Abstract: To focus on the vibration mode of a cone loudspeaker,
which acts as an electroacoustic transducer, excitation experiments
were performed using two types of loudspeaker units: one employing
an impulse hammer and the other a sweep signal. The on-axis sound
pressure frequency properties of the loudspeaker were evaluated, and
the characteristic properties of the loudspeakers were successfully
determined in both excitation experiments. Moreover, under
conditions identical to the experiment conditions, a coupled analysis of
the vibration-acoustics of the cone loudspeaker was performed using
an acoustic analysis software program that considers the impact of
damping caused by air viscosity. The result of sound pressure
frequency properties with the numerical analysis are the most closely
match that measured in the excitation experiments over a wide range
of frequency bands.
Abstract: This project aims at building an efficient and
automatic power monitoring SCADA system, which is capable of
monitoring the electrical parameters of high voltage powered devices
in real time for example RMS voltage and current, frequency, energy
consumed, power factor etc. The system uses RS-485 serial
communication interface to transfer data over longer distances.
Embedded C programming is the platform used to develop two
hardware modules namely: RTU and Master Station modules, which
both use the CC2540 BLE 4.0 microcontroller configured in slave /
master mode. The Si8900 galvanic ally isolated microchip is used to
perform ADC externally. The hardware communicates via UART
port and sends data to the user PC using the USB port. Labview
software is used to design a user interface to display current state of
the power loads being monitored as well as logs data to excel
spreadsheet file. An understanding of the Si8900’s auto baud rate
process is key to successful implementation of this project.
Abstract: The material selection problem is concerned with the
determination of the right material for a certain product to optimize
certain performance indices in that product such as mass, energy
density, and power-to-weight ratio. This paper is concerned about
optimizing the selection of the manufacturing process along with the
material used in the product under performance indices and
availability constraints. In this paper, the material selection problem
is formulated using binary programming and solved by genetic
algorithm. The objective function of the model is to minimize the
total manufacturing cost under performance indices and material and
manufacturing process availability constraints.
Abstract: Hydrologic models are increasingly used as tools to
predict stormwater quantity and quality from urban catchments.
However, due to a range of practical issues, most models produce
gross errors in simulating complex hydraulic and hydrologic systems.
Difficulty in finding a robust approach for model calibration is one of
the main issues. Though automatic calibration techniques are
available, they are rarely used in common commercial hydraulic and
hydrologic modelling software e.g. MIKE URBAN. This is partly
due to the need for a large number of parameters and large datasets in
the calibration process. To overcome this practical issue, a
framework for automatic calibration of a hydrologic model was
developed in R platform and presented in this paper. The model was
developed based on the time-area conceptualization. Four calibration
parameters, including initial loss, reduction factor, time of
concentration and time-lag were considered as the primary set of
parameters. Using these parameters, automatic calibration was
performed using Approximate Bayesian Computation (ABC). ABC is
a simulation-based technique for performing Bayesian inference
when the likelihood is intractable or computationally expensive to
compute. To test the performance and usefulness, the technique was
used to simulate three small catchments in Gold Coast. For
comparison, simulation outcomes from the same three catchments
using commercial modelling software, MIKE URBAN were used.
The graphical comparison shows strong agreement of MIKE URBAN
result within the upper and lower 95% credible intervals of posterior
predictions as obtained via ABC. Statistical validation for posterior
predictions of runoff result using coefficient of determination (CD),
root mean square error (RMSE) and maximum error (ME) was found
reasonable for three study catchments. The main benefit of using
ABC over MIKE URBAN is that ABC provides a posterior
distribution for runoff flow prediction, and therefore associated
uncertainty in predictions can be obtained. In contrast, MIKE
URBAN just provides a point estimate. Based on the results of the
analysis, it appears as though ABC the developed framework
performs well for automatic calibration.
Abstract: An experiment to verify the relationships between
physiological indexes of an e-learner and the presence or absence of an
operation during e-learning is described. Electroencephalogram
(EEG), hemoencephalography (HEG), skin conductance (SC), and
blood volume pulse (BVP) values were measured while participants
performed experimental learning tasks. The results show that there are
significant differences between the SC values when reading with
clicking on learning materials and the SC values when reading without
clicking, and between the HEG ratio when reading (with and without
clicking) and the HEG ratio when resting for four of five participants.
We conclude that the SC signals can be used to estimate whether or not
a learner is performing an active task and that the HEG ratios can be
used to estimate whether a learner is learning.
Abstract: The effect of upstream surface roughness over a
smooth forward facing step in an open channel was investigated
using a particle image velocimetry technique. Three different
upstream surface topographies consisting of hydraulically smooth
wall, sandpaper 36 grit and sand grains were examined. Besides the
wall roughness conditions, all other upstream flow characteristics
were kept constant. It was also observed that upstream roughness
decreased the approach velocity by 2% and 10% but increased the
turbulence intensity by 14% and 35% at the wall-normal distance
corresponding to the top plane of the step compared to smooth
upstream. The results showed that roughness decreased the
reattachment lengths by 14% and 30% compared to smooth upstream.
Although the magnitudes of maximum positive and negative
Reynolds shear stress in separated and reattached region were 0.02Ue
for all the cases, the physical size of both the maximum and
minimum contour levels were decreased by increasing upstream
roughness.
Abstract: Liquid storage tanks have become widespread during the recent decades due to their extensive usage. Analysis of liquid containing tanks is known to be complex due to hydrodynamic force exerted on tank which makes the analysis a complex one. The objective of this research is to carry out analysis of liquid domain along with structural interaction for various geometries of circular tanks considering seismic effects. An attempt has been made to determine hydrodynamic pressure distribution on the tank wall considering impulsive and convective components of liquid mass. To get a better picture, a comparative study of Draft IS 1893 Part 2, ACI 350.3 and Eurocode 8 for Circular Shaped Tank has been performed. Further, the differences in the magnitude of shear and moment at base as obtained from static (IS 3370 IV) and dynamic (Draft IS 1892 Part 2) analysis of ground supported circular tank highlight the need for us to mature from the old code to a newer code, which is more accurate and reliable.
Abstract: In recent years, a wide variety of applications are developed with Support Vector Machines -SVM- methods and Artificial Neural Networks -ANN-. In general, these methods depend on intrusion knowledge databases such as KDD99, ISCX, and CAIDA among others. New classes of detectors are generated by machine learning techniques, trained and tested over network databases. Thereafter, detectors are employed to detect anomalies in network communication scenarios according to user’s connections behavior. The first detector based on training dataset is deployed in different real-world networks with mobile and non-mobile devices to analyze the performance and accuracy over static detection. The vulnerabilities are based on previous work in telemedicine apps that were developed on the research group. This paper presents the differences on detections results between some network scenarios by applying traditional detectors deployed with artificial neural networks and support vector machines.
Abstract: The effectiveness of microchannels in enhancing heat
transfer has been demonstrated in the semiconductor industry. In
order to tap the microscale heat transfer effects into macro
geometries, overcoming the cost and technological constraints,
microscale passages were created in macro geometries machined
using conventional fabrication methods. A cylindrical insert was
placed within a pipe, and geometrical profiles were created on the
outer surface of the insert to enhance heat transfer under steady-state
single-phase liquid flow conditions. However, while heat transfer
coefficient values of above 10 kW/m2·K were achieved, the heat
transfer enhancement was accompanied by undesirable pressure drop
increment. Therefore, this study aims to address the high pressure
drop issue using Constructal theory, a universal design law for both
animate and inanimate systems. Two designs based on Constructal theory were developed to study
the effectiveness of Constructal features in reducing the pressure drop
increment as compared to parallel channels, which are commonly
found in microchannel fabrication. The hydrodynamic and heat
transfer performance for the Tree insert and Constructal fin (Cfin)
insert were studied using experimental methods, and the underlying
mechanisms were substantiated by numerical results. In technical
terms, the objective is to achieve at least comparable increment in
both heat transfer coefficient and pressure drop, if not higher
increment in the former parameter. Results show that the Tree insert improved the heat transfer
performance by more than 16 percent at low flow rates, as compared
to the Tree-parallel insert. However, the heat transfer enhancement
reduced to less than 5 percent at high Reynolds numbers. On the
other hand, the pressure drop increment stayed almost constant at 20
percent. This suggests that the Tree insert has better heat transfer
performance in the low Reynolds number region. More importantly,
the Cfin insert displayed improved heat transfer performance along
with favourable hydrodynamic performance, as compared to Cfinparallel
insert, at all flow rates in this study. At 2 L/min, the
enhancement of heat transfer was more than 30 percent, with 20
percent pressure drop increment, as compared to Cfin-parallel insert.
Furthermore, comparable increment in both heat transfer coefficient
and pressure drop was observed at 8 L/min. In other words, the Cfin
insert successfully achieved the objective of this study. Analysis of the results suggests that bifurcation of flows is
effective in reducing the increment in pressure drop relative to heat
transfer enhancement. Optimising the geometries of the Constructal
fins is therefore the potential future study in achieving a bigger stride
in energy efficiency at much lower costs.
Abstract: Device-to-device (D2D) communication is considered a
promising technique to provide wireless peer-to-peer communication
services. Due to increasing demand on mobile services, available
spectrum for radio frequency (RF) based communications becomes
scarce. Recently, visible light communications (VLC) has evolved
as a high speed wireless data transmission technology for indoor
environments with abundant available bandwidth. In this paper,
a novel VLC based D2D communication that provides wireless
peer-to-peer communication is proposed. Potential low operating
power devices for an efficient D2D communication over increasing
distance of separation between devices is analyzed. Optical repeaters
(OR) are also proposed to enhance the performance in an environment
where direct D2D communications yield degraded performance.
Simulation results show that VLC plays an important role in
providing efficient D2D communication up to a distance of 1 m
between devices. It is also found that the OR significantly improves
the coverage distance up to 3.5 m.
Abstract: In this paper, a desiccant solar unit for air
conditioning and desalination is presented first. Secondly, a dynamic
modelling study of the desiccant wheel is developed. After that, a
simulation study and an experimental investigation of the behaviour
of desiccant wheel are developed. The experimental investigation is
done in the chamber of commerce in Freiburg-Germany. Indeed, the
variations of calculated and measured temperatures and specific
humidity of dehumidified and rejected air are presented where a good
agreement is found when comparing the model predictions with
experimental data under the considered range of operating conditions.
Finally, the study of the compartments of desalination and water
condensation shows that the unit can produce an acceptable quantity
of water at the same time of the air conditioning operation.
Abstract: In military aviation, the use of flight simulators has proliferated recently in order to train fifth generation fighter pilots. With these simulators, pilots can carry out real-time flights resulting in seeing their faults and can perform emergency drills prior to real flights. Since we cannot risk losing the aircraft and the pilot himself/herself in the flight training process, flight simulators are of great importance to adapt the fighter pilots competently to real flights aboard the fifth generation aircraft. The real flights are impossible to simulate thoroughly on the ground. To some extent, the fixed-based simulators may assist the pilot to steer aircraft technically and visually but flight simulators can’t trick the pilot’s vestibular, sensory, and perceptual systems without motion platforms. This paper discusses the benefits of motion simulators for fifth generation fighter pilots’ training in preference to the fixed-based counterparts by analyzing their pros and cons.
Abstract: The tribological test with Pin-On-Disc configuration
measures friction and wear properties in dry or lubricated sliding
surfaces of a variety of materials and coatings. Polymeric matrix
composites loaded with mineral filler were used, 1%, 3%, 10%, 30%,
and 50% mass percentage of filler, to reduce the material cost by
using mineral tailings. Using a pin-on-disc tribometer to quantify
coefficient of friction and wear resistance of the specimens. The
parameters known to performing the test were 300 rpm rotation,
normal load of 16N and duration of 33.5 minutes. The composite
with 10% mineral filler performed better, considering that the wear
resistance was good when compared to the other compositions and an
average low coefficient of friction, in the order of μ ≤ 0.15.
Abstract: Solar water heating is a thermodynamic process of
heating water using sunlight with the help of solar water heater. Thus,
solar water heater is a device used to harness solar energy. In this
paper, a modified solar water heating system (MSWHS) has been
proposed over flat plate collector (FPC) and Evacuated tube collector
(ETC). The modifications include selection of materials other than
glass, and glass wool which are conventionally used for fabricating
FPC and ETC. Some modifications in design have also been
proposed. Its collector is made of double layer of semi-cylindrical
acrylic tubes and fibre reinforced plastic (FRP) insulation base. Water
tank is made of double layer of acrylic sheet except base and north
wall. FRP is used in base and north wall of the water tank. A concept
of equivalent thickness has been utilised for calculating the
dimensions of collector plate, acrylic tube and tank. A thermal model for the proposed design of MSWHS is developed
and simulation is carried out on MATLAB for the capacity of 200L
MSWHS having collector area of 1.6 m2, length of acrylic tubes of
2m at an inclination angle 25° which is taken nearly equal to the
latitude of the given location. Latitude of Allahabad is 24.45° N. The
results show that the maximum temperature of water in tank and tube
has been found to be 71.2°C and 73.3°C at 17:00hr and 16:00hr
respectively in March for the climatic data of Allahabad. Theoretical performance analysis has been carried out by varying
number of tubes of collector, the tank capacity and climatic data for
given months of winter and summer.
Abstract: HMS Industrial Networks AB has been recognized as
one of the most innovative companies in the industrial
communication industry worldwide. The creation of their Anybus
innovation during the 1990s contributed considerably to the
company’s success. From inception, HMS’ employees were
innovating for the purpose of creating new business (the creation
phase). After the Anybus innovation, they began the process of
internationalization (the commercialization phase), which in turn led
them to concentrate on cost reduction, product quality, delivery
precision, operational efficiency, and increasing growth (the growth
phase). As a result of this transformation, performing new radical
innovations have become more complicated. The purpose of our research was to explore the dynamics of
innovation at HMS from the aspect of key actors, activities, and
events, over the three phases, in order to understand what led to the
creation of their Anybus innovation, and why it has become
increasingly challenging for HMS to create new radical innovations
for the future. Our research methodology was based on a longitudinal,
retrospective study from the inception of HMS in 1988 to 2014, a
single case study inspired by the grounded theory approach. We
conducted 47 interviews and collected 1 024 historical documents for
our research. Our analysis has revealed that HMS’ success in creating the
Anybus, and developing a successful business around the innovation,
was based on three main capabilities – cultivating customer relations
on different managerial and organizational levels, inspiring business
relations, and balancing complementary human assets for the purpose
of business creation. The success of HMS has turned the management’s attention away
from past activities of key actors, of their behavior, and how they
influenced and stimulated the creation of radical innovations.
Nowadays, they are rhetorically focusing on creativity and
innovation. All the while, their real actions put emphasis on growth,
cost reduction, product quality, delivery precision, operational
efficiency, and moneymaking. In the process of becoming an
international company, HMS gradually refocused. In so doing they
became profitable and successful, but they also forgot what made
them innovative in the first place. Fortunately, HMS’ management
has come to realize that this is the case and they are now in search of
recapturing innovation once again. Our analysis indicates that HMS’ management is facing several
barriers to innovation related path dependency and other lock-in
phenomena. HMS’ management has been captured, trapped in their
mindset and actions, by the success of the past. But now their future has to be secured, and they have come to realize that moneymaking is
not everything. In recent years, HMS’ management have begun to
search for innovation once more, in order to recapture their past
capabilities for creating radical innovations. In order to unlock their
managerial perceptions of customer needs and their counter-innovation
driven activities and events, to utilize the full potential of
their employees and capture the innovation opportunity for the future.
Abstract: In general, it is desirable to finish the weld quickly,
before a large volume of surrounding metal heats up and expands.
The welding process used, type, welding current and speed of travel,
thus, affect the degree of shrinkage and distortion of a weldment. The
use of mechanized welding equipment reduces welding time, metal
affected zone and consequently distortion. This article helps to define
what weld distortion is and then provide a practical understanding of
the causes of distortion, effects of shrinkage in butt joint welded
assemblies using TI6AL4VA and Aluminium AA2024 alloy sheet.
The beam offset position to the joint interface towards titanium and
aluminium side. The factors affecting distortion during welding is
also given. Test results reveal that welding speed is the significant
parameter to decide the extent of distortion. Also welding from Al
side reduces the distortion while Ti side increases the distortion.
Abstract: Surface characteristics of Bacillus megaterium strain
were investigated; zeta potential, FTIR and contact angle were
measured. Surface energy components including Lifshitz-van der
Waals, Hamaker constant, and acid/base components (Lewis
acid/Lewis base) were calculated from the contact angle data. The
results showed that the microbial cells were negatively charged over
all pH regions with high values at alkaline region. A hydrophilic
nature for the strain was confirmed by contact angle and free energy
of adhesion between microbial cells. Adsorption affinity of the strain
toward dolomite was studied at different pH values. The results
showed that the cells had a high affinity to dolomite at acid pH
comparing to neutral and alkaline pH. Extended DLVO theory was
applied to calculate interaction energy between B. megaterium cells
and dolomite particles. The adsorption results were in agreement with
the results of Extended DLVO approach. Surface changes occurred
on dolomite surface after the bio-treatment were monitored; contact
angle decreased from 69° to 38° and the mineral’s floatability
decreased from 95% to 25% after the treatment.
Abstract: Sisal leaves were subjected to enzymatic retting
method to extract the sisal fibre. A portion of the fibre was pretreated
with alkali (NaOH), and further treated with benzoyl chloride
and silane treatment reagents. Both the treated and untreated Sisal
fibre composites were used to fabricate the composite by hand lay-up
technique using unsaturated polyester resin. Tensile, flexural, water
absorption, density, thickness swelling and chemical resistant tests
were conducted and evaluated on the composites. Results obtained
for all the parameters showed an increase in the treated fibre
compared to untreated fibre. FT-IR spectra results ascertained the
inclusion of benzoyl and silane groups on the fibre surface. Scanning
electron microscopy (SEM) result obtained showed variation in the
morphology of the treated and untreated fibre. Chemical modification
was found to improve adhesion of the fibre to the matrix, as well as
physico-mechanical properties of the composites.
Abstract: This paper discusses the intake of combining multi-criteria
decision analysis (MCDA) with OLAP systems, to generate
an integrated analysis process dealing with complex multi-criteria
decision-making situations. In this context, a multi-agent modeling is
presented for decision support systems by combining multi-criteria
decision analysis (MCDA) with OLAP systems. The proposed
modeling which consists in performing the multi-agent system
(MAS) architecture, procedure and protocol of the negotiation model
is elaborated as a decision support tool for complex decision-making
environments. Our objective is to take advantage from the multi-agent
system which distributes resources and computational
capabilities across interconnected agents, and provide a problem
modeling in terms of autonomous interacting component-agents.
Thus, the identification and evaluation of criteria as well as the
evaluation and ranking of alternatives in a decision support situation
will be performed by organizing tasks and user preferences between
different agents in order to reach the right decision. At the end, an
illustrative example is conducted to demonstrate the function and
effectiveness of our MAS modeling.
Abstract: Reinforced earth structures are generally subjected to cyclic loading generated from earthquakes. This paper presents a summary of the results and analyses of a testing program carried out in a large-scale multi-function geosynthetic testing apparatus that accommodates soil samples up to 1.0 m3. This apparatus performs different shear and pullout tests under both static and cyclic loading. The testing program was carried out to investigate the controlling factors affecting soil/geogrid interaction under cyclic loading. The extensibility of the geogrids, the applied normal stresses, the characteristics of the cyclic loading (frequency, and amplitude), and initial static load within the geogrid sheet were considered in the testing program. Based on the findings of the testing program, the effect of these parameters on the pullout resistance of geogrids, as well as the displacement mobility under cyclic loading were evaluated. Conclusions and recommendations for the design of reinforced earth walls under cyclic loading are presented.