Abstract: Mangosteen (Garcinia mangostana) pericarp is
considered as agricultural waste and not fully utilized in food
products. It is widely reported that mangosteen pericarp contains high
antioxidant properties. The objective of this study is to develop novel
yellow alkaline noodle (YAN) substituted with different levels of
mangosteen pericarp powder (MPP). YAN formulation was
substituted with different levels of MPP (0%, 5%, 10% and 15%).
The effect on nutritional and antioxidant properties was evaluated.
Higher substitution levels of MPP resulted in significant increase
(p
Abstract: Fly ash (FA) thanks to the significant presence of SiO2
and Al2O3 as the main components is a potential raw material for
geopolymers production. Mechanical activation is a method for
improving FA reactivity and also the porosity of final mixture; those
parameters can be analysed through sorption properties. They have
direct impact on the durability of fly ash based geopolymer mortars.
In the paper, effect of FA fineness on sorption properties of
geopolymers based on sodium silicate, as well as relationship
between fly ash fineness and apparent density, compressive and
flexural strength of geopolymers are presented. The best results in the
evaluated area reached the sample H1, which contents the highest
portion of particle under 20μm (100% of GFA). The interdependence
of individual tested properties was confirmed for geopolymer
mixtures corresponding to those in the cement based mixtures: higher
is portion of fine particles < 20μm, higher is strength, density and
lower are sorption properties. The compressive strength as well as
sorption parameters of the geopolymer can be reasonably controlled
by grinding process and also ensured by the higher share of fine
particle (to 20μm) in total mass of the material.
Abstract: We report the microstructural and magnetic properties
of Ni50Mn39Sn11 and Ni50Mn36Sn14 ribbon Heusler alloys.
Experimental results were obtained by differential scanning
calorymetry, X-ray diffraction and vibrating sample magnetometry
techniques. The Ni-Mn-Sn system undergoes a martensitic structural
transformation in a wide temperature range. For example, for
Ni50Mn39Sn11 the start and finish temperatures of the martensitic and
austenite phase transformation for ribbon alloy were Ms=336K,
Mf=328K, As=335K and Af=343K whereas no structural
transformation is observed for Ni50Mn36Sn14 alloys. Magnetic
measurements show the typical ferromagnetic behavior with Curie
temperature 207 K at low applied field of 50 Oe. The complex
behavior exhibited by these Heusler alloys should be ascribed to the
strong coupling between magnetism and structure, being their
magnetic behavior determined by the distance between Mn atoms.
Abstract: The main objective of incorporating natural fibers such as Henequen microfibers (NF) into the High Density Polyethylene (HDPE) polymer matrix is to reduce the cost and to enhance the mechanical as well as other properties. The Henequen microfibers were chopped manually to 5-7mm in length and added into the polymer matrix at the optimized concentration of 8 wt %. In order to facilitate the link between Henequen microfibers (NF) and HDPE matrix, coupling agent such as Glycidoxy (Epoxy) Functional Methoxy Silane (GPTS) at various concentrations from 0.1%, 0.3%, 0.5%, 0.7%, 0.9% and 1% by weight to the total fibers were added. The tensile strength of the composite increased marginally while % elongation at break of the composites decreased with increase in silane loading by wt %. Tensile modulus and stiffness observed increased at 0.9 wt % GPTS loading. Flexural as well as impact strength of the composite decreased with increase in GPTS loading by weight %. Dielectric strength of the composite also found increased marginally up to 0.5wt % silane loading and thereafter remained constant.
Abstract: The study discussed in this paper was conducted in an
attempt to investigate effects of different drying methods (line dry
and tumble dry) on viscose single jersey fabrics knitted with ring
yarn.
Abstract: In this research the effect of moisture at three levels
(47, 57, and 67 w.b.%) on the physical properties of the Pofaki pea
variety including, dimensions, geometric mean diameter, volume,
sphericity index and the surface area was determined. The influence
of different moisture levels (47, 57 and 67 w.b.%), in two loading
orientation (longitudinal and transverse) and three loading speed (4,6
and 8 mm min-1) on the mechanical properties of pea such as
maximum deformation, rupture force, rupture energy, toughness and
the power to break the pea was investigated. It was observed in the
physical properties that moisture changes were affective at 1% on,
dimensions, geometric mean diameter, volume, sphericity index and
the surface area. It was observed in the mechanical properties that
moisture changes were effective at 1% on, maximum deformation,
rupture force, rupture energy, toughness and the power to break.
Loading speed was effective on maximum deformation, rupture
force, rupture energy at 1% and it was effective on toughness at 5%.
Loading orientation was effective on maximum deformation, rupture
force, rupture energy, toughness at 1% and it was effective on power
at 5%. The mutual effect of speed and orientation were effective on
rupture energy at 1% and were effective on toughness at 5%
probability. The mutual effect of moisture and speed were effective
on rupture force and rupture energy at 1% and were effective on
toughness 5% probability. The mutual effect of orientation and
moisture on rupture energy and toughness were effective at 1%.
Abstract: This study investigates the suitability of using plastic,
such as polyethylene terephthalate (PET), as a partial replacement of
natural coarse and fine aggregates (for example, brick chips and
natural sand) to produce lightweight concrete for load bearing
structural members. The plastic coarse aggregate (PCA) and plastic
fine aggregate (PFA) were produced from melted polyethylene
terephthalate (PET) bottles. Tests were conducted using three
different water–cement (w/c) ratios, such as 0.42, 0.48, and 0.57,
where PCA and PFA were used as 50% replacement of coarse and
fine aggregate respectively. Fresh and hardened properties of
concrete have been compared for natural aggregate concrete (NAC),
PCA concrete (PCC) and PFA concrete (PFC). The compressive
strength of concrete at 28 days varied with the water–cement ratio for
both the PCC and PFC. Between PCC and PFC, PFA concrete
showed the highest compressive strength (23.7 MPa) at 0.42 w/c ratio
and also the lowest compressive strength (13.7 MPa) at 0.57 w/c
ratio. Significant reduction in concrete density was mostly observed
for PCC samples, ranging between 1977–1924 kg/m³. With the
increase in water–cement ratio PCC achieved higher workability
compare to both NAC and PFC. It was found that both the PCA and
PFA contained concrete achieved the required compressive strength
to be used for structural purpose as partial replacement of the natural
aggregate; but to obtain the desired lower density as lightweight
concrete the PCA is most suited.
Abstract: The material selection in the design of the sandwich
structures is very crucial aspect because of the positive or negative
influences of the base materials to the mechanical properties of the
entire panel. In the literature, it was presented that the selection of the
skin and core materials plays very important role on the behavior of
the sandwich. Beside this, the use of the correct adhesive can make
the whole structure to show better mechanical results and behavior.
In the present work, the static three-point bending tests were
performed on the sandwiches having an aluminum alloy foam core,
the skins made of three different types of fabrics and two different
commercial adhesives (flexible polyurethane and toughened epoxy
based) at different values of support span distances by aiming the
analyses of their flexural performance in terms of absorbed energy,
peak force values and collapse mechanisms. The main results of the
flexural loading are: force-displacement curves obtained after the
bending tests, peak force and absorbed energy values, collapse
mechanisms and adhesion quality. The experimental results presented
that the sandwiches with epoxy based toughened adhesive and the
skins made of S-Glass Woven fabrics indicated the best adhesion
quality and mechanical properties. The sandwiches with toughened
adhesive exhibited higher peak force and energy absorption values
compared to the sandwiches with flexible adhesive. The use of these
sandwich structures can lead to a weight reduction of the transport
vehicles, providing an adequate structural strength under operating
conditions.
Abstract: It is well known that in recent years magnetic
materials have received increased attention due to their properties.
For this reason a significant number of patents that were published
during the last decade are oriented towards synthesis and study of
such materials. The aim of this work is to create and study ferrite
nanocrystalline materials with spinel structure, using sol-gel
technology with participation of auto-combustion. This method is
perspective in that it is a cheap and low-temperature technique that
allows for the fine control on the product’s chemical composition.
Abstract: Problems insulation of building structures is often
closely connected with the problem of moisture remediation. In the
case of historic buildings or if only part of the redevelopment of
envelope of structures, it is not possible to apply the classical external
thermal insulation composite systems. This application is mostly
effective thermal insulation plasters with high porosity and controlled
capillary properties which assures improvement of thermal properties
construction, its diffusion openness towards the external environment
and suitable treatment capillary properties of preventing the
penetration of liquid moisture and salts thereof toward the outer
surface of the structure.
With respect to the current trend of reducing the energy
consumption of building structures and reduce the production of CO2
is necessary to develop capillary-active materials characterized by
their low density, low thermal conductivity while maintaining good
mechanical properties. The aim of researchers at the Faculty of Civil
Engineering, Brno University of Technology is the development and
study of hygrothermal behaviour of optimal materials for thermal
insulation and rehabilitation of building structures with the possible
use of alternative, less energy demanding binders in comparison with
conventional, frequently used binder, which represents cement.
The paper describes the evaluation of research activities aimed at
the development of thermal insulation and repair materials using
lightweight aggregate and alternative binders such as metakaolin and
finely ground fly ash.
Abstract: Rice husk and kenaf filled with calcium carbonate
(CaCO3) and high density polyethylene (HDPE) composite were
prepared separately using twin-screw extruder at 50rpm. Different
filler loading up to 30 parts of rice husk particulate and kenaf fiber
were mixed with the fixed 30% amount of CaCO3 mineral filler to
produce rice husk/CaCO3/HDPE and kenaf/CaCO3/HDPE hybrid
composites. In this study, the effects of natural fiber for both rice
husk and kenaf in CaCO3/HDPE composite on physical, mechanical
and morphology properties were investigated. Field Emission
Scanning Microscope (FeSEM) was used to investigate the impact
fracture surfaces of the hybrid composite. The property analyses
showed that water absorption increased with the presence of kenaf
and rice husk fillers. Natural fibers in composite significantly
influence water absorption properties due to natural characters of
fibers which contain cellulose, hemicellulose and lignin structures.
The result showed that 10% of additional natural fibers into hybrid
composite had caused decreased flexural strength, however additional
of high natural fiber (>10%) filler loading has proved to increase its
flexural strength.
Abstract: Using the first-principles full-potential linearized
augmented plane wave plus local orbital (FP-LAPW+lo) method
based on density functional theory (DFT), we have investigated the
electronic structure and magnetism of full Heusler alloys Co2ZrGe
and Co2NbB. These compounds are predicted to be half-metallic
ferromagnets (HMFs) with a total magnetic moment of 2.000 B per
formula unit, well consistent with the Slater-Pauling rule.
Calculations show that both the alloys have an indirect band gaps, in
the minority-spin channel of density of states (DOS), with values of
0.58 eV and 0.47 eV for Co2ZrGe and Co2NbB, respectively.
Analysis of the DOS and magnetic moments indicates that their
magnetism is mainly related to the d-d hybridization between the Co
and Zr (or Nb) atoms. The half-metallicity is found to be relatively
robust against volume changes. In addition, an atom inside molecule
AIM formalism and an electron localization function ELF were also
adopted to study the bonding properties of these compounds, building
a bridge between their electronic and bonding behavior.
As they have a good crystallographic compatibility with the lattice of
semiconductors used industrially and negative calculated cohesive
energies with considerable absolute values these two alloys could be
promising magnetic materials in the spintronic field.
Abstract: Generating random numbers are mainly used to create
secret keys or random sequences. It can be carried out by various
techniques. In this paper we present a very simple and efficient
pseudo random number generator (PRNG) based on chaotic maps
and S-Box tables. This technique adopted two main operations one to
generate chaotic values using two logistic maps and the second to
transform them into binary words using random S-Box tables.
The simulation analysis indicates that our PRNG possessing
excellent statistical and cryptographic properties.
Abstract: This paper shortly describes various types of biomass
and a growing number of facilities utilizing the biomass in the Czech
Republic. The considerable part of this paper deals with energy
parameters of the most frequently used types of biomass and results
of their gasification testing. Sixteen most used "Czech" woody plants
and grasses were selected; raw, element and biochemical analyses
were performed and basic calorimetric values, ash composition, and
ash characteristic temperatures were identified. Later, each biofuel
was tested in a fluidized bed gasifier. The essential part of this paper
provides results of the gasification of selected biomass types.
Operating conditions are described in detail with a focus on
individual fuels properties. Gas composition and impurities content
are also identified. In terms of operating conditions and gas quality,
the essential difference occurred mainly between woody plants and
grasses. The woody plants were evaluated as more suitable fuels for
fluidized bed gasifiers. Testing results significantly help with a
decision-making process regarding suitability of energy plants for
growing and with a selection of optimal biomass-treatment
technology.
Abstract: Properties of Portland cement mixtures with various
fractions of metakaolin were studied. 10% of Portland cement CEM I
42.5 R was replaced by different fractions of high reactivity
metakaolin with defined chemical and mineralogical properties.
Various fractions of metakaolin were prepared by jet mill classifying
system. There is a clear trend between fineness of metakaolin and
hydration heat development. Due to metakaolin presence in mixtures
the compressive strength development of mortars is rather slower for
coarser fractions but 28-day flexural strengths are improved for all
fractions of metakaoline used in mixtures compared to reference
sample of pure Portland cement. Yield point, plastic viscosity and
adhesion of fresh pastes are considerably influenced by fineness of
metakaolin used in cement pastes.
Abstract: An experimental study was performed to investigate
the behavior and strength of proposed technique to connect
reinforced concrete (RC) beam to steel or composite columns. This
approach can practically be used in several types of building
construction. In this technique, the main beam of the frame consists
of a transfer part (part of beam; Tr.P) and a common reinforcement
concrete beam. The transfer part of the beam is connected to the
column, whereas the rest of the beam is connected to the transfer part
from each side. Four full-scale beam-column connections were tested
under static loading. The test parameters were the length of the
transfer part and the column properties. The test results show that
using of the transfer part technique leads to modify the deformation
capabilities for the RC beam and hence it increases its resistance
against failure. Increase in length of the transfer part did not
necessarily indicate an enhanced behavior. The test results contribute
to the characterization of the connection behavior between RC beam -
steel column and can be used to calibrate numerical models for the
simulation of this type of connection.
Abstract: To determine the potential of a low cost Irish
engineered timber product to replace high cost solid timber for use in
bending active structures such as gridshells a single Irish engineered
timber product in the form of orientated strand board (OSB) was
selected. A comparative study of OSB and solid timber was carried
out to determine the optimum properties that make a material suitable
for use in gridshells. Three parameters were identified to be relevant
in the selection of a material for gridshells. These three parameters
are the strength to stiffness ratio, the flexural stiffness of
commercially available sections, and the variability of material and
section properties. It is shown that when comparing OSB against
solid timber, OSB is a more suitable material for use in gridshells that
are at the smaller end of the scale and that have tight radii of
curvature. Typically, for solid timber materials, stiffness is used as an
indicator for strength and engineered timber is no different. Thus, low
flexural stiffness would mean low flexural strength. However, when
it comes to bending active gridshells, OSB offers a significant
advantage. By the addition of multiple layers, an increased section
size is created, thus endowing the structure with higher stiffness and
higher strength from initial low stiffness and low strength materials
while still maintaining tight radii of curvature. This allows OSB to
compete with solid timber on large scale gridshells. Additionally, a
preliminary sustainability study using a set of sustainability indicators
was carried out to determine the relative sustainability of building a
large-scale gridshell in Ireland with a primary focus on economic
viability but a mention is also given to social and environmental
aspects. For this, the Savill garden gridshell in the UK was used as
the functional unit with the sustainability of the structural roof
skeleton constructed from UK larch solid timber being compared
with the same structure using Irish OSB. Albeit that the advantages of
using commercially available OSB in a bending active gridshell are
marginal and limited to specific gridshell applications, further study
into an optimised engineered timber product is merited.
Abstract: The dissimilar joint between aluminum/titanium
alloys (Al 6082 and Ti G2) were successfully achieved by CO2 laser
welding with a single pass and without filler material using the
overlap joint design. Laser welding parameters ranges combinations
were experimentally determined using Taguchi approach with the
objective of producing welded joint with acceptable welding profile
and high quality of mechanical properties. In this study a joining of
dissimilar Al 6082 / Ti G2 was resulted in three distinct regions
fusion area in the weldment. These regions are studied in terms of its
microstructural characteristics and microhardness which are directly
affecting the welding quality.
The weld metal was mainly composed of martensite alpha prime.
In two different metals in the two different sides of joint HAZ, grain
growth was detected. The microhardness of the joint distribution also
has shown microhardness increasing in the HAZ of two base metals
and a varying microhardness in fusion zone.
Abstract: Enterococci are important inhabitants of the animal
intestine and are widely used in probiotic products. A probiotic strain
is expected to possess several desirable properties in order to exert
beneficial effects. Therefore, the objective of this study was to
isolate, characterize and identify Enterococcus sp. from chicken cecal
and fecal samples to determine potential probiotic properties.
Enterococci were isolated from chicken ceca and feces of thirty three
clinically healthy chickens from a local farm. In vitro studies were
performed to assess antibacterial activity of the isolated LAB (using
agar well diffusion and cell free supernatant broth technique against
Salmonella enterica serotype Enteritidis), survival in acidic
conditions, resistance to bile salts, and their survival during simulated
gastric juice conditions at pH 2.5. Isolates were identified by
biochemical carbohydrate fermentation patterns using an API 50
CHL kit and API ZYM kits and by sequenced 16S rDNA. An isolate
belonging to E. faecium species exhibited inhibitory effect against S.
enteritidis. This isolate producing a clear zone as large as 10.30 mm
or greater and was able to grow in the coculture medium and at the
same time, inhibited the growth S. enteritidis. In addition, E. faecium
exhibited significant resistance under highly acidic conditions at pH
2.5 for 8 h and survived well in bile salt at 0.2% for 24 h and showing
ability to survive in the presence of simulated gastric juice at pH 2.5.
Based on these results, E. faecium isolate fulfills some of the criteria
to be considered as a probiotic strain and therefore, could be used as a
feed additive with good potential for controlling S. Enteritidis in
chickens. However, in vivo studies are needed to determine the safety
of the strain.
Abstract: In this work, we report, a systematic study on the
structural and optical properties of Pr-doped ZnO nanostructures and
PVA:Zn98Pr2O polymer matrix nanocomposites free standing films.
These particles are synthesized through simple wet chemical route
and solution casting technique at room temperature, respectively.
Structural studies carried out by X-ray diffraction method confirm
that the prepared pure ZnO and Pr doped ZnO nanostructures are in
hexagonal wurtzite structure and the microstrain is increased upon
doping. TEM analysis reveals that the prepared materials are in sheet
like nature. Absorption spectra show free excitonic absorption band
at 370 nm and red shift for the Pr doped ZnO nanostructures. The
PVA:Zn98Pr2O composite film exhibits both free excitonic and PVA
absorption bands at 282 nm. Fourier transform infrared spectral
studies confirm the presence of A1 (TO) and E1 (TO) modes of Zn-O
bond vibration and the formation of polymer composite materials.