Abstract: Borate minerals have attracted considerable attention in the past years due to their structural chemistry and mechanical properties in several industries. Recently, increasing attention has been paid to the use of; synthetically produced magnesium borates as catalysts reinforcing material for plastics, the conversion of hydrocarbons, electro-conductive treating agent, anti-wear and anti-corrosion materials. Magnesium borates can be synthesized by several methods such as; hydrothermal and solid-state (thermal) processes. In this study the hydrothermal production method was applied at the modest temperature of 80C along with convenient crystal growth. Using MgCl2.6H2O, H3BO3, and NaOH as starting materials, 30, 60, 120, 240 minutes of reaction times were studied. After all, the crystal structure and the morphology of the products were examined by X-Ray Diffraction (XRD) and Fourier Transform Infrared Spectroscopy (FT-IR). As a result the forms of Admontite and Mcallisterite minerals were synthesized.
Abstract: In this paper, Zinc Oxide (ZnO) thin films are deposited on glass substrate by sol-gel method. The ZnO thin films with well defined orientation were acquired by spin coating of zinc acetate dehydrate monoethanolamine (MEA), de-ionized water and isopropanol alcohol. These films were pre-heated at 275°C for 10 min and then annealed at 350°C, 450°C and 550°C for 80 min. The effect of annealing temperature and different thickness on structure and surface morphology of the thin films were verified by Atomic Force Microscopy (AFM). It was found that there was a significant effect of annealing temperature on the structural parameters of the films such as roughness exponent, fractal dimension and interface width. Thin films also were characterizied by X-ray Diffractometery (XRD) method. XRD analysis revealed that the annealed ZnO thin films consist of single phase ZnO with wurtzite structure and show the c-axis grain orientation. Increasing annealing temperature increased the crystallite size and the c-axis orientation of the film after 450°C. Also In this study, ZnO thin films in different thickness have been prepared by sol-gel method on the glass substrate at room temperature. The thicknesses of films are 100, 150 and 250 nm. Using fractal analysis, morphological characteristics of surface films thickness in amorphous state were investigated. The results show that with increasing thickness, surface roughness (RMS) and lateral correlation length (ξ) are decreased. Also, the roughness exponent (α) and growth exponent (β) were determined to be 0.74±0.02 and 0.11±0.02, respectively.
Abstract: The advantage of solving the complex nonlinear
problems by utilizing fuzzy logic methodologies is that the
experience or expert-s knowledge described as a fuzzy rule base can
be directly embedded into the systems for dealing with the problems.
The current limitation of appropriate and automated designing of
fuzzy controllers are focused in this paper. The structure discovery
and parameter adjustment of the Branched T-S fuzzy model is
addressed by a hybrid technique of type constrained sparse tree
algorithms. The simulation result for different system model is
evaluated and the identification error is observed to be minimum.
Abstract: Zinc borates can be used as multi-functional
synergistic additives with flame retardant additives in polymers. Zinc
borate is white, non-hygroscopic and powder type product. The most
important properties are low solubility in water and high dehydration
temperature. Zinc borates dehydrate above 290°C and anhydrous zinc
borate has thermal resistance about 400°C. Zinc borates can be
synthesized using several methods such as hydrothermal and solidstate
processes. In this study, the solid-state method was applied at
low temperatures of 600oC and 700oC using the starting materials of
ZnO and H3BO3 with several mole ratios. The reaction time was
determined as 4 hours after some preliminary experiments. After the
synthesis, the crystal structure and the morphology of the products
were examined by X-Ray Diffraction (XRD) and Fourier Transform
Infrared Spectroscopy (FT-IR). As a result the forms of ZnB4O7,
Zn3(BO3)2, ZnB2O4 were synthesized and obtained along with the
unreacted ZnO.
Abstract: Complex systems are composed of several plain interacting independent entities. Interaction between these entities creates a unified behavior at the global level that cannot be predicted by examining the behavior of any single individual component of the system. In this paper we consider a welded frame of an automobile trailer as a real example of Complex Technical Systems, The purpose of this paper is to introduce a Statistical method for predicting the life cycle of complex technical systems. To organize gathering of primary data for modeling the life cycle of complex technical systems an “Automobile Trailer Frame" were used as a prototype in this research. The prototype represents a welded structure of several pieces. Both information flows underwent a computerized analysis and classification for the acquisition of final results to reach final recommendations for improving the trailers structure and their operational conditions.
Abstract: The purposes of this study are 1) to study the over 20-year attempt of Mahakan fort community to negotiate with Bangkok Metropolitan Administration (BMA) to remain in their residential area belonging to the state, and 2) to apply the new social and cultural dimension between the state and the community as an alternative for local participation in keeping their residential area. This is a qualitative research, and the findings reveal that the community claimed their ancestors’ right as owners of this piece of land for over 200 years. The community, therefore, requested to take part in the preservation of land, culture and local intellect and the area management in terms of being a learning resource on the cultural road in Rattanakosin Island. However, BMA imposed the law concerning the community area relocation in Rattanakosin Island. The result of law enforcement led to the failure of the area relocation, and the hard hit on physical structure of the area including the overall deterioration of the cultural road renovated in the year 1982, the 200 years’ celebration of Bangkok. The enforcement of law by the state required the move of the community, and the landscape improvement based on the capital city plan. However, this enforcement resulted in the unending conflicts between the community and the state, and the solution of this problem was unclear. At the same time the community has spent a long time opposing the state’s action, and preparing themselves by administrating the community behind Mahakan fortress with community administrative committee under the suggestion of external organization by registering all community members, providing funds for community administration. At the meantime the state lacked the continuation of the enforcement due to political problem and BMA’s administration problem. It is, therefore, suggested that an alternative solution to this problem lie at the negotiation between the state and the community with the purpose of the collaboration between the two to develop the area under the protective law of each side.
Abstract: In this researcha particle swarm optimization (PSO)
algorithm is proposedfor no-wait flowshopsequence dependent
setuptime scheduling problem with weighted earliness-tardiness
penalties as the criterion (|,
|Σ
"
).The
smallestposition value (SPV) rule is applied to convert the continuous
value of position vector of particles in PSO to job permutations.A
timing algorithm is generated to find the optimal schedule and
calculate the objective function value of a given sequence in PSO
algorithm. Twodifferent neighborhood structures are applied to
improve the solution quality of PSO algorithm.The first one is based
on variable neighborhood search (VNS) and the second one is a
simple one with invariable structure. In order to compare the
performance of two neighborhood structures, random test problems
are generated and solved by both neighborhood
approaches.Computational results show that the VNS algorithmhas
better performance than the other one especially for the large sized
problems.
Abstract: Large-scale systems such as Grids offer
infrastructures for both data distribution and parallel processing. The
use of Grid infrastructures is a more recent issue that is already
impacting the Distributed Database Management System industry. In
DBMS, distributed query processing has emerged as a fundamental
technique for ensuring high performance in distributed databases.
Database placement is particularly important in large-scale systems
because it reduces communication costs and improves resource
usage. In this paper, we propose a dynamic database placement
policy that depends on query patterns and Grid sites capabilities. We
evaluate the performance of the proposed database placement policy
using simulations. The obtained results show that dynamic database
placement can significantly improve the performance of distributed
query processing.
Abstract: The problem of manipulator control is a highly
complex problem of controlling a system which is multi-input, multioutput,
non-linear and time variant. In this paper some adaptive
fuzzy, and a new hybrid fuzzy control algorithm have been
comparatively evaluated through simulations, for manipulator
control. The adaptive fuzzy controllers consist of self-organizing,
self-tuning, and coarse/fine adaptive fuzzy schemes. These
controllers are tested for different trajectories and for varying
manipulator parameters through simulations. Various performance
indices like the RMS error, steady state error and maximum error are
used for comparison. It is observed that the self-organizing fuzzy
controller gives the best performance. The proposed hybrid fuzzy
plus integral error controller also performs remarkably well, given its
simple structure.
Abstract: This paper deals with analysis of flexural stiffness,
indentation and their energies in three point loading of sandwich
beams with composite faces from Eglass/epoxy and cores from
Polyurethane or PVC. Energy is consumed in three stages of
indentation in laminated beam, indentation of sandwich beam and
bending of sandwich beam. Theory of elasticity is chosen to present
equations for indentation of laminated beam, then these equations
have been corrected to offer better results. An analytical model has
been used assuming an elastic-perfectly plastic compressive behavior
of the foam core. Classical theory of beam is used to describe three
point bending. Finite element (FE) analysis of static indentation
sandwich beams is performed using the FE code ABAQUS. The
foam core is modeled using the crushable foam material model and
response of the foam core is experimentally characterized in uniaxial
compression.
Three point bending and indentation have been done
experimentally in two cases of low velocity and higher velocity
(quasi-impact) of loading. Results can describe response of beam in
terms of core and faces thicknesses, core material, indentor diameter,
energy absorbed, and length of plastic area in the testing. The
experimental results are in good agreement with the analytical and
FE analyses. These results can be used as an introduction for impact
loading and energy absorbing of sandwich structures.
Abstract: Delay-Tolerant Networks (DTNs) are sparse, wireless
networks where disconnections are common due to host mobility and
low node density. The Message Ferrying (MF) scheme is a mobilityassisted
paradigm to improve connectivity in DTN-like networks. A
ferry or message ferry is a special node in the network which has
a per-determined route in the deployed area and relays messages
between mobile hosts (MHs) which are intermittently connected.
Increased contact opportunities among mobile hosts and the ferry
improve the performance of the network, both in terms of message
delivery ratio and average end-end delay. However, due to the inherent
mobility of mobile hosts and pre-determined periodicity of the
message ferry, mobile hosts may often -miss- contact opportunities
with a ferry. In this paper, we propose the combination of stationary
ferry access points (FAPs) with MF routing to increase contact
opportunities between mobile hosts and the MF and consequently
improve the performance of the DTN. We also propose several
placement models for deploying FAPs on MF routes. We evaluate the
performance of the FAP placement models through comprehensive
simulation. Our findings show that FAPs do improve the performance
of MF-assisted DTNs and symmetric placement of FAPs outperforms
other placement strategies.
Abstract: In the paper a detailed analysis of the dynamic
response of a cooling tower shell to mining tremors originated from
two main regions of mining activity in Poland (Upper Silesian Coal
Basin and Legnica-Glogow Copper District) was presented. The
representative time histories registered in the both regions were used
as ground motion data in calculations of the dynamic response of the
structure. It was proved that the dynamic response of the shell is
strongly dependent not only on the level of vibration amplitudes but
on the dominant frequency range of the mining shock typical for the
mining region as well. Also a vertical component of vibrations
occurred to have considerable influence on the total dynamic
response of the shell. Finally, it turned out that non-uniformity of
kinematic excitation resulting from spatial variety of ground motion
plays a significant role in dynamic analysis of large-dimensional
shells under mining shocks.
Abstract: The PRAF family of proteins is a plant specific family of proteins with distinct domain architecture and various unique sequence/structure traits. We have carried out an extensive search of the Arabidopsis genome using an automated pipeline and manual methods to verify previously known and identify unknown instances of PRAF proteins, characterize their sequence and build 3D structures of their individual domains. Integrating the sequence, structure and whatever little known experimental details for each of these proteins and their domains, we present a comprehensive characterization of the different domains in these proteins and their variant properties.
Abstract: This paper considers the integration of assembly
operations and product structure to Cellular Manufacturing System
(CMS) design so that to correct the drawbacks of previous researches
in the literature. For this purpose, a new mathematical model is
developed which dedicates machining and assembly operations to
manufacturing cells while the objective function is to minimize the
intercellular movements resulting due to both of them. A
linearization method is applied to achieve optimum solution through
solving aforementioned nonlinear model by common programming
language such as Lingo. Then, using different examples and
comparing the results, the importance of integrating assembly
considerations is demonstrated.
Abstract: This research was conducted to develop a correlation
between microstructure of HSLA steel and the mechanical properties
that occur as a result of both laser and mechanical forming processes
of the metal. The technique of forming flat metals by applying laser
beams is a relatively new concept in the manufacturing industry.
However, the effects of laser energy on the stability of metal alloy
phases have not yet been elucidated in terms of phase
transformations and microhardness. In this work, CO2 laser source
was used to irradiate the surface of a flat metal then the
microstructure and microhardness of the metal were studied on the
formed specimen. The extent to which the microstructure changed
depended on the heat inputs of up to 1000 J/cm2 with cooling rates of
about 4.8E+02 K/s. Experimental results revealed that the irradiated
surface of a HSLA steel had transformed to austenitic structure
during the heating process.
Abstract: Using entropy weight and TOPSIS method, a
comprehensive evaluation is done on the development level of
Chinese regional service industry in this paper. Firstly, based on
existing research results, an evaluation index system is constructed
from the scale of development, the industrial structure and the
economic benefits. An evaluation model is then built up based on
entropy weight and TOPSIS, and an empirical analysis is conducted on
the development level of service industries in 31 Chinese provinces
during 2006 and 2009 from the two dimensions or time series and
cross section, which provides new idea for assessing regional service
industry. Furthermore, the 31 provinces are classified into four
categories based on the evaluation results, and deep analysis is carried
out on the evaluation results.
Abstract: The design of a gravity dam is performed through an
interactive process involving a preliminary layout of the structure
followed by a stability and stress analysis. This study presents a
method to define the optimal top width of gravity dam with genetic
algorithm. To solve the optimization task (minimize the cost of the
dam), an optimization routine based on genetic algorithms (GAs) was
implemented into an Excel spreadsheet. It was found to perform well
and GA parameters were optimized in a parametric study. Using the
parameters found in the parametric study, the top width of gravity
dam optimization was performed and compared to a gradient-based
optimization method (classic method). The accuracy of the results
was within close proximity. In optimum dam cross section, the ratio
of is dam base to dam height is almost equal to 0.85, and ratio of dam
top width to dam height is almost equal to 0.13. The computerized
methodology may provide the help for computation of the optimal
top width for a wide range of height of a gravity dam.
Abstract: The purpose of this study was to examine and
compare physical fitness values of students engaged in different team
sport branches Totally 60 female, and 60 male athletes, that 20
athletes in each branch which are volleyball, basketball and football
participated the study as a volunteer. The mean ages of female and
male athletes were 21.20 ±1.87 and 21.61 ± 1.61 respectively. Age,
height, body weight, body mass index, flexibility, body fat
percentage, 30m sprint, maximum oxygen consumption capacity
(MaxVO2) and drop jump values were measured. As a result of
measurements, significant differences were found in height, weight,
MaxVO2, shuttle run speed between different sports branches in
female athletes. In male athletes, height, body weight, flexibility,
30m split speed and drop jump values were found significantly
different between sports branches.
As a conclusion and as a literature, it can be said that structure of
body has to be appropriate with the engaged sports branch. Physical
fitness values that required the sports branches can be expressed
clearly by increasing the number of subjects.
Abstract: The k-nearest neighbors (knn) is a simple but effective method of classification. In this paper we present an extended version of this technique for chemical compounds used in High Throughput Screening, where the distances of the nearest neighbors can be taken into account. Our algorithm uses kernel weight functions as guidance for the process of defining activity in screening data. Proposed kernel weight function aims to combine properties of graphical structure and molecule descriptors of screening compounds. We apply the modified knn method on several experimental data from biological screens. The experimental results confirm the effectiveness of the proposed method.
Abstract: The present study aims at determining the effect of ageing on the impact toughness and microstructure of 2024 Al-Cu - Mg alloy. Following the 2 h solutionizing treatment at 450°C and water quench, the specimens were aged at 200°C for various periods (1 to 18 h). The precipitation stages during ageing were monitored by hardness measurements. For each specimen group, Charpy impact and hardness tests were carried out. During ageing the impact toughness of the alloy first increased, and then, following a maxima decreased due to the precipitation of intermediate phases, finally it reached its minimum at the peak hardness. Correlations between hardness and impact toughness were investigated.