Abstract: Useful lifetime evaluation of chevron rubber spring
was very important in design procedure to assure the safety and
reliability. It is, therefore, necessary to establish a suitable criterion
for the replacement period of chevron rubber spring. In this study, we
performed characteristic analysis and useful lifetime prediction of
chevron rubber spring. Rubber material coefficient was obtained by
curve fittings of uniaxial tension equibiaxial tension and pure shear
test. Computer simulation was executed to predict and evaluate the
load capacity and stiffness for chevron rubber spring. In order to
useful lifetime prediction of rubber material, we carried out the
compression set with heat aging test in an oven at the temperature
ranging from 50°C to 100°C during a period 180 days. By using the
Arrhenius plot, several useful lifetime prediction equations for rubber
material was proposed.
Abstract: The nickel-manganese (Ni-Mn) alloy coating prepared
from DC electrodeposition process in sulphamate bath was studied.
The effects of process parameters, such as current density and
electrolyte composition, on the cathodic current efficiency,
microstructure, internal stress and mechanical properties were
investigated. Because of its crucial effect on the application to the
electroforming of microelectronic components, the development of
low internal stress coating with high leveling power was emphasized.
It was found that both the coating’s manganese content and the
cathodic current efficiency increased with the raise in current density.
In addition, the internal stress of the deposited coating showed
compressive nature at low current densities while changed to tensile
one at higher current densities. Moreover, the metallographic
observation, X-ray diffraction measurement, and polarization curve
measurement were conducted. It was found that the Ni-Mn coating
consisted of nano-sized columnar grains and the maximum hardness of
the coating was associated with (111) preferred orientation in the
microstructure. The grain size was refined along with the increase in
the manganese content of the coating, which accordingly, raised its
hardness and resistance to annealing softening. In summary, the
Ni-Mn coating prepared at lower current density of 1-2 A/dm2 had low
internal stress, high leveling power, and better corrosion resistance.
Abstract: This study aims to investigate the mixing behaviors of
deionized (DI) water and carboxymethyl cellulose (CMC) solutions in
C-shaped serpentine micromixers over a wide range of flow
conditions. The flow of CMC solutions exhibits shear-thinning
behaviors. Numerical simulations are performed to investigate the
effects of the mean flow speed, fluid properties and geometry
parameters on flow and mixing in the micromixers with the serpentine
channel of the same overall channel length. From the results, we can
find the following trends. When convection dominates fluid mixing,
the curvature-induced vortices enhance fluid mixing effectively. The
mixing efficiency of a micromixer consisting of semicircular C-shaped
repeating units with a smaller centerline radius is better than that of a
micromixer consisting of major segment repeating units with a larger
centerline radius. The viscosity of DI water is less than the overall
average apparent viscosity of CMC solutions, and so the effect of
curvature-induced vortices on fluid mixing in DI water is larger than
that in CMC solutions for the cases with the same mean flow speed.
Abstract: A large amount of software products offer a wide
range and number of features. This is called featuritis or creeping
featurism and tends to rise with each release of the product. Feautiris
often adds unnecessary complexity to software, leading to longer
learning curves and overall confusing the users and degrading their
experience. We take a look to a new design approach tendency that
has been coming up, the so-called “What You Get is What You
Need” concept that argues that products should be very focused,
simple and with minimalistic interfaces in order to help users conduct
their tasks in distraction-free ambiences. This isn’t as simple to
implement as it might sound and the developers need to cut down
features. Our contribution illustrates and evaluates this design method
through a novel distraction-free diagramming tool named Delineato
Pro for Mac OS X in which the user is confronted with an empty
canvas when launching the software and where tools only show up
when really needed.
Abstract: This paper presents the design process of a high
performance 3-phase 3.7 kW 2-pole line start permanent magnet
synchronous motor for pumping system. A method was proposed to
study the starting torque characteristics considering line start with
high inertia load. A d-q model including cage was built to study the
synchronization capability. Time-stepping finite element method
analysis was utilized to accurately predict the dynamic and transient
performance, efficiency, starting current, speed curve and etc.
Considering the load torque of pumps during starting stage, the rotor
bar was designed with minimum demagnetization of permanent
magnet caused by huge starting current.
Abstract: The Composite Shear Walls (CSW) with steel encased
profiles can be used as lateral-load resisting systems for buildings
that require considerable large lateral-load capacity. The aim of this
work is to propose the experimental work conducted on CSW having
L section folded plate (L shape steel made-up sections) as
longitudinal reinforcement in boundary regions. The study in this
paper present the experimental test conducted on CSW having L
section folded plate as longitudinal reinforcement in boundary
regions. The tested 1/3 geometric scaled CSW has aspect ratio of 3.2.
L-shape structural steel materials with 2L-19x57x7mm dimensions
were placed in shear wall boundary zones. The seismic behavior of
CSW test specimen was investigated by evaluating and interpreting
the hysteresis curves, envelope curves, rigidity and consumed energy
graphs of this tested element. In addition to this, the experimental
results, deformation and cracking patterns were evaluated, interpreted
and suggestions of the design recommendations were proposed.
Abstract: In recent years, fire accidents have been steadily
increased and the amount of property damage caused by the accidents
has gradually raised. Damaging building structure, fire incidents bring
about not only such property damage but also strength degradation and
member deformation. As a result, the building structure undermines its
structural ability. Examining the degradation and the deformation is
very important because reusing the building is more economical than
reconstruction. Therefore, engineers need to investigate the strength
degradation and member deformation well, and make sure that they
apply right rehabilitation methods. This study aims at evaluating
deformation characteristics of fire damaged and rehabilitated normal
strength concrete beams through both experiments and finite element
analyses. For the experiments, control beams, fire damaged beams and
rehabilitated beams are tested to examine deformation characteristics.
Ten test beam specimens with compressive strength of 21MPa are
fabricated and main test variables are selected as cover thickness of
40mm and 50mm and fire exposure time of 1 hour or 2 hours. After
heating, fire damaged beams are air-recurred for 2 months and
rehabilitated beams are repaired with polymeric cement mortar after
being removed the fire damaged concrete cover. All beam specimens
are tested under four points loading. FE analyses are executed to
investigate the effects of main parameters applied to experimental
study. Test results show that both maximum load and stiffness of the
rehabilitated beams are higher than those of the fire damaged beams.
In addition, predicted structural behaviors from the analyses also show
good rehabilitation effect and the predicted load-deflection curves are
similar to the experimental results. For the further, the proposed
analytical method can be used to predict deformation characteristics of
fire damaged and rehabilitated concrete beams without suffering from
time and cost consuming of experimental process.
Abstract: Sound processing is one the subjects that newly
attracts a lot of researchers. It is efficient and usually less expensive
than other methods. In this paper the flow generated sound is used to
estimate the flow speed of free flows. Many sound samples are
gathered. After analyzing the data, a parameter named wave power is
chosen. For all samples the wave power is calculated and averaged
for each flow speed. A curve is fitted to the averaged data and a
correlation between the wave power and flow speed is found. Test
data are used to validate the method and errors for all test data were
under 10 percent. The speed of the flow can be estimated by
calculating the wave power of the flow generated sound and using the
proposed correlation.
Abstract: This paper describes a new approach which can be
used to interpret the experimental creep deformation data obtained
from miniaturized thin plate bending specimen test to the
corresponding uniaxial data based on an inversed application of the
reference stress method. The geometry of the thin plate is fully
defined by the span of the support, l, the width, b, and the thickness,
d. Firstly, analytical solutions for the steady-state, load-line creep
deformation rate of the thin plates for a Norton’s power law under
plane stress (b→0) and plane strain (b→∞) conditions were obtained,
from which it can be seen that the load-line deformation rate of the
thin plate under plane-stress conditions is much higher than that
under the plane-strain conditions. Since analytical solution is not
available for the plates with random b-values, finite element (FE)
analyses are used to obtain the solutions. Based on the FE results
obtained for various b/l ratios and creep exponent, n, as well as the
analytical solutions under plane stress and plane strain conditions, an
approximate, numerical solutions for the deformation rate are
obtained by curve fitting. Using these solutions, a reference stress
method is utilised to establish the conversion relationships between
the applied load and the equivalent uniaxial stress and between the
creep deformations of thin plate and the equivalent uniaxial creep
strains. Finally, the accuracy of the empirical solution was assessed
by using a set of “theoretical” experimental data.
Abstract: Numerical investigations were conducted to study the
influence of flexural reinforcement ratio on the diagonal cracking
strength and ultimate shear strength of reinforced concrete (RC)
beams without stirrups. Three-dimensional nonlinear finite element
analyses (FEAs) of the beams with flexural reinforcement ratios
ranging from 0.58% to 2.20% subjected to a mid-span concentrated
load were carried out. It is observed that the load-deflection and loadstrain
curves obtained from the numerical analyses agree with those
obtained from the experiments. It is concluded that flexural
reinforcement ratio has a significant effect on the shear strength and
deflection capacity of RC beams without stirrups. The predictions of
diagonal cracking strength and ultimate shear strength of beams
obtained by using the equations defined by a number of codes and
researchers are compared with each other and with the experimental
values.
Abstract: In this work new macroporous Ni electrodes modified
with Au nanoparticles for hydrogen production have been developed.
The supporting macroporous Ni electrodes have been obtained by
means of the electrodeposition at high current densities. Then, the Au
nanoparticles were synthesized and added to the electrode surface.
The electrocatalytic behaviour of the developed electrocatalysts was
studied by means of pseudo-steady-state polarization curves,
electrochemical impedance spectroscopy (EIS) and hydrogen
discharge curves. The size of the Au synthetized nanoparticles shows
a monomodal distribution, with a very sharp band between 10 and 50
nm. The characteristic parameters d10, d50 and d90 were 14, 20 and
31 nm respectively. From Tafel polarization data has been concluded
that the Au nanoparticles improve the catalytic activity of the
developed electrodes towards the HER respect to the macroporous Ni
electrodes. EIS permits to obtain the electrochemically active area by
means of the roughness factor value. All the developed electrodes
show roughness factor values in the same order of magnitude. From
the activation energy results it can be concluded that the Au
nanoparticles improve the intrinsic catalytic activity of the
macroporous Ni electrodes.
Abstract: In the field of fashion design, 3D Mannequin is a kind
of assisting tool which could rapidly realize the design concepts.
While the concept of 3D Mannequin is applied to the computer added
fashion design, it will connect with the development and the
application of design platform and system. Thus, the situation
mentioned above revealed a truth that it is very critical to develop a
module of 3D Mannequin which would correspond with the necessity
of fashion design. This research proposes a concrete plan that
developing and constructing a system of 3D Mannequin with Kinect.
In the content, ergonomic measurements of objective human features
could be attained real-time through the implement with depth camera
of Kinect, and then the mesh morphing can be implemented through
transformed the locations of the control-points on the model by
inputting those ergonomic data to get an exclusive 3D mannequin
model. In the proposed methodology, after the scanned points from the
Kinect are revised for accuracy and smoothening, a complete human
feature would be reconstructed by the ICP algorithm with the method
of image processing. Also, the objective human feature could be
recognized to analyze and get real measurements. Furthermore, the
data of ergonomic measurements could be applied to shape morphing
for the division of 3D Mannequin reconstructed by feature curves. Due
to a standardized and customer-oriented 3D Mannequin would be
generated by the implement of subdivision, the research could be
applied to the fashion design or the presentation and display of 3D
virtual clothes. In order to examine the practicality of research
structure, a system of 3D Mannequin would be constructed with JAVA
program in this study. Through the revision of experiments the
practicability-contained research result would come out.
Abstract: The flow duration curve (FDC) is an informative
method that represents the flow regime’s properties for a river basin.
Therefore, the FDC is widely used for water resource projects such as
hydropower, water supply, irrigation and water quality management.
The primary purpose of this study is to obtain synthetic daily flow
duration curves for Çoruh Basin, Turkey. For this aim, we firstly
developed univariate auto-regressive moving average (ARMA)
models for daily flows of 9 stations located in Çoruh basin and then
these models were used to generate 100 synthetic flow series each
having same size as historical series. Secondly, flow duration curves
of each synthetic series were drawn and the flow values exceeded 10,
50 and 95% of the time and 95% confidence limit of these flows were
calculated. As a result, flood, mean and low flows potential of Çoruh
basin will comprehensively be represented.
Abstract: In this study, the experiments were carried out to
determine the best coolant for the quenching process among waterbased
silica, alumina, titania and copper oxide nanofluids (0.1 vol%).
A sphere made up off brass material was used in the experiments.
When the spherical test specimen was heated at high temperatures, it
was suddenly immersed into the nanofluids. All experiments were
carried out at saturated conditions and under atmospheric pressure.
After the experiments, the cooling curves were obtained by using the
temperature-time data of the specimen. The experimental results
showed that the cooling performance of test specimen depended on
the type of nanofluids. The silica nanoparticles enhanced the
performance of boiling heat transfer and it is the best coolant for the
quenching among other nanoparticles.
Abstract: Biodiesel as an alternative diesel fuel is steadily gaining more attention and significance. However, there are some drawbacks while using biodiesel regarding its properties that requires it to be blended with petrol based diesel and/or additives to improve the fuel characteristics. This study analyses thermal cracking as an alternative technology to improve biodiesel characteristics in which, FAME based biodiesel produced by transesterification of castor oil is fed into a continuous thermal cracking reactor at temperatures range of 450-500°C and flowrate range of 20-40 g/hr. Experiments designed by response surface methodology and subsequent statistical studies show that temperature and feed flowrate significantly affect the products yield. Response surfaces were used to study the impact of temperature and flowrate on the product properties. After each experiment, the produced crude bio-oil was distilled and diesel cut was separated. As shorter chain molecules are produced through thermal cracking, the distillation curve of the diesel cut fitted more with petrol based diesel curve in comparison to the biodiesel. Moreover, the produced diesel cut properties adequately pose within property ranges defined by the related standard of petrol based diesel. Cold flow properties, high heating value as the main drawbacks of the biodiesel are improved by this technology. Thermal cracking decreases kinematic viscosity, Flash point and cetane number.
Abstract: Aluminium matrix composites with alumina
reinforcements give superior mechanical & physical properties. Their
applications in several fields like automobile, aerospace, defense,
sports, electronics, bio-medical and other industrial purposes are
becoming essential for the last several decades. In the present work,
fabrication of hybrid composite was done by Stir casting technique
using Al 6061 as a matrix with alumina and silicon carbide (SiC) as
reinforcement materials. The weight percentage of alumina is varied
from 2 to 4% and the silicon carbide weight percentage is maintained
constant at 2%. Hardness and wear tests are performed in the as cast
and heat treated conditions. Age hardening treatment was performed
on the specimen with solutionizing at 550°C, aging at two
temperatures (150 and 200°C) for different time durations. Hardness
distribution curves are drawn and peak hardness values are recorded.
Hardness increase was very sensitive with respect to the decrease in
aging temperature. There was an improvement in wear resistance of
the peak aged material when aged at lower temperature. Also
increase in weight percent of alumina, increases wear resistance at
lower temperature but opposite behavior was seen when aged at
higher temperature.
Abstract: The nanoindentation behaviour and phase
transformation of annealed single-crystal silicon wafers are examined.
The silicon specimens are annealed at temperatures of 250, 350 and
450ºC, respectively, for 15 minutes and are then indented to maximum
loads of 30, 50 and 70 mN. The phase changes induced in the indented
specimens are observed using transmission electron microscopy
(TEM) and micro-Raman scattering spectroscopy (RSS). For all
annealing temperatures, an elbow feature is observed in the unloading
curve following indentation to a maximum load of 30 mN. Under
higher loads of 50 mN and 70 mN, respectively, the elbow feature is
replaced by a pop-out event. The elbow feature reveals a complete
amorphous phase transformation within the indented zone, whereas
the pop-out event indicates the formation of Si XII and Si III phases.
The experimental results show that the formation of these crystalline
silicon phases increases with an increasing annealing temperature and
indentation load. The hardness and Young’s modulus both decrease as
the annealing temperature and indentation load are increased.
Abstract: Experimental studies to investigate the depth of the
scour conducted at a side-weir intersection located at the 1800 curved
flume which located Hydraulic Laboratory of Yıldız Technical
University, Istanbul, Turkey. Side weirs were located at the middle of
the straight part of the main channel. Three different lengths (25, 40
and 50 cm) and three different weir crest height (7, 10 and 12 cm) of
the side weir placed on the side weir station. There is no scour when
the material is only kaolin. Therefore, the cohesive bed was prepared
by properly mixing clay material (kaolin) with 31% sand in all
experiments. Following 24h consolidation time, in order to observe
the effect of flow intensity on the scour depth, experiments were
carried out for five different upstream Froude numbers in the range of
0.33-0.81.
As a result of this study the relation between scour depth and
upstream flow intensity as a function of time have been established.
The longitudinal velocities decreased along the side weir; towards the
downstream due to overflow over the side-weirs. At the beginning,
the scour depth increases rapidly with time and then asymptotically
approached constant values in all experiments for all side weir
dimensions as in non-cohesive sediment. Thus, the scour depth
reached equilibrium conditions. Time to equilibrium depends on the
approach flow intensity and the dimensions of side weirs. For
different heights of the weir crest, dimensionless scour depths
increased with increasing upstream Froude number. Equilibrium
scour depths which formed 7 cm side-weir crest height were obtained
higher than that of the 12 cm side-weir crest height. This means when
side-weir crest height increased equilibrium scour depths decreased.
Although the upstream side of the scour hole is almost vertical, the
downstream side of the hole is inclined.
Abstract: This paper presents a rank correlation curve. The
traditional correlation coefficient is valid for both continuous
variables and for integer variables using rank statistics. Since
the correlation coefficient has already been established in rank
statistics by Spearman, such a calculation can be extended to
the correlation curve.
This paper presents two survey questions. The survey
collected non-continuous variables. We will show weak to
moderate correlation. Obviously, one question has a negative
effect on the other. A review of the qualitative literature
can answer which question and why. The rank correlation
curve shows which collection of responses has a positive
slope and which collection of responses has a negative slope.
Such information is unavailable from the flat, ”first-glance”
correlation statistics.
Abstract: Waste load allocation (WLA) policies may use multiobjective
optimization methods to find the most appropriate and
sustainable solutions. These usually intend to simultaneously
minimize two criteria, total abatement costs (TC) and environmental
violations (EV). If other criteria, such as inequity, need for
minimization as well, it requires introducing more binary
optimizations through different scenarios. In order to reduce the
calculation steps, this study presents value index as an innovative
decision making approach. Since the value index contains both the
environmental violation and treatment costs, it can be maximized
simultaneously with the equity index. It implies that the definition of
different scenarios for environmental violations is no longer required.
Furthermore, the solution is not necessarily the point with minimized
total costs or environmental violations. This idea is testified for Haraz
River, in north of Iran. Here, the dissolved oxygen (DO) level of river
is simulated by Streeter-Phelps equation in MATLAB software. The
WLA is determined for fish farms using multi-objective particle
swarm optimization (MOPSO) in two scenarios. At first, the trade-off
curves of TC-EV and TC-Inequity are plotted separately as the
conventional approach. In the second, the Value-Equity curve is
derived. The comparative results show that the solutions are in a
similar range of inequity with lower total costs. This is due to the
freedom of environmental violation attained in value index. As a
result, the conventional approach can well be replaced by the value
index particularly for problems optimizing these objectives. This
reduces the process to achieve the best solutions and may find better
classification for scenario definition. It is also concluded that decision
makers are better to focus on value index and weighting its contents
to find the most sustainable alternatives based on their requirements.