Abstract: Evaluation of crop plants resistance to environmental
stresses specially in germination stage is a critical factor in their
selection in different conditions of cultivation. Therefore use of a
procedure in controllable situation can help to evaluate plants
reaction to stress quickly and precisely. In order to study germination
characteristics of flax in water and salinity stress conditions were
conducted two laboratories experimental. The two experimental were
conducted in 4-replicant completing random design for salinity and
water stress. The treatment, for salinity and water stress was three
potential (zero, 40, 80 mM) of NaCl and three potential (zero, -2, -4
bar) of PEG respectively. Germination percentage and rate, in
addition to Radical and plumule length and dry-weight and
plumule/Radical ration were measured. All of characteristics reduce
under water stress conditions. salinity stress significant reduce
germination rate and Radical and plumule length of flax seeds.
Hydropriming and osmopriming significant increased germination
rate, plumule length and plumule/Radical ration ration of flax seeds.
But germination percentage and Radical and plumule dry weight
significant increased only in hydropriming treat. Hydropriming and
osmopriming could not be used to improved germination under saline
and drought stress. But has more tolerance in salinity and drought
stress in flax by less reduce in Radical and plumule length under
saline and drought stress.
Abstract: Fluid flow in cylinders of elliptic cross-section was investigated. Fluid used is Liquefied petroleum gas (LPG). LPG found in Nigeria contains majorly butane with percentages of propane. Commercial available code FLUENT which uses finite volume method was used to solve fluid flow governing equations. There has been little attention paid to fluid flow in cylindrical elliptic pipes. The present work aims to predict the LPG gas flow in cylindrical pipes of elliptic cross-section. Results of flow parameters of velocity and pressure distributions are presented. Results show that the pressure drop in elliptic pipes is higher than circular pipe of the same cross-sectional area. This is an important result as the pressure drop is related to the pump power needed to drive the flow. Results show that the velocity increases towards centre of the pipe as the flow moves downstream, and also increases towards the outlet of the pipe.
Abstract: This work presents the hydrogen production from
steam gasification of palm kernel shell (PKS) at 700 oC in the
presence of 5% Ni/BEA and 5% Fe/BEA as catalysts. The steam
gasification was performed in two-staged reactors to evaluate the
effect of calcinations temperature and the steam to biomass ratio on
the product gas composition. The catalytic activity of Ni/BEA
catalyst decreases with increasing calcinations temperatures from 500
to 700 oC. The highest H2 concentration is produced by Fe/BEA
(600) with more than 71 vol%. The catalytic activity of the catalysts
tested is found to correspond to its physicochemical properties. The
optimum range for steam to biomass ratio if found to be between 2 to
4. Excess steam content results in temperature drop in the gasifier
which is undesirable for the gasification reactions.
Abstract: This study was conducted to evaluate the effects of
gibberellic acid and 2,4- dichlorophenoxyacetic acid on flower
number, fruit growth and fruit quality of wax apple. GA3 and 2,4-D
were applied at small bud and petal fall stage. Number of flower,
fruit set, fruit drop, fruit crack, fruit growth and fruit quality were
recorded. Results indicated that spraying with 10 ppm GA3 had the
best results in number of flower. GA3 spray at 30 ppm gave the
faster rate of fruit growth than the other treatments. Fruit set, fruit
size as well as fruit weight markedly improved by spraying 30 ppm
GA3, followed by 10 ppm GA3 compared to untreated control.
Moreover, spray GA3 at 30 ppm was the most effective and
increased total soluble solids, reduced titratable acidity and fruit
drop. On the other hand, it was noticed that with 10 ppm 2,4-D
application also enhanced the fruit growth rate, improved
physiological and biochemical characters of fruit compared to
untreated control. It was concluded that both GA3 and 2,4-D spray
have positive effects on fruit development, reduced fruit drop, fruit
crack and improved fruit quality of wax apple under field conditions.
Abstract: Traditional optical networks are gradually evolving towards intelligent optical networks due to the need for faster bandwidth provisioning, protection and restoration of the network that can be accomplished with devices like optical switch, add drop multiplexer and cross connects. Since dense wavelength multiplexing forms the physical layer for intelligent optical networking, the roll of high speed all optical switch is important. This paper analyzes such an ultra-high speed polymer electro-optic switch. The performances of the 2x2 optical waveguide switch with rectangular, triangular and trapezoidal grating profiles on various device parameters are analyzed. The simulation result shows that trapezoidal grating is the optimized structure which has the coupling length of 81μm and switching voltage of 11V for the operating wavelength of 1550nm. The switching time for this proposed switch is 0.47 picosecond. This makes the proposed switch to be an important element in the intelligent optical network.
Abstract: Unlike the best effort service provided by the internet
today, next-generation wireless networks will support real-time
applications. This paper proposes an adaptive early packet discard
(AEPD) policy to improve the performance of the real time TCP
traffic over ATM networks and avoid the fragmentation problem.
Three main aspects are incorporated in the proposed policy. First,
providing quality-of-service (QoS) guaranteed for real-time
applications by implementing a priority scheduling. Second,
resolving the partially corrupted packets problem by differentiating
the buffered cells of one packet from another. Third, adapting a
threshold dynamically using Fuzzy logic based on the traffic
behavior to maintain a high throughput under a variety of load
conditions. The simulation is run for two priority classes of the input
traffic: real time and non-real time classes. Simulation results show
that the proposed AEPD policy improves throughput and fairness
over that using static threshold under the same traffic conditions.
Abstract: The stability characteristics of water lubricated journal bearings having three axial grooves are obtained theoretically. In this lubricant (water) is fed under pressure from one end of the bearing, through the 3-axial grooves (groove angles may vary). These bearings can use the process fluid as the lubricant, as in the case of feed water pumps. The Reynolds equation is solved numerically by the finite difference method satisfying the boundary conditions. The stiffness and damping coefficient for various bearing number and eccentricity ratios, assuming linear pressure drop along the groove, shows that smaller groove angles better results.
Abstract: The present research focus on the processing of mullite-based ceramics from oil refinery industrial wastes and byproducts of agricultural industry and on the investigating of silane modified surface of ceramics. Two waste products were used as initial material – waste aluminum oxide and waste rice husk. The burning - out additives used were waste rise husk. It is known that the oxide ceramics surface is hydrophilic due to the presence of – OH groups in it. The nature of ceramic surface regarding permeation of water and hydrocarbons can be changed by further treatment with silanes. The samples were studied mainly by X-ray analysis, FT-IR absorbance measurements and microscopic analysis. The X-ray analyses showed the phase composition depends on the firing temperature and on the purity of the starting alumina. Two kind of silanes were used for the transformation of surface from hydrophilic to hydrophobic – trimethoxymethylsilane (TMMS) and trimethylclorsilane (TMCS).
Abstract: The prediction of transmembrane helical segments
(TMHs) in membrane proteins is an important field in the
bioinformatics research. In this paper, a method based on discrete
wavelet transform (DWT) has been developed to predict the number
and location of TMHs in membrane proteins. PDB coded as 1F88 was
chosen as an example to describe the prediction of the number and
location of TMHs in membrane proteins by using this method. One
group of test data sets that contain total 19 protein sequences was
utilized to access the effect of this method. Compared with the
prediction results of DAS, PRED-TMR2, SOSUI, HMMTOP2.0 and
TMHMM2.0, the obtained results indicate that the presented method
has higher prediction accuracy.
Abstract: Numerical analysis of flow characteristics and
separation efficiency in a high-efficiency cyclone has been performed.
Several models based on the experimental observation for a design
purpose were proposed. However, the model is only estimated the
cyclone's performance under the limited environments; it is difficult to
obtain a general model for all types of cyclones. The purpose of this
study is to find out the flow characteristics and separation efficiency
numerically. The Reynolds stress model (RSM) was employed instead
of a standard k-ε or a k-ω model which was suitable for isotropic
turbulence and it could predict the pressure drop and the Rankine
vortex very well. For small particles, there were three significant
components (entrance of vortex finder, cone, and dust collector) for
the particle separation. In the present work, the particle re-entraining
phenomenon from the dust collector to the cyclone body was observed
after considerable time. This re-entrainment degraded the separation
efficiency and was one of the significant factors for the separation
efficiency of the cyclone.
Abstract: With the exponentially increasing demand for
wireless communications the capacity of current cellular systems will
soon become incapable of handling the growing traffic. Since radio
frequencies are diminishing natural resources, there seems to be a
fundamental barrier to further capacity increase. The solution can be
found in smart antenna systems.
Smart or adaptive antenna arrays consist of an array of antenna
elements with signal processing capability, that optimize the
radiation and reception of a desired signal, dynamically. Smart
antennas can place nulls in the direction of interferers via adaptive
updating of weights linked to each antenna element. They thus cancel
out most of the co-channel interference resulting in better quality of
reception and lower dropped calls. Smart antennas can also track the
user within a cell via direction of arrival algorithms. This implies that
they are more advantageous than other antenna systems. This paper
focuses on few issues about the smart antennas in mobile radio
networks.
Abstract: This work describes a CACSD tool for automatic design of robust controllers for hydraulic turbines. The tool calculates the optimal controller using the MATLAB hinfopt function and it
serves as a practical and effective solution for the laborious task of
designing a different controller for each type of turbine and generator, and different parameters and conditions of the plant. Results of the simulation of a generating unit subject to parameters
variation show the accuracy and efficiency of the obtained robust
controllers.
Abstract: The effect of a uniform magnetic field on the
formation of drops of specific size has been investigated numerically
in a T-shaped microchannel. Previous researches indicated that the
drop sizes of secondary stream decreases, with increasing main
stream flow rate and decreasing interfacial tension. In the present
study the effect of a uniform magnetic field on the main stream is
considered, and it is proposed that by increasing the Hartmann
number, the size of the drops of the secondary stream will be
decreased.
Abstract: For collecting data from all sensor nodes, some
changes in Dynamic Source Routing (DSR) protocol is proposed. At
each hop level, route-ranking technique is used for distributing
packets to different selected routes dynamically. For calculating rank
of a route, different parameters like: delay, residual energy and
probability of packet loss are used. A hybrid topology of
DMPR(Disjoint Multi Path Routing) and MMPR(Meshed Multi Path
Routing) is formed, where braided topology is used in different
faulty zones of network. For reducing energy consumption, variant
transmission ranges is used instead of fixed transmission range. For
reducing number of packet drop, a fuzzy logic inference scheme is
used to insert different types of delays dynamically. A rule based
system infers membership function strength which is used to
calculate the final delay amount to be inserted into each of the node
at different clusters.
In braided path, a proposed 'Dual Line ACK Link'scheme is
proposed for sending ACK signal from a damaged node or link to a
parent node to ensure that any error in link or any node-failure
message may not be lost anyway. This paper tries to design the
theoretical aspects of a model which may be applied for collecting
data from any large hanging iron structure with the help of wireless
sensor network. But analyzing these data is the subject of material
science and civil structural construction technology, that part is out
of scope of this paper.
Abstract: This paper presents the experimental results on
ageing deterioration of silicone rubber outdoor polymer insulator
under salt water dip wheel test based on IEC 62217. In order to comparison effect of chemical contents, silicone rubber outdoor
polymer insulators having same configuration and leakage distant
from two manufactures were tested together continuously 30,000 test cycles. Many discharge activities were observed in during the test.
After 30,000 test cycles, in spite of same configuration, differences in
degree of surface aging were observed. Physical analysis such as
decreasing in hydrophobicity and increasing in hardness
measurement were measured on two-type tested specimen surface in order to confirm degree of surface ageing. Furthermore, chemical
analysis by ATR-FTIR to diagnose the chemical change of tested
specimen surface was conducted to confirm the physical analysis results.
Abstract: In this work, axisymetric CFD simulation of fixed bed
GTL reactor has been conducted, using computational fluid dynamics
(CFD). In fixed bed CFD modeling, when N (tube-to-particle
diameter ratio) has a large value, it is common to consider the packed
bed as a porous media. Synthesis gas (a mixture of predominantly
carbon monoxide and hydrogen) was fed to the reactor. The reactor
length was 20 cm, divided to three sections. The porous zone was in
the middle section of the reactor. The model equations were solved
employing finite volume method. The effects of particle diameter,
bed voidage, fluid velocity and bed length on pressure drop have
been investigated. Simulation results showed these parameters could
have remarkable impacts on the reactor pressure drop.
Abstract: The gel-supported precipitation (GSP) process can be
used to make spherical particles (spherules) of nuclear fuel,
particularly for very high temperature reactors (VHTR) and even for
implementing the process called SPHEREPAC. In these different
cases, the main characteristics are the sphericity of the particles to be
manufactured and the control over their grain size. Nonetheless,
depending on the specifications defined for these spherical particles,
the GSP process has intrinsic limits, particularly when fabricating
very small particles. This paper describes the use of secondary
fragmentation (water, water/PVA and uranyl nitrate) on solid
surfaces under varying temperature and vibration conditions to assess
the relevance of using this new technique to manufacture very small
spherical particles by means of a modified GSP process. The
fragmentation mechanisms are monitored and analysed, before the
trends for its subsequent optimised application are described.
Abstract: This study focused on arsenate removal by nano
zero-valent iron (NZVI) in the gas-bubbled aqueous solution. It
appears that solution acidified by H2SO4 is far more favorable than by
CO2-bubbled acidification. In addition, as dissolved oxygen was
stripped out of solution by N2 gas bubbling, the arsenate removal
dropped significantly. To take advantages of common practice of
carbonation and oxic condition, pretreatment of CO2 and air bubbling
in sequence are recommended for a better removal of arsenate.
Abstract: The fractal-shaped orifices are assumed to have a
significant effect on the pressure drop downstream pipe flow due to
their edge self-similarity shape which enhances the mixing
properties. Here, we investigate the pressure drop after these fractals
using a digital micro-manometer at different stations downstream a
turbulent flow pipe then a direct comparison has been made with the
pressure drop measured from regular orifices with the same flow
area. Our results showed that the fractal-shaped orifices have a
significant effect on the pressure drop downstream the flow. Also
the pressure drop measured across the fractal-shaped orifices is
noticed to be lower that that from ordinary orifices of the same flow
areas. This result could be important in designing piping systems
from point of view of losses consideration with the same flow
control area. This is promising to use the fractal-shaped orifices as
flowmeters as they can sense the pressure drop across them
accurately with minimum losses than the regular ones.
Abstract: Two-phase frictional pressure drop data were
obtained for condensation of carbon dioxide in single horizontal
micro tube of inner diameter ranged from 0.6 mm up to 1.6 mm over
mass flow rates from 2.5*10-5 to 17*10-5 kg/s and vapor qualities
from 0.0 to 1.0. The inlet condensing pressure is changed from 33.5
to 45 bars. The saturation temperature ranged from -1.5 oC up to 10
oC. These data have then been compared against three (two-phase)
frictional pressure drop prediction methods. The first method is by
Muller-Steinhagen and Heck (Muller-Steinhagen H, Heck K. A
simple friction pressure drop correlation for two-phase flow in pipes.
Chem. Eng. Process 1986;20:297–308) and that by Gronnerud R.
Investigation of liquid hold-up, flow-resistance and heat transfer in
circulation type evaporators, part IV: two-phase flow resistance in
boiling refrigerants, Annexe 1972. Then the method used by
FriedelL. Improved friction pressures drop in horizontal and vertical
two-phase pipe flow. European Two-Phase Flow Group Meeting,
Paper E2; 1979 June, Ispra, Italy. The methods are used by M.B Ould
Didi et al (2001) “Prediction of two-phase pressure gradients of
refrigerant in horizontal tubes". Int.J.of Refrigeration 25(2002) 935-
947. The best available method for annular flow was that of Muller-
Steinhagen and Heck. It was observed that the peak in the two-phase
frictional pressure gradient is at high vapor qualities.