Abstract: The heat and mass transfer was investigated during the falling rate period of spray drying of a slurry droplet. The effect of the porosity of crust layer formed from primary particles during liquid evaporation was studied numerically using the developed mathematical model which takes into account the heat and mass transfer in the core and crust regions, the movement of the evaporation interface, and the external heat and mass transfer between the drying air and the droplet surface. It was confirmed that the heat transfer through the crust layer was more intense in the case of the dense droplet than the loose one due to the enhanced thermal conduction resulting in the higher average droplet temperature. The mass transfer was facilitated in the crust layer of loose droplet owing to the large pore space available for diffusion of water vapor from the evaporation interface to the outer droplet surface. The longer drying time is required for the droplet of high porosity to reach the final moisture content than that for the dense one due to the larger amount of water to be evaporated during the falling rate.
Abstract: Simultaneous measurements of the curves for wear versus distance, wear rate versus distance, and coefficient of friction versus distance were performed in situ to distinguish the transition from severe running-in wear to mild wear. The effects of the initial surface roughness on the severe running-in wear volume were investigated. Disk-on-plate friction and wear tests were carried out with SUS304 austenitic stainless steel in contact with itself under repeated dry sliding conditions at room temperature. The wear volume was dependent on the initial surface roughness. The wear volume when the initial surfaces on the plate and disk had dissimilar roughness was lower than that when these surfaces had similar roughness. For the dissimilar roughness, the wear volume decreased with decreasing initial surface roughness and reached a minimum; it stayed nearly constant as the roughness was less than the mean size of the oxide particles.
Abstract: This experiment aims to demonstrate the efficacy of ceramic powder derived from various sources to inactivate avian influenza virus and its possibility to use in the environment. The ceramics used in the present experiment were derived from chicken feces (CF), scallop shell (SS), polyvinyl chloride (PVC) and soybean (SB). All ceramics were mixed with low pathogenic AIV (LPAIV) H7N1, and then kept at room temperature. The recovered virus was titrated onto Madin-Darby canine kidney (MDCK) cells. All ceramics were assessed the inactivation stability in the environment by keeping under sunlight and under wet-dry condition until reached 7 week or 7 resuspension times respectively. The results indicate that all ceramics have excellent efficacy to inactivate LPAIV. This efficacy can be maintained under the simulated condition. The ceramics are expected to be the good materials for application in the biosecurity system at farms.
Abstract: The current-voltage characteristics of a PtSi/p-Si
Schottky barrier diode was measured at the temperature of 85 K and
from the forward bias region of the I-V curve, the electrical
parameters of the diode were measured by three methods. The results
obtained from the two methods which considered the series resistance
were in close agreement with each other and from them barrier height
(), ideality factor (n) and series resistance () were found to be
0.2045 eV, 2.877 and 14.556 K respectively. By measuring the I-V
characteristics in the temperature range of 85-136 K the electrical
parameters were observed to have strong dependency on temperature.
The increase of barrier height and decrease of ideality factor with
increasing temperature is attributed to the existence of barrier height
inhomogeneities in the silicide-semiconductor structure.
Abstract: In this work, the influence of temperature on the
different parameters of solar cells based on organic semiconductors
are studied. The short circuit current Isc increases so monotonous
with temperature and then saturates to a maximum value before
decreasing at high temperatures. The open circuit voltage Vco
decreases linearly with temperature. The fill factor FF and efficiency,
which are directly related with Isc and Vco follow the variations of
the letters. The phenomena are explained by the behaviour of the
mobility which is a temperature activated process.
Abstract: Spatial outliers in remotely sensed imageries represent
observed quantities showing unusual values compared to their
neighbor pixel values. There have been various methods to detect the
spatial outliers based on spatial autocorrelations in statistics and data
mining. These methods may be applied in detecting forest fire pixels
in the MODIS imageries from NASA-s AQUA satellite. This is
because the forest fire detection can be referred to as finding spatial
outliers using spatial variation of brightness temperature. This point is
what distinguishes our approach from the traditional fire detection
methods. In this paper, we propose a graph-based forest fire detection
algorithm which is based on spatial outlier detection methods, and test
the proposed algorithm to evaluate its applicability. For this the
ordinary scatter plot and Moran-s scatter plot were used. In order to
evaluate the proposed algorithm, the results were compared with the
MODIS fire product provided by the NASA MODIS Science Team,
which showed the possibility of the proposed algorithm in detecting
the fire pixels.
Abstract: A vertical SOI-based MOSFET with trench body
structure operated as 1T DRAM cell at various temperatures has been
studied and investigated. Different operation temperatures are
assigned for the device for its performance comparison, thus the
thermal stability is carefully evaluated for the future memory device
applications. Based on the simulation, the vertical SOI-based
MOSFET with trench body structure demonstrates the electrical
characteristics properly and possess conspicuous kink effect at
various operation temperatures. Transient characteristics were also
performed to prove that its programming window values and
retention time behaviors are acceptable when the new 1T DRAM cell
is operated at high operation temperature.
Abstract: This study aims to discuss the effect of illumination and the color temperature of the lighting source under the office lighting environment on human psychological and physiological responses. In this study, 21 healthy participants were selected, and the Ryodoraku measurement system was utilized to measure their skin resistance change.The findings indicated that the effect of the color temperature of the lighting source on human physiological responses is significant within 90 min after turning the lights on; while after 90 min the effect of illumination on human physiological responses is higher than that of the color temperature. Moreover, the cardiovascular, digestive and endocrine systems are prone to be affected by the indoor lighting environment. During the long-term exposure to high intensity of illumination and high color temperature (2000Lux -6500K), the effect on the psychological responses turned moderate after the human visual system adopted to the lighting environment. However, the effect of the Ryodoraku value on human physiological responses was more significant with the increase of perceptive time. The effect of long time exposure to a lighting environment on the physiological responses is greater than its effect on the psychological responses. This conclusion is different from the traditional public viewpoint that the effect on the psychological responses is greater.
Abstract: In this study we present the effect of elevated
temperatures from 300K to 400K on the electrical properties of
copper Phthalocyanine (CuPc) based organic field effect transistors
(OFET). Thin films of organic semiconductor CuPc (40nm) and
semitransparent Al (20nm) were deposited in sequence, by vacuum
evaporation on a glass substrate with previously deposited Ag source
and drain electrodes with a gap of 40 μm. Under resistive mode of
operation, where gate was suspended it was observed that drain
current of this organic field effect transistor (OFET) show an
increase with temperature. While in grounded gate condition metal
(aluminum) – semiconductor (Copper Phthalocyanine) Schottky
junction dominated the output characteristics and device showed
switching effect from low to high conduction states like Zener diode
at higher bias voltages. This threshold voltage for switching effect
has been found to be inversely proportional to temperature and shows
an abrupt decrease after knee temperature of 360K. Change in
dynamic resistance (Rd = dV/dI) with respect to temperature was
observed to be -1%/K.
Abstract: The prediction of meteorological parameters at a
meteorological station is an interesting and open problem. A firstorder
linear dynamic model GM(1,1) is the main component of the
grey system theory. The grey model requires only a few previous data
points in order to make a real-time forecast. In this paper, we
consider the daily average ambient temperature as a time series and
the grey model GM(1,1) applied to local prediction (short-term
prediction) of the temperature. In the same case study we use a fuzzy
predictive model for global prediction. We conclude the paper with a
comparison between local and global prediction schemes.
Abstract: In the present work the internal sulfate attack on
pastes made from pure clinker phases was studied. Two binders were
produced: (a) a binder with 2% C3A and 18% C4AF content; (b) a
binder with 10% C3A and C4AF content each. Gypsum was used as
the sulfate bearing compound, while calcium carbonate added to
differentiate the binders produced. The phases formed were identified
by XRD analysis. The results showed that ettringite was the
deterioration phase detected in the case of the low C3A content
binder. Carbonation occurred in the specimen without calcium
carbonate addition, while portlandite was observed in the one
containing calcium carbonate. In the case of the high C3A content
binder, traces of thaumasite were detected when calcium carbonate
was not incorporated in the binder. A solid solution of thaumasite and
ettringite was found when calcium carbonate was added. The amount
of C3A had not fully reacted with sulfates, since its corresponding
peaks were detected.
Abstract: Hybrid photovoltaic thermal (PV/T) solar system comprises a solar collector which is disposed on photovoltaic solar cells. The disadvantage of a conventional photovoltaic cell is that its performance decreases as the temperature increases. Indeed, part of the solar radiation is converted into electricity and is dissipated as heat, increasing the temperature of the photovoltaic cell with respect to the ambient temperature. The objective of this work is to study experimentally and implement a hybrid prototype to evaluate electrical and thermal performance. In this paper, an experimental study of two new configurations of hybrid collectors is exposed. The results are given and interpreted. The two configurations of absorber studied are a new combination with tubes and galvanized tank, the other is a tubes and sheet.
Abstract: The occurrence and removal of trace organic
contaminants in the aquatic environment has become a focus of
environmental concern. For the selective removal of carbamazepine
from loaded waters molecularly imprinted polymers (MIPs) were
synthesized with carbamazepine as template. Parameters varied were
the type of monomer, crosslinker, and porogen, the ratio of starting
materials, and the synthesis temperature. Best results were obtained
with a template to crosslinker ratio of 1:20, toluene as porogen, and
methacrylic acid (MAA) as monomer. MIPs were then capable to
recover carbamazepine by 93% from a 10-5 M landfill leachate
solution containing also caffeine and salicylic acid. By comparison,
carbamazepine recoveries of 75% were achieved using a nonimprinted
polymer (NIP) synthesized under the same conditions, but
without template. In landfill leachate containing solutions
carbamazepine was adsorbed by 93-96% compared with an uptake of
73% by activated carbon. The best solvent for desorption was
acetonitrile, with which the amount of solvent necessary and dilution
with water was tested. Selected MIPs were tested for their reusability
and showed good results for at least five cycles. Adsorption
isotherms were prepared with carbamazepine solutions in the
concentration range of 0.01 M to 5*10-6 M. The heterogeneity index
showed a more homogenous binding site distribution.
Abstract: This paper reported an experimental research of
steady-state heat transfer behaviour of a gas flowing through a fixed
bed under the different operating conditions. Studies had been carried
out in a fixed-bed packed methanol synthesis catalyst percolated by air
at appropriate flow rate. Both radial and axial direction temperature
distribution had been investigated under the different operating
conditions. The effects of operating conditions including the reactor
inlet air temperature, the heating pipe temperature and the air flow rate
on temperature distribution was investigated and the experimental
results showed that a higher inlet air temperature was conducive to
uniform temperature distribution in the fixed bed. A large temperature
drop existed at the radial direction, and the temperature drop increased
with the heating pipe temperature increasing under the experimental
conditions; the temperature profile of the vicinity of the heating pipe
was strongly affected by the heating pipe temperature. A higher air
flow rate can improve the heat transfer in the fixed bed. Based on the
thermal distribution, heat transfer models of the fixed bed could be
established, and the characteristics of the temperature distribution in
the fixed bed could be finely described, that had an important practical
significance.
Abstract: Freeze concentration freezes or crystallises the water
molecules out as ice crystals and leaves behind a highly concentrated
solution. In conventional suspension freeze concentration where ice
crystals formed as a suspension in the mother liquor, separation of
ice is difficult. The size of the ice crystals is still very limited which
will require usage of scraped surface heat exchangers, which is very
expensive and accounted for approximately 30% of the capital cost.
This research is conducted using a newer method of freeze
concentration, which is progressive freeze concentration. Ice crystals
were formed as a layer on the designed heat exchanger surface. In
this particular research, a helical structured copper crystallisation
chamber was designed and fabricated. The effect of two operating
conditions on the performance of the newly designed crystallisation
chamber was investigated, which are circulation flowrate and coolant
temperature. The performance of the design was evaluated by the
effective partition constant, K, calculated from the volume and
concentration of the solid and liquid phase. The system was also
monitored by a data acquisition tool in order to see the temperature
profile throughout the process. On completing the experimental
work, it was found that higher flowrate resulted in a lower K, which
translated into high efficiency. The efficiency is the highest at 1000
ml/min. It was also found that the process gives the highest
efficiency at a coolant temperature of -6 °C.
Abstract: Use of a sliding joint is an effective method to
decrease the stress in foundation structure where there is a horizontal
deformation of subsoil (areas afflicted with underground mining) or
horizontal deformation of a foundation structure (pre-stressed
foundations, creep, shrinkage, temperature deformation). A
convenient material for a sliding joint is a bitumen asphalt belt.
Experiments for different types of bitumen belts were undertaken at
the Faculty of Civil Engineering - VSB Technical University of
Ostrava in 2008. This year an extension of the 2008 experiments is in
progress and the shear resistance of a slide joint is being tested as a
function of temperature in a temperature controlled room. In this
paper experimental results of temperature dependant shear resistance
are presented. The result of the experiments should be the sliding
joint shear resistance as a function of deformation velocity and
temperature. This relationship is used for numerical analysis of
stress/strain relation between foundation structure and subsoil. Using
a rheological slide joint could lead to a decrease of the reinforcement
amount, and contribute to higher reliability of foundation structure
and thus enable design of more durable and sustainable building
structures.
Abstract: Combined conduction-free convection heat transfer in
vertical eccentric annuli is numerically investigated using a finitedifference
technique. Numerical results, representing the heat transfer
parameters such as annulus walls temperature, heat flux, and heat
absorbed in the developing region of the annulus, are presented for a
Newtonian fluid of Prandtl number 0.7, fluid-annulus radius ratio 0.5,
solid-fluid thermal conductivity ratio 10, inner and outer wall
dimensionless thicknesses 0.1 and 0.2, respectively, and
dimensionless eccentricities 0.1, 0.3, 0.5, and 0.7. The annulus walls
are subjected to thermal boundary conditions, which are obtained by
heating one wall isothermally whereas keeping the other wall at inlet
fluid temperature. In the present paper, the annulus heights required
to achieve thermal full development for prescribed eccentricities are
obtained. Furthermore, the variation in the height of thermal full
development as function of the geometrical parameter, i.e.,
eccentricity is also investigated.
Abstract: Starch/chitosan blend have been prepared via the
solution casting technique. Ionic conductivity for the system was
conducted over a wide range of frequency between 50 Hz-1 MHz and
at temperatures between 303 K and 373 K. Sample with 35 wt% of
NH4NO3 shows the highest conductivity of 3.89 ± 0.79 x 10-5 Scm-1
at room temperature. Conductivity-temperature relationship suggests
that samples are Arrhenian. Power law exponent was obtained
through dielectric loss variation and the trend suggests that the
conduction mechanism of the ions can be represented by the
correlated barrier hopping (CBH) model.
Abstract: Production of hard-to-cut materials with uncoated carbide cutting tools in turning, not only cause tool life reduction but also, impairs the product surface roughness. In this paper, influence of hot machining method were studied and presented in two cases. Case1-Workpiece surface roughness quality with constant cutting parameter and 300 ºC initial workpiece surface temperature. Case 2- Tool temperature variation when cutting with two speeds 78.5 (m/min) and 51 (m/min). The workpiece material and tool used in this study were AISI 1060 steel (45HRC) and uncoated carbide TNNM 120408-SP10(SANDVIK Coromant) respectively. A gas flam heating source was used to preheating of the workpiece surface up to 300 ºC, causing reduction of yield stress about 15%. Results obtained experimentally, show that the method used can considerably improved surface quality of the workpiece.
Abstract: Homogeneous composites of alumina and zirconia
with a small amount of MgO (99%) were obtained for ZTA ceramic containing 0.05 wt% MgO in
1500 °C.