Abstract: In this research the level of mercury is analyzed in
muscle tissue of Otolithes ruber retailed in Hamedan, Iran were
determined by flame atomic absorption spectrometry after wet
digestion. Analysis of mercury was carried out by
spectrophotometrically. The average concentration of Hg in muscle
tissue of Otolithes ruber was 0.030±0.026 -g/g so lower than to
compare with the Maximum Allowable Concentration determined by
FAO/WHO Codex Alimentarius Commission.
Abstract: The principal focus of this study is on the
measurement and analysis of labor learnings in Pakistan. The study
at the aggregate economy level focus on the labor productivity
movements and at large-scale manufacturing level focus on the cost
structure, with isolating the contribution of the learning curve. The
analysis of S-shaped curve suggests that learnings are only below one
half of aggregate learning curve and other half shows the retardation
in learning, hence retardation in productivity movements. The study
implies the existence of learning economies in term of cost reduction
that is input cost per unit produced decreases by 0.51 percent every
time the cumulative production output doubles.
Abstract: This paper tries to represent a new method for
computing the reliability of a system which is arranged in series or
parallel model. In this method we estimate life distribution function
of whole structure using the asymptotic Extreme Value (EV)
distribution of Type I, or Gumbel theory. We use EV distribution in
minimal mode, for estimate the life distribution function of series
structure and maximal mode for parallel system. All parameters also
are estimated by Moments method. Reliability function and failure
(hazard) rate and p-th percentile point of each function are
determined. Other important indexes such as Mean Time to Failure
(MTTF), Mean Time to repair (MTTR), for non-repairable and
renewal systems in both of series and parallel structure will be
computed.
Abstract: We see in the present day scenario that the Global
positioning system (GPS) has been an effective tool to track the
vehicle. However the adverse part of it is that it can only track a
vehicle-s position. Our present work provides a better platform to
track and disable a vehicle using wireless technology. In our system
we embed a microcomputer which monitors the series of automotive
systems like engine, fuel and braking system. The external USB
modem is connected with the microcomputer to provide 24 x 7
internet accesses. The microcomputer is synchronized with the
owner-s multimedia mobile by means of a software tool “REMOTE
DESKTOP". A unique username and password is provided to the
software tool, so that the owner can only access the microcomputer
through the internet on owner-s mobile. The key fact is that our
design is placed such that it is known only to the owner.
Abstract: This paper presents a new method for the
implementation of a direct rotor flux control (DRFOC) of induction
motor (IM) drives. It is based on the rotor flux components
regulation. The d and q axis rotor flux components feed proportional
integral (PI) controllers. The outputs of which are the target stator
voltages (vdsref and vqsref). While, the synchronous speed is depicted at
the output of rotor speed controller. In order to accomplish variable
speed operation, conventional PI like controller is commonly used.
These controllers provide limited good performances over a wide
range of operations even under ideal field oriented conditions. An
alternate approach is to use the so called fuzzy logic controller. The
overall investigated system is implemented using dSpace system
based on digital signal processor (DSP). Simulation and experimental
results have been presented for a one kw IM drives to confirm the
validity of the proposed algorithms.
Abstract: In this paper variation of spot price and total profits of
the generating companies- through wholesale electricity trading are
discussed with and without Central Generating Stations (CGS) share
and seasonal variations are also considered. It demonstrates how
proper analysis of generators- efficiencies and capabilities, types of
generators owned, fuel costs, transmission losses and settling price
variation using the solutions of Optimal Power Flow (OPF), can
allow companies to maximize overall revenue. It illustrates how
solutions of OPF can be used to maximize companies- revenue under
different scenarios. And is also extended to computation of Available
Transfer Capability (ATC) is very important to the transmission
system security and market forecasting. From these results it is
observed that how crucial it is for companies to plan their daily
operations and is certainly useful in an online environment of
deregulated power system. In this paper above tasks are demonstrated
on 124 bus real-life Indian utility power system of Andhra Pradesh
State Grid and results have been presented and analyzed.
Abstract: The direct implementation of interleaver functions
in WiMAX is not hardware efficient due to presence of complex
functions. Also the conventional method i.e. using memories for
storing the permutation tables is silicon consuming. This work
presents a 2-D transformation for WiMAX channel interleaver
functions which reduces the overall hardware complexity to
compute the interleaver addresses on the fly. A fully reconfigurable
architecture for address generation in WiMAX
channel interleaver is presented, which consume 1.1 k-gates in
total. It can be configured for any block size and any modulation
scheme in WiMAX. The presented architecture can run at a
frequency of 200 MHz, thus fully supporting high bandwidth
requirements for WiMAX.
Abstract: A new design of a planar passive T-micromixer with fin-shaped baffles in the mixing channel is presented. The mixing efficiency and the level of pressure loss in the channel have been investigated by numerical simulations in the range of Reynolds number (Re) 1 to 50. A Mixing index (Mi) has been defined to quantify the mixing efficiency, which results over 85% at both ends of the Re range, what demonstrates the micromixer can enhance mixing using the mechanisms of diffusion (lower Re) and convection (higher Re). Three geometric dimensions: radius of baffle, baffles pitch and height of the channel define the design parameters, and the mixing index and pressure loss are the performance parameters used to optimize the micromixer geometry with a multi-criteria optimization method. The Pareto front of designs with the optimum trade-offs, maximum mixing index with minimum pressure loss, is obtained. Experiments for qualitative and quantitative validation have been implemented.
Abstract: In this paper we present a new multichannel high
voltage driver box to connect up to six MOEMS mirror devices to it that have resonant and also quasistatically driven actuating electrodes. It is possible to drive all resonant axes synchronously
while the amplitude of them can individually be controlled by separate microcontrollers that also operate the quasistatic axes.
Circuit simulations are compared with the measurements done on the
real system and also show the robust driving performance of a
MOEMS mirror.
Abstract: The symmetric solution set Σ sym is the set of all solutions to the linear systems Ax = b, where A is symmetric and lies between some given bounds A and A, and b lies between b and b. We present a contractor for Σ sym, which is an iterative method that starts with some initial enclosure of Σ sym (by means of a cartesian product of intervals) and sequentially makes the enclosure tighter. Our contractor is based on polyhedral approximation and solving a series of linear programs. Even though it does not converge to the optimal bounds in general, it may significantly reduce the overestimation. The efficiency is discussed by a number of numerical experiments.
Abstract: RF performance of SOI CMOS device has attracted
significant amount of interest recently. In order to improve RF
parameters, Strained Si/Relaxed Si0.8Ge0.2 investigated as a
replacement for Si technology .Enhancement of carrier mobility
associated with strain engineering makes Strained Si a promising
candidate for improving RF performance of CMOS technology.
From the simulation, the cut-off frequency is estimated to be 224
GHZ, whereas in SOI at similar bias is about 188 GHZ. Therefore,
Strained Si exhibits 19% improvement in cut-off frequency over
similar Si counterpart. In this paper, Ion/Ioff ratio is studied as one of
the key parameters in logic and digital application. Strained Si/SiGe
demonstrates better Ion/Ioff characteristic than SOI, in similar channel
length of 100 nm.Another important key analog figures of merit such
as Early Voltage (VEA) ,transconductance vs drain current (gm /Ids)
are studied. They introduce the efficiency of the devices to convert
dc power into ac frequency.
Abstract: The operation performance of a valveless micro-pump
is strongly dependent on the shape of connected nozzle/diffuser and
Reynolds number. The aims of present work are to compare the
performance curves of micropump with the original straight
nozzle/diffuser and contoured nozzle/diffuser under different back
pressure conditions. The tested valveless micropumps are assembled
of five pieces of patterned PMMA plates with hot-embracing
technique. The structures of central chamber, the inlet/outlet
reservoirs and the connected nozzle/diffuser are fabricated with laser
cutting machine. The micropump is actuated with circular-type PZT
film embraced on the bottom of central chamber. The deformation of
PZT membrane with various input voltages is measured with a
displacement laser probe. A simple testing facility is also constructed
to evaluate the performance curves for comparison.
In order to observe the evaluation of low Reynolds number
multiple vortex flow patterns within the micropump during suction
and pumping modes, the unsteady, incompressible laminar
three-dimensional Reynolds-averaged Navier-Stokes equations are
solved. The working fluid is DI water with constant thermo-physical
properties. The oscillating behavior of PZT film is modeled with the
moving boundary wall in way of UDF program. With the dynamic
mesh method, the instants pressure and velocity fields are obtained
and discussed.Results indicated that the volume flow rate is not
monotony increased with the oscillating frequency of PZT film,
regardless of the shapes of nozzle/diffuser. The present micropump
can generate the maximum volume flow rate of 13.53 ml/min when
the operation frequency is 64Hz and the input voltage is 140 volts.
The micropump with contoured nozzle/diffuser can provide 7ml/min
flow rate even when the back pressure is up to 400 mm-H2O. CFD
results revealed that the flow central chamber was occupied with
multiple pairs of counter-rotating vortices during suction and
pumping modes. The net volume flow rate over a complete
oscillating periodic of PZT
Abstract: In this paper we present a novel approach for human
Body configuration based on the Silhouette. We propose to address
this problem under the Bayesian framework. We use an effective
Model based MCMC (Markov Chain Monte Carlo) method to solve
the configuration problem, in which the best configuration could be
defined as MAP (maximize a posteriori probability) in Bayesian
model. This model based MCMC utilizes the human body model to
drive the MCMC sampling from the solution space. It converses the
original high dimension space into a restricted sub-space constructed
by the human model and uses a hybrid sampling algorithm. We
choose an explicit human model and carefully select the likelihood
functions to represent the best configuration solution. The
experiments show that this method could get an accurate
configuration and timesaving for different human from multi-views.
Abstract: This paper reports work done to improve the modeling of complex processes when only small experimental data sets are available. Neural networks are used to capture the nonlinear underlying phenomena contained in the data set and to partly eliminate the burden of having to specify completely the structure of the model. Two different types of neural networks were used for the application of pulping problem. A three layer feed forward neural networks, using the Preconditioned Conjugate Gradient (PCG) methods were used in this investigation. Preconditioning is a method to improve convergence by lowering the condition number and increasing the eigenvalues clustering. The idea is to solve the modified odified problem M-1 Ax= M-1b where M is a positive-definite preconditioner that is closely related to A. We mainly focused on Preconditioned Conjugate Gradient- based training methods which originated from optimization theory, namely Preconditioned Conjugate Gradient with Fletcher-Reeves Update (PCGF), Preconditioned Conjugate Gradient with Polak-Ribiere Update (PCGP) and Preconditioned Conjugate Gradient with Powell-Beale Restarts (PCGB). The behavior of the PCG methods in the simulations proved to be robust against phenomenon such as oscillations due to large step size.
Abstract: We have measured the pressure drop and convective
heat transfer coefficient of water – based AL(25nm),AL2O3(30nm)
and CuO(50nm) Nanofluids flowing through a uniform heated
circular tube in the fully developed laminar flow regime. The
experimental results show that the data for Nanofluids friction factor
show a good agreement with analytical prediction from the Darcy's
equation for single-phase flow. After reducing the experimental
results to the form of Reynolds, Rayleigh and Nusselt numbers. The
results show the local Nusselt number and temperature have
distribution with the non-dimensional axial distance from the tube
entry. Study decided that thenNanofluid as Newtonian fluids through
the design of the linear relationship between shear stress and the rate
of stress has been the study of three chains of the Nanofluid with
different concentrations and where the AL, AL2O3 and CuO – water
ranging from (0.25 - 2.5 vol %). In addition to measuring the four
properties of the Nanofluid in practice so as to ensure the validity of
equations of properties developed by the researchers in this area and
these properties is viscosity, specific heat, and density and found that
the difference does not exceed 3.5% for the experimental equations
between them and the practical. The study also demonstrated that the
amount of the increase in heat transfer coefficient for three types of
Nano fluid is AL, AL2O3, and CuO – Water and these ratios are
respectively (45%, 32%, 25%) with insulation and without insulation
(36%, 23%, 19%), and the statement of any of the cases the best
increase in heat transfer has been proven that using insulation is
better than not using it. I have been using three types of Nano
particles and one metallic Nanoparticle and two oxide Nanoparticle
and a statement, whichever gives the best increase in heat transfer.
Abstract: This paper presents an advance in monitoring and
process control of surface roughness in CNC machine for the turning
and milling processes. An integration of the in-process monitoring
and process control of the surface roughness is proposed and
developed during the machining process by using the cutting force
ratio. The previously developed surface roughness models for turning
and milling processes of the author are adopted to predict the inprocess
surface roughness, which consist of the cutting speed, the
feed rate, the tool nose radius, the depth of cut, the rake angle, and
the cutting force ratio. The cutting force ratios obtained from the
turning and the milling are utilized to estimate the in-process surface
roughness. The dynamometers are installed on the tool turret of CNC
turning machine and the table of 5-axis machining center to monitor
the cutting forces. The in-process control of the surface roughness
has been developed and proposed to control the predicted surface
roughness. It has been proved by the cutting tests that the proposed
integration system of the in-process monitoring and the process
control can be used to check the surface roughness during the cutting
by utilizing the cutting force ratio.
Abstract: In any distributed systems, process scheduling plays a
vital role in determining the efficiency of the system. Process scheduling algorithms are used to ensure that the components of the
system would be able to maximize its utilization and able to complete all the processes assigned in a specified period of time.
This paper focuses on the development of comparative simulator for distributed process scheduling algorithms. The objectives of the works that have been carried out include the development of the
comparative simulator, as well as to implement a comparative study
between three distributed process scheduling algorithms; senderinitiated,
receiver-initiated and hybrid sender-receiver-initiated
algorithms. The comparative study was done based on the Average Waiting Time (AWT) and Average Turnaround Time (ATT) of the
processes involved. The simulation results show that the performance of the algorithms depends on the number of nodes in the system.
Abstract: In Korea, the technology of a load fo nuclear power plant has been being developed.
automatic controller which is able to control temperature and axial power distribution was developed. identification algorithm and a model predictive contact former transforms the nuclear reactor status into
numerically. And the latter uses them and ge
manipulated values such as two kinds of control ro
this automatic controller, the performance of a coperation was evaluated. As a result, the automatic generated model parameters of a nuclear react to nuclear reactor average temperature and axial power the desired targets during a daily load follow.
Abstract: Recent years have seen a growing trend towards the
integration of multiple information sources to support large-scale
prediction of protein-protein interaction (PPI) networks in model
organisms. Despite advances in computational approaches, the
combination of multiple “omic" datasets representing the same type
of data, e.g. different gene expression datasets, has not been
rigorously studied. Furthermore, there is a need to further investigate
the inference capability of powerful approaches, such as fullyconnected
Bayesian networks, in the context of the prediction of PPI
networks. This paper addresses these limitations by proposing a
Bayesian approach to integrate multiple datasets, some of which
encode the same type of “omic" data to support the identification of
PPI networks. The case study reported involved the combination of
three gene expression datasets relevant to human heart failure (HF).
In comparison with two traditional methods, Naive Bayesian and
maximum likelihood ratio approaches, the proposed technique can
accurately identify known PPI and can be applied to infer potentially
novel interactions.
Abstract: The spatial variation in plant species associated with intercropping is intended to reduce resource competition between species and increase yield potential. A field experiment was carried out on corn (Zea mays L.) and soybean (Glycine max L.) intercropping in a replacement series experiment with weed contamination consist of: weed free, infestation of redroot pigweed, infestation of jimsonweed and simultaneous infestation of redroot pigweed and jimsonweed in Karaj, Iran during 2007 growing season. The experimental design was a randomized complete block in factorial experiment with replicated thrice. Significant (P≤0.05) differences were observed in yield in intercropping. Corn yield was higher in intercropping, but soybean yield was significantly reduced by corn when intercropped. However, total productivity and land use efficiency were high under the intercropping system even in contamination of either species of weeds. Aggressivity of corn relative to soybean revealed the greater competitive ability of corn than soybean. Land equivalent ratio (LER) more than 1 in all treatments attributed to intercropping advantages and was highest in 50: 50 (corn/soybean) in weed free. These findings suggest that intercropping corn and soybean increase total productivity per unit area and improve land use efficiency. Considering the experimental findings, corn-soybean intercropping (50:50) may be recommended for yield advantage, more efficient utilization of resources, and weed suppression as a biological control.