Abstract: Discourse pronominal anaphora resolution must be part of any efficient information processing systems, since the reference of a pronoun is dependent on an antecedent located in the discourse. Contrary to knowledge-poor approaches, this paper shows that syntax-semantic relations are basic in pronominal anaphora resolution. The identification of quantified expressions to which pronouns can be anaphorically related provides further evidence that pronominal anaphora is based on domains of interpretation where asymmetric agreement holds.
Abstract: Applying corona wind as a novel technique can lead
to a great level of heat and mass transfer augmentation by using very
small amount of energy. Enhancement of forced flow evaporation
rate by applying electric field (corona wind) has been experimentally
evaluated in this study. Corona wind produced by a fine wire
electrode which is charged with positive high DC voltage impinges
to water surface and leads to evaporation enhancement by disturbing
the saturated air layer over water surface. The study was focused on
the effect of corona wind velocity, electrode spacing and air flow
velocity on the level of evaporation enhancement. Two sets of
experiments, i.e. with and without electric field, have been
conducted. Data obtained from the first experiment were used as
reference for evaluation of evaporation enhancement at the presence
of electric field. Applied voltages ranged from corona threshold
voltage to spark over voltage at 1 kV increments. The results showed
that corona wind has great enhancement effect on water evaporation
rate, but its effectiveness gradually diminishes by increasing air flow
velocity. Maximum enhancements were 7.3 and 3.6 for air velocities
of 0.125 and 1.75 m/s, respectively.
Abstract: Saddlepoint approximations is one of the tools to obtain
an expressions for densities and distribution functions. We approximate
the densities of the observed gaps between the hypopnea events
using the Huzurbazar saddlepoint approximation. We demonstrate the
density of a maximum likelihood estimator in exponential families.
Abstract: Partitions can play a significant role in minimising cochannel
interference of Wireless LANs by attenuating signals across
room boundaries. This could pave the way towards higher density
deployments in home and office environments through spatial
channel reuse. Yet, due to protocol limitations, the latest incantation
of IEEE 802.11 standard is still unable to take advantage of this fact:
Despite having clearly adequate Signal to Interference Ratio (SIR)
over co-channel neighbouring networks in other rooms, its goodput
falls significantly lower than its maximum in the absence of cochannel
interferers. In this paper, we describe how this situation can
be remedied via modest modifications to the standard.
Abstract: This study proposes a multi-response surface
optimization problem (MRSOP) for determining the proper choices
of a process parameter design (PPD) decision problem in a noisy
environment of a grease position process in an electronic industry.
The proposed models attempts to maximize dual process responses
on the mean of parts between failure on left and right processes. The
conventional modified simplex method and its hybridization of the
stochastic operator from the hunting search algorithm are applied to
determine the proper levels of controllable design parameters
affecting the quality performances. A numerical example
demonstrates the feasibility of applying the proposed model to the
PPD problem via two iterative methods. Its advantages are also
discussed. Numerical results demonstrate that the hybridization is
superior to the use of the conventional method. In this study, the
mean of parts between failure on left and right lines improve by
39.51%, approximately. All experimental data presented in this
research have been normalized to disguise actual performance
measures as raw data are considered to be confidential.
Abstract: Motor imagery classification provides an important basis for designing Brain Machine Interfaces [BMI]. A BMI captures and decodes brain EEG signals and transforms human thought into actions. The ability of an individual to control his EEG through imaginary mental tasks enables him to control devices through the BMI. This paper presents a method to design a four state BMI using EEG signals recorded from the C3 and C4 locations. Principle features extracted through principle component analysis of the segmented EEG are analyzed using two novel classification algorithms using Elman recurrent neural network and functional link neural network. Performance of both classifiers is evaluated using a particle swarm optimization training algorithm; results are also compared with the conventional back propagation training algorithm. EEG motor imagery recorded from two subjects is used in the offline analysis. From overall classification performance it is observed that the BP algorithm has higher average classification of 93.5%, while the PSO algorithm has better training time and maximum classification. The proposed methods promises to provide a useful alternative general procedure for motor imagery classification
Abstract: An edge based local search algorithm, called ELS, is proposed for the maximum clique problem (MCP), a well-known combinatorial optimization problem. ELS is a two phased local search method effectively £nds the near optimal solutions for the MCP. A parameter ’support’ of vertices de£ned in the ELS greatly reduces the more number of random selections among vertices and also the number of iterations and running times. Computational results on BHOSLIB and DIMACS benchmark graphs indicate that ELS is capable of achieving state-of-the-art-performance for the maximum clique with reasonable average running times.
Abstract: The fine structure of supercavitation in the wake of a
symmetrical cylinder is studied with high-speed video cameras. The
flow is observed in a cavitation tunnel at the speed of 8m/sec when the
sidewall and the wake are partially filled with the massive cavitation
bubbles. The present experiment observed that a two-dimensional
ripple wave with a wave length of 0.3mm is propagated in a
downstream direction, and then abruptly increases to a thicker
three-dimensional layer. IR-photography recorded that the wakes
originated from the horseshoe vortexes alongside the cylinder. The
wake was developed to inside the dead water zone, which absorbed the
bubbly wake propelled from the separated vortices at the center of the
cylinder. A remote sensing classification technique (maximum most
likelihood) determined that the surface porosity was 0.2, and the mean
speed in the mixed wake was 7m/sec. To confirm the existence of
two-dimensional wave motions in the interface, the experiments were
conducted at a very low frequency, and showed similar gravity waves
in both the upper and lower interfaces.
Abstract: Multi-user interference (MUI) is the main reason of system deterioration in the Spectral Amplitude Coding Optical Code Division Multiple Access (SAC-OCDMA) system. MUI increases with the number of simultaneous users, resulting into higher probability bit rate and limits the maximum number of simultaneous users. On the other hand, Phase induced intensity noise (PIIN) problem which is originated from spontaneous emission of broad band source from MUI severely limits the system performance should be addressed as well. Since the MUI is caused by the interference of simultaneous users, reducing the MUI value as small as possible is desirable. In this paper, an extensive study for the system performance specified by MUI and PIIN reducing is examined. Vectors Combinatorial (VC) codes families are adopted as a signature sequence for the performance analysis and a comparison with reported codes is performed. The results show that, when the received power increases, the PIIN noise for all the codes increases linearly. The results also show that the effect of PIIN can be minimized by increasing the code weight leads to preserve adequate signal to noise ratio over bit error probability. A comparison study between the proposed code and the existing codes such as Modified frequency hopping (MFH), Modified Quadratic- Congruence (MQC) has been carried out.
Abstract: The competitive learning is an adaptive process in
which the neurons in a neural network gradually become sensitive to
different input pattern clusters. The basic idea behind the Kohonen-s
Self-Organizing Feature Maps (SOFM) is competitive learning.
SOFM can generate mappings from high-dimensional signal spaces
to lower dimensional topological structures. The main features of this
kind of mappings are topology preserving, feature mappings and
probability distribution approximation of input patterns. To overcome
some limitations of SOFM, e.g., a fixed number of neural units and a
topology of fixed dimensionality, Growing Self-Organizing Neural
Network (GSONN) can be used. GSONN can change its topological
structure during learning. It grows by learning and shrinks by
forgetting. To speed up the training and convergence, a new variant
of GSONN, twin growing cell structures (TGCS) is presented here.
This paper first gives an introduction to competitive learning, SOFM
and its variants. Then, we discuss some GSONN with fixed
dimensionality, which include growing cell structures, its variants
and the author-s model: TGCS. It is ended with some testing results
comparison and conclusions.
Abstract: We constructed a method of phase unwrapping for a typical wave-front by utilizing the maximizer of the posterior marginal (MPM) estimate corresponding to equilibrium statistical mechanics of the three-state Ising model on a square lattice on the basis of an analogy between statistical mechanics and Bayesian inference. We investigated the static properties of an MPM estimate from a phase diagram using Monte Carlo simulation for a typical wave-front with synthetic aperture radar (SAR) interferometry. The simulations clarified that the surface-consistency conditions were useful for extending the phase where the MPM estimate was successful in phase unwrapping with a high degree of accuracy and that introducing prior information into the MPM estimate also made it possible to extend the phase under the constraint of the surface-consistency conditions with a high degree of accuracy. We also found that the MPM estimate could be used to reconstruct the original wave-fronts more smoothly, if we appropriately tuned hyper-parameters corresponding to temperature to utilize fluctuations around the MAP solution. Also, from the viewpoint of statistical mechanics of the Q-Ising model, we found that the MPM estimate was regarded as a method for searching the ground state by utilizing thermal fluctuations under the constraint of the surface-consistency condition.
Abstract: This research proposes a Preemptive Possibilistic
Linear Programming (PPLP) approach for solving multiobjective
Aggregate Production Planning (APP) problem with interval demand
and imprecise unit price and related operating costs. The proposed
approach attempts to maximize profit and minimize changes of
workforce. It transforms the total profit objective that has imprecise
information to three crisp objective functions, which are maximizing
the most possible value of profit, minimizing the risk of obtaining the
lower profit and maximizing the opportunity of obtaining the higher
profit. The change of workforce level objective is also converted.
Then, the problem is solved according to objective priorities. It is
easier than simultaneously solve the multiobjective problem as
performed in existing approach. Possible range of interval demand is
also used to increase flexibility of obtaining the better production
plan. A practical application of an electronic company is illustrated to
show the effectiveness of the proposed model.
Abstract: The aim of the study was to follow changes of powervelocity
relationship in female volleyball players during an annual
training cycle. The study was conducted on eleven female volleyball
players: age 21.6±1.7 years, body height 177.9±4.7 cm, body mass
71.3±6.6 kg and training experience 8.6±3.3 years. Power–velocity
relationship was determined from five maximal 10-second
cycloergometer efforts with external loads equal: 2.5, 5.0, 7.5, 10.0
and 12.5% of body weight (BW) before (I) and after (II) the
preparatory period, after the first (III) and second (IV) competitive
season. The maximal power output increased from 9.30±0.85 W•kg–1
(I) to 9.50±0.96 W•kg–1 (II), 9.77±0.96 W•kg–1 (III) and 9.95±1.13
W•kg–1 (IV, p
Abstract: In this paper we describe a hybrid technique of Minimax search and aggregate Mahalanobis distance function synthesis to evolve Awale game player. The hybrid technique helps to suggest a move in a short amount of time without looking into endgame database. However, the effectiveness of the technique is heavily dependent on the training dataset of the Awale strategies utilized. The evolved player was tested against Awale shareware program and the result is appealing.
Abstract: The present work presents a method of calculating the
ductility of rectangular sections of beams considering nonlinear
behavior of concrete and steel. This calculation procedure allows us
to trace the curvature of the section according to the bending
moment, and consequently deduce ductility. It also allowed us to
study the various parameters that affect the value of the ductility. A
comparison of the effect of maximum rates of tension steel, adopted
by the codes, ACI [1], EC8 [2] and RPA [3] on the value of the
ductility was made. It was concluded that the maximum rate of steels
permitted by the ACI [1] codes and RPA [3] are almost similar in
their effect on the ductility and too high. Therefore, the ductility
mobilized in case of an earthquake is low, the inverse of code EC8
[2]. Recommendations have been made in this direction.
Abstract: This paper presents the findings of an
experimental investigation to study the effect of alkali content
in geopolymer mortar specimens exposed to sulphuric acid.
Geopolymer mortar specimens were manufactured from Class F fly
ash by activation with a mixture of sodium hydroxide and sodium
silicate solution containing 5% to 8% Na2O. Durability of specimens
were assessed by immersing them in 10% sulphuric acid solution and
periodically monitoring surface deterioration and depth of
dealkalization, changes in weight and residual compressive strength
over a period of 24 weeks. Microstructural changes in the specimens
were studied with Scanning electron microscopy (SEM) and EDAX.
Alkali content in the activator solution significantly affects the
durability of fly ash based geopolymer mortars in sulphuric acid.
Specimens manufactured with higher alkali content performed better
than those manufactured with lower alkali content. After 24 weeks in
sulphuric acid, specimen with 8% alkali still recorded a residual
strength as high as 55%.
Abstract: We provide a maximum norm analysis of a finite
element Schwarz alternating method for a nonlinear elliptic boundary
value problem of the form -Δu = f(u), on two overlapping sub
domains with non matching grids. We consider a domain which is
the union of two overlapping sub domains where each sub domain
has its own independently generated grid. The two meshes being
mutually independent on the overlap region, a triangle belonging to
one triangulation does not necessarily belong to the other one. Under
a Lipschitz assumption on the nonlinearity, we establish, on each sub
domain, an optimal L∞ error estimate between the discrete Schwarz
sequence and the exact solution of the boundary value problem.
Abstract: Free convection effects and heat transfer due to a pulsating point heat source embedded in an infinite, fluid saturated, porous dusty medium are studied analytically. Both velocity and temperature fields are discussed in the form of series expansions in the Rayleigh number, for both the fluid and particle phases based on the mean heat generation rate from source and on the permeability of the porous dusty medium. This study is carried out by assuming the Rayleigh number small and the validity of Darcy-s law. Analytical expressions for both phases are obtained for second order mean in both velocity and temperature fields and evolution of different wave patterns are observed in the fluctuating part. It has been observed that, at the vicinity of the origin, the second order mean flow is influenced only by relaxation time of dust particles and not by dust concentration.
Abstract: Clustering is a very well known technique in data mining. One of the most widely used clustering techniques is the k-means algorithm. Solutions obtained from this technique are dependent on the initialization of cluster centers. In this article we propose a new algorithm to initialize the clusters. The proposed algorithm is based on finding a set of medians extracted from a dimension with maximum variance. The algorithm has been applied to different data sets and good results are obtained.
Abstract: A hardware efficient, multi mode, re-configurable
architecture of interleaver/de-interleaver for multiple standards,
like DVB, WiMAX and WLAN is presented. The interleavers
consume a large part of silicon area when implemented by using
conventional methods as they use memories to store permutation
patterns. In addition, different types of interleavers in different
standards cannot share the hardware due to different construction
methodologies. The novelty of the work presented in this paper is
threefold: 1) Mapping of vital types of interleavers including
convolutional interleaver onto a single architecture with flexibility
to change interleaver size; 2) Hardware complexity for channel
interleaving in WiMAX is reduced by using 2-D realization of the
interleaver functions; and 3) Silicon cost overheads reduced by
avoiding the use of small memories. The proposed architecture
consumes 0.18mm2 silicon area for 0.12μm process and can
operate at a frequency of 140 MHz. The reduced complexity helps
in minimizing the memory utilization, and at the same time
provides strong support to on-the-fly computation of permutation
patterns.