Abstract: The aim of this study was to investigate the effects of
supplementing the diluent of roosters' semen with different levels of
olive oil on motility, viability, morphology and acrosome integrity of
chicken spermatozoa after in vitro storage for up to 72 h. Semen was
collected from 60 White Layer males (62 wk of age) kept in
separated floor pens and randomly divided into six treatment groups
(10 males in each group). Experimental groups were as follows: T1
:fresh semen, T2 : semen extended 1:1 with Al – Daraji 2 diluent
(AD2D) alone, T3 – T6 :semen samples extended 1:1 with AD2D
supplemented with 2 ml, 4 ml, 6 ml or 8 ml of olive oil / 100 ml of
diluent, respectively. Semen samples were then stored at 5 °C for 24
h, 48 h or 72 h. There was a clear influence of diluent
supplementation with olive oil on the spermatozoa motility profile;
olive oil groups (T3, T4, T5 and T6) recorded the highest scores of
mass activity and individual motility during all storage periods
compared to T1 and T2 groups. In addition, the inclusion of olive oil
into semen diluent (T3, T4, T5 and T6) gave significantly higher
percentages of viable spermatozoa, normal morphologically
spermatozoa and intact acrosomes irrespective of storage period.
These results clearly show that supplementation the diluent of
roosters' semen with olive oil can improve semen quality when
semen samples in vitro stored at 5 °C for up to 72 h.
Abstract: The aim of this research is to evaluate surface
roughness and develop a multiple regression model for surface roughness as a function of cutting parameters during the turning of
flame hardened medium carbon steel with TiN-Al2O3-TiCN coated inserts. An experimental plan of work and signal-to-noise ratio (S/N)
were used to relate the influence of turning parameters to the
workpiece surface finish utilizing Taguchi methodology. The effects
of turning parameters were studied by using the analysis of variance (ANOVA) method. Evaluated parameters were feed, cutting speed,
and depth of cut. It was found that the most significant interaction among the considered turning parameters was between depth of cut and feed. The average surface roughness (Ra) resulted by TiN-Al2O3-
TiCN coated inserts was about 2.44 μm and minimum value was 0.74 μm. In addition, the regression model was able to predict values for surface roughness in comparison with experimental values within
reasonable limit.
Abstract: The amplitude response of infrared (IR) sensors
depends on the reflectance properties of the target. Therefore, in
order to use IR sensor for measuring distances accurately, prior
knowledge of the surface must be known. This paper describes the
Phong Illumination Model for determining the properties of a surface
and subsequently calculating the distance to the surface. The angular
position of the IR sensor is computed as normal to the surface for
simplifying the calculation. Ultrasonic (US) sensor can provide the
initial information on distance to obtain the parameters for this
method. In addition, the experimental results obtained by using
LabView are discussed. More care should be taken when placing the
objects from the sensors during acquiring data since the small change
in angle could show very different distance than the actual one.
Since stereo camera vision systems do not perform well under some
environmental conditions such as plain wall, glass surfaces, or poor
lighting conditions, the IR and US sensors can be used additionally to
improve the overall vision systems of mobile robots.
Abstract: In this paper, an image adaptive, invisible digital
watermarking algorithm with Orthogonal Polynomials based
Transformation (OPT) is proposed, for copyright protection of digital
images. The proposed algorithm utilizes a visual model to determine
the watermarking strength necessary to invisibly embed the
watermark in the mid frequency AC coefficients of the cover image,
chosen with a secret key. The visual model is designed to generate a
Just Noticeable Distortion mask (JND) by analyzing the low level
image characteristics such as textures, edges and luminance of the
cover image in the orthogonal polynomials based transformation
domain. Since the secret key is required for both embedding and
extraction of watermark, it is not possible for an unauthorized user to
extract the embedded watermark. The proposed scheme is robust to
common image processing distortions like filtering, JPEG
compression and additive noise. Experimental results show that the
quality of OPT domain watermarked images is better than its DCT
counterpart.
Abstract: In this paper we investigate the influence of external
noise on the inference of network structures. The purpose of our
simulations is to gain insights in the experimental design of microarray
experiments to infer, e.g., transcription regulatory networks
from microarray experiments. Here external noise means, that the
dynamics of the system under investigation, e.g., temporal changes of
mRNA concentration, is affected by measurement errors. Additionally
to external noise another problem occurs in the context of microarray
experiments. Practically, it is not possible to monitor the mRNA
concentration over an arbitrary long time period as demanded by the
statistical methods used to learn the underlying network structure. For
this reason, we use only short time series to make our simulations
more biologically plausible.
Abstract: Nowadays, the performance required for concrete
structures is more complicated and diversified. Self-compacting
concrete is a fluid mixture suitable for placing in structures with
congested reinforcement without vibration. Self-compacting concrete
development must ensure a good balance between deformability and
stability. Also, compatibility is affected by the characteristics of
materials and the mix proportions; it becomes necessary to evolve a
procedure for mix design of SCC.
This paper presents an experimental procedure for the design of
self-compacting concrete mixes with different water-cement ratios
(w/c) and other constant ratios by local materials. The test results for
acceptance characteristics of self-compacting concrete such as slump
flow, V-funnel and L-Box are presented. Further, compressive
strength, tensile strength and modulus of elasticity of specimens were
also determined and results are included here
Abstract: In this paper a three dimensional thermal model of a
sliding contact system is proposed for both steady-state or transient
conditions. The influence of contact force, electric current and
ambient temperature on the temperature distribution, has been
investigated. A thermal analysis of the different type of the graphite
material of fixed electric contact and its influence on contact system
temperature rise, has been performed. To validate the three
dimensional thermal model, some experimental tests have been done.
There is a good correlation between experimental and simulation
results.
Abstract: In this paper a hybrid technique of Genetic Algorithm
and Simulated Annealing (HGASA) is applied for Fractal Image
Compression (FIC). With the help of this hybrid evolutionary
algorithm effort is made to reduce the search complexity of matching
between range block and domain block. The concept of Simulated
Annealing (SA) is incorporated into Genetic Algorithm (GA) in order
to avoid pre-mature convergence of the strings. One of the image
compression techniques in the spatial domain is Fractal Image
Compression but the main drawback of FIC is that it involves more
computational time due to global search. In order to improve the
computational time along with acceptable quality of the decoded
image, HGASA technique has been proposed. Experimental results
show that the proposed HGASA is a better method than GA in terms
of PSNR for Fractal image Compression.
Abstract: Repairing of the cracks by fiber metal laminates
(FMLs) was first done by some aeronautical laboratories in early
1970s. In this study, experimental investigations were done on the
effect of repairing the center-cracked aluminum plates using the FML
patches. The repairing processes were conducted to characterize the
response of the repaired structures to tensile tests. The composite
patches were made of one aluminum layer and two woven glassepoxy
composite layers. Three different crack lengths in three crack
angles and different patch lay-ups were examined. It was observed
for the lengthen cracks, the effect of increasing the crack angle on
ultimate tensile load in the structure was increase. It was indicated
that the situation of metal layer in the FML patches had an important
effect on the tensile response of the tested specimens. It was found
when the aluminum layer is farther, the ultimate tensile load has the
highest amount.
Abstract: This paper presents the experimental results of
comparison between leakage currents and discharge currents. The leakage currents were obtained on polluted porcelain insulator.
Whereas, the discharge currents were obtained on lightly artificial
polluted porcelain specimen. The conducted measurements were
leakage current or discharge current and applied voltage. The insulator or specimen was in a hermetically sealed chamber, and the
current waveforms were analyzed using FFT.
The result indicated that the leakage current (LC) on low RH condition the fifth harmonic would be visible, and followed by the
seventh harmonic. The insulator had capacitive property. Otherwise,
on 99% relative humidity, the fifth harmonic would also be visible,
and the phase angle reached up to 12.2 degree. Whereas, on discharge current, the third harmonic would be visible, and followed
by fifth harmonic. The third harmonic would increase as pressure reduced. On this condition, the specimen had a non-linear characteristics
Abstract: Flow-shop scheduling problem (FSP) deals with the
scheduling of a set of jobs that visit a set of machines in the same
order. The FSP is NP-hard, which means that an efficient algorithm
for solving the problem to optimality is unavailable. To meet the
requirements on time and to minimize the make-span performance of
large permutation flow-shop scheduling problems in which there are
sequence dependent setup times on each machine, this paper
develops one hybrid genetic algorithms (HGA). Proposed HGA
apply a modified approach to generate population of initial
chromosomes and also use an improved heuristic called the iterated
swap procedure to improve initial solutions. Also the author uses
three genetic operators to make good new offspring. The results are
compared to some recently developed heuristics and computational
experimental results show that the proposed HGA performs very
competitively with respect to accuracy and efficiency of solution.
Abstract: Research results and optimal parameters investigation
of laser cut and profiling of diamond and quartz substrates by
femtosecond laser pulses are presented. Profiles 10 μm in width, ~25
μm in depth and several millimeters long were made. Investigation of
boundaries quality has been carried out with the use of AFM
«Vecco». Possibility of technological formation of profiles and
micro-holes in diamond and quartz substrates with nanometer-scale
boundaries is shown. Experimental results of multilayer dielectric
cover treatment are also presented. Possibility of precise upper layer
(thickness of 70–140 nm) removal is demonstrated. Processes of thin
metal film (60 nm and 350 nm thick) treatment are considered.
Isolation tracks (conductance ~ 10-11 S) 1.6–2.5 μm in width in
conductive metal layers are formed.
Abstract: This paper presents the experimental results of silicone rubber housing material for 24kV lightning arrester under artificial accelerated ageing test based on IEC 61109 specifications. Specimens having inclined and alternated shed made of HTV silicone rubber with ATH content and having leakage distance 625 mm were tested continuously 1000 hrs in artificial salt fog chamber. After 1000 hrs of salt fog ageing test, obviously surface erosion was observed on trunk between the upper large shed and the lower small shed near the energized end. Decreasing in hydrophobicity and increasing in hardness were measured on tested specimen comparing with new specimen. Chemical analysis by ATR-FTIR confirmed the observation results.
Abstract: A thirty Rahmani weaned male lambs of average body weight (27.28±1.40 kg) were randomly allotted to three similar groups, ten lambs in each, to study the benefit of commercial feed additives Tonilisat (Saccharomyces cerevisiae) and Roemin W2 (Lactobacillus acidophilus, Lactobacillus thermophilus, Bifidobacterium and Lactose) as growth promoters on lambs performance, digestibility, rumen activity and some blood constituents. The experiment lasted about 107 days. Three experimental groups were allotted as control group: received the basal ration, T1 group: received the basal ration supplemented with Tonilisat as (0.5kg/ ton concentrate feed mixture) and T2 group: received the basal ration supplemented with Roemin W2 (1kg/ ton concentrate feed mixture). Our study revealed that addition of Tonilisat significantly increased digestion coefficient of crude protein than that of the control group, Furthermore, the supplementation of Tonilisat or Roemin W2 increased (p
Abstract: Wireless capsule Endoscopy (WCE) has rapidly
shown its wide applications in medical domain last ten years
thanks to its noninvasiveness for patients and support for thorough
inspection through a patient-s entire digestive system including
small intestine. However, one of the main barriers to efficient
clinical inspection procedure is that it requires large amount of
effort for clinicians to inspect huge data collected during the
examination, i.e., over 55,000 frames in video. In this paper, we
propose a method to compute meaningful motion changes of
WCE by analyzing the obtained video frames based on regional
optical flow estimations. The computed motion vectors are used to
remove duplicate video frames caused by WCE-s imaging nature,
such as repetitive forward-backward motions from peristaltic
movements. The motion vectors are derived by calculating
directional component vectors in four local regions. Our
experiments are performed on small intestine area, which is of
main interest to clinical experts when using WCEs, and our
experimental results show significant frame reductions comparing
with a simple frame-to-frame similarity-based image reduction
method.
Abstract: This paper describes the design considerations of an
experimental setup for research and exploring the drives of batteryfed
electric vehicles. Effective setup composition and its components
are discussed. With experimental setup described in this paper,
durability and functional tests can be procured to the customers.
Multiple experiments are performed in the form of steady-state
system exploring, acceleration programs, multi-step tests (speed
control, torque control), load collectives or close-to-reality driving
tests (driving simulation). Main focus of the functional testing is on
the measurements of power and energy efficiency and investigations
in driving simulation mode, which are used for application purposes.
In order to enable the examination of the drive trains beyond
standard modes of operation, different other parameters can be
studied also.
Abstract: In this research, heat transfer of a poly Ethylene
fluidized bed reactor without reaction were studied experimentally
and computationally at different superficial gas velocities. A multifluid
Eulerian computational model incorporating the kinetic theory
for solid particles was developed and used to simulate the heat
conducting gas–solid flows in a fluidized bed configuration.
Momentum exchange coefficients were evaluated using the Syamlal–
O-Brien drag functions. Temperature distributions of different phases
in the reactor were also computed. Good agreement was found
between the model predictions and the experimentally obtained data
for the bed expansion ratio as well as the qualitative gas–solid flow
patterns. The simulation and experimental results showed that the gas
temperature decreases as it moves upward in the reactor, while the
solid particle temperature increases. Pressure drop and temperature
distribution predicted by the simulations were in good agreement
with the experimental measurements at superficial gas velocities
higher than the minimum fluidization velocity. Also, the predicted
time-average local voidage profiles were in reasonable agreement
with the experimental results. The study showed that the
computational model was capable of predicting the heat transfer and
the hydrodynamic behavior of gas-solid fluidized bed flows with
reasonable accuracy.
Abstract: With the explosive growth of information sources available on the World Wide Web, it has become increasingly difficult to identify the relevant pieces of information, since web pages are often cluttered with irrelevant content like advertisements, navigation-panels, copyright notices etc., surrounding the main content of the web page. Hence, tools for the mining of data regions, data records and data items need to be developed in order to provide value-added services. Currently available automatic techniques to mine data regions from web pages are still unsatisfactory because of their poor performance and tag-dependence. In this paper a novel method to extract data items from the web pages automatically is proposed. It comprises of two steps: (1) Identification and Extraction of the data regions based on visual clues information. (2) Identification of data records and extraction of data items from a data region. For step1, a novel and more effective method is proposed based on visual clues, which finds the data regions formed by all types of tags using visual clues. For step2 a more effective method namely, Extraction of Data Items from web Pages (EDIP), is adopted to mine data items. The EDIP technique is a list-based approach in which the list is a linear data structure. The proposed technique is able to mine the non-contiguous data records and can correctly identify data regions, irrespective of the type of tag in which it is bound. Our experimental results show that the proposed technique performs better than the existing techniques.
Abstract: In this paper, the solubility of CO2 in AMP solution
have been measured at temperature range of ( 293, 303 ,313,323)
K.The amine concentration ranges studied are (2.0, 2.8, and 3.4) M.
A solubility apparatus was used to measure the solubility of CO2 in
AMP solution on samples of flue gases from Thermal and Central
Power Plants of Esfahan Steel Company. The modified Kent
Eisenberg model was used to correlate and predict the vapor-liquid
equilibria of the (CO2 + AMP + H2O) system. The model predicted
results are in good agreement with the experimental vapor-liquid
equilibrium measurements.