Abstract: In this paper a computer system for electromagnetic
properties measurements is designed. The system employs Agilent
4294A precision impedance analyzer to measure the amplitude and
the phase of a signal applied over a tested biological tissue sample.
Measured by the developed computer system data could be used for
tissue characterization in wide frequency range from 40Hz to
110MHz. The computer system can interface with output devices
acquiring flexible testing process.
Abstract: Sixteen selected deep-sea fish obtained from Southern
Java Ocean and Western Sumatra Ocean was analyzed to determine
its proximate, fatty acid and mineral composition. The moisture
content was ranged from 64.38 to 86.04 %, ash from 0.17 to 0.69 %,
the fat content was 1.54 – 13.30 % while the protein content varied
from 15.84 to 23.60%. Among the fatty acids, oleic acid and palmitic
acid was the dominant MUFA and SFA. Linoleic acid was the
highest PUFA found at the selected deep-sea fish. Phospor was the
highest macroelement concentration on selected deep-sea fish,
followed by K, Ca, Mg and Iod, Fe and Zn among microelement. The
trace concentration was found at Se microelement.
Abstract: Use of microemulsion in enhanced oil recovery has become more attractive in recent years because of its high level of extraction efficiency. Experimental investigations have been made on characterization of microemulsions of oil-brinesurfactant/ cosurfactant system for its use in enhanced oil recovery (EOR). Sodium dodecyl sulfate, propan-1-ol and heptane were selected as surfactant, cosurfactant and oil respectively for preparation of microemulsion. The effects of salinity on the relative phase volumes and solubilization parameters have also been studied. As salinity changes from low to high value, phase transition takes place from Winsor I to Winsor II via Winsor III. Suitable microemulsion composition has been selected based on its stability and ability to reduce interfacial tension. A series of flooding experiments have been performed using the selected microemulsion. The flooding experiments were performed in a core flooding apparatus using uniform sand pack. The core holder was tightly packed with uniform sands (60-100 mesh) and saturated with brines of different salinities. It was flooded with the brine at 25 psig and the absolute permeability was calculated from the flow rate of the through sand pack. The sand pack was then flooded with the crude oil at 800 psig to irreducible water saturation. The initial water saturation was determined on the basis of mass balance. Waterflooding was conducted by placing the coreholder horizontally at a constant injection pressure at 200 pisg. After water flooding, when water-cut reached above 95%, around 0.5 pore volume (PV) of the above microemulsion slug was injected followed by chasing water. The experiments were repeated using different composition of microemulsion slug. The additional recoveries were calculated by material balance. Encouraging results with additional recovery more than 20% of original oil in place above the conventional water flooding have been observed.
Abstract: Deflocculation and gel characterization were
investigated for three different composition of porcelain slips at
specific gravity 1.8. The suspensions were dispersed with sodium
silicate (Na2SiO3) in under-deflocculated slips and fully deflocculated
slips. The rheology characterization of slips was conducted by the
deflocculation curves and the gel curves. The results showed that
decreasing the amount of the ball clay composition in the slips
consumed less dosages of the dispersants. The under-deflocculated
slips tended to have a gelation rate faster than the fully deflocculated
slips.
Abstract: The growing health hazardous impact of arsenic (As)
contamination in environment is the impetus of the present
investigation. Application of lactic acid bacteria (LAB) for the
removal of toxic and heavy metals from water has been reported.
This study was performed in order to isolate and characterize the Asresistant
LAB from mud and sludge samples for using as efficient As
uptaking probiotic. Isolation of As-resistant LAB colonies was
performed by spread plate technique using bromocresol purple
impregnated-MRS (BP-MRS) agar media provided with As @ 50
μg/ml. Isolated LAB were employed for probiotic characterization
process, acid and bile tolerance, lactic acid production, antibacterial
activity and antibiotic tolerance assays. After As-resistant and
removal characterizations, the LAB were identified using 16S rDNA
sequencing. A total of 103 isolates were identified as As-resistant
strains of LAB. The survival of 6 strains (As99-1, As100-2, As101-3,
As102-4, As105-7, and As112-9) was found after passing through the
sequential probiotic characterizations. Resistant pattern pronounced
hollow zones at As concentration >2000 μg/ml in As99-1, As100-2,
and As101-3 LAB strains, whereas it was found at ~1000 μg/ml in
rest 3 strains. Among 6 strains, the As uptake efficiency of As102-4
(0.006 μg/h/mg wet weight of cell) was higher (17 – 209%)
compared to remaining LAB. 16S rDNA sequencing data of 3 (As99-
1, As100-2, and As101-3) and 3 (As102-4, As105-7, and As112-9)
LAB strains clearly showed 97 to 99% (340 bp) homology to
Pediococcus dextrinicus and Pediococcus acidilactici, respectively.
Though, there was no correlation between the metal resistant and
removal efficiency of LAB examined but identified elevated As
removing LAB would probably be a potential As uptaking probiotic
agent. Since present experiment concerned with only As removal
from pure water, As removal and removal mechanism in natural
condition of intestinal milieu should be assessed in future studies.
Abstract: Methods of contemporary mathematical physics such
as chaos theory are useful for analyzing and understanding the
behavior of complex biological and physiological systems. The three
dimensional model of HIV/AIDS is the basis of active research since
it provides a complete characterization of disease dynamics and the
interaction of HIV-1 with the immune system. In this work, the
behavior of the HIV system is analyzed using the three dimensional
HIV model and a chaotic measure known as the Hurst exponent.
Results demonstrate that Hurst exponents of CD4, CD8 cells and
viral load vary nonlinearly with respect to variations in system
parameters. Further, it was observed that the three dimensional HIV
model can accommodate both persistent (H>0.5) and anti-persistent
(H
Abstract: Polymer-like organic thin films were deposited on both
aluminum alloy type 6061 and glass substrates at room temperature by
Plasma Enhanced Chemical Vapor Deposition (PECVD) methodusing
benzene and hexamethyldisiloxane (HMDSO) as precursor materials.
The surface and physical properties of plasma-polymerized organic
thin films were investigated at different r.f. powers. The effects of
benzene/argon ratio on the properties of plasma polymerized benzene
films were also investigated. It is found that using benzene alone
results in a non-coherent and non-adherent powdery deposited
material. The chemical structure and surface properties of the asgrown
plasma polymerized thin films were analyzed on glass
substrates with FTIR and contact angle measurements. FTIR spectra
of benzene deposited film indicated that the benzene rings are
preserved when increasing benzene ratio and/or decreasing r.f.
powers. FTIR spectra of HMDSO deposited films indicated an
increase of the hydrogen concentration and a decrease of the oxygen
concentration with the increase of r.f. power. The contact angle (θ) of
the films prepared from benzene was found to increase by about 43%
as benzene ratio increases from 10% to 20%. θ was then found to
decrease to the original value (51°) when the benzene ratio increases
to 100%. The contact angle, θ, for both benzene and HMDSO
deposited films were found to increase with r.f. power. This signifies
that the plasma polymerized organic films have substantially low
surface energy as the r.f power increases. The corrosion resistance of
aluminum alloy substrate both bare and covered with plasma
polymerized thin films was carried out by potentiodynamic
polarization measurements in standard 3.5 wt. % NaCl solution at
room temperature. The results indicate that the benzene and HMDSO
deposited films are suitable for protection of the aluminum substrate
against corrosion. The changes in the processing parameters seem to
have a strong influence on the film protective ability. Surface
roughness of films deposited on aluminum alloy substrate was
investigated using scanning electron microscopy (SEM). The SEM
images indicate that the surface roughness of benzene deposited films
increase with decreasing the benzene ratio. SEM images of benzene
and HMDSO deposited films indicate that the surface roughness
decreases with increasing r.f. power. Studying the above parameters
indicate that the films produced are suitable for specific practical
applications.
Abstract: The carbon based coils with the nanometer scale have
the 3 dimension helix geometry. We synthesized the carbon nano-coils
by the use of chemical vapor deposition technique with iron and tin as
the catalysts. The fabricated coils have the external diameter of
ranging few hundred nm to few thousand nm. The Scanning
Electro-Microscope (SEM) and Tunneling Electro-Microscope has
shown detail images of the coil-s structure. The fabrication of the
carbon nano-coils can be grown on the metal and non-metal substrates,
such as the stainless steel and silicon substrates. Besides growth on the
flat substrate; they also can be grown on the stainless steel wires. After
the synthesis of the coils, the mechanical and electro-mechanical
property is measured. The experimental results were reported.
Abstract: Novel polystrene-bound Schiff bases and their Pt(IV)
complexes have been prepared from condensation reaction of
polystyrene-A-NH2 with 2-hydroxybenzaldehyde and 5-fluoro-3-
bromo-2-hydroxybenzaldehyde. The structures of Pt(IV) complexes
with polystyrene including Schiff bases have been determined by
elemental analyses, magnetic susceptibility, IR, 1H-NMR, UV-vis,
TG/DTA and AAS. The antibacterial and antifungal activities of the
synthesized compounds have been studied by the well-diffusion
method against some selected microorganisms: (Bacillus cereus spp.,
Listeria monocytogenes 4b, Micrococcus luteus, Staphylococcus
aureus, Staphylococcus epidermis, Brucella abortus, Escherichia
coli, Pseudomonas putida spp., Shigella dysenteria type 10,
Salmonella typhi H).
Abstract: The objective this study was to characterize and
develop anthropomorphic liver phantoms in tomography hepatic
procedures for quality control and improvement professionals in
nuclear medicine. For the conformation of the anthropomorphic
phantom was used in plaster and acrylic. We constructed three
phantoms representing processes with liver cirrhosis. The phantoms
were filled with 99mTc diluted with water to obtain the scintigraphic
images. Tomography images were analyzed anterior and posterior
phantom representing a body with a greater degree cirrhotic. It was
noted that the phantoms allow the acquisition of images similar to
real liver with cirrhosis. Simulations of hemangiomas may contribute
to continued professional education of nuclear medicine, on the
question of image acquisition, allowing of the study parameters such
of the matrix, energy window and count statistics.
Abstract: Physiological activity of the pineal gland with specific
responses in the reproductive territory may be interpreted by
monitoring the process parameters used in poultry practice in
different age batches of laying hens. As biological material were
used 105 laying hens, clinically healthy, belonging to ALBO SL-
2000 hybrid, raised on ground, from which blood samples were taken
at the age of 12 and 28 weeks. The haematological examinations
were concerned to obtain the total number of erythrocytes and
leukocytes and the main erythrocyte constant (RBC, PCV, MCV,
MCH, MCHC and WBC). The results allow the interpretation of the
reproductive status through the dynamics of the presented values.
Abstract: Nylon 6-clay hybrid/neat nylon 6, sheath/core
bicomponent nanocomposite fibers containing 4 wt% of clay in
sheath section were melt spun at different take-up speeds. Their
orientation and crystalline structure were compared to those of neat
nylon 6 fibers. Birefringence measurements showed that the
orientation development in sheath and core parts of bicomponent
fibers was different. Crystallinity results showed that clay did not act
as a nucleating agent for bicomponent fibers. The neat nylon 6 fiber
had a smooth surface while striped pattern was appeared on the
surface of bicomponent fiber containing clay due to thermal
shrinkage of the core part.
Abstract: In this paper, we define distance partition of vertex set of a graph G with reference to a vertex in it and with the help of the same, a graph with metric dimension two (i.e. β (G) = 2 ) is characterized. In the process, we develop a polynomial time algorithm that verifies if the metric dimension of a given graph G is two. The same algorithm explores all metric bases of graph G whenever β (G) = 2 . We also find a bound for cardinality of any distance partite set with reference to a given vertex, when ever β (G) = 2 . Also, in a graph G with β (G) = 2 , a bound for cardinality of any distance partite set as well as a bound for number of vertices in any sub graph H of G is obtained in terms of diam H .
Abstract: In this work, a characterization and modeling of
packet loss of a Voice over Internet Protocol (VoIP) communication
is developed. The distributions of the number of consecutive received
and lost packets (namely gap and burst) are modeled from the
transition probabilities of two-state and four-state model.
Measurements show that both models describe adequately the burst
distribution, but the decay of gap distribution for non-homogeneous
losses is better fit by the four-state model. The respective
probabilities of transition between states for each model were
estimated with a proposed algorithm from a set of monitored VoIP
calls in order to obtain representative minimum, maximum and
average values for both models.
Abstract: In this study, structural, mechanical, thermal and
electrical properties of poly (lactic acid) (PLA) nanocomposites with
low-loaded (0-1.5 wt%) untreated, heat and nitric acid treated multiwalled
carbon nanotubes (MWCNTs) were studied. Among the
composites, untreated 0.5 wt % MWCNTs and acid-treated 1.0 wt%
MWCNTs reinforced PLA show the tensile strength and modulus
values higher than the others. These two samples along with pure
PLA exhibit the stable orthorhombic α-form, whilst other samples
reveal the less stable orthorhombic β-form, as demonstrated by X-ray
diffraction study. Differential scanning calorimetry reveals the
evolution of the mentioned different phases by controlled cooling and
discloses an enhancement of PLA crystallization by nanotubes
incorporation. Thermogravimetric analysis shows that the MWCNTs
loaded sample degraded faster than PLA. Surface resistivity of the
nanocomposites is found to be dropped drastically by a factor of 1013
with a low loading of MWCNTs (1.5 wt%).
Abstract: In this study three commercial semiconductor devices
were characterized in the laboratory for computed tomography
dosimetry: one photodiode and two phototransistors. It was evaluated
four responses to the irradiation: dose linearity, energy dependence,
angular dependence and loss of sensitivity after X ray exposure. The
results showed that the three devices have proportional response with
the air kerma; the energy dependence displayed for each device
suggests that some calibration factors would be applied for each one;
the angular dependence showed a similar pattern among the three
electronic components. In respect to the fourth parameter analyzed,
one phototransistor has the highest sensitivity however it also showed
the greatest loss of sensitivity with the accumulated dose. The
photodiode was the device with the smaller sensitivity to radiation,
on the other hand, the loss of sensitivity after irradiation is negligible.
Since high accuracy is a desired feature for a dosimeter, the
photodiode can be the most suitable of the three devices for
dosimetry in tomography. The phototransistors can also be used for
CT dosimetry, however it would be necessary a correction factor due
to loss of sensitivity with accumulated dose.
Abstract: This paper presents the results of thermo-mechanical
characterization of Glass/Epoxy composite specimens using Infrared
Thermography technique. The specimens used for the study were
fabricated in-house with three different lay-up sequences and tested
on a servo hydraulic machine under uni-axial loading. Infrared
Camera was used for on-line monitoring surface temperature changes
of composite specimens during tensile deformation.
Experimental results showed that thermomechanical
characteristics of each type of specimens were distinct. Temperature
was found to be decreasing linearly with increasing tensile stress in
the elastic region due to thermo-elastic effect. Yield point could be
observed by monitoring the change in temperature profile during
tensile testing and this value could be correlated with the results
obtained from stress-strain response. The extent of prior plastic
deformation in the post-yield region influenced the slopes of
temperature response during tensile loading. Partial unloading and
reloading of specimens post-yield results in change in slope in elastic
and plastic regions of composite specimens.
Abstract: Thermodynamics characterization Sesame oil
extraction by Acetone, Hexane and Benzene has been evaluated. The
120 hours experimental Data were described by a simple
mathematical model. According to the simulation results and the
essential criteria, Acetone is superior to other solvents but under
certain conditions where oil extraction takes place Hexane is superior
catalyst.
Abstract: The counting process of cell colonies is always a long
and laborious process that is dependent on the judgment and ability
of the operator. The judgment of the operator in counting can vary in
relation to fatigue. Moreover, since this activity is time consuming it
can limit the usable number of dishes for each experiment. For these
purposes, it is necessary that an automatic system of cell colony
counting is used. This article introduces a new automatic system of
counting based on the elaboration of the digital images of cellular
colonies grown on petri dishes. This system is mainly based on the
algorithms of region-growing for the recognition of the regions of
interest (ROI) in the image and a Sanger neural net for the
characterization of such regions. The better final classification is
supplied from a Feed-Forward Neural Net (FF-NN) and confronted
with the K-Nearest Neighbour (K-NN) and a Linear Discriminative
Function (LDF). The preliminary results are shown.
Abstract: The cup method is applied for the measurement of water vapor transport properties of porous materials worldwide. However, in practical applications the experimental results are often used without taking into account some secondary effects which can play an important role under specific conditions. In this paper, the effect of temperature on water vapor transport properties of cellular concrete is studied, together with the influence of sample thickness. At first, the bulk density, matrix density, total open porosity and sorption and desorption isotherms are measured for material characterization purposes. Then, the steady state cup method is used for determination of water vapor transport properties, whereas the measurements are performed at several temperatures and for three different sample thicknesses.