Abstract: The present paper was concerned primarily with the
analysis, simulation of the air flow and thermal patterns in a lecture
room. The paper is devoted to numerically investigate the influence
of location and number of ventilation and air conditioning supply and
extracts openings on air flow properties in a lecture room. The work
focuses on air flow patterns, thermal behaviour in lecture room where
large number of students. The effectiveness of an air flow system is
commonly assessed by the successful removal of sensible and latent
loads from occupants with additional of attaining air pollutant at a
prescribed level to attain the human thermal comfort conditions and
to improve the indoor air quality; this is the main target during the
present paper. The study is carried out using computational fluid
dynamics (CFD) simulation techniques as embedded in the
commercially available CFD code (FLUENT 6.2). The CFD
modelling techniques solved the continuity, momentum and energy
conservation equations in addition to standard k – ε model equations
for turbulence closure.
Throughout the investigations, numerical validation is carried out by
way of comparisons of numerical and experimental results. Good
agreement is found among both predictions.
Abstract: Addition of milli or micro sized particles to the heat
transfer fluid is one of the many techniques employed for improving
heat transfer rate. Though this looks simple, this method has
practical problems such as high pressure loss, clogging and erosion
of the material of construction. These problems can be overcome by
using nanofluids, which is a dispersion of nanosized particles in a
base fluid. Nanoparticles increase the thermal conductivity of the
base fluid manifold which in turn increases the heat transfer rate.
Nanoparticles also increase the viscosity of the basefluid resulting in
higher pressure drop for the nanofluid compared to the base fluid. So
it is imperative that the Reynolds number (Re) and the volume
fraction have to be optimum for better thermal hydraulic
effectiveness. In this work, the heat transfer enhancement using
aluminium oxide nanofluid using low and high volume fraction
nanofluids in turbulent pipe flow with constant wall temperature has
been studied by computational fluid dynamic modeling of the
nanofluid flow adopting the single phase approach. Nanofluid, up till
a volume fraction of 1% is found to be an effective heat transfer
enhancement technique. The Nusselt number (Nu) and friction factor
predictions for the low volume fractions (i.e. 0.02%, 0.1 and 0.5%)
agree very well with the experimental values of Sundar and Sharma
(2010). While, predictions for the high volume fraction nanofluids
(i.e. 1%, 4% and 6%) are found to have reasonable agreement with
both experimental and numerical results available in the literature.
So the computationally inexpensive single phase approach can be
used for heat transfer and pressure drop prediction of new nanofluids.
Abstract: Experiments have been carried out at sub-critical
Reynolds number to investigate free-to-roll motions induced by
forebody and/or wings complex flow on a 30° swept back nonslender
wings-slender body-model for static and dynamic (pitch-up)
cases. For the dynamic (pitch-up) case it has been observed that roll
amplitude decreases and lag increases with increase in pitching
speed. Decrease in roll amplitude with increase in pitch rate is
attributed to low disturbing rolling moment due to weaker interaction
between forebody and wing flow components. Asymmetric forebody
vortices dominate and control the roll motion of the model in
dynamic case when non-dimensional pitch rate ≥ 1x10-2.
Effectiveness of the active control scheme utilizing rotating nose with
artificial tip perturbation is observed to be low in the angle of attack
region where the complex flow over the wings has contributions from
both forebody and wings.
Abstract: In rapidly changing market environment, firms are investing a lot of time and resources into new product development (NPD) projects to make profit and to obtain competitive advantage. However, failure rate of NPD projects is becoming high due to various internal and external risks which hinder successful NPD projects. To reduce the failure rate, it is critical that risks have to be managed effectively and efficiently through good strategy, and treated by optimal responses to minimize risk cost. Four strategies are adopted to handle the risks in this study. The optimal responses are characterized by high reduction of risk costs with high efficiency. This study suggests a framework to decide the optimal responses considering the core risks, risk costs, response efficiency and response costs for successful NPD projects. Both binary particles warm optimization (BPSO) and multi-objective particle swarm optimization (MOPSO) methods are mainly used in the framework. Although several limitations exist in use for real industries, the frame work shows good strength for handling the risks with highly scientific ways through an example.
Abstract: Artifact free photoplethysmographic (PPG) signals are
necessary for non-invasive estimation of oxygen saturation (SpO2) in
arterial blood. Movement of a patient corrupts the PPGs with motion
artifacts, resulting in large errors in the computation of Sp02. This
paper presents a study on using Kalman Filter in an innovative way
by modeling both the Artillery Blood Pressure (ABP) and the
unwanted signal, additive motion artifact, to reduce motion artifacts
from corrupted PPG signals. Simulation results show acceptable
performance regarding LMS and variable step LMS, thus
establishing the efficacy of the proposed method.
Abstract: Quality Function Deployment (QFD) is an expounded, multi-step planning method for delivering commodity, services, and processes to customers, both external and internal to an organization. It is a way to convert between the diverse customer languages expressing demands (Voice of the Customer), and the organization-s languages expressing results that sate those demands. The policy is to establish one or more matrices that inter-relate producer and consumer reciprocal expectations. Due to its visual presence is called the “House of Quality" (HOQ). In this paper, we assumed HOQ in multi attribute decision making (MADM) pattern and through a proposed MADM method, rank technical specifications. Thereafter compute satisfaction degree of customer requirements and for it, we apply vagueness and uncertainty conditions in decision making by fuzzy set theory. This approach would propound supervised neural network (perceptron) for MADM problem solving.
Abstract: The purpose of this paper is to present two different
approaches of financial distress pre-warning models appropriate for
risk supervisors, investors and policy makers. We examine a sample
of the financial institutions and electronic companies of Taiwan
Security Exchange (TSE) market from 2002 through 2008. We
present a binary logistic regression with paned data analysis. With
the pooled binary logistic regression we build a model including
more variables in the regression than with random effects, while the
in-sample and out-sample forecasting performance is higher in
random effects estimation than in pooled regression. On the other
hand we estimate an Adaptive Neuro-Fuzzy Inference System
(ANFIS) with Gaussian and Generalized Bell (Gbell) functions and
we find that ANFIS outperforms significant Logit regressions in both
in-sample and out-of-sample periods, indicating that ANFIS is a
more appropriate tool for financial risk managers and for the
economic policy makers in central banks and national statistical
services.
Abstract: The main focus of the work was concerned with hydrodynamic and thermal analysis of the plate heat exchanger channel with corrugation patterns suggested to be triangular, sinusoidal, and square corrugation. This study was to numerically model and validate the triangular corrugated channel with dimensions/parameters taken from open literature, and then model/analyze both sinusoidal, and square corrugated channel referred to the triangular model. Initially, 2D modeling with local extensive analysis for triangular corrugated channel was carried out. By that, all local pressure drop, wall shear stress, friction factor, static temperature, heat flux, Nusselt number, and surface heat coefficient, were analyzed to interpret the hydrodynamic and thermal phenomena occurred in the flow. Furthermore, in order to facilitate confidence in this model, a comparison between the values predicted, and experimental results taken from literature for almost the same case, was done. Moreover, a holistic numerical study for sinusoidal and square channels together with global comparisons with triangular corrugation under the same condition, were handled. Later, a comparison between electric, and fluid cooling through varying the boundary condition was achieved. The constant wall temperature and constant wall heat flux boundary conditions were employed, and the different resulted Nusselt numbers as a consequence were justified. The results obtained can be used to come up with an optimal design, a 'compromise' between heat transfer and pressure drop.
Abstract: The algorithm represents the DCT coefficients to concentrate signal energy and proposes combination and dictator to eliminate the correlation in the same level subband for encoding the DCT-based images. This work adopts DCT and modifies the SPIHT algorithm to encode DCT coefficients. The proposed algorithm also provides the enhancement function in low bit rate in order to improve the perceptual quality. Experimental results indicate that the proposed technique improves the quality of the reconstructed image in terms of both PSNR and the perceptual results close to JPEG2000 at the same bit rate.
Abstract: This paper proposes a modeling methodology for the
development of data analysis solution. The Author introduce the
approach to address data warehousing issues at the at enterprise level.
The methodology covers the process of the requirements eliciting and
analysis stage as well as initial design of data warehouse. The paper
reviews extended business process model, which satisfy the needs of
data warehouse development. The Author considers that the use of
business process models is necessary, as it reflects both enterprise
information systems and business functions, which are important for
data analysis. The Described approach divides development into
three steps with different detailed elaboration of models. The
Described approach gives possibility to gather requirements and
display them to business users in easy manner.
Abstract: This paper demonstrates the results when either
Shiftrows stage or Mixcolumns stage and when both the stages are
omitted in the well known block cipher Advanced Encryption
Standard(AES) and its modified version AES with Key Dependent
S-box(AES-KDS), using avalanche criterion and other tests namely
encryption quality, correlation coefficient, histogram analysis and
key sensitivity tests.
Abstract: In Algeria, liberalization reforms undertaken since the 1990s have resulted in negative effects on the development and management of irrigation schemes, as well as on the conditions of farmers. Reforms have been undertaken to improve the performance of irrigation schemes, such as the national plan of agricultural development (PNDA) in 2000 and the water pricing policy of 2005. However, after implementation of these policies, questions have arisen with regard to irrigation performance and its suitability for agricultural development. Hence, the aim of this paper is to provide insight into the profitability of irrigation during the transition period under current irrigation agricultural policies in Algeria. By using the method of farm crop budget analysis in the East Mitidja irrigation scheme, the returns from using surface water resources based on farm typology were found to vary among crops and farmers- groups within the scheme. Irrigation under the current situation is profitable for all farmers, including both those who benefit from subsidies and those who do not. However, the returns to water were found to be very sensitive to crop price fluctuations, particularly for non-subsidized groups and less so for those whose farming is based on orchards. Moreover, the socio-economic environment of the farmers contributed to less significant impacts of the PNDA policy. In fact, the limiting factor is not only the water, but also the lack of land ownership title. Market access constraints led to less agricultural investment and therefore to low intensification and low water productivity. It is financially feasible to recover the annual O&M costs in the irrigation scheme. By comparing the irrigation water price, returns to water, and O&M costs of water delivery, it is clear that irrigation can be profitable in the future. However, water productivity must be improved by enhancing farmers- income through farming investment, improving assets access, and the allocation of activities and crops which bring high returns to water; this could allow the farmers to pay more for water and allow cost recovery for water systems.
Abstract: Recently, wireless sensor networks have been paid
more interest, are widely used in a lot of commercial and military
applications, and may be deployed in critical scenarios (e.g. when a
malfunctioning network results in danger to human life or great
financial loss). Such networks must be protected against human
intrusion by using the secret keys to encrypt the exchange messages
between communicating nodes. Both the symmetric and asymmetric
methods have their own drawbacks for use in key management. Thus,
we avoid the weakness of these two cryptosystems and make use of
their advantages to establish a secure environment by developing the
new method for encryption depending on the idea of code
conversion. The code conversion-s equations are used as the key for
designing the proposed system based on the basics of logic gate-s
principals. Using our security architecture, we show how to reduce
significant attacks on wireless sensor networks.
Abstract: The paper presents a computational tool developed for
the evaluation of technical and economic advantages of an innovative
cleaning and conditioning technology of fluidized bed steam/oxygen
gasifiers outlet product gas. This technology integrates into a single
unit the steam gasification of biomass and the hot gas cleaning and
conditioning system. Both components of the computational tool,
process flowsheet and economic evaluator, have been developed
under IPSEpro software. The economic model provides information
that can help potential users, especially small and medium size
enterprises acting in the regenerable energy field, to decide the
optimal scale of a plant and to better understand both potentiality and
limits of the system when applied to a wide range of conditions.
Abstract: Multimedia information availability has increased
dramatically with the advent of video broadcasting on handheld
devices. But with this availability comes problems of maintaining the
security of information that is displayed in public. ISMA Encryption
and Authentication (ISMACryp) is one of the chosen technologies for
service protection in DVB-H (Digital Video Broadcasting-
Handheld), the TV system for portable handheld devices. The
ISMACryp is encoded with H.264/AVC (advanced video coding),
while leaving all structural data as it is. Two modes of ISMACryp are
available; the CTR mode (Counter type) and CBC mode (Cipher
Block Chaining) mode. Both modes of ISMACryp are based on 128-
bit AES algorithm. AES algorithms are more complex and require
larger time for execution which is not suitable for real time
application like live TV. The proposed system aims to gain a deep
understanding of video data security on multimedia technologies and
to provide security for real time video applications using selective
encryption for H.264/AVC. Five level of security proposed in this
paper based on the content of NAL unit in Baseline Constrain profile
of H.264/AVC. The selective encryption in different levels provides
encryption of intra-prediction mode, residue data, inter-prediction
mode or motion vectors only. Experimental results shown in this
paper described that fifth level which is ISMACryp provide higher
level of security with more encryption time and the one level provide
lower level of security by encrypting only motion vectors with lower
execution time without compromise on compression and quality of
visual content. This encryption scheme with compression process
with low cost, and keeps the file format unchanged with some direct
operations supported. Simulation was being carried out in Matlab.
Abstract: The Wavelet-Galerkin finite element method for
solving the one-dimensional heat equation is presented in this work.
Two types of basis functions which are the Lagrange and multi-level
wavelet bases are employed to derive the full form of matrix system.
We consider both linear and quadratic bases in the Galerkin method.
Time derivative is approximated by polynomial time basis that
provides easily extend the order of approximation in time space. Our
numerical results show that the rate of convergences for the linear
Lagrange and the linear wavelet bases are the same and in order 2
while the rate of convergences for the quadratic Lagrange and the
quadratic wavelet bases are approximately in order 4. It also reveals
that the wavelet basis provides an easy treatment to improve
numerical resolutions that can be done by increasing just its desired
levels in the multilevel construction process.
Abstract: The design of Automatic Generation Control (AGC) system plays a vital role in automation of power system. This paper proposes Hybrid Neuro Fuzzy (HNF) approach for AGC of two-area interconnected reheat thermal power system with the consideration of Generation Rate Constraint (GRC). The advantage of proposed controller is that it can handle the system non-linearities and at the same time the proposed approach is faster than conventional controllers. The performance of HNF controller has been compared with that of both conventional Proportional Integral (PI) controller as well as Fuzzy Logic Controller (FLC) both in the absence and presence of Generation Rate Constraint (GRC). System performance is examined considering disturbance in each area of interconnected power system.
Abstract: Decision fusion is one of hot research topics in
classification area, which aims to achieve the best possible
performance for the task at hand. In this paper, we
investigate the usefulness of this concept to improve change
detection accuracy in remote sensing. Thereby, outputs of
two fuzzy change detectors based respectively on
simultaneous and comparative analysis of multitemporal
data are fused by using fuzzy integral operators. This
method fuses the objective evidences produced by the
change detectors with respect to fuzzy measures that express
the difference of performance between them. The proposed
fusion framework is evaluated in comparison with some
ordinary fuzzy aggregation operators. Experiments carried
out on two SPOT images showed that the fuzzy integral was
the best performing. It improves the change detection
accuracy while attempting to equalize the accuracy rate in
both change and no change classes.
Abstract: Road crashes not only claim lives and inflict injuries but also create economic burden to the society due to loss of productivity. The problem of deaths and injuries as a result of road traffic crashes is now acknowledged to be a global phenomenon with authorities in virtually all countries of the world concerned about the growth in the number of people killed and seriously injured on their roads. However, the road crash scenario of a developing country like Bangladesh is much worse comparing with this of developed countries. For developing proper countermeasures it is necessary to identify the factors affecting crash occurrences. The objectives of the study is to examine the effect of district wise road infrastructure, socioeconomic and demographic features on crash occurrence .The unit of analysis will be taken as individual district which has not been explored much in the past. Reported crash data obtained from Bangladesh Road Transport Authority (BRTA) from the year 2004 to 2010 are utilized to develop negative binomial model. The model result will reveal the effect of road length (both paved and unpaved), road infrastructure and several socio economic characteristics on district level crash frequency in Bangladesh.
Abstract: This paper tries to represent a new method for
computing the reliability of a system which is arranged in series or
parallel model. In this method we estimate life distribution function
of whole structure using the asymptotic Extreme Value (EV)
distribution of Type I, or Gumbel theory. We use EV distribution in
minimal mode, for estimate the life distribution function of series
structure and maximal mode for parallel system. All parameters also
are estimated by Moments method. Reliability function and failure
(hazard) rate and p-th percentile point of each function are
determined. Other important indexes such as Mean Time to Failure
(MTTF), Mean Time to repair (MTTR), for non-repairable and
renewal systems in both of series and parallel structure will be
computed.