Abstract: This paper presents the experimental results of 11 kV
and 33 kV silicon composite insulators under artificial salt and urea
polluted conditions. The tests were carried out under different
seasons like summer, winter, and monsoon. The artificial pollution is
prepared by properly dissolving the salt and urea in the water. The
prepared salt and urea pollutions are sprayed on the insulators and
dried up for sufficiently large time. The process is continued until a
uniform layer is formed on the surface of insulator. For each insulator
rating, four samples were tested. The maximum leakage current and
breakdown voltage were measured. From experimental data,
performance of test specimen is evaluated by comparing breakdown
voltage and leakage current during different seasons when exposed to
salt and urea polluted conditions. From these results the performance
of the insulators can be predicted when they are installed in
industrial, agricultural, and coastal areas. The experimental tests were
carried out in the High Voltage laboratory using two stage cascade
transformer having the rating of 1000 kVA, 500 kV.
Abstract: The field of instrumentation electronics is undergoing
an explosive growth, due to its wide range of applications. The
proliferation of electrical devices in a close working proximity can
negatively influence each other’s performance. The degradation in
the performance is due to electromagnetic interference (EMI). This paper investigates the negative effects of electromagnetic
interference originating in the General Purpose Interface Bus (GPIB)
control-network of the AC-DC transfer measurement system.
Remedial measures of reducing measurement errors and failure of
range of industrial devices due to EMI have been explored. The ACDC
transfer measurement system was analysed for the commonmode
(CM) EMI effects. Further investigation of coupling path as
well as much accurate identification of noise propagation mechanism
has been outlined. To prevent the occurrence of common-mode
(ground loops) which was identified between the GPIB system
control circuit and the measurement circuit, a microcontroller-driven
GPIB switching isolator device was designed, prototyped,
programmed and validated. This mitigation technique has been
explored to reduce EMI effectively.
Abstract: The focus of this study was to determine the factors associated with the use of substances for sport performance of youth in Lagos state sport. Questionnaire was the instrument used for the study. Descriptive research method was used. The estimated population for the study was 2000 sport men and women. The sample size was 200 respondents for purposive sampling techniques were used. The instrument was validated in it content and constructs value. The instrument was administered with the assistance of the coaches. Same 200 copies administered were returned. The data obtained was analysed using simple percentage and chi-square (x2) for stated hypothesis at 0.05 level of significance. The finding reveal that sport injuries exercise induced and anaphylaxis and asthma and feeling of loss of efficacy associated with alcohol used on sport performance among the users of substances. Alcohol users are recommended to partake in sport like swimming, basketball and volleyball because they have space of time for resting while at play. Government should be fully in charge of the health of sport men and women.
Abstract: In this paper, an Infinite Impulse Response (IIR) filter
has been designed and simulated on an Field Programmable Gate
Arrays (FPGA). The implementation is based on Multiply Add and
Accumulate (MAC) algorithm which uses multiply operations for
design implementation. Parallel Pipelined structure is used to
implement the proposed IIR Filter taking optimal advantage of the
look up table of target device. The designed filter has been
synthesized on Digital Signal Processor (DSP) slice based FPGA to
perform multiplier function of MAC unit. The DSP slices are useful
to enhance the speed performance. The proposed design is simulated
with Matlab, synthesized with Xilinx Synthesis Tool, and
implemented on FPGA devices. The Virtex 5 FPGA based design can
operate at an estimated frequency of 81.5 MHz as compared to 40.5
MHz in case of Spartan 3 ADSP based design. The Virtex 5 based
implementation also consumes less slices and slice flip flops of target
FPGA in comparison to Spartan 3 ADSP based implementation to
provide cost effective solution for signal processing applications.
Abstract: Banda Sea Collision Zone (BSCZ) is the result of the
interaction and convergence of Indo-Australian plate, Eurasian plate
and Pacific plate. This location is located in eastern Indonesia. This
zone has a very high seismic activity. In this research, we will
calculate the rate (λ) and Mean Square Error (MSE). By this result,
we will classification earthquakes distribution in the BSCZ with the
point process approach. Chi-square is used to determine the type of
earthquakes distribution in the sub region of BSCZ. The data used in
this research is data of earthquakes with a magnitude ≥ 6 SR for the
period 1964-2013 and sourced from BMKG Jakarta. This research is
expected to contribute to the Moluccas Province and surrounding
local governments in performing spatial plan document related to
disaster management.
Abstract: Dietary cholesterol has elicited the most public
interest as it relates with coronary heart disease. Thus, humans have
been paying more attention to health, thereby reducing consumption
of cholesterol enriched food. Egg is considered as one of the major
sources of human dietary cholesterol. However, an alternative way to
reduce the potential cholesterolemic effect of eggs is to modify the
fatty acid composition of the yolk. The effect of palm oil (PO),
soybean oil (SO), sesame seed oil (SSO) and fish oil (FO)
supplementation in the diets of layers on egg yolk fatty acid,
cholesterol, egg production and egg quality parameters were
evaluated in a 42-day feeding trial. One hundred and five Isa Brown
laying hens of 34 weeks of age were randomly distributed into seven
groups of five replicates and three birds per replicate in a completely
randomized design. Seven corn-soybean basal diets (BD) were
formulated: BD+No oil (T1), BD+1.5% PO (T2), BD+1.5% SO (T3),
BD+1.5% SSO (T4), BD+1.5% FO (T5), BD+0.75% SO+0.75% FO
(T6) and BD+0.75% SSO+0.75% FO (T7). Five eggs were randomly
sampled at day 42 from each replicate to assay for the cholesterol,
fatty acid profile of egg yolk and egg quality assessment. Results
showed that there were no significant (P>0.05) differences observed
in production performance, egg cholesterol and egg quality
parameters except for yolk height, albumen height, yolk index, egg
shape index, haugh unit, and yolk colour. There were no significant
differences (P>0.05) observed in total cholesterol, high density
lipoprotein and low density lipoprotein levels of egg yolk across the
treatments. However, diets had effect (P
Abstract: The number and adequacy of Performance-Indicators
(PIs) for organisational purposes are core to the success of
organisations and a major concern to the sponsor of this research.
This assignment developed a procedure to improve a firm’s
performance assessment system, by identifying two key-PIs out of 28
initial ones, and by setting criteria and their relative importance to
validate and rank the adequacy and the right number of operational
metrics. The Analytical-Hierarchy-Process was used with a synthesismethod
to treat data coming from the management inquiries.
Although organisational alignment has been achieved, business
processes should also be targeted and PIs continuously revised.
Abstract: In this corporate world, the technology of Web
services has grown rapidly and its significance for the development
of web based applications gradually rises over time. The success of
Business to Business integration rely on finding novel partners and
their services in a global business environment. However, the
selection of the most suitable Web service from the list of services
with the identical functionality is more vital. The satisfaction level of
the customer and the provider’s reputation of the Web service are
primarily depending on the range it reaches the customer’s
requirements. In most cases, the customer of the Web service feels
that he is spending for the service which is undelivered. This is
because the customer always thinks that the real functionality of the
web service is not reached. This will lead to change of the service
frequently. In this paper, a framework is proposed to evaluate the
Quality of Service (QoS) and its cost that makes the optimal
correlation between each other. In addition, this research work
proposes some management decision against the functional deviancy
of the web service that is guaranteed at time of selection.
Abstract: The overall goal of this paper is to examine the
suitability and potential of the policies addressing the sustainability
and affordability of housing for returnees, and to determine the impact
of this policy on housing delivery for Afghan refugees. Housing is a
central component of the settlement experience of refugees. A positive
housing situation can facilitate many aspects of integration.
Unaffordable, and unsafe housing, however, can cause disruptions in
the entire settlement process. This paper aims to identify a suite of
built forms for housing that is both affordable and environmentally
sustainable for Afghan refugees. The result was the development of a
framework that enables the assessment of the overall performance of
various types of housing development in all zones of the country.
There is very little evidence that the present approach of housing
provision to the vagaries of market forces has provided affordable
housing, especially for Afghan refugees. There is a need to incorporate
social housing into the policy to assist people who cannot afford to
have their own houses.
Abstract: Advances in spatial and spectral resolution of satellite
images have led to tremendous growth in large image databases. The
data we acquire through satellites, radars, and sensors consists of
important geographical information that can be used for remote
sensing applications such as region planning, disaster management.
Spatial data classification and object recognition are important tasks
for many applications. However, classifying objects and identifying
them manually from images is a difficult task. Object recognition is
often considered as a classification problem, this task can be
performed using machine-learning techniques. Despite of many
machine-learning algorithms, the classification is done using
supervised classifiers such as Support Vector Machines (SVM) as the
area of interest is known. We proposed a classification method,
which considers neighboring pixels in a region for feature extraction
and it evaluates classifications precisely according to neighboring
classes for semantic interpretation of region of interest (ROI). A
dataset has been created for training and testing purpose; we
generated the attributes by considering pixel intensity values and
mean values of reflectance. We demonstrated the benefits of using
knowledge discovery and data-mining techniques, which can be on
image data for accurate information extraction and classification from
high spatial resolution remote sensing imagery.
Abstract: There was a scenario present day that drying of fresh
fruits and vegetables by indirect solar drying by using mechanical
device; hence, an effort was made to develop a small scale solar
tunnel dryer (STD). Drying of spinach is carried out to analyze the
performance of the dryer and to study its drying characteristics. To
evaluate the performance of dryer the independent variables were
selected as air flow rate, loading density and shade net while collector
efficiency, drying efficiency, overall efficiency and specific energy
consumption were selected as responses during performing the
experiments. The spinach was dried from initial moisture content
88.21-94.04% (w.b.) to final moisture content 3.50-5.13% (w.b.). The
drying time considerably reduced as compared to open sun drying of
spinach as sun drying took 15 h for drying. The average collector
efficiency, drying efficiency and overall efficiency were in the range
28.73-61.15%, 11.63% to 22.13%, and 7.61-14.66%, respectively.
Abstract: This paper investigates the characteristics of wall
pressure fluctuations in naturally developing boundary layer flows
on axisymmetric bodies experimentally. The axisymmetric body has
a modified ellipsoidal blunt nose. Flush-mounted microphones are
used to measure the wall pressure fluctuations in the boundary layer
flow over the body. The measurements are performed in a low noise
wind tunnel. It is found that the correlation between the flow regime
and the characteristics of the pressure fluctuations is distinct. The
process from small fluctuation in laminar flow to large fluctuation in
turbulent flow is investigated. Tollmien-Schlichting wave (T-S wave)
is found to generate and develop in transition. Because of the T-S
wave, the wall pressure fluctuations in the transition region are higher
than those in the turbulent boundary layer.
Abstract: Segmentation of left ventricle (LV) from cardiac
ultrasound images provides a quantitative functional analysis of the
heart to diagnose disease. Active Shape Model (ASM) is widely used
for LV segmentation, but it suffers from the drawback that
initialization of the shape model is not sufficiently close to the target,
especially when dealing with abnormal shapes in disease. In this work,
a two-step framework is improved to achieve a fast and efficient LV
segmentation. First, a robust and efficient detection based on Hough
forest localizes cardiac feature points. Such feature points are used to
predict the initial fitting of the LV shape model. Second, ASM is
applied to further fit the LV shape model to the cardiac ultrasound
image. With the robust initialization, ASM is able to achieve more
accurate segmentation. The performance of the proposed method is
evaluated on a dataset of 810 cardiac ultrasound images that are mostly
abnormal shapes. This proposed method is compared with several
combinations of ASM and existing initialization methods. Our
experiment results demonstrate that accuracy of the proposed method
for feature point detection for initialization was 40% higher than the
existing methods. Moreover, the proposed method significantly
reduces the number of necessary ASM fitting loops and thus speeds up
the whole segmentation process. Therefore, the proposed method is
able to achieve more accurate and efficient segmentation results and is
applicable to unusual shapes of heart with cardiac diseases, such as left
atrial enlargement.
Abstract: Digital images are widely used in computer
applications. To store or transmit the uncompressed images
requires considerable storage capacity and transmission bandwidth.
Image compression is a means to perform transmission or storage of
visual data in the most economical way. This paper explains about
how images can be encoded to be transmitted in a multiplexing
time-frequency domain channel. Multiplexing involves packing
signals together whose representations are compact in the working
domain. In order to optimize transmission resources each 4 × 4
pixel block of the image is transformed by a suitable polynomial
approximation, into a minimal number of coefficients. Less than
4 × 4 coefficients in one block spares a significant amount of
transmitted information, but some information is lost. Different
approximations for image transformation have been evaluated as
polynomial representation (Vandermonde matrix), least squares +
gradient descent, 1-D Chebyshev polynomials, 2-D Chebyshev
polynomials or singular value decomposition (SVD). Results have
been compared in terms of nominal compression rate (NCR),
compression ratio (CR) and peak signal-to-noise ratio (PSNR)
in order to minimize the error function defined as the difference
between the original pixel gray levels and the approximated
polynomial output. Polynomial coefficients have been later encoded
and handled for generating chirps in a target rate of about two
chirps per 4 × 4 pixel block and then submitted to a transmission
multiplexing operation in the time-frequency domain.
Abstract: The aim of this study is to examine, through
experimentation in the laboratory, the supercritical flow in the
presence of an obstacle in a rectangular channel. The supercritical
regime in the whole hydraulic channel is achieved by adding a
convergent. We will observe the influence of the obstacle shape and
dimension on the characteristics of the supercritical flow, mainly the
free-surface elevation and the velocity profile. The velocity
measurements have been conducted with the one dimension laser
anemometry technique.
Abstract: Journal bearings used in IC engines are prone to premature
failures and are likely to fail earlier than the rated life due to
highly impulsive and unstable operating conditions and frequent
starts/stops. Vibration signature extraction and wear debris analysis
techniques are prevalent in industry for condition monitoring of
rotary machinery. However, both techniques involve a great deal of
technical expertise, time, and cost. Limited literature is available on
the application of these techniques for fault detection in reciprocating
machinery, due to the complex nature of impact forces that
confounds the extraction of fault signals for vibration-based analysis
and wear prediction. In present study, a simulation model was developed to investigate
the bearing wear behaviour, resulting because of different operating
conditions, to complement the vibration analysis. In current
simulation, the dynamics of the engine was established first, based on
which the hydrodynamic journal bearing forces were evaluated by
numerical solution of the Reynold’s equation. In addition, the
essential outputs of interest in this study, critical to determine wear
rates are the tangential velocity and oil film thickness between the
journals and bearing sleeve, which if not maintained appropriately,
have a detrimental effect on the bearing performance. Archard’s wear prediction model was used in the simulation to
calculate the wear rate of bearings with specific location information
as all determinative parameters were obtained with reference to crank
rotation. Oil film thickness obtained from the model was used as a
criterion to determine if the lubrication is sufficient to prevent contact
between the journal and bearing thus causing accelerated wear. A
limiting value of 1 μm was used as the minimum oil film thickness
needed to prevent contact. The increased wear rate with growing
severity of operating conditions is analogous and comparable to the
rise in amplitude of the squared envelope of the referenced vibration
signals. Thus on one hand, the developed model demonstrated its
capability to explain wear behaviour and on the other hand it also
helps to establish a co-relation between wear based and vibration
based analysis. Therefore, the model provides a cost effective and
quick approach to predict the impending wear in IC engine bearings
under various operating conditions.
Abstract: In wireless sensor network, sensor node transmits the
sensed data to the sink node in multi-hop communication
periodically. This high traffic induces congestion at the node which is
present one-hop distance to the sink node. The packet transmission
and reception rate of these nodes should be very high, when
compared to other sensor nodes in the network. Therefore, the energy
consumption of that node is very high and this effect is known as the
“funneling effect”. The tree based-data aggregation technique
(TBDA) is used to reduce the energy consumption of the node. The
throughput of the overall performance shows a considerable decrease
in the number of packet transmissions to the sink node. The proposed
scheme, TBDA, avoids the funneling effect and extends the lifetime
of the wireless sensor network. The average case time complexity for
inserting the node in the tree is O(n log n) and for the worst case time
complexity is O(n2).
Abstract: In this paper, an attempt has been made for the design
of a robotic library using an intelligent system. The robot works on
the ARM microprocessor, motor driver circuit with 5 degrees of
freedom with Wi-Fi and GPS based communication protocol. The
authenticity of the library books is controlled by RFID. The proposed
robotic library system is facilitated with embedded system and ARM.
In this library issuance system, the previous potential readers’
authentic review reports have been taken into consideration for
recommending suitable books to the deserving new users and the
issuance of books or periodicals is based on the users’ decision. We
have conjectured that the Wi-Fi based robotic library management
system would allow fast transaction of books issuance and it also
produces quality readers.
Abstract: Test automation allows performing difficult and time
consuming manual software testing tasks efficiently, quickly and
repeatedly. However, development and maintenance of automated
tests is expensive, so it needs a proper prioritization what to automate
first. This paper describes a simple yet efficient approach for such
prioritization of test cases based on the effort needed for both manual
execution and software test automation. The suggested approach is
very flexible because it allows working with a variety of assessment
methods, and adding or removing new candidates at any time. The
theoretical ideas presented in this article have been successfully
applied in real world situations in several software companies by the
authors and their colleagues including testing of real estate websites,
cryptographic and authentication solutions, OSGi-based middleware
framework that has been applied in various systems for smart homes,
connected cars, production plants, sensors, home appliances, car head
units and engine control units (ECU), vending machines, medical
devices, industry equipment and other devices that either contain or
are connected to an embedded service gateway.
Abstract: Currently, there are few user friendly Weigh-in-
Motion (WIM) data analysis softwares available which can produce
traffic input data for the recently developed AASHTOWare pavement
Mechanistic-Empirical (ME) design software. However, these
softwares have only rudimentary Quality Control (QC) processes.
Therefore, they cannot properly deal with erroneous WIM data. As
the pavement performance is highly sensible to the quality of WIM
data, it is highly recommended to use more refined QC process on
raw WIM data to get a good result. This study develops a userfriendly
software, which can produce traffic input for the ME design
software. This software takes the raw data (Class and Weight data)
collected from the WIM station and processes it with a sophisticated
QC procedure. Traffic data such as traffic volume, traffic distribution,
axle load spectra, etc. can be obtained from this software; which can
directly be used in the ME design software.