Abstract: Implementation of advanced technologies requires
sophisticated instruments that deal with the operation, control,
restoration and protection of rapidly growing power system network
under normal and abnormal conditions. Presently, the applications of
Phasor Measurement Unit (PMU) are widely found in real time
operation, monitoring, controlling and analysis of power system
network as it eliminates the various limitations of supervisory control
and data acquisition system (SCADA) conventionally used in power
system. The use of PMU data is very rapidly increasing its
importance for online and offline analysis. Wide area measurement
system (WAMS) is developed as new technology by use of multiple
PMUs in power system. The present paper proposes a model of
Matlab based PMU using Discrete Fourier Transform (DFT)
algorithm and evaluation of its operation under different
contingencies. In this paper, PMU based two bus system having
WAMS network is presented as a case study.
Abstract: Fibre cement plates, often used in construction,
generally are made using quartz as an inert material, cement as a
binder and cellulose as a fibre. This paper, first of all, investigates the
mechanical properties and durability of fibre cement plates when
quartz is both partly and fully replaced with diatomite. Diatomite
does not only have lower density compared to quartz but also has
high pozzolanic activity. The main objective of this paper is the
investigation of the effects of supplementary cementing materials
(SCMs) on the short and long term mechanical properties and
durability characteristics of fibre cement plates prepared using
diatomite. Supplementary cementing materials such as ground
granulated blast furnace slug (GGBS) and fly ash (FA) are used in
this study. Volume proportions of 10, 20, 30 and 40% of GGBS and
FA are used as partial replacement materials to cement. Short and
long term mechanical properties such as compressive and flexural
strengths as well as sorptivity characteristics and mass were
investigated. Consistency and setting time at each replacement levels
of SCMs were also recorded. The effects of using supplementary
cementing materials on the carbonation and sulphate resistance of
fibre cement plates were then experimented. The results, first of all,
show that the use of diatomite as a full or partial replacement to
quartz resulted in a systematic decrease in total mass of the fibre
cement plates. The reduction of mass was largely due to the lower
density and finer particle size of diatomite compared to quartz. The
use of diatomite did not only reduce the mass of these plates but also
increased the compressive strength significantly as a result of its high
pozzolanic activity. The replacement levels of both GGBS and FA
resulted in a systematic decrease in short term compressive strength
with increasing replacement levels. This was essentially expected as
the total rate of hydration is much lower in GGBS and FA than that
of cement. Long term results however, indicated that the compressive
strength of fibre cement plates prepared using both GGBS and FA
increases with time and hence the compressive strength of plates
prepared using SCMs is either equivalent or more than the
compressive strength of plates prepared using cement alone.
Durability characteristics of fibre cement plates prepared using SCMs
were enhanced significantly. Measurements of sopritivty
characteristics were also indicated that the plates prepared using
SCMs has much lower water absorption capacities compared to
plates prepared cement alone. Much higher resistance to carbonation
and sulphate attach were observed with plates prepared using SCMs.
The results presented in this paper show that the use of SCMs does
not only support the production of more sustainable construction
materials but also enhances the mechanical properties and durability
characteristics of fibre cement plates.
Abstract: This paper presents a new automatic vehicle detection
method from very high resolution aerial images to measure traffic
density. The proposed method starts by extracting road regions from
image using road vector data. Then, the road image is divided into
equal sections considering resolution of the images. Gradient vectors
of the road image are computed from edge map of the corresponding
image. Gradient vectors on the each boundary of the sections are
divided where the gradient vectors significantly change their
directions. Finally, number of vehicles in each section is carried out
by calculating the standard deviation of the gradient vectors in each
group and accepting the group as vehicle that has standard deviation
above predefined threshold value. The proposed method was tested in
four very high resolution aerial images acquired from Istanbul,
Turkey which illustrate roads and vehicles with diverse
characteristics. The results show the reliability of the proposed
method in detecting vehicles by producing 86% overall F1 accuracy
value.
Abstract: Continuous upflow filters can combine the nutrient
(nitrogen and phosphate) and suspended solid removal in one unit
process. The contaminant removal could be achieved chemically or
biologically; in both processes the filter removal efficiency depends
on the interaction between the packed filter media and the influent. In
this paper a residence time distribution (RTD) study was carried out
to understand and compare the transfer behaviour of contaminants
through a selected filter media packed in a laboratory-scale
continuous up flow filter; the selected filter media are limestone and
white dolomite. The experimental work was conducted by injecting a
tracer (red drain dye tracer –RDD) into the filtration system and then
measuring the tracer concentration at the outflow as a function of
time; the tracer injection was applied at hydraulic loading rates
(HLRs) (3.8 to 15.2 m h-1). The results were analysed according to
the cumulative distribution function F(t) to estimate the residence
time of the tracer molecules inside the filter media. The mean
residence time (MRT) and variance σ2 are two moments of RTD that
were calculated to compare the RTD characteristics of limestone with
white dolomite. The results showed that the exit-age distribution of
the tracer looks better at HLRs (3.8 to 7.6 m h-1) and (3.8 m h-1) for
limestone and white dolomite respectively. At these HLRs the
cumulative distribution function F(t) revealed that the residence time
of the tracer inside the limestone was longer than in the white
dolomite; whereas all the tracer took 8 minutes to leave the white
dolomite at 3.8 m h-1. On the other hand, the same amount of the
tracer took 10 minutes to leave the limestone at the same HLR. In
conclusion, the determination of the optimal level of hydraulic
loading rate, which achieved the better influent distribution over the
filtration system, helps to identify the applicability of the material as
filter media. Further work will be applied to examine the efficiency
of the limestone and white dolomite for phosphate removal by
pumping a phosphate solution into the filter at HLRs (3.8 to 7.6 m h-1).
Abstract: Model predictive control is a kind of optimal feedback
control in which control performance over a finite future is optimized
with a performance index that has a moving initial time and a moving
terminal time. This paper examines the stability of model predictive
control for linear discrete-time systems with additive stochastic
disturbances. A sufficient condition for the stability of the closed-loop
system with model predictive control is derived by means of a linear
matrix inequality. The objective of this paper is to show the results
of computational simulations in order to verify the effectiveness of
the obtained stability condition.
Abstract: Dynamics of a rotor supported by air bearings is
strongly depends on the pressure distribution between the rotor and
the bearing. In this study, internal pressure in air bearings is
numerical and experimental analyzed for different radial clearances.
Firstly the pressure distribution between rotor and bearing is modeled
using Reynold's equation and this model is solved numerically. The
rotor-bearing system is also modeled in four degree of freedom and it
is simulated for different radial clearances. Then, in order to validate
numerical results, a test rig is designed and the rotor bearing system
is run under the same operational conditions. Pressure signals of left
and right bearings are recorded. Internal pressure variations are
compared for numerical and experimental results for different radial
clearances.
Abstract: This paper presents development results of usage of
C-OTDR monitoring systems for rail traffic management. The COTDR
method is based on vibrosensitive properties of optical fibers.
Analysis of Rayleigh backscattering radiation parameters changes
which take place due to microscopic seismoacoustic impacts on the
optical fiber allows to determine seismoacoustic emission source
positions and to identify their types. This approach proved successful
for rail traffic management (moving block system, weigh- in-motion
system etc.).
Abstract: In the field of fashion design, 3D Mannequin is a kind
of assisting tool which could rapidly realize the design concepts.
While the concept of 3D Mannequin is applied to the computer added
fashion design, it will connect with the development and the
application of design platform and system. Thus, the situation
mentioned above revealed a truth that it is very critical to develop a
module of 3D Mannequin which would correspond with the necessity
of fashion design. This research proposes a concrete plan that
developing and constructing a system of 3D Mannequin with Kinect.
In the content, ergonomic measurements of objective human features
could be attained real-time through the implement with depth camera
of Kinect, and then the mesh morphing can be implemented through
transformed the locations of the control-points on the model by
inputting those ergonomic data to get an exclusive 3D mannequin
model. In the proposed methodology, after the scanned points from the
Kinect are revised for accuracy and smoothening, a complete human
feature would be reconstructed by the ICP algorithm with the method
of image processing. Also, the objective human feature could be
recognized to analyze and get real measurements. Furthermore, the
data of ergonomic measurements could be applied to shape morphing
for the division of 3D Mannequin reconstructed by feature curves. Due
to a standardized and customer-oriented 3D Mannequin would be
generated by the implement of subdivision, the research could be
applied to the fashion design or the presentation and display of 3D
virtual clothes. In order to examine the practicality of research
structure, a system of 3D Mannequin would be constructed with JAVA
program in this study. Through the revision of experiments the
practicability-contained research result would come out.
Abstract: UAV’s are small remote operated or automated aerial
surveillance systems without a human pilot aboard. UAV’s generally
finds its use in military and special operation application, a recent
growing trend in UAV’s finds its application in several civil and nonmilitary
works such as inspection of power or pipelines. The
objective of this paper is the augmentation of a UAV in order to
replace the existing expensive sonar (Sound Navigation And
Ranging) based equipment amongst small scale fisherman, for whom
access to sonar equipment are restricted due to limited economic
resources. The surveillance equipment’s present in the UAV will
relay data and GPS (Global Positioning System) location onto a
receiver on the fishing boat using RF signals, using which the
location of the schools of fishes can be found. In addition to this, an
emergency beacon system is present for rescue operations and drone
recovery.
Abstract: This study, for its research subjects, uses patients who
had undergone total knee replacement surgery from the database of the
National Health Insurance Administration. Through the review of
literatures and the interviews with physicians, important factors are
selected after careful screening. Then using Cross Entropy Method,
Genetic Algorithm Logistic Regression, and Particle Swarm
Optimization, the weight of each factor is calculated and obtained. In
the meantime, Excel VBA and Case Based Reasoning are combined
and adopted to evaluate the system. Results show no significant
difference found through Genetic Algorithm Logistic Regression and
Particle Swarm Optimization with over 97% accuracy in both
methods. Both ROC areas are above 0.87. This study can provide
critical reference to medical personnel as clinical assessment to
effectively enhance medical care quality and efficiency, prevent
unnecessary waste, and provide practical advantages to resource
allocation to medical institutes.
Abstract: In this paper a new model for center of motion
creating is proposed. This new method uses cables. So, it is very
useful in robots because it is light and has easy assembling process.
In the robots which need to be in touch with some things this method
is so useful. It will be described in the following. The accuracy of the
idea is proved by two experiments. This system could be used in the
robots which need a fixed point in the contact with some things and
make a circular motion.
Abstract: This paper describes the main features of a knowledge-based system evaluation method. System evaluation is placed in the context of a hybrid legal decision-support system, Advisory Support for Home Settlement in Divorce (ASHSD). Legal knowledge for ASHSD is represented in two forms, as rules and previously decided cases. Besides distinguishing the two different forms of knowledge representation, the paper outlines the actual use of these forms in a computational framework that is designed to generate a plausible solution for a given case, by using rule-based reasoning (RBR) and case-based reasoning (CBR) in an integrated environment. The nature of suitability assessment of a solution has been considered as a multiple criteria decision-making process in ASHAD evaluation. The evaluation was performed by a combination of discussions and questionnaires with different user groups. The answers to questionnaires used in this evaluations method have been measured as a fuzzy linguistic term. The finding suggests that fuzzy linguistic evaluation is practical and meaningful in knowledge-based system development purpose.
Abstract: This paper presents an experimental study on
structural performance of an innovative noise barrier consisting of
poly-block, light polyurethane foam (LPF) and polyurea. This wall
system (flexi-wall) is intended to be employed as a vertical extension
to existing sound barriers in an accelerated construction method. To
aid in the wall design, several mechanical tests were conducted on
LPF specimens and two full-scale walls were then fabricated
employing the same LPF material. The full-scale walls were
subjected to lateral loading in order to establish their lateral
resistance. A cyclic fatigue test was also performed on a full-scale
flexi-wall in order to evaluate the performance of the wall under a
repetitive loading condition. The result of the experiments indicated
the suitability of flexi-wall in accelerated construction and confirmed
that the structural performance of the wall system under lateral
loading is satisfactory for the sound barrier application. The
experimental results were discussed and a preliminary design
procedure for application of flexi-wall in sound barrier applications
was also developed.
Abstract: The Figaro AM-1 sensor module which employs TGS
2600 model gas sensor in air quality assessment was used. The
system was coupled with a microprocessor that enables sensor
module to create warning message via telephone. This low cot sensor
system’s performance was compared with a DiagNose II commercial
electronic nose system. Both air quality sensor and electronic nose
system employ metal oxide chemical gas sensors. In the study
experimental setup, data acquisition methods for electronic nose
system, and performance of the low cost air quality system were
evaluated and explained.
Abstract: This paper focuses on I/O optimizations of N-hybrid
(New-Form of hybrid), which provides a hybrid file system space
constructed on SSD and HDD. Although the promising potentials of
SSD, such as the absence of mechanical moving overhead and high
random I/O throughput, have drawn a lot of attentions from IT
enterprises, its high ratio of cost/capacity makes it less desirable to
build a large-scale data storage subsystem composed of only SSDs. In
this paper, we present N-hybrid that attempts to integrate the strengths
of SSD and HDD, to offer a single, large hybrid file system space.
Several experiments were conducted to verify the performance of
N-hybrid.
Abstract: This paper presents an application of a “Systematic
Soft Domain Driven Design Framework” as a soft systems approach
to domain-driven design of information systems development. The
framework use SSM as a guiding methodology within which we have
embedded a sequence of design tasks based on the UML leading to
the implementation of a software system using the Naked Objects
framework. This framework have been used in action research
projects that have involved the investigation and modelling of
business processes using object-oriented domain models and the
implementation of software systems based on those domain models.
Within this framework, Soft Systems Methodology (SSM) is used as
a guiding methodology to explore the problem situation and to
develop the domain model using UML for the given business
domain. The framework is proposed and evaluated in our previous
works, and a real case study “Information Retrieval System for
academic research” is used, in this paper, to show further practice and
evaluation of the framework in different business domain. We argue
that there are advantages from combining and using techniques from
different methodologies in this way for business domain modelling.
The framework is overviewed and justified as multimethodology
using Mingers multimethodology ideas.
Abstract: The future and the development of science is therefore
seen in interdisciplinary areas such as biomedical engineering. Selfassembled
structures, similar to stem cell niches would inhibit fast
division process and subsequently capture the stem cells from the
blood flow. By means of surface topography and the stiffness as well
as microstructure progenitor cells should be differentiated towards
the formation of endothelial cells monolayer which effectively will
inhibit activation of the coagulation cascade. The idea of the material
surface development met the interest of the clinical institutions,
which support the development of science in this area and are waiting
for scientific solutions that could contribute to the development of
heart assist systems. This would improve the efficiency of the
treatment of patients with myocardial failure, supported with artificial
heart assist systems. Innovative materials would enable the redesign,
in the post project activity, construction of ventricular heart assist.
Abstract: This paper proposed the comparison made between
Multi-Carrier Pulse Width Modulation, Sinusoidal Pulse Width
Modulation and Selective Harmonic Elimination Pulse Width
Modulation technique for minimization of Total Harmonic Distortion
in Cascaded H-Bridge Multi-Level Inverter. In Multicarrier Pulse
Width Modulation method by using Alternate Position of Disposition
scheme for switching pulse generation to Multi-Level Inverter.
Another carrier based approach; Sinusoidal Pulse Width Modulation
method is also implemented to define the switching pulse generation
system in the multi-level inverter. In Selective Harmonic Elimination
method using Genetic Algorithm and Particle Swarm Optimization
algorithm for define the required switching angles to eliminate low
order harmonics from the inverter output voltage waveform and
reduce the total harmonic distortion value. So, the results validate that
the Selective Harmonic Elimination Pulse Width Modulation method
does capably eliminate a great number of precise harmonics and
minimize the Total Harmonic Distortion value in output voltage
waveform in compared with Multi-Carrier Pulse Width Modulation
method, Sinusoidal Pulse Width Modulation method. In this paper,
comparison of simulation results shows that the Selective Harmonic
Elimination method can attain optimal harmonic minimization
solution better than Multi-Carrier Pulse Width Modulation method,
Sinusoidal Pulse Width Modulation method.
Abstract: In addition to environmental parameters like rain,
temperature diseases on crop is a major factor which affects
production quality & quantity of crop yield. Hence disease
management is a key issue in agriculture. For the management of
disease, it needs to be detected at early stage. So, treat it properly &
control spread of the disease. Now a day, it is possible to use the
images of diseased leaf to detect the type of disease by using image
processing techniques. This can be achieved by extracting features
from the images which can be further used with classification
algorithms or content based image retrieval systems. In this paper,
color image is used to extract the features such as mean and standard
deviation after the process of region cropping. The selected features
are taken from the cropped image with different image size samples.
Then, the extracted features are taken in to the account for
classification using Fuzzy Inference System (FIS).
Abstract: Out-migration is an important issue for Georgia as
well as since independence has loosed due to emigration one fifth of
its population. During Soviet time out-migration from USSR was
almost impossible and one of the most important instruments in
regulating population movement within the Soviet Union was the
system of compulsory residential registrations, so-called “propiska”.
Since independent here was not any regulation for migration from
Georgia. The majorities of Georgian migrants go abroad by tourist
visa and then overstay, becoming the irregular labor migrants. The
official statistics on migration published for this period was based on
the administrative system of population registration, were
insignificant in terms of numbers and did not represent the real scope
of these migration movements. This paper discusses the data quality
and methodology of migration statistics in Georgia and we are going
to answer the questions: what is the real reason of increasing
immigration flows according to the official numbers since 2000s?