of these, the sequence with minimum PAPR is transmitted. Third algorithm is an extension of the second algorithm and requires minimum side information to be transmitted. Multiple sequences are generated by modifying a fixed number of complex numbers in an OFDM data sequence using only one factor. The multiple sequences represent the same data sequence and the one giving minimum PAPR is transmitted. Simulation results for a 256 subcarrier OFDM system show that significant reduction in PAPR is achieved using the proposed algorithms.
Abstract: This paper will focus on modeling, analysis and simulation of a 42V/14V dc/dc converter based architecture. This architecture is considered to be technically a viable solution for automotive dual-voltage power system for passenger car in the near further. An interleaved dc/dc converter system is chosen for the automotive converter topology due to its advantages regarding filter reduction, dynamic response, and power management. Presented herein, is a model based on one kilowatt interleaved six-phase buck converter designed to operate in a Discontinuous Conduction Mode (DCM). The control strategy of the converter is based on a voltagemode- controlled Pulse Width Modulation (PWM) with a Proportional-Integral-Derivative (PID). The effectiveness of the interleaved step-down converter is verified through simulation results using control-oriented simulator, MatLab/Simulink.
Abstract: The behavior of three phase five leg transformer under voltage sag is studied in this paper. This paper proposes a simple, practical model of a three phase-five leg, saturated transformer with accurate performance. Transformer saturation is produced when the voltage sag is recovered and it causes inrush current in transformer. Effects of voltage sag depth, duration and initial point on wave have been analyzed in this paper. Initial point on wave can produce maximum inrush current in five leg transformers while comparing with three leg transformers. The magnetic circuit symmetry of five leg transformer produces the more symmetrical shape of inrush current curves versus initial point on wave and sag duration than three leg transformer. The simulations show that current peak has a periodical dependence on sag duration and linear dependence on sag depth. Inrush current that is produced in three phase five leg transformer is higher than three phase three leg transformer.
Abstract: Time series analysis often requires data that represents
the evolution of an observed variable in equidistant time steps. In
order to collect this data sampling is applied. While continuous
signals may be sampled, analyzed and reconstructed applying
Shannon-s sampling theorem, time-discrete signals have to be dealt
with differently. In this article we consider the discrete-event
simulation (DES) of job-shop-systems and study the effects of
different sampling rates on data quality regarding completeness and
accuracy of reconstructed inventory evolutions. At this we discuss
deterministic as well as non-deterministic behavior of system
variables. Error curves are deployed to illustrate and discuss the
sampling rate-s impact and to derive recommendations for its wellfounded
choice.
Abstract: Recently, there have been considerable efforts towards the convergence between P2P and Grid computing in order to reach a solution that takes the best of both worlds by exploiting the advantages that each offers. Augmenting the peer-to-peer model to the services of the Grid promises to eliminate bottlenecks and ensure greater scalability, availability, and fault-tolerance. The Grid Information Service (GIS) directly influences quality of service for grid platforms. Most of the proposed solutions for decentralizing the GIS are based on completely flat overlays. The main contributions for this paper are: the investigation of a novel resource discovery framework for Grid implementations based on a hierarchy of structured peer-to-peer overlay networks, and introducing a discovery algorithm utilizing the proposed framework. Validation of the framework-s performance is done via simulation. Experimental results show that the proposed organization has the advantage of being scalable while providing fault-isolation, effective bandwidth utilization, and hierarchical access control. In addition, it will lead to a reliable, guaranteed sub-linear search which returns results within a bounded interval of time and with a smaller amount of generated traffic within each domain.
Abstract: This paper presents a CFD analysis of the flow around
a 30° inclined flat plate of infinite span. Numerical predictions have
been compared to experimental measurements, in order to assess the
potential of the finite volume code of determining the aerodynamic
forces acting on a flat plate invested by a fluid stream of infinite
extent.
Several turbulence models and spatial node distributions have
been tested and flow field characteristics in the neighborhood of the
flat plate have been numerically investigated, allowing the
development of a preliminary procedure to be used as guidance in
selecting the appropriate grid configuration and the corresponding
turbulence model for the prediction of the flow field over a twodimensional
inclined plate.
Abstract: Active Power Filters (APFs) are today the most
widely used systems to eliminate harmonics compensate power
factor and correct unbalanced problems in industrial power plants.
We propose to improve the performances of conventional APFs by
using artificial neural networks (ANNs) for harmonics estimation.
This new method combines both the strategies for extracting the
three-phase reference currents for active power filters and DC link
voltage control method. The ANNs learning capabilities to
adaptively choose the power system parameters for both to compute
the reference currents and to recharge the capacitor value requested
by VDC voltage in order to ensure suitable transit of powers to
supply the inverter. To investigate the performance of this
identification method, the study has been accomplished using
simulation with the MATLAB Simulink Power System Toolbox. The
simulation study results of the new (SAPF) identification technique
compared to other similar methods are found quite satisfactory by
assuring good filtering characteristics and high system stability.
Abstract: A subjectively influenced router for vehicles in a fourjunction
traffic system is presented. The router is based on a 3-layer
Backpropagation Neural Network (BPNN) and a greedy routing
procedure. The BPNN detects priorities of vehicles based on the
subjective criteria. The subjective criteria and the routing procedure
depend on the routing plan towards vehicles depending on the user.
The routing procedure selects vehicles from their junctions based on
their priorities and route them concurrently to the traffic system. That
is, when the router is provided with a desired vehicles selection
criteria and routing procedure, it routes vehicles with a reasonable
junction clearing time. The cost evaluation of the router determines
its efficiency. In the case of a routing conflict, the router will route
the vehicles in a consecutive order and quarantine faulty vehicles.
The simulations presented indicate that the presented approach is an
effective strategy of structuring a subjective vehicle router.
Abstract: The paper proposes a new concept in developing
collaborative design system. The concept framework involves
applying simulation of supply chain management to collaborative
design called – 'SCM–Based Design Tool'. The system is developed
particularly to support design activities and to integrate all facilities
together. The system is aimed to increase design productivity and
creativity. Therefore, designers and customers can collaborate by the
system since conceptual design. JAG: Jewelry Art Generator based
on artificial intelligence techniques is integrated into the system.
Moreover, the proposed system can support users as decision tool
and data propagation. The system covers since raw material supply
until product delivery. Data management and sharing information are
visually supported to designers and customers via user interface. The
system is developed on Web–assisted product development
environment. The prototype system is presented for Thai jewelry
industry as a system prototype demonstration, but applicable for
other industry.
Abstract: In MPEG and H.26x standards, to eliminate the
temporal redundancy we use motion estimation. Given that the
motion estimation stage is very complex in terms of computational
effort, a hardware implementation on a re-configurable circuit is
crucial for the requirements of different real time multimedia
applications. In this paper, we present hardware architecture for
motion estimation based on "Full Search Block Matching" (FSBM)
algorithm. This architecture presents minimum latency, maximum
throughput, full utilization of hardware resources such as embedded
memory blocks, and combining both pipelining and parallel
processing techniques. Our design is described in VHDL language,
verified by simulation and implemented in a Stratix II
EP2S130F1020C4 FPGA circuit. The experiment result show that the
optimum operating clock frequency of the proposed design is 89MHz
which achieves 160M pixels/sec.
Abstract: techniques are examined to overcome the
performance degradation caused by the channel dispersion using
slow frequency hopping (SFH) with dynamic frequency hopping
(DFH) pattern adaptation. In DFH systems, the frequency slots are
selected by continuous quality monitoring of all frequencies available
in a system and modification of hopping patterns for each individual
link based on replacing slots which its signal to interference ratio
(SIR) measurement is below a required threshold. Simulation results
will show the improvements in BER obtained by DFH in comparison
with matched frequency hopping (MFH), random frequency hopping
(RFH) and multi-carrier code division multiple access (MC-CDMA)
in multipath slowly fading dispersive channels using a generalized
bandpass two-path transfer function model, and will show the
improvement obtained according to the threshold selection.
Abstract: In this work, we used the single Langmuir probe to
measure the plasma density distribution in an geometrically
asymmetric capacitive coupled plasma discharge system. Because of
the frame structure of powered electrode, the plasma density was not
homogeneous in the discharge volume. It was higher under the frame,
but lower in the centre. Finite element simulation results showed a
good agreement with the experiment results. To increase the electron
density in the central volume and improve the homogeneity of the
plasma, we added an auxiliary electrode, powered by DC voltage, in
the simulation geometry. The simulation results showed that the
auxiliary electrode could alter the potential distribution and improve
the density homogeneity effectively.
Abstract: This paper proposes a vehicle-to-vehicle propagation
model implemented with SDL. To estimate the channel
characteristics for Inter-Vehicle communication, we first define a
predicted propagation pathloss between the moving vehicles under
three typical scenarios. A Ray-tracing method is used for the simple
gamma model performance.
Abstract: Today, transport and logistic systems are often tightly
integrated in the production. Lean production and just-in-time delivering create multiple constraints that have to be fulfilled. As transport networks often have evolved over time they are very
expensive to change. This paper describes a discrete-event-simulation
system which simulates transportation models using real time
resource routing and collision avoidance. It allows for the
specification of own control algorithms and validation of new
strategies. The simulation is integrated into a virtual reality (VR)
environment and can be displayed in 3-D to show the progress.
Simulation elements can be selected through VR metaphors. All data
gathered during the simulation can be presented as a detailed summary afterwards. The included cost-benefit calculation can help to optimize the financial outcome. The operation of this approach is shown by the example of a timber harvest simulation.
Abstract: This paper presents a novel control method based on radial basis function networks (RBFNs) for chaotic dynamical systems. The proposed method first identifies the nonlinear part of the chaotic system off-line and then constructs a model-following controller using only the estimated system parameters. Simulation results show the effectiveness of the proposed control scheme.
Abstract: Presents a concept for a multidisciplinary process
supporting effective task transitions between different technical
domains during the architectural design stage.
A system configuration challenge is the multifunctional driven
increased solution space. As a consequence, more iteration is needed
to find a global optimum, i.e. a compromise between involved
disciplines without negative impact on development time. Since state
of the art standards like ISO 15288 and VDI 2206 do not provide a
detailed methodology on multidisciplinary design process, higher
uncertainties regarding final specifications arise. This leads to the
need of more detailed and standardized concepts or processes which
could mitigate risks.
The performed work is based on analysis of multidisciplinary
interaction, of modeling and simulation techniques. To demonstrate
and prove the applicability of the presented concept, it is applied to
the design of aircraft high lift systems, in the context of the
engineering disciplines kinematics, actuation, monitoring, installation
and structure design.
Abstract: With high speed vessels getting ever more sophisti-cated, travelling at higher and higher speeds and operating in With high speed vessels getting ever more sophisticated,
travelling at higher and higher speeds and operating in areas of
high maritime traffic density, training becomes of the highest priority
to ensure that safety levels are maintained, and risks are adequately
mitigated. Training onboard the actual craft on the actual route still
remains the most effective way for crews to gain experience. However,
operational experience and incidents during the last 10 years
demonstrate the need for supplementary training whether in the area
of simulation or man to man, man/ machine interaction. Training and
familiarisation of the crew is the most important aspect in preventing
incidents. The use of simulator, computer and web based training
systems in conjunction with onboard training focusing on critical
situations will improve the man machine interaction and thereby
reduce the risk of accidents. Today, both ship simulator and bridge
teamwork courses are now becoming the norm in order to improve
further emergency response and crisis management skills. One of the
main causes of accidents is the human factor. An efficient way to
reduce human errors is to provide high-quality training to the personnel
and to select the navigators carefully.areas of high maritime traffic density, training becomes of the highest priority to ensure that safety levels are maintained, and risks are adequately mitigated. Training onboard the actual craft on the actual route still remains the most effective way for crews to gain experience. How-ever, operational experience and incidents during the last 10 years demonstrate the need for supplementary training whether in the area of simulation or man to man, man/ machine interaction. Training and familiarisation of the crew is the most important aspect in preventing incidents. The use of simulator, computer and web based training systems in conjunction with onboard training focusing on critical situations will improve the man machine interaction and thereby reduce the risk of accidents. Today, both ship simulator and bridge teamwork courses are now becoming the norm in order to improve further emergency response and crisis management skills. One of the main causes of accidents is the human factor. An efficient way to reduce human errors is to provide high-quality training to the person-nel and to select the navigators carefully. KeywordsCBT - WBT systems, Human factors.
Abstract: This paper addresses parameter and state estimation problem in the presence of the perturbation of observer gain bounded input disturbances for the Lipschitz systems that are linear in unknown parameters and nonlinear in states. A new nonlinear adaptive resilient observer is designed, and its stability conditions based on Lyapunov technique are derived. The gain for this observer is derived systematically using linear matrix inequality approach. A numerical example is provided in which the nonlinear terms depend on unmeasured states. The simulation results are presented to show the effectiveness of the proposed method.
Abstract: In this work, a Modified Functional Link Artificial
Neural Network (M-FLANN) is proposed which is simpler than a
Multilayer Perceptron (MLP) and improves upon the universal
approximation capability of Functional Link Artificial Neural
Network (FLANN). MLP and its variants: Direct Linear Feedthrough
Artificial Neural Network (DLFANN), FLANN and
M-FLANN have been implemented to model a simulated Water Bath
System and a Continually Stirred Tank Heater (CSTH). Their
convergence speed and generalization ability have been compared.
The networks have been tested for their interpolation and
extrapolation capability using noise-free and noisy data. The results
show that M-FLANN which is computationally cheap, performs
better and has greater generalization ability than other networks
considered in the work.
Abstract: The finite-difference time-domain (FDTD) method is
one of the most widely used computational methods in
electromagnetic. This paper describes the design of two-dimensional
(2D) FDTD simulation software for transverse magnetic (TM)
polarization using Berenger's split-field perfectly matched layer
(PML) formulation. The software is developed using Matlab
programming language. Numerical examples validate the software.