Abstract: In recent decades, particulate matter (PM10) have
received much attention due to its potential adverse health impact and
the subsequent need to better control or regulate these pollutants.
The aim of this paper is focused on study risk assessment of PM10
in four different districts (Shebikah, Masfalah, Aziziyah, Awali) in
Makkah, Saudi Arabia during the period from 1 Ramadan 1434 AH -
27 Safar 1435 AH. Samples were collected by using Low Volume
Sampler (LVS Low Volume Sampler) device and filtration method
for estimating the total concentration of PM10.
The study indicated that the mean PM10 concentrations were 254.6
(186.1 - 343.2) μg/m3 in Shebikah, 184.9 (145.6 - 271.4) μg/m3 in
Masfalah, 162.4 (92.4-253.8) μg/m3 in Aziziyah, and 56.0 (44.5 -
119.8) μg/m3 in Awali. These values did not exceed the permissible
limits in PME (340 μg/m3 as daily average). Furthermore, health
assessment is carried out using AirQ2.2.3 model to estimate the
number of hospital admissions due to respiratory diseases. The
cumulative number of cases per 100,000 were 1534 (18-3050 case),
which lower than that recorded in the United States, Malaysia. The
concentration response coefficient was 0.49 (95% CI 0.05 - 0.70) per
10 μg/m3 increase of PM10.
Abstract: The study is in application and analysis of two tourism
management tools that can contribute to making public managers
decision: the Barometer of Tourism Sustainability (BTS) and the
Ecological Footprint (EF). The results have shown that BTS allows
you to have an integrated view of the tourism system, awakening to
the need for planning of appropriate actions so that it can achieve the
positive scale proposed (potentially sustainable). Already the
methodology of ecological tourism footprint is an important tool to
measure potential impacts generated by tourism to tourist reality.
Abstract: Zn alloy and composite coatings are widely used in
buildings and structures, automobile and fasteners industries to
protect steel component from corrosion. In this paper, Zn-Ni-Al2O3
nanocomposite coatings were electrodeposited on mild steel using a
novel sol enhanced electroplating method. In this method, transparent
Al2O3 sol was added into the acidic Zn-Ni bath to produced Zn-Ni-
Al2O3 nanocomposite coatings. The effect of alumina sol on the
electrodeposition process, and coating properties was investigated
using cyclic voltammetry, XRD, ESEM and Tafel test. Results from
XRD tests showed that the structure of all coatings was single γ-
Ni5Zn21 phase. Cyclic voltammetry results showed that the
electrodeposition overpotential was lower in the presence of alumina
sol in the bath, and caused the reduction potential of Zn-Ni to shift to
more positive values. Zn-Ni-Al2O3 nanocomposite coatings produced
more uniform and compact deposits, with fine grained microstructure
when compared to Zn-Ni coatings. The corrosion resistance of Zn-Ni
coatings was improved significantly by incorporation of alumina
nanoparticles into the coatings.
Abstract: Contemporary theories of sustainability, concerning
the natural and built environment, have recently introduced an
environmental attitude towards the architectural design that, in turn,
affects the practice of conservation and reuse of the existing building
stock. This paper presents an environmentally friendly approach
towards the conservation of vernacular architecture and it is based on
the results of a research program which involved the investigation of
sustainable design elements of traditional buildings in Cyprus. The
research in question showed that Cypriot vernacular architecture gave
more emphasis on cooling rather than heating strategies. Another
notable finding of the investigation was the great importance given to
courtyards as they enhance considerably, and in various ways, the
microclimatic conditions of the immediate environment with
favorable results throughout the year. Moreover, it was shown that
the reduction in temperature fluctuation observed in the closed and
semi-open spaces, compared to the respective temperature fluctuation
of the external environment -due to the thermal inertia of the building
envelope- helps towards the achievement of more comfortable living
conditions within traditional dwellings. This paper concludes with a
proposal of a sustainable approach towards the conservation of the
existing environment and the introduction of new environmental
criteria for the conservation of traditional buildings, beyond the
aesthetic, morphological and structural ones that are generally
applied.
Abstract: Sodium formate is the chemical substance used for
food additive. Catalase is the important antioxidative enzyme in
protecting the cell from oxidative damage by reactive oxygen species
(ROS). The resultant level of oxidative stress in sodium formatetreated
lymphocytes was investigated. The sodium formate
concentrations of 0.05, 0.1, 0.2, 0.4 and 0.6 mg/mL were treated in
human lymphocytes for 12 hours. After 12 treated hours, catalase
activity change was measured in sodium formate-treated
lymphocytes. The results showed that the sodium formate
concentrations of 0.4 and 0.6 mg/mL significantly decreased catalase
activities in lymphocytes (P < 0.05). The change of catalase activity
in sodium formate-treated lymphocytes may be the oxidative damage
marker for detect sodium formate exposure in human.
Abstract: This paper presents the design, development and
evaluation of an application prototype developed to support
tuberculosis (TB) patients’ treatment adherence. The system makes
use of graphics and voice reminders as opposed to text messaging to
encourage patients to follow their medication routine. To evaluate the
effect of the prototype applications, participants were given mobile
phones on which the reminder system was installed. Thirty-eight
people, including TB health workers and patients from Zanzibar,
Tanzania, participated in the evaluation exercises. The results
indicate that the participants found the mobile image-based
application is useful to support TB treatment. All participants
understood and interpreted the intended meaning of every image
correctly. The study findings revealed that the use of a mobile visualbased
application may have potential benefit to support TB patients
(both literate and illiterate) in their treatment processes.
Abstract: The growth of organic farming practices in the last
few decades is continuing to stimulate the international debate about
this alternative food market. As a part of a PhD project research
about embeddedness in Alternative Food Networks (AFNs), this
paper focuses on the promotional aspects of organic farms websites
from the Madrid region. As a theoretical tool, some knowledge
categories drawn on the geographic studies literature are used to
classify the many ideas expressed in the web pages. By analysing
texts and pictures of 30 websites, the study aims to question how and
to what extent actors from organic world communicate to the
potential customers their personal beliefs about farming practices,
products qualities, and ecological and social benefits. Moreover, the
paper raises the question of whether organic farming laws and
regulations lack of completeness about the social and cultural aspects
of food.
Abstract: SARA is a common and serious metabolic disorder in
early lactation in dairy cattle and in finishing beef cattle, caused by
diets with high inclusion of cereal grain. This experiment was
performed to determine the efficacy of Megasphaera elsdenii, a
major lactate-utilizing bacterium in prevention/treatment of SARA in
vivo. In vivo experimentation, it was used eight ruminally cannulated
rams and it was applied the rapid adaptation with the mixture of grain
based on wheat (80% wheat, 20% barley) and barley (80% barley,
20% wheat). During the systematic adaptation, it was followed the
probability of SARA formation by being measured the rumen pH
with two hours intervals after and before feeding. After being
evaluated the data, it was determined the ruminal pH ranged from
5.2-5.6 on the condition of feeding with 60 percentage of grain
mixture based on barley and wheat, that assured the definite form of
subacute acidosis. In four days SARA period, M. elsdenii (1010 cfu
ml-1) was inoculated during the first two days. During the SARA
period, it was observed the decrease of feed intake with M. elsdenii
inoculation. Inoculation of M. elsdenii was caused to differentiation
of rumen pH (P
Abstract: In this paper a novel color image compression
technique for efficient storage and delivery of data is proposed. The
proposed compression technique started by RGB to YCbCr color
transformation process. Secondly, the canny edge detection method is
used to classify the blocks into the edge and non-edge blocks. Each
color component Y, Cb, and Cr compressed by discrete cosine
transform (DCT) process, quantizing and coding step by step using
adaptive arithmetic coding. Our technique is concerned with the
compression ratio, bits per pixel and peak signal to noise ratio, and
produce better results than JPEG and more recent published schemes
(like CBDCT-CABS and MHC). The provided experimental results
illustrate the proposed technique that is efficient and feasible in terms
of compression ratio, bits per pixel and peak signal to noise ratio.
Abstract: The rapid growth of multimedia technology demands
the secure and efficient access to information. This fast growing lose
the confidence of unauthorized duplication. Henceforth the protection
of multimedia content is becoming more important. Watermarking
solves the issue of unlawful copy of advanced data. In this paper,
blind video watermarking technique has been proposed. A luminance
layer of selected frames is interlaced into two even and odd rows of
an image, further it is deinterlaced and equalizes the coefficients of
the two shares. Color watermark is split into different blocks, and the
pieces of block are concealed in one of the share under the wavelet
transform. Stack the two images into a single image by introducing
interlaced even and odd rows in the two shares. Finally, chrominance
bands are concatenated with the watermarked luminance band. The
safeguard level of the secret information is high, and it is
undetectable. Results show that the quality of the video is not
changed also yields the better PSNR values.
Abstract: This study suggests the estimation method of stress
distribution for the beam structures based on TLS (Terrestrial Laser
Scanning). The main components of method are the creation of the
lattices of raw data from TLS to satisfy the suitable condition and
application of CSSI (Cubic Smoothing Spline Interpolation) for
estimating stress distribution. Estimation of stress distribution for the
structural member or the whole structure is one of the important
factors for safety evaluation of the structure. Existing sensors which
include ESG (Electric strain gauge) and LVDT (Linear Variable
Differential Transformer) can be categorized as contact type sensor
which should be installed on the structural members and also there are
various limitations such as the need of separate space where the
network cables are installed and the difficulty of access for sensor
installation in real buildings. To overcome these problems inherent in
the contact type sensors, TLS system of LiDAR (light detection and
ranging), which can measure the displacement of a target in a long
range without the influence of surrounding environment and also get
the whole shape of the structure, has been applied to the field of
structural health monitoring. The important characteristic of TLS
measuring is a formation of point clouds which has many points
including the local coordinate. Point clouds are not linear distribution
but dispersed shape. Thus, to analyze point clouds, the interpolation is
needed vitally. Through formation of averaged lattices and CSSI for
the raw data, the method which can estimate the displacement of
simple beam was developed. Also, the developed method can be
extended to calculate the strain and finally applicable to estimate a
stress distribution of a structural member. To verify the validity of the
method, the loading test on a simple beam was conducted and TLS
measured it. Through a comparison of the estimated stress and
reference stress, the validity of the method is confirmed.
Abstract: Since 1920, the industry has almost completely
changed the rivets production techniques for the manufacture of
permanent welding join production of structures and manufacture of
other products. The welding arc is the process more widely used in
industries. This is accomplished by the heat of an electric arc which
melts the base metal while the molten metal droplets are transferred
through the arc to the welding pool, protected from the atmosphere
by a gas curtain. The GMAW (Gas metal arc welding) process is
influenced by variables such as: current, polarity, welding speed,
electrode: extension, position, moving direction; type of joint,
welder's ability, among others. It is remarkable that the knowledge
and control of these variables are essential for obtaining satisfactory
quality welds, knowing that are interconnected so that changes in one
of them requiring changes in one or more of the other to produce the
desired results. The optimum values are affected by the type of base
metal, the electrode composition, the welding position and the quality
requirements. Thus, this paper proposes a new methodology, adding
the variable vibration through a mechanism developed for GMAW
welding, in order to improve the mechanical and metallurgical
properties which does not affect the ability of the welder and enables
repeatability of the welds made. For confirmation metallographic
analysis and mechanical tests were made.
Abstract: Brownfields are one of the most important problems
that must be solved by today's cities. The topic of this article is
description of developing a comprehensive transformation of postindustrial
area of the former iron factory national cultural heritage
lower Vítkovice. City of Ostrava used to be industrial superpower of
the Czechoslovak Republic, especially in the area of coal mining and
iron production, after declining industrial production and mining in
the 80s left many unused areas of former factories generally
brownfields and backfields. Since the late 90s we are observing how
the city officials or private entities seeking to remedy this situation.
Regeneration of brownfields is a very expensive and long-term
process. The area is now rebuilt for tourists and residents of the city
in the entertainment, cultural, and social center. It was necessary do
the reconstruction of the industrial monuments. Equally important
was the construction of new buildings, which helped reusing of the
entire complex. This is a unique example of transformation of
technical monuments and completion of necessary new objects, so
that the area could start working again and reintegrate back into the
urban system.
Abstract: This study aims to evaluate the effective size, section
and structural characteristics of circular hollow steel (CHS) damper.
CHS damper is among steel dampers which are used widely for
seismic energy dissipation because they are easy to install, maintain
and are inexpensive. CHS damper dissipates seismic energy through
metallic deformation due to the geometrical elasticity of circular shape
and fatigue resistance around connection part. After calculating the
effective size, which is found to be height to diameter ratio of √3,
nonlinear FE analyses were carried out to evaluate the structural
characteristics and effective section (diameter-to-ratio).
Abstract: In this paper, an experiment was conducted to assess
the impact of online deliberation on citizens’ attitudes. Specifically,
this research compared pre and post deliberation opinions of
participants who deliberated online via an asynchronous platform
regarding the issue of political opinion polls. Results indicate that
online deliberation had a positive effect on citizens’ attitudes since it
was found that following deliberation participants changed their
views regarding public opinion polls. Specifically, online deliberation
improved discussants perceptions regarding the reliability of polls,
while suppressing their negative views about the misuse of polls by
media, polling organizations and politicians.
Abstract: The reduction of phosphorus and sulfur in engine oil
are the main topics of this paper. Very reproducible boundary
lubrication tests were conducted as part of Design of Experiment
software (DOE) to study the behavior of fluorinated catalyst iron
fluoride (FeF3), and polutetrafluoroethylene or Teflon (PTFE) in
developing environmentally friendly (reduced P and S) anti-wear
additives for future engine oil formulations. Multi-component
Chevron fully formulated oil (GF3) and Chevron plain oil were used
with the addition of PTFE and catalyst to characterize and analyze
their performance. Lower phosphorus blends were the goal of the
model solution. Experiments indicated that new sub-micron FeF3
catalyst played an important role in preventing breakdown of the
tribofilm.
Abstract: The main objective of this study was to determine the
effects of Nitrogen fixing bacteria and manure application on the seed
yield and yield components in black cumin (Nigella sativa L.). The
experiment was carried out at the RAN Research Station in
Firouzkouh in 2012. A 4×4 factorial experiment, arranged in a
randomized complete blocks designed with three replications.
Nitrogen fixing bacteria at 4 levels (control, Azotobacter,
Azospirillum and Azotobacter + Azospirillum) and manure
application at 4 levels (0, 2.5, 5 and 7.5 ton ha-1) were used at this
investigation. The present results have shown that the highest height,
1000 seeds weight, seed number per follicle, follicle yield, seed yield
and harvest index were obtained after using Azotobacter and
Azospirillum, simultaneously. Manure application only effects on
follicle yield and by 5ton manure ha-1 the highest follicle yield
obtained. Results of this investigation showed that the maximum seed
yield obtained when Aotobacter+Azospirillum inoculated with black
cumin seeds and 5 ton manure ha-1 applied. According to the results
of this investigation the integrated management of Azotobacter and
Azospirillum with manure application is the best treatment for
achieving the maximum quantitative charactersitics of Black cumin.
Abstract: Si ion implantation was widely used to synthesize
specimens of SiO2 containing supersaturated Si and subsequent high
temperature annealing induces the formation of embedded
luminescent Si nanocrystals. In this work, the potentialities of excimer
UV-light (172 nm, 7.2 eV) irradiation and rapid thermal annealing
(RTA) to enhance the photoluminescence and to achieve low
temperature formation of Si nanocrystals have been investigated. The
Si ions were introduced at acceleration energy of 180 keV to fluence of
7.5 x 1016 ions/cm2. The implanted samples were subsequently
irradiated with an excimer-UV lamp. After the process, the samples
were rapidly thermal annealed before furnace annealing (FA).
Photoluminescence spectra were measured at various stages at the
process. We found that the luminescence intensity is strongly
enhanced with excimer-UV irradiation and RTA. Moreover, effective
visible photoluminescence is found to be observed even after FA at
900 oC, only for specimens treated with excimer-UV lamp and RTA.
We also prepared specimens of Si nanocrystals embedded in a SiO2 by
reactive pulsed laser deposition (PLD) in an oxygen atmosphere. We
will make clear the similarities and differences with the way of
preparation.
Abstract: This paper presents results of compressive strength,
capillary water absorption, and density tests conducted on concrete
containing recycled aggregate (RCA) which is obtained from
structural waste generated by the construction industry in Turkey. In
the experiments, 0%, 15%, 30%, 45% and 60% of the normal
(natural) coarse aggregate was replaced by the recycled aggregate.
Maximum aggregate particle sizes were selected as 16 mm, 22,4 mm
and 31,5 mm; and 0,06%, 0,13% and 0,20% of air-entraining agent
(AEA) were used in mixtures. Fly ash and superplasticizer were used
as a mineral and chemical admixture, respectively. The same type
(CEM I 42.5) and constant dosage of cement were used in the study.
Water/cement ratio was kept constant as 0.53 for all mixture. It was
concluded that capillary water absorption, compressive strength, and
density of concrete decreased with increasing RCA ratio. Increasing
in maximum aggregate particle size and amount of AEA also affect
the properties of concrete significantly.
Abstract: This study investigates the effects of the lead angle
and chip thickness variation on surface roughness during the
machining of compacted graphite iron using ceramic cutting tools
under dry cutting conditions. Analytical models were developed for
predicting the surface roughness values of the specimens after the
face milling process. Experimental data was collected and imported
to the artificial neural network model. A multilayer perceptron model
was used with the back propagation algorithm employing the input
parameters of lead angle, cutting speed and feed rate in connection
with chip thickness. Furthermore, analysis of variance was employed
to determine the effects of the cutting parameters on surface
roughness. Artificial neural network and regression analysis were
used to predict surface roughness. The values thus predicted were
compared with the collected experimental data, and the
corresponding percentage error was computed. Analysis results
revealed that the lead angle is the dominant factor affecting surface
roughness. Experimental results indicated an improvement in the
surface roughness value with decreasing lead angle value from 88° to
45°.