Abstract: An innovative flooring underlayment was produced
and tested. The composite system is made of common OSB boards
and a layer of eco-friendly non-cement gypsum based material
(GeoGypTM). It was found that the shear bond between the two
materials is sufficient to secure the composite interaction between the
two. The very high compressive strength and relatively high tensile
strength of the non-cement based component together with its high
modulus of elasticity provides enough strength and stiffness for the
composite product to cover wider spacing between the joists. The
initial findings of this study indicate that with joist spacing as wide as
800 mm, the flooring system provides enough strength without
compromising the serviceability requirements of the building codes.
Abstract: Scrubbing by a liquid spraying is one of the most
effective processes used for removal of fine particles and soluble
gas pollutants (such as SO2, HCl, HF) from the flue gas. There are
many configurations of scrubbers designed to provide contact
between the liquid and gas stream for effectively capturing
particles or soluble gas pollutants, such as spray plates, packed bed
towers, jet scrubbers, cyclones, vortex and venturi scrubbers. The
primary function of venturi scrubber is the capture of fine particles
as well as HCl, HF or SO2 removal with effect of the flue gas
temperature decrease before input to the absorption column. In this
paper, sulfur dioxide (SO2) from flue gas was captured using new
design replacing venturi scrubber (1st degree of wet scrubbing).
The flue gas was prepared by the combustion of the carbon
disulfide solution in toluene (1:1 vol.) in the flame in the reactor.
Such prepared flue gas with temperature around 150°C was
processed in designed laboratory O-element scrubber. Water was
used as absorbent liquid. The efficiency of SO2 removal, pressure
drop and temperature drop were measured on our experimental
device. The dependence of these variables on liquid-gas ratio was
observed. The average temperature drop was in the range from
150°C to 40°C. The pressure drop was increased with increasing of
a liquid-gas ratio, but no too much as for the common venturi
scrubber designs. The efficiency of SO2 removal was up to 70 %.
The pressure drop of our new designed wet scrubber is similar to
commonly used venturi scrubbers; nevertheless the influence of
amount of the liquid on pressure drop is not so significant.
Abstract: We investigate relaxation dynamics of a quantum
dipole emitter (QDE), e.g., a molecule or quantum dot, located near a
metal nanoparticle (MNP) exhibiting a dipolar localized surface
plasmon (LSP) resonance at the frequency of the QDE radiative
transition. It is shown that under the condition of the QDE-MNP
characteristic relaxation time being much shorter than that of the
QDE in free-space but much longer than the LSP lifetime. It is also
shown that energy dissipation in the QDE-MNP system is relatively
weak with the probability of the photon emission being about 0.75, a
number which, rather surprisingly, does not explicitly depend on the
metal absorption characteristics. The degree of entanglement
measured by the concurrency takes the maximum value, while the
distances between the QDEs and metal ball approximately are equal.
Abstract: This paper presents a model for a modified T-junction
device for microspheres generation. The numerical model is
developed using a commercial software package: COMSOL
Multiphysics. In order to test the accuracy of the numerical model,
multiple variables, such as the flow rate of cross-flow, fluid properties,
structure, and geometry of the microdevice are applied. The results
from the model are compared with the experimental results in the
diameter of the microsphere generated. The comparison shows a good
agreement. Therefore the model is useful in further optimization of the
device and feedback control of microsphere generation if any.
Abstract: This study investigates the suitability of using plastic,
such as polyethylene terephthalate (PET), as a partial replacement of
natural coarse and fine aggregates (for example, brick chips and
natural sand) to produce lightweight concrete for load bearing
structural members. The plastic coarse aggregate (PCA) and plastic
fine aggregate (PFA) were produced from melted polyethylene
terephthalate (PET) bottles. Tests were conducted using three
different water–cement (w/c) ratios, such as 0.42, 0.48, and 0.57,
where PCA and PFA were used as 50% replacement of coarse and
fine aggregate respectively. Fresh and hardened properties of
concrete have been compared for natural aggregate concrete (NAC),
PCA concrete (PCC) and PFA concrete (PFC). The compressive
strength of concrete at 28 days varied with the water–cement ratio for
both the PCC and PFC. Between PCC and PFC, PFA concrete
showed the highest compressive strength (23.7 MPa) at 0.42 w/c ratio
and also the lowest compressive strength (13.7 MPa) at 0.57 w/c
ratio. Significant reduction in concrete density was mostly observed
for PCC samples, ranging between 1977–1924 kg/m³. With the
increase in water–cement ratio PCC achieved higher workability
compare to both NAC and PFC. It was found that both the PCA and
PFA contained concrete achieved the required compressive strength
to be used for structural purpose as partial replacement of the natural
aggregate; but to obtain the desired lower density as lightweight
concrete the PCA is most suited.
Abstract: The quality and condition of perishable products
delivered to the market and their subsequent selling prices are
directly affected by the care taken during harvesting and handling.
Mechanical injury, in fact, occurs at all stages, from pre-harvest
operations through post-harvest handling, packing and transport to
the market. The main implications of this damage are the reduction of
the product’s quality and economical losses related to the shelf life
diminution. For most perishable products, the shelf life is relatively
short and it is typically dictated by microbial growth related to the
application of dynamic and static loads during transportation. This
paper presents the correlation between vibration levels and
microbiological growth on strawberries and woodland strawberries
and detects the presence of volatile organic compounds (VOC) in
order to develop an intelligent logistic unit capable of monitoring
VOCs using a specific sensor system. Fresh fruits were exposed to
vibrations by means of a vibrating table in a temperature-controlled
environment. Microbiological analyses were conducted on samples,
taken at different positions along the column of the crates. The values
obtained were compared with control samples not exposed to
vibrations and the results show that different positions along the
column influence the development of bacteria, yeasts and filamentous
fungi.
Abstract: In this article, the antibiogram and heavy metal
resistance profile of the bacteria isolated from total 34 studied
animals (Pelophylax ridibundus = 12; Mauremys rivulata = 14;
Natrix natrix = 8) captured around the Biga Stream, are described.
There was no database information on antibiogram and heavy metal
resistance profile of bacteria from these area’s amphibians and
reptiles.
A total of 200 bacteria were successfully isolated from cloaca and
oral samples of the aquatic amphibians and reptiles as well as from
the water sample. According to Jaccard’s similarity index, the degree
of similarity in the bacterial flora was quite high among the
amphibian and reptile species under examination, whereas it was
different from the bacterial diversity in the water sample. The most
frequent isolates were A. hydrophila (31.5%), B. pseudomallei
(8.5%), and C. freundii (7%). The total numbers of bacteria obtained
were as follows: 45 in P. ridibundus, 45 in N. natrix 30 in M.
rivulata, and 80 in the water sample. The result showed that
cefmetazole was the most effective antibiotic to control the bacteria
isolated in this study and that approximately 93.33% of the bacterial
isolates were sensitive to this antibiotic. The multiple antibiotic
resistances (MAR) index indicated that P. ridibundus (0.95) > N.
natrix (0.89) > M. rivulata (0.39). Furthermore, all the tested heavy
metals (Pb+2, Cu+2, Cr+3, and Mn+2) inhibit the growth of the bacterial
isolates at different rates. Therefore, it indicated that the water source
of the animals was contaminated with both antibiotic residues and
heavy metals.
Abstract: Optical radiation emitted from a metal-coated fiber tip apex at liquid-air interface was measured. The intensity of the output radiation was strongly depend on the relative position of the tip to a liquid-air interface and varied with surface fluctuations. This phenomenon permits in-situ real-time investigation of nano-metric vibrations of the liquid surface and provides a basis for development of various origin ultrasensitive vibration detecting sensors. The described method can be used for detection of week seismic vibrations.
Abstract: Reliability allocation is quite important during early
design and development stages for a system to apportion its specified
reliability goal to subsystems. This paper improves the reliability
fuzzy allocation method, and gives concrete processes on determining
the factor and sub-factor sets, weight sets, judgment set, and
multi-stage fuzzy evaluation. To determine the weight of factor and
sub-factor sets, the modified trapezoidal numbers are proposed to
reduce errors caused by subjective factors. To decrease the fuzziness
in fuzzy division, an approximation method based on linear
programming is employed. To compute the explicit values of fuzzy
numbers, centroid method of defuzzification is considered. An
example is provided to illustrate the application of the proposed
reliability allocation method based on fuzzy arithmetic.
Abstract: Taiwan is a hyper endemic area for the Hepatitis B
virus (HBV). The estimated total number of HBsAg carriers in the
general population who are more than 20 years old is more than 3
million. Therefore, a case record review is conducted from January
2003 to June 2007 for all patients with a diagnosis of acute hepatitis
who were admitted to the Emergency Department (ED) of a
well-known teaching hospital. The cost for the use of medical
resources is defined as the total medical fee. In this study, principal
component analysis (PCA) is firstly employed to reduce the number of
dimensions. Support vector regression (SVR) and artificial neural
network (ANN) are then used to develop the forecasting model. A total
of 117 patients meet the inclusion criteria. 61% patients involved in
this study are hepatitis B related. The computational result shows that
the proposed PCA-SVR model has superior performance than other
compared algorithms. In conclusion, the Child-Pugh score and
echogram can both be used to predict the cost of medical resources for
patients with acute hepatitis in the ED.
Abstract: The number of persons with implanted cardiac
pacemakers (PM) has increased in Western countries. The aim of this
paper is to investigate the possible situations where persons with a
PM may be exposed to extremely low frequency (ELF) electric (EF)
and magnetic fields (MF) that may disturb their PM. Based on our
earlier studies, it is possible to find such high public exposure to EFs
only in some places near 400 kV power lines, where an EF may
disturb a PM in unipolar mode. Such EFs cannot be found near 110
kV power lines. Disturbing MFs can be found near welding
machines. However, we do not have measurement data from welding.
Based on literature and earlier studies at Tampere University of
Technology, it is difficult to find public EF or MF exposure that is
high enough to interfere with PMs.
Abstract: In 2010-2011, the research on zooplankton was
conducted in the southern part of the Baltic Sea to determine seasonal
variability in changes occurring throughout the zooplankton in 2010
and 2011, both in the region of Gdańsk Deep, and in the western part
of Gdańsk Bay. The research in the sea showed that the taxonomic
composition of holoplankton in the southern part of the Baltic Sea
was similar to that recorded in this region for many years. The
maximum values of abundance and biomass of zooplankton both in
the Deep and the Bay of Gdańsk were observed in the summer
season. Copepoda dominated in the composition of zooplankton for
almost the entire study period, while rotifers occurred in larger
numbers only in the summer 2010 in the Gdańsk Deep as well as in
May and July 2010 in the western part of Gdańsk Bay, and
meroplankton – in April 2011.
Abstract: Feed oil samples which are used as mixed feed raw
material were taken from six different feed factories in March, May
and July. All factories make production in Konya, Turkey and all of
the samples were crude soybean oils. Physical and chemical analyses,
free radical scavenger effect, and total phenol content were
determined on these oil samples. Moisture (M) content was found
between 0.10-22.23%, saponification number (SF) was determined
143.13 to 167.93 KOH/kg, free fatty acidity (FFA) was varied 0.73 to
35.00%, peroxide value (PV) was found between 1.53 and 28.43
meq/kg, unsaponifiable matter (USM) was determined from 0.40 to
17.10%, viscosity (V) was found between 34.30 and 625.67 mPas,
sediment (S) amount was determined between 0.60-18.16%, free
radical scavenger effect (FRSE) was varied 20.7 to 43.04% inhibition
of the extract and total phenol (TPC) content was found between 1.20
and 2.69mg/L extract. Different results were found between months
and factories.
Abstract: In this paper, the effects of fiber types and elevated
temperatures on compressive strength, modulus of rapture and the
bond characteristics of fiber reinforced concretes (FRC) are
presented. By using the three different types of fibers (steel fiber-SF,
polypropylene-PPF and polyvinyl alcohol-PVA), FRC specimens
were produced and exposed to elevated temperatures up to 800 ºC for
1.5 hours. In addition, a plain concrete (without fiber) was produced
and used as a control. Test results obtained showed that the steel fiber
reinforced concrete (SFRC) had the highest compressive strength,
modulus of rapture and bond stress values at room temperatures, the
residual bond, flexural and compressive strengths of both FRC and
plain concrete dropped sharply after exposure to high temperatures.
The results also indicated that the reduction of bond, flexural and
compressive strengths with increasing the exposed temperature was
relatively less for SFRC than for plain, and FRC with PPF and PVA.
Abstract: The aim of this paper is to present the optimization
methodology developed in the frame of a Coastal Transport
Information System. The system will be used for the effective design
of coastal transportation lines and incorporates subsystems that
implement models, tools and techniques that may support the design
of improved networks. The role of the optimization and decision
subsystem is to provide the user with better and optimal scenarios
that will best fulfill any constrains, goals or requirements posed. The
complexity of the problem and the large number of parameters and
objectives involved led to the adoption of an evolutionary method
(Genetic Algorithms). The problem model and the subsystem
structure are presented in detail, and, its support for simulation is also
discussed.
Abstract: Verification of vented wooden façade system with
bonded joints is presented in this paper. The potential of bonded
joints is studied and described in more detail. The paper presents the results of an experimental and theoretical research about the effects of freeze cycling on the bonded joint. For the purpose of tests spruce
timber profiles were chosen for the load bearing substructure. Planks from wooden plastic composite and Siberian larch are representing facade cladding. Two types of industrial polyurethane adhesives intended for structural bonding were selected. The article is focused on the preparation as well as on the subsequent curing and conditioning of test samples. All test samples were subjected to 15 cycles that represents sudden temperature changes, i.e. immersion in a water bath at (293.15 ± 3) K for 6 hours and subsequent freezing to (253.15 ± 2) K for 18 hours. Furthermore, the retention of bond strength between substructure and cladding wastested and strength in shear was determined under tensile stress.Research data indicate that little, if any, damage to the bond results from freezingcycles. Additionally, the suitability of selected group of adhesives in combination with timber substructure was confirmed.
Abstract: Taking into account the significance of measuring the
daily use of the study space in the libraries in order to develop and
reorganize the space for enhancing the efficiency of the study space,
the current study aimed to apply GIS in analyzing the study halls of
the Central Library and Document Center of Tehran University in
order to determine how study desks and chairs were used by the
students. The study used a combination of survey-descriptive and
system design method. In order to gather the required data, surveydescriptive
method was used. For implementing and entering data
into ArcGIS and analyzing the data and displaying the results on the
maps of the study halls of the library, system design method was
utilized. The design of the spatial database of the use of the study
halls was measured through the extent of occupancy of the space by
the library users and the maps of the study halls of the central library
of Tehran University as the case study. The results showed that
Abooreyhan hall had the highest rate of occupancy of the desks and
chairs compared to the other halls. The Hall of Science and
Technology, with an average occupancy rate of 0.39 for the tables
represented the lowest number of users and Rashid al-Dins hall, and
Science and Technology hall with an average occupancy rate (0.40)
had the lowest number of users for seats. In this study, the
comparison of the space occupied at different periods in the morning,
evenings, afternoons, and several months was performed through
GIS. This system analyzed the space relationships effectively and
efficiently. The output of this study would be used by administrators
and librarians to determine the exact extent of use of the equipment
of the study halls and librarians can use the output map to design the
space more efficiently at the library.
Abstract: Nanofibers of PVA /nickel nitrate/silica/alumina
izopropoxide/boric acid composite were prepared by using sol-gel
processing and electrospinning technique. By high temperature
calcinations of the above precursor fibers, nanofibers of
NiO/Al2O3/B2O3/SiO2 composite with diameters about 500 nm
could be successfully obtained. The fibers were characterized by
XRD and SEM analyses.
Abstract: The paper presents an innovative networked radar
system for detection of obstacles in a railway level crossing scenario.
This Monitoring System (MS) is able to detect moving or still
obstacles within the railway level crossing area automatically,
avoiding the need of human presence for surveillance. The MS is also
connected to the National Railway Information and Signaling System
to communicate in real-time the level crossing status. The
architecture is compliant with the highest Safety Integrity Level
(SIL4) of the CENELEC standard. The number of radar sensors used
is configurable at set-up time and depends on how large the level
crossing area can be. At least two sensors are expected and up four
can be used for larger areas. The whole processing chain that
elaborates the output sensor signals, as well as the communication
interface, is fully-digital, was designed in VHDL code and
implemented onto a Xilinx Virtex 6.
Abstract: The mechanisms underlying the association between
obesity and asthma may be related to a decreased immunological
tolerance induced by a defective function of regulatory T cells
(Tregs). The aim of this study is to establish the potential link
between these diseases and CD4+, CD25+ FoxP3+ Tregs as well as T
helper cells (Ths) in children. This is a prospective case control
study. Obese (n:40), asthmatic (n:40), asthmatic obese (n:40) and
healthy children (n:40), who don't have any acute or chronic diseases,
were included in this study. Obese children were evaluated according
to WHO criteria. Asthmatic patients were chosen based on GINA
criteria. Parents were asked to fill up the questionnaire. Informed
consent forms were taken. Blood samples were marked with CD4+,
CD25+ and FoxP3+ in order to determine Tregs and Ths by flow
cytometric method. Statistical analyses were performed. p≤0.05 was
chosen as meaningful threshold. Tregs exhibiting anti-inflammatory
nature were significantly lower in obese (0,16%; p≤0,001), asthmatic
(0,25%; p≤0,01) and asthmatic obese (0,29%; p≤0,05) groups than
the control group (0,38%). Ths were counted higher in asthma group
than the control (p≤0,01) and obese (p≤0,001) groups. T cell
immunity plays important roles in obesity and asthma pathogeneses.
Decreased numbers of Tregs found in obese, asthmatic and asthmatic
obese children may help to elucidate some questions in
pathophysiology of these diseases. For HOMA-IR levels, any
significant difference was not noted between control and obese
groups, but statistically higher values were found for obese
asthmatics. The values obtained in all groups were found to be below
the critical cut off points. This finding has made the statistically
significant difference observed between Tregs of obese, asthmatic,
obese asthmatic and control groups much more valuable. These
findings will be useful in diagnosis and treatment of these disorders
and future studies are needed. The production and propagation of
Tregs may be promising in alternative asthma and obesity treatments.