Abstract: Photo-crosslinked rice starch-based biodegradable
films were prepared by casting film-solution on leveled trays and
ultra violet (UV) irradiation was applied for 10 minute. The effect of
the content (3%, 6% and 9 wt. %)of photosensitiser (sodium
benzoate) on mechanical properties, water vapor permeability (WVP)
and structural properties of rice starch films were investigated. The
tensile strength increased while elongation at break and water
resistance properties of rice starch films decreased with addition and
increasing content of photosensitiser. The % crystallinity of rice
starch films were decreased when the content of photosensitiser
increased and UV were applied. The results showed that the
carboxylate group band of sodium benzoate was found in the FTIR
spectrum of rice starch films and found that incorporation of 6% of
photosensitiser into the films showed a higher absorption band of
resulted films. This result pointed out the highest interaction between
starch molecules was occurred.
Abstract: The construction of a civil structure inside a urban
area inevitably modifies the outdoor microclimate at the building
site. Wind speed, wind direction, air pollution, driving rain, radiation
and daylight are some of the main physical aspects that are subjected
to the major changes. The quantitative amount of these modifications
depends on the shape, size and orientation of the building and on its
interaction with the surrounding environment.The flow field over a
flat roof model building has been numerically investigated in order to
determine two-dimensional CFD guidelines for the calculation of the
turbulent flow over a structure immersed in an atmospheric boundary
layer. To this purpose, a complete validation campaign has been
performed through a systematic comparison of numerical simulations
with wind tunnel experimental data.Several turbulence models and
spatial node distributions have been tested for five different vertical
positions, respectively from the upstream leading edge to the
downstream bottom edge of the analyzed model. Flow field
characteristics in the neighborhood of the building model have been
numerically investigated, allowing a quantification of the capabilities
of the CFD code to predict the flow separation and the extension of
the recirculation regions.The proposed calculations have allowed the
development of a preliminary procedure to be used as a guidance in
selecting the appropriate grid configuration and corresponding
turbulence model for the prediction of the flow field over a twodimensional
roof architecture dominated by flow separation.
Abstract: The morphology, mineralogical and chemical
composition of a low-grade nickel ore from Mpumalanga, South
Africa, were studied by scanning electron microscope (SEM), X-ray
diffraction (XRD) and X-ray fluorescence (XRF), respectively. The
ore was subjected to atmospheric agitation leaching using sulphuric
acid to investigate the effects of acid concentration, leaching
temperature, leaching time and particle size on extraction of nickel
and cobalt. Analyses results indicated the ore to be a saprolitic nickel
laterite belonging to the serpentine group of minerals. Sulphuric acid
was found to be able to extract nickel from the ore. Increased acid
concentration and temperature only produced low amounts of nickel
but improved cobalt extraction. As high as 77.44% Ni was achieved
when leaching a -106+75μm fraction with 4.0M acid concentration at
25oC. The kinetics of nickel leaching from the saprolitic ore were
studied and the activation energy was determined to be 18.16kJ/mol.
This indicated that nickel leaching reaction was diffusion controlled.
Abstract: This paper gives an overview of a deep drawing
process by pressurized liquid medium separated from the sheet by a
rubber diaphragm. Hydroforming deep drawing processing of sheet
metal parts provides a number of advantages over conventional
techniques. It generally increases the depth to diameter ratio possible
in cup drawing and minimizes the thickness variation of the drawn
cup. To explore the deformation mechanism, analytical and
numerical simulations are used for analyzing the drawing process of
an AA6061-T4 blank. The effects of key process parameters such as
coefficient of friction, initial thickness of the blank and radius
between cup wall and flange are investigated analytically and
numerically. The simulated results were in good agreement with the
results of the analytical model. According to finite element
simulations, the hydroforming deep drawing method provides a more
uniform thickness distribution compared to conventional deep
drawing and decreases the risk of tearing during the process.
Abstract: In this paper, fully developed flow and heat transfer of
viscoelastic materials in curved ducts with square cross section under
constant heat flux have been investigated. Here, staggered mesh is
used as computational grids and flow and heat transfer parameters
have been allocated in this mesh with marker and cell method.
Numerical solution of governing equations has being performed with
FTCS finite difference method. Furthermore, Criminale-Eriksen-
Filbey (CEF) constitutive equation has being used as viscoelastic
model. CEF constitutive equation is a suitable model for studying
steady shear flow of viscoelastic materials which is able to model
both effects of the first and second normal stress differences. Here, it
is shown that the first and second normal stresses differences have
noticeable and inverse effect on secondary flows intensity and mean
Nusselt number which is the main novelty of current research.
Abstract: Tumor cells have an invasive and metastatic phenotype
that is the main cause of death for cancer patients. Tumor
establishment and penetration consists of a series of complex
processes involving multiple changes in gene expression. In this study,
intraperitoneal administration of a high concentration of ascorbic acid
inhibited tumor establishment and decreased tumor mass in BALB/C
mice implanted with S-180 sarcoma cancer cells. To identify proteins
involved in the ascorbic acid-mediated inhibition of tumor
progression, changes in the tumor proteome associated with ascorbic
acid treatment of BALB/C mice implanted with S-180 were
investigated using two-dimensional gel electrophoresis and mass
spectrometry. Twenty protein spots were identified whose expression
was different between control and ascorbic acid treatment groups.
Abstract: This paper made an attempt to investigate the problem associated with enhancement of emulsions of light crude oil-water recovery in an oil field of Algerian Sahara. Measurements were taken through experiments using RheoStress (RS600). Factors such as shear rate, temperature and light oil concentration on the viscosity behavior were considered. Experimental measurements were performed in terms of shear stress–shear rate, yield stress and flow index on mixture of light crude oil–water. The rheological behavior of emulsion showed Non-Newtonian shear thinning behavior (Herschel-Bulkley). The experiments done in the laboratory showed the stability of some water in light crude oil emulsions form during consolidate oil recovery process. To break the emulsion using additives may involve higher cost and could be very expensive. Therefore, further research should be directed to find solution of these problems that have been encountered.
Abstract: Study of fire and explosion is very important mainly
in oil and gas industries due to several accidents which have been
reported in the past and present. In this work, we have investigated
the flammability of bio oil vapour mixtures. This mixture may
contribute to fire during the storage and transportation process. Bio
oil sample derived from Palm Kernell shell was analysed using Gas
Chromatography Mass Spectrometry (GC-MS) to examine the
composition of the sample. Mole fractions of 12 selected
components in the liquid phase were obtained from the GC-FID data
and used to calculate mole fractions of components in the gas phase
via modified Raoult-s law. Lower Flammability Limits (LFLs) and
Upper Flammability Limits (UFLs) for individual components were
obtained from published literature. However, stoichiometric
concentration method was used to calculate the flammability limits
of some components which their flammability limit values are not
available in the literature. The LFL and UFL values for the mixture
were calculated using the Le Chatelier equation. The LFLmix and
UFLmix values were used to construct a flammability diagram and
subsequently used to determine the flammability of the mixture. The
findings of this study can be used to propose suitable inherently
safer method to prevent the flammable mixture from occurring and
to minimizing the loss of properties, business, and life due to fire
accidents in bio oil productions.
Abstract: Semisolid metal processing uses solid–liquid slurries
containing fine and globular solid particles uniformly distributed in a
liquid matrix, which can be handled as a solid and flow like a liquid.
In the recent years, many methods have been introduced for the
production of semisolid slurries since it is scientifically sound and
industrially viable with such preferred microstructures called
thixotropic microstructures as feedstock materials. One such process
that needs very low equipment investment and running costs is the
cooling slope. In this research by using a mechanical stirrer slurry
maker constructed by the authors, the effects of mechanical stirring
parameters such as: stirring time, stirring temperature and stirring
Speed on micro-structure and mechanical properties of A360
aluminum alloy in semi-solid forming, are investigated. It is
determined that mold temperature and holding time of part in
temperature of 580ºC have a great effect on micro-structure and
mechanical properties(stirring temperature of 585ºC, stirring time of
20 minutes and stirring speed of 425 RPM). By optimizing the
forming parameters, dendrite microstructure changes to globular and
mechanical properties improves. This is because of breaking and
globularzing dendrites of primary α-AL.
Abstract: Numerical study of two dimensional supersonic
hydrogen-air mixing layer is performed to investigate the effect of
turbulence and chemical additive on ignition distance. Chemical
reaction is treated using detail kinetics. Advection upstream splitting
method is used to calculate the fluxes and one equation turbulence
model is chosen here to simulate the considered problem. Hydrogen
peroxide is used as an additive and the results show that inflow
turbulence and chemical additive may drastically decrease the
ignition delay in supersonic combustion.
Abstract: The equilibrium chemical reactions taken place in a converter reactor of the Khorasan Petrochemical Ammonia plant was studied using the minimization of Gibbs free energy method. In the minimization of the Gibbs free energy function the Davidon– Fletcher–Powell (DFP) optimization procedure using the penalty terms in the well-defined objective function was used. It should be noted that in the DFP procedure along with the corresponding penalty terms the Hessian matrices for the composition of constituents in the Converter reactor can be excluded. This, in fact, can be considered as the main advantage of the DFP optimization procedure. Also the effect of temperature and pressure on the equilibrium composition of the constituents was investigated. The results obtained in this work were compared with the data collected from the converter reactor of the Khorasan Petrochemical Ammonia plant. It was concluded that the results obtained from the method used in this work are in good agreement with the industrial data. Notably, the algorithm developed in this work, in spite of its simplicity, takes the advantage of short computation and convergence time.
Abstract: A numerical investigation of surface heat transfer
characteristics of turbulent air flows in different parallel plate
grooved channels is performed using CFD code. The results are
obtained for Reynolds number ranging from 10,000 to 30,000 and for
arc-shaped and rectangular grooved channels. The influence of
different geometric parameters of dimples as well as the number of
them and the geometric and thermophysical properties of channel
walls are studied. It is found that there exists an optimum value for
depth of dimples in which the largest wall heat flux can be achieved.
Also, the results show a critical value for the ratio of wall thermal
conductivity to the one of fluid in which the dependence of wall heat
flux to this ratio almost vanishes. In most cases examined, heat
transfer enhancement is larger for arc-shaped grooved channels than
rectangular ones.
Abstract: This paper aims at to develop a robust optimization methodology for the mechatronic modules of machine tools by considering all important characteristics from all structural and control domains in one single process. The relationship between these two domains is strongly coupled. In order to reduce the disturbance caused by parameters in either one, the mechanical and controller design domains need to be integrated. Therefore, the concurrent integrated design method Design For Control (DFC), will be employed in this paper. In this connect, it is not only applied to achieve minimal power consumption but also enhance structural performance and system response at same time. To investigate the method for integrated optimization, a mechatronic feed drive system of the machine tools is used as a design platform. Pro/Engineer and AnSys are first used to build the 3D model to analyze and design structure parameters such as elastic deformation, nature frequency and component size, based on their effects and sensitivities to the structure. In addition, the robust controller,based on Quantitative Feedback Theory (QFT), will be applied to determine proper control parameters for the controller. Therefore, overall physical properties of the machine tool will be obtained in the initial stage. Finally, the technology of design for control will be carried out to modify the structural and control parameters to achieve overall system performance. Hence, the corresponding productivity is expected to be greatly improved.
Abstract: In order to study the effect of plant density and
competition of wheat with field bindweed (Convolvulus arvensis) on
yield and agronomical properties of wheat(Triticum Sativum) in
irrigated conditions, a factorial experiment as the base of complete
randomize block design in three replication was conducted at the
field of Kamalvand in khoramabad (Lorestan) region of Iran during
2008-2009. Three plant density (Factor A=200, 230 and 260kg/ha)
three cultivar (Factor B=Bahar,Pishtaz and Alvand) and weed control
(Factor C= control and no control of weeds)were assigned in
experiment. Results show that: Plant density had significant effect
(statistically) on seed yield, 1000 seed weight, weed density and dry
weight of weeds, seed yield and harvest index had been meaningful
effect for cultivars. The interaction between plant density and
cultivars for weed density, seed yield, thousand seed weight and
harvest index were significant. 260 kg/ha (plant density) of wheat had
more effect on increasing of seed yield in Bahar cultivar wheat in
khoramabad region of Iran.
Abstract: Safety, river environment, and sediment utilization are the elements of the target of sediment management. As a change in an element by sediment management, may affect the other two elements, and the priority among three elements depends on stakeholders. It is necessary to develop a method to evaluate the effect of sediment management on each element and an integrated evaluation method for socio-economic effect. In this study, taking Mount Merapi basin as an investigation field, the method for an active volcanic basin was developed. An integrated evaluation method for sediment management was discussed from a socio-economic point on safety, environment, and sediment utilization and a case study of sediment management was evaluated by means of this method. To evaluate the effect of sediment management, some parameters on safety, utilization, and environment have been introduced. From a utilization point of view, job opportunity, additional income of local people, and tax income to local government were used to evaluate the effectiveness of sediment management. The risk degree of river infrastructure was used to describe the effect of sediment management on a safety aspect. To evaluate the effects of sediment management on environment, the mean diameter of grain size distribution of riverbed surface was used. On the coordinate system designating these elements, the direction of change in basin condition by sediment management can be predicted, so that the most preferable sediment management can be decided. The results indicate that the cases of sediment management tend to give the negative impacts on sediment utilization. However, these sediment managements will give positive impacts on safety and environment condition. Evaluation result from a social-economic point of view shows that the case study of sediment management reduces job opportunity and additional income for inhabitants as well as tax income for government. Therefore, it is necessary to make another policy for creating job opportunity for inhabitants to support these sediment managements.
Abstract: In this work we investigated the behavior of methane
hydrates dispersed in crude oils from different fields at temperatures
below 0°C. In case of crude oil emulsion the size of water droplets is
in the range of 50e100"m. The size of hydrate particles formed from
droplets is the same. The self-preservation is not expected in this
field. However, the self-preservation of hydrates with the size of
particles 24±18"m (electron microscopy data) in suspensions is
observed. Similar results were obtained for four different kinds of
crude oil and model system such as asphaltenes, resins and wax in ndecane.
This result can allow developing effective methods to prevent
the formation and elimination of gas-hydrate plugs in pipelines under
low temperature conditions (e. g. in Eastern Siberia). There is a
prospective to use experiment results for working out the technology
of associated petroleum gas recovery.
Abstract: This paper shows how we can integrate
communication modeling into the design modeling at early stages of
the design flow. We consider effect of incorporating noise such as
impulsive noise on system stability. We show that with change of the
system model and investigate the system performance under the
different communication effects. We modeled a unmanned aerial
vehicle (UAV) as a demonstration using SystemC methodology.
Moreover the system is modeled by joining the capabilities of UML
and SystemC to operate at system level.
Abstract: A Laboratory-scale packed bed reactor with microbial
cellulose as the biofilm carrier was used to investigate the
denitrification of high-strength nitrate wastewater with specific
emphasis on the effect the nitrogen loading rate and hydraulic
retention time. Ethanol was added as a carbon source for
denitrification. As a result of this investigation, it was found that up
to 500 mg/l feed nitrate concentration the present system is able to
produce an effluent with nitrate content below 10 ppm at 3 h
hydraulic retention time. The highest observed denitrification rate
was 4.57 kg NO3-N/ (m3 .d) at a nitrate load of 5.64 kg NO3-
N/(m3 .d), and removal efficiencies higher than 90% were obtained
for loads up to 4.2 kg NO3-N/(m3 .d). A mass relation between COD
consumed and NO3-N removed around 2.82 was observed. This
continuous-flow bioreactor proved an efficient denitrification system
with a relatively low retention time.
Abstract: Through inward perceptions, we intuitively expect
distributed software development to increase the risks associated with
achieving cost, schedule, and quality goals. To compound this
problem, agile software development (ASD) insists one of the main
ingredients of its success is cohesive communication attributed to
collocation of the development team. The following study identified
the degree of communication richness needed to achieve comparable
software quality (reduce pre-release defects) between distributed and
collocated teams. This paper explores the relevancy of
communication richness in various development phases and its
impact on quality. Through examination of a large distributed agile
development project, this investigation seeks to understand the levels
of communication required within each ASD phase to produce
comparable quality results achieved by collocated teams. Obviously,
a multitude of factors affects the outcome of software projects.
However, within distributed agile software development teams, the
mode of communication is one of the critical components required to
achieve team cohesiveness and effectiveness. As such, this study
constructs a distributed agile communication model (DAC-M) for
potential application to similar distributed agile development efforts
using the measurement of the suitable level of communication. The
results of the study show that less rich communication methods, in
the appropriate phase, might be satisfactory to achieve equivalent
quality in distributed ASD efforts.
Abstract: Dynamic shear test on simulated phantom can be used
to validate magnetic resonance elastography (MRE) measurements.
Phantom gel has been usually utilized for the cell culture of cartilage
and soft tissue and also been used for mechanical property
characterization using imaging systems. The viscoelastic property of
the phantom would be important for dynamic experiments and
analyses. In this study, An axisymmetric FE model is presented for
determining the dynamic shear behaviour of brain simulated phantom
using ABAQUS. The main objective of this study was to investigate
the effect of excitation frequencies and boundary conditions on shear
modulus and shear viscosity in viscoelastic media.