Abstract: Motion response of floating structures is of great
concern in marine engineering. Nonlinearity is an inherent property
of any floating bodies subjected to irregular waves. These floating
structures are continuously subjected to environmental loadings from
wave, current, wind etc. This can result in undesirable motions of the
vessel which may challenge the operability. For a floating body to
remain in its position, it should be able to induce a restoring force
when displaced. Mooring is provided to enable this restoring force.
This paper discusses the hydrodynamic performance and motion
characteristics of an 8 point spread mooring system applied to a pipe
laying barge operating in the West African sea. The modelling of the
barge is done using a computer aided-design (CAD) software
RHINOCEROS. Irregular waves are generated using a suitable wave
spectrum. Both frequency domain and time domain analysis is done.
Numerical simulations based on potential theory are carried out to
find the responses and hydrodynamic performance of the barge in
both free floating as well as moored conditions. Initially, potential
flow frequency domain analysis is done to obtain the Response
Amplitude Operator (RAO) which gives an idea about the structural
motion in free floating state. RAOs for different wave headings are
analyzed. In the following step, a time domain analysis is carried out
to obtain the responses of the structure in the moored condition. In
this study, wave induced motions are only taken into consideration.
Wind and current loads are ruled out and shall be included in further
studies. For the current study, 2000 seconds simulation is taken. The
results represent wave induced motion responses, mooring line
tensions and identify critical mooring lines.
Abstract: We have aimed to produce a self-cleaning transparent
polymer coating with polyurethane (PU) matrix as the latter is highly
solvent, chemical and weather resistant having good mechanical
properties. Nano-silica modified by 1H, 1H, 2H, 2Hperflurooctyltriethoxysilane
was incorporated into the PU matrix for
attaining self-cleaning ability through hydrophobicity. The
modification was confirmed by particle size analysis and scanning
electron microscopy (SEM). Thermo-gravimetric (TGA) studies were
carried to ascertain the grafting of silane onto the silica. Several
coating formulations were prepared by varying the silica loading
content and compared to a commercial equivalent. The effect of
dispersion and the morphology of the coated films were assessed by
SEM analysis. All coating standardized tests like solvent resistance,
adhesion, flexibility, acid, alkali, gloss etc. have been performed as
per ASTM standards. Water contact angle studies were conducted to
analyze the hydrophobic character of the coating. In addition, the
coatings were also subjected to salt spray and accelerated weather
testing to analyze the durability of the coating.
Abstract: The present study investigates the effectiveness of
newly designed clayey pellets (fired clay pellets diameter sizes of 5
and 8 mm, and unfired clay pellets with the diameter size of 15 mm)
as the beds in the column adsorption process. The adsorption
experiments in the batch mode were performed before the column
experiment with the purpose to determine the order of adsorbent
package in the column which was to be designed in the investigation.
The column experiment was performed by using a known mass of the
clayey beds and the volume of the waste printing developer, which
was purified. The column was filled in the following order: fired clay
pellets of the diameter size of 5 mm, fired clay pellets of the diameter
size of 8 mm, and unfired clay pellets of the diameter size of 15 mm.
The selected order of the adsorbents showed a high removal
efficiency for zinc (97.8%) and copper (81.5%) ions. These
efficiencies were better than those in the case of the already existing
mode adsorption. The obtained experimental data present a good
basis for the selection of an appropriate column fill, but further
testing is necessary in order to obtain more accurate results.
Abstract: Myoelectric control system is the fundamental
component of modern prostheses, which uses the myoelectric signals
from an individual’s muscles to control the prosthesis movements.
The surface electromyogram signal (sEMG) being noninvasive has
been used as an input to prostheses controllers for many years.
Recent technological advances has led to the development of
implantable myoelectric sensors which enable the internal
myoelectric signal (MES) to be used as input to these prostheses
controllers. The intramuscular measurement can provide focal
recordings from deep muscles of the forearm and independent signals
relatively free of crosstalk thus allowing for more independent
control sites. However, little work has been done to compare the two
inputs. In this paper we have compared the classification accuracy of
six pattern recognition based myoelectric controllers which use
surface myoelectric signals recorded using untargeted (symmetric)
surface electrode arrays to the same controllers with multichannel
intramuscular myolectric signals from targeted intramuscular
electrodes as inputs. There was no significant enhancement in the
classification accuracy as a result of using the intramuscular EMG
measurement technique when compared to the results acquired using
the surface EMG measurement technique. Impressive classification
accuracy (99%) could be achieved by optimally selecting only five
channels of surface EMG.
Abstract: The present study aims to explore the effect of
computerization on marketing performance in Snowa Company. In
other words, this study intends to respond to this question that
whether or not, is there any relationship between utilization of
computerization in marketing activities and marketing performance?
The statistical population included 60 marketing managers of Snowa
Company. In order to test the research hypotheses, Pearson
correlation coefficient was employed. The reliability was equal to
96.8%. In this study, computerization was the independent variable
and marketing performance was the dependent variable with
characteristics of market share, improving the competitive position,
and sales volume. The results of testing the hypotheses revealed that
there is a significant relationship between utilization of
computerization and market share, sales volume and improving the
competitive position.
Abstract: The rheological response of blends obtained from
quaternized polysulfone and polyvinyl alcohol in N-methyl-2-
pyrrolidone as against structural peculiarity of polymers from the
blend, composition of polymer mixtures, as well as the types of
interactions were investigated. Results show that the variation of
polyvinyl alcohol composition in the studied system determines
changes of the rheological properties, suggesting that the PVA acts as
a plasticizer. Consequently, rheological behavior of complex system,
described by the nonlinear flow curve, indicates the impact of
polyvinil alcohol content to polysulfone solution, in order to facilitate
the subsequently preparation of bioactive membranes.
Abstract: A 15-storey RC building, studied in this paper, is
representative of modern building type constructed in Madina City in
Saudi Arabia before 10 years ago. These buildings are almost
consisting of reinforced concrete skeleton i.e. columns, beams and
flat slab as well as shear walls in the stairs and elevator areas
arranged in the way to have a resistance system for lateral loads
(wind – earthquake loads). In this study, the dynamic properties of
the 15-storey RC building were identified using ambient motions
recorded at several, spatially-distributed locations within each
building. Three dimensional pushover analysis (Nonlinear static
analysis) was carried out using SAP2000 software incorporating
inelastic material properties for concrete, infill and steel. The effect
of modeling the building with and without infill walls, on the
performance point as well as capacity and demand spectra due to EQ
design spectrum function in Madina area has been investigated. ATC-
40 capacity and demand spectra are utilized to get the modification
factor (R) for the studied building. The purpose of this analysis is to
evaluate the expected performance of structural systems by
estimating, strength and deformation demands in design, and
comparing these demands to available capacities at the performance
levels of interest. The results are summarized and discussed.
Abstract: Orthogonal Frequency Division Multiplexing
(OFDM) has been used in many advanced wireless communication
systems due to its high spectral efficiency and robustness to
frequency selective fading channels. However, the major concern
with OFDM system is the high peak-to-average power ratio (PAPR)
of the transmitted signal. Some of the popular techniques used for
PAPR reduction in OFDM system are conventional partial transmit
sequences (CPTS) and clipping. In this paper, a parallel
combination/hybrid scheme of PAPR reduction using clipping and
CPTS algorithms is proposed. The proposed method intelligently
applies both the algorithms in order to reduce both PAPR as well as
computational complexity. The proposed scheme slightly degrades
bit error rate (BER) performance due to clipping operation and it can
be reduced by selecting an appropriate value of the clipping ratio
(CR). The simulation results show that the proposed algorithm
achieves significant PAPR reduction with much reduced
computational complexity.
Abstract: An Energetic and exergetic analysis is conducted on a
Steam Turbine Power Plant of an existing Phosphoric Acid Factory.
The heat recovery systems used in different parts of the plant are also
considered in the analysis. Mass, thermal and exergy balances are
established on the main compounds of the factory. A numerical code
is established using EES software to perform the calculations
required for the thermal and exergy plant analysis. The effects of the
key operating parameters such as steam pressure and temperature,
mass flow rate as well as seawater temperature, on the cycle
performances are investigated. A maximum Exergy Loss Rate of about 72% is obtained for the
melters, followed by the condensers, heat exchangers and the pumps.
The heat exchangers used in the phosphoric acid unit present
exergetic efficiencies around 33% while 60% to 72% are obtained for
steam turbines and blower. For the explored ranges of HP steam
temperature and pressure, the exergy efficiencies of steam turbine
generators STGI and STGII increase of about 2.5% and 5.4%
respectively. In the same way optimum HP steam flow rate values,
leading to the maximum exergy efficiencies are defined.
Abstract: Teaching of mathematics to engineering students is an
open ended problem in education. The main goal of mathematics
learning for engineering students is the ability of applying a wide
range of mathematical techniques and skills in their engineering
classes and later in their professional work. Most of the
undergraduate engineering students and faculties feels that no efforts
and attempts are made to demonstrate the applicability of various
topics of mathematics that are taught thus making mathematics
unavoidable for some engineering faculty and their students. The lack
of understanding of concepts in engineering mathematics may hinder
the understanding of other concepts or even subjects. However, for
most undergraduate engineering students, mathematics is one of the
most difficult courses in their field of study. Most of the engineering students never understood mathematics or
they never liked it because it was too abstract for them and they could
never relate to it. A right balance of application and concept based
teaching can only fulfill the objectives of teaching mathematics to
engineering students. It will surely improve and enhance their
problem solving and creative thinking skills. In this paper, some practical (informal) ways of making
mathematics-teaching application based for the engineering students
is discussed. An attempt is made to understand the present state of
teaching mathematics in engineering colleges. The weaknesses and
strengths of the current teaching approach are elaborated. Some of
the causes of unpopularity of mathematics subject are analyzed and a
few pragmatic suggestions have been made. Faculty in mathematics
courses should spend more time discussing the applications as well as
the conceptual underpinnings rather than focus solely on strategies
and techniques to solve problems. They should also introduce more
‘word’ problems as these problems are commonly encountered in
engineering courses. Overspecialization in engineering education
should not occur at the expense of (or by diluting) mathematics and
basic sciences. The role of engineering education is to provide the
fundamental (basic) knowledge and to teach the students simple
methodology of self-learning and self-development. All these issues
would be better addressed if mathematics and engineering faculty
join hands together to plan and design the learning experiences for
the students who take their classes. When faculties stop competing
against each other and start competing against the situation, they will
perform better. Without creating any administrative hassles these
suggestions can be used by any young inexperienced faculty of
mathematics to inspire engineering students to learn engineering
mathematics effectively.
Abstract: Concrete is an essential building material which is
widely used in construction industry all over the world due to its
compressible strength. Curing of concrete plays a vital role in
durability and other performance necessities. Improper curing can
affect the concrete performance and durability easily. When areas
like scarcity of water, structures is not accessible by humans external
curing cannot be performed, so we opt for internal curing. Internal
curing (or) self curing plays a major role in developing the concrete
pore structure and microstructure. The concept of internal curing is to
enhance the hydration process to maintain the temperature uniformly.
The evaporation of water in the concrete is reduced by self curing
agent (Super Absorbing Polymer – SAP) there by increasing the
water retention capacity of the concrete. The research work was
carried out to reduce water, which is prime material used for concrete
in the construction industry. Concrete curing plays a major role in
developing hydration process. Concept of self curing will reduce the
evaporation of water from concrete. Self curing will increase water
retention capacity as compared to the conventional concrete. Proper
self curing (or) internal curing increases the strength, durability and
performance of concrete. Super absorbing Polymer (SAP) used as
internal curing agent. In this study 0.2% to 0.4% of SAP was varied
in different grade of high strength concrete. In the experiment
replacement of cement by silica fumes with 5%, 10% and 15% are
studied. It is found that replacement of silica fumes by 10 % gives
more strength and durability when compared to others.
Abstract: In this current contribution, authors are dedicated to
investigate influence of the crystal lamellae orientation on
electromechanical behaviors of relaxor ferroelectric Poly
(vinylidene fluoride –trifluoroethylene -chlorotrifluoroethylene)
(P(VDF-TrFE-CTFE)) films by control of polymer microstructure,
aiming to picture the full map of structure-property relationship. In
order to define their crystal orientation films, terpolymer films were
fabricated by solution-casting, stretching and hot-pressing process.
Differential scanning calorimetry, impedance analyzer, and tensile
strength techniques were employed to characterize crystallographic
parameters, dielectric permittivity, and elastic Young’s modulus
respectively. In addition, large electrical induced out-of-plane
electrostrictive strain was obtained by cantilever beam mode.
Consequently, as-casted pristine films exhibited surprisingly high
electrostrictive strain 0.1774% due to considerably small value of
elastic Young’s modulus although relatively low dielectric
permittivity. Such reasons contributed to large mechanical elastic
energy density. Instead, due to 2 folds increase of elastic Young’s
modulus and less than 50% augmentation of dielectric constant, fullycrystallized
film showed weak electrostrictive behavior and
mechanical energy density as well. And subjected to mechanical
stretching process, Film C exhibited stronger dielectric constant and
out-performed electrostrictive strain over Film B because edge-on
crystal lamellae orientation induced by uniaxially mechanical stretch.
Hot-press films were compared in term of cooling rate. Rather large
electrostrictive strain of 0.2788% for hot-pressed Film D in
quenching process was observed although its dielectric permittivity
equivalent to that of pristine as-casted Film A, showing highest
mechanical elastic energy density value of 359.5 J/m3. In hot-press
cooling process, dielectric permittivity of Film E saw values at 48.8
concomitant with ca.100% increase of Young’s modulus. Films with
intermediate mechanical energy density were obtained.
Abstract: The crossover probability and mutation probability are the two important factors in genetic algorithm. The adaptive genetic algorithm can improve the convergence performance of genetic algorithm, in which the crossover probability and mutation probability are adaptively designed with the changes of fitness value. We apply adaptive genetic algorithm into a function optimization problem. The numerical experiment represents that adaptive genetic algorithm improves the convergence speed and avoids local convergence.
Abstract: Excessive vibration means increased wear, increased
repair efforts, bad product selection & quality and high energy
consumption. This may be sometimes experienced by cavitation or
suction/discharge recirculation which could occur only when net
positive suction head available NPSHA drops below the net positive
suction head required NPSHR. Cavitation can cause axial surging, if it
is excessive, will damage mechanical seals, bearings, possibly other
pump components frequently, and shorten the life of the impeller.
Efforts have been made to explain Suction Energy (SE), Specific
Speed (Ns), Suction Specific Speed (Nss), NPSHA, NPSHR & their
significance, possible reasons of cavitation /internal recirculation, its
diagnostics and remedial measures to arrest and prevent cavitation in
this paper. A case study is presented by the author highlighting that
the root cause of unwanted noise and vibration is due to cavitation,
caused by high specific speeds or inadequate net- positive suction
head available which results in damages to material surfaces of
impeller & suction bells and degradation of machine performance, its
capacity and efficiency too. Author strongly recommends revisiting
the technical specifications of CW pumps to provide sufficient NPSH
margin ratios >1.5, for future projects and Nss be limited to 8500 -
9000 for cavitation free operation.
Abstract: Nanotechnology in pristine sense refers to building of
structures at atomic and molecular scale. Meticulously
nanotechnology encompasses the nanomaterials with at least one
dimension size ranging from 1 to 100 nanometres. Unlike the literal
meaning of its name, nanotechnology is a massive concept beyond
imagination. This paper predominantly deals with relevance of
nanotechnology in automotive industries. New generation of
automotives looks at nanotechnology as an emerging trend of
manufacturing revolution. Intricate shapes can be made out of fairly
inexpensive raw materials instead of conventional fabrication
process. Though the current era have enough technology to face
competition, nanotechnology can give futuristic implications to pick
up the modern pace. Nanotechnology intends to bridge the gap
between automotives with superior technical performance and their
cost fluctuation. Preliminarily, it is an area of great scientific interest
and a major shaper of many new technologies. Nanotechnology can
be an ideal building block for automotive industries, under constant
evolution offering a very wide scope of activity. It possesses huge
potential and is still in the embryonic form of research and
development.
Abstract: Energy has a prominent role for development of
nations. Countries which have energy resources also have strategic
power in the international trade of energy since it is essential for all
stages of production in the economy. Thus, it is important for
countries to analyze the weaknesses and strength of the system. On
the other side, international trade is one of the fields that are analyzed
as a complex network via network analysis. Complex network is one
of the tools to analyze complex systems with heterogeneous agents
and interaction between them. A complex network consists of nodes
and the interactions between these nodes. Total properties which
emerge as a result of these interactions are distinct from the sum of
small parts (more or less) in complex systems. Thus, standard
approaches to international trade are superficial to analyze these
systems. Network analysis provides a new approach to analyze
international trade as a network. In this network, countries constitute
nodes and trade relations (export or import) constitute edges. It
becomes possible to analyze international trade network in terms of
high degree indicators which are specific to complex networks such
as connectivity, clustering, assortativity/disassortativity, centrality,
etc. In this analysis, international trade of crude oil and coal which
are types of fossil fuel has been analyzed from 2005 to 2014 via
network analysis. First, it has been analyzed in terms of some
topological parameters such as density, transitivity, clustering etc.
Afterwards, fitness to Pareto distribution has been analyzed via
Kolmogorov-Smirnov test. Finally, weighted HITS algorithm has
been applied to the data as a centrality measure to determine the real
prominence of countries in these trade networks. Weighted HITS
algorithm is a strong tool to analyze the network by ranking countries
with regards to prominence of their trade partners. We have
calculated both an export centrality and an import centrality by
applying w-HITS algorithm to the data. As a result, impacts of the
trading countries have been presented in terms of high-degree
indicators.
Abstract: In order to retrieve images efficiently from a large
database, a unique method integrating color and texture features
using genetic programming has been proposed. Opponent color
histogram which gives shadow, shade, and light intensity invariant
property is employed in the proposed framework for extracting color
features. For texture feature extraction, fast discrete curvelet
transform which captures more orientation information at different
scales is incorporated to represent curved like edges. The recent
scenario in the issues of image retrieval is to reduce the semantic gap
between user’s preference and low level features. To address this
concern, genetic algorithm combined with relevance feedback is
embedded to reduce semantic gap and retrieve user’s preference
images. Extensive and comparative experiments have been conducted
to evaluate proposed framework for content based image retrieval on
two databases, i.e., COIL-100 and Corel-1000. Experimental results
clearly show that the proposed system surpassed other existing
systems in terms of precision and recall. The proposed work achieves
highest performance with average precision of 88.2% on COIL-100
and 76.3% on Corel, the average recall of 69.9% on COIL and 76.3%
on Corel. Thus, the experimental results confirm that the proposed
content based image retrieval system architecture attains better
solution for image retrieval.
Abstract: Nanofibers are defined as fibers with diameters less
than 100 nanometers. In this study, behaviours of activated carbon
nanofiber (ACNF), carbon nanofiber (CNF), polyacrylonitrile/ carbon
nanotube (PAN/CNT), polyvinyl alcohol/nanosilver (PVA/Ag) in
proton exchange membrane (PEM) fuel cells are investigated
experimentally. This material was used as gas diffusion layer (GDL)
in PEM fuel cells. In this study, the electrical conductivities of
nanofiber and nanofiber/nanoparticles have been studied to
understand their effects on PEM fuel cell performance. According to
the experimental results, the maximum electrical conductivity
performance of the fuel cell with nanofiber was found to be at
PVA/Ag (at UConn condition). The electrical conductivities of CNF,
ACNF, PAN/CNT are lower for PEM. The resistance of cell with
PVA/Ag is lower than the resistance of cell with PAN/CNT, ACNF,
CNF.
Abstract: The study of the aerodynamics related to the
improvement in the acting of airplanes and automobiles with the
objective of being reduced the effect of the attrition of the air on
structures, providing larger speeds and smaller consumption of fuel.
The application of the knowledge of the aerodynamics not more
limits to the aeronautical and automobile industries. Therefore, this
research aims to design and construction of a wind tunnel to perform
aerodynamic analysis in bodies of cars, seeking greater efficiency.
Therefore, this research aims to design and construction of a wind
tunnel to perform aerodynamic analysis in bodies of cars, seeking
greater efficiency. For this, a methodology for wind tunnel type
selection is designed to be built, taking into account the various
existing configurations in which chose to build an open circuit tunnel,
due to the lower complexity of construction and installation;
operational simplicity and low cost. The guidelines for the project
were teaching: the layer that limits study and analyze specimens with
different geometries. For the variation of pressure in the test, section
of a switched gauge used a pitot tube. Thus, it was possible to obtain
quantitative and qualitative results, which proved to be satisfactory.
Abstract: Biodiesel is widely investigated to solve the twin
problem of depletion of fossil fuel and environmental degradation.
The main objective of the present work is to compare performance,
emissions, and combustion characteristics of biodiesel derived from
cotton seed oil in a diesel engine with the baseline results of
petrodiesel fuel. Tests have been conducted on a single cylinder, four
stroke CIDI diesel engine with a speed of 1500 rpm and a fixed
compression ratio of 17.5 at different load conditions. The
performance parameters evaluated include brake thermal efficiency,
brake specific fuel consumption, brake power, indicated mean
effective pressure, mechanical efficiency, and exhaust gas
temperature. Regarding combustion study, cylinder pressure, rate of
pressure rise, net heat release rate, cumulative heat release, mean gas
temperature, mass fraction burned, and fuel line pressure were
evaluated. The emission parameters such as carbon monoxide, carbon
dioxide, un-burnt hydrocarbon, oxides of nitrogen, and smoke
opacity were also measured by a smoke meter and an exhaust gas
analyzer and compared with baseline results. The brake thermal
efficiency of cotton seed oil methyl ester (CSOME) was lower than
that of petrodiesel and brake specific fuel consumption was found to
be higher. However, biodiesel resulted in the reduction of carbon
dioxide, un-burnt hydrocarbon, and smoke opacity at the expense of
nitrogen oxides. Carbon monoxide emissions for biodiesel was higher
at maximum output power. It has been found that the combustion
characteristics of cotton seed oil methyl ester closely followed those
of standard petrodiesel. The experimental results suggested that
biodiesel derived from cotton seed oil could be used as a good
substitute to petrodiesel fuel in a conventional diesel without any
modification.