Abstract: A considerable progress has been achieved in transient
stability analysis (TSA) with various FACTS controllers. But, all
these controllers are associated with single transmission line. This
paper is intended to discuss a new approach i.e. a multi-line FACTS
controller which is interline power flow controller (IPFC) for TSA of
a multi-machine power system network. A mathematical model of
IPFC, termed as power injection model (PIM) presented and this
model is incorporated in Newton-Raphson (NR) power flow
algorithm. Then, the reduced admittance matrix of a multi-machine
power system network for a three phase fault without and with IPFC
is obtained which is required to draw the machine swing curves. A
general approach based on L-index has also been discussed to find
the best location of IPFC to reduce the proximity to instability of a
power system. Numerical results are carried out on two test systems
namely, 6-bus and 11-bus systems. A program in MATLAB has
been written to plot the variation of generator rotor angle and speed
difference curves without and with IPFC for TSA and also a simple
approach has been presented to evaluate critical clearing time for test
systems. The results obtained without and with IPFC are compared
and discussed.
Abstract: In this paper, we present an algorithm for computing a
Schur factorization of a real nonsymmetric matrix with ordered diagonal
blocks such that upper left blocks contains the largest magnitude
eigenvalues. Especially in case of multiple eigenvalues, when matrix
is non diagonalizable, we construct an invariant subspaces with few
additional tricks which are heuristic and numerical results shows the
stability and accuracy of the algorithm.
Abstract: In this paper, the effects of radiation, chemical
reaction and double dispersion on mixed convection heat and mass
transfer along a semi vertical plate are considered. The plate is
embedded in a Newtonian fluid saturated non - Darcy (Forchheimer
flow model) porous medium. The Forchheimer extension and first
order chemical reaction are considered in the flow equations. The
governing sets of partial differential equations are nondimensionalized
and reduced to a set of ordinary differential
equations which are then solved numerically by Fourth order Runge–
Kutta method. Numerical results for the detail of the velocity,
temperature, and concentration profiles as well as heat transfer rates
(Nusselt number) and mass transfer rates (Sherwood number) against
various parameters are presented in graphs. The obtained results are
checked against previously published work for special cases of the
problem and are found to be in good agreement.
Abstract: This study presents an active vibration control
technique to reduce the earthquake responses of a retained structural
system. The proposed technique is a synthesis of the adaptive input
estimation method (AIEM) and linear quadratic Gaussian (LQG)
controller. The AIEM can estimate an unknown system input online.
The LQG controller offers optimal control forces to suppress
wall-structural system vibration. The numerical results show robust
performance in the active vibration control technique.
Abstract: A two dimensional numerical simulation has been
performed for incompressible and compressible fluid flow through
microchannels in slip flow regime. The Navier-Stokes equations have
been solved in conjunction with Maxwell slip conditions for
modeling flow field associated with slip flow regime. The wall
roughness is simulated with triangular microelements distributed on
wall surfaces to study the effects of roughness on fluid flow. Various
Mach and Knudsen numbers are used to investigate the effects of
rarefaction as well as compressibility. It is found that rarefaction has
more significant effect on flow field in microchannels with higher
relative roughness. It is also found that compressibility has more
significant effects on Poiseuille number when relative roughness
increases. In addition, similar to incompressible models the increase
in average fRe is more significant at low Knudsen number flows but
the increase of Poiseuille number duo to relative roughness is sharper
for compressible models. The numerical results have also validated
with some available theoretical and experimental relations and good
agreements have been seen.
Abstract: This paper presents the solution of power economic dispatch (PED) problem of generating units with valve point effects and multiple fuel options using Self-Adaptive Differential Evolution (SDE) algorithm. The global optimal solution by mathematical approaches becomes difficult for the realistic PED problem in power systems. The Differential Evolution (DE) algorithm is found to be a powerful evolutionary algorithm for global optimization in many real problems. In this paper the key parameters of control in DE algorithm such as the crossover constant CR and weight applied to random differential F are self-adapted. The PED problem formulation takes into consideration of nonsmooth fuel cost function due to valve point effects and multi fuel options of generator. The proposed approach has been examined and tested with the numerical results of PED problems with thirteen-generation units including valve-point effects, ten-generation units with multiple fuel options neglecting valve-point effects and ten-generation units including valve-point effects and multiple fuel options. The test results are promising and show the effectiveness of proposed approach for solving PED problems.
Abstract: A new numerical scheme based on the H1-Galerkin mixed finite element method for a class of second-order pseudohyperbolic equations is constructed. The proposed procedures can be split into three independent differential sub-schemes and does not need to solve a coupled system of equations. Optimal error estimates are derived for both semidiscrete and fully discrete schemes for problems in one space dimension. And the proposed method dose not requires the LBB consistency condition. Finally, some numerical results are provided to illustrate the efficacy of our method.
Abstract: In this paper, the effect of bolt clamping force on the fatigue behavior of bolted single lap joints of aluminum alloy 2024- T3 have been studied using numerical finite element method. To do so, a three dimensional model according to the bolted single lap joint has been created and numerical analysis has been carried out using finite element based package. Then the stress distribution and also the slip amplitudes have been calculated in the critical regions and the outcome have been compared with the available experimental fatigue tests results. The numerical results show that in low applied clamping force, the fatigue failure of the specimens occur around the stress concentration location (the bolted hole edge) due to the tensile stresses and thus fatigue crack propagation, but with increase of the clamping force, the fatigue life increases and the cracks nucleate and propagate far from the hole edge because of fretting fatigue. In other words, with the further increase of clamping force value of the joint, the fatigue life reduces due to occurrence of the fretting fatigue in the critical location where the slip amplitude is within its critical occurs earlier.
Abstract: In this paper a new embedded Singly Diagonally
Implicit Runge-Kutta Nystrom fourth order in fifth order method for
solving special second order initial value problems is derived. A
standard set of test problems are tested upon and comparisons on the
numerical results are made when the same set of test problems are
reduced to first order systems and solved using the existing
embedded diagonally implicit Runge-Kutta method. The results
suggests the superiority of the new method.
Abstract: The aeration process via injectors is used to combat
the lack of oxygen in lakes due to eutrophication. A 3D numerical
simulation of the resulting flow using a simplified model is presented.
In order to generate the best dynamic in the fluid with respect to
the aeration purpose, the optimization of the injectors location is
considered. We propose to adapt to this problem the topological
sensitivity analysis method which gives the variation of a criterion
with respect to the creation of a small hole in the domain. The main
idea is to derive the topological sensitivity analysis of the physical
model with respect to the insertion of an injector in the fluid flow
domain. We propose in this work a topological optimization algorithm
based on the studied asymptotic expansion. Finally we present some
numerical results, showing the efficiency of our approach
Abstract: The numerical analytic continuation of a function f(z) = f(x + iy) on a strip is discussed in this paper. The data are only given approximately on the real axis. The periodicity of given data is assumed. A truncated Fourier spectral method has been introduced to deal with the ill-posedness of the problem. The theoretic results show that the discrepancy principle can work well for this problem. Some numerical results are also given to show the efficiency of the method.
Abstract: In this paper, an effective sliding mode design is
applied to chaos synchronization. The proposed controller can make
the states of two identical modified Chua-s circuits globally
asymptotically synchronized. Numerical results are provided to show
the effectiveness and robustness of the proposed method.
Abstract: Three dimensional simulations in tube in tube heat
exchangers are investigated numerically in this study. In these
simulations forced convective heat transfer and laminar flow of
single-phase water are considered. In order to measure heat transfer
parameters in these heat exchangers, FLUENT CFD Solver is used in
this numerical method. For the purpose of creating geometry and
exert boundary and initial conditions in the present model, finite
volume method in Computational Fluid Dynamics is used in this
study. In the present study, at each Z-location, variation of local
temperatures, heat flux and Nusselt number at the whole tube is
investigated in detail. Thereafter, averaged computational Nusselt
number in this model is calculated. In addition, conceivable pressure
drops have been obtained at each Z-location in this model. Then,
pressure drop values in the present model are explored. Finally, all
the numerical results for this kind of heat exchanger will be discussed
precisely.
Abstract: Numerical investigation of flow around a square cylinder are presented using the multi-relaxation-time lattice Boltzmann methods at different Reynolds numbers. A detail analysis are given in terms of time-trace analysis of drag and lift coefficients, power spectra analysis of lift coefficient, vorticity contours visualizations, streamlines and phase diagrams. A number of physical quantities mean drag coefficient, drag coefficient, Strouhal number and root-mean-square values of drag and lift coefficients are calculated and compared with the well resolved experimental data and numerical results available in open literature. The Reynolds numbers affected the physical quantities.
Abstract: In order to obtain an accurate result of the heat transfer
of the rib in the internal cooling Rectangular channel, using separation
of variables, analytical solutions of three dimensional steady-state heat
conduction in rectangular ribs are given by solving three dimensional
steady-state function of the rectangular ribs. Therefore, we can get
solution of three dimensional temperature field in the rib. Based on the
solution, we can get how the Bi number affected on heat transfer.
Furthermore, comparisons of the analytical and numerical results
indicate agreement on temperature field in the rib.
Abstract: In this paper, three dimensional flow characteristic was
presented by a revision of an impeller of an axial turbo fan for
improving the airflow rate and the static pressure. TO consider an
incompressible steady three-dimensional flow, the RANS equations
are used as the governing equations, and the standard k-ε turbulence
model is chosen. The pitch angles of 44°, 54°, 59°, and 64° are
implemented for the numerical model. The numerical results show that
airflow rates of each pitch angle are 1,175 CMH, 1,270 CMH, 1,340
CMH, and 800 CMH, respectively. The difference of the static
pressure at impeller inlet and outlet are 120 Pa, 214 Pa, 242 Pa, and 60
Pa according to respective pitch angles. It means that the 59° of the
impeller pitch angle is optimal to improve the airflow rate and the
static pressure.
Abstract: An adaptive software reliability prediction model
using evolutionary connectionist approach based on Recurrent Radial
Basis Function architecture is proposed. Based on the currently
available software failure time data, Fuzzy Min-Max algorithm is
used to globally optimize the number of the k Gaussian nodes. The
corresponding optimized neural network architecture is iteratively
and dynamically reconfigured in real-time as new actual failure time
data arrives. The performance of our proposed approach has been
tested using sixteen real-time software failure data. Numerical results
show that our proposed approach is robust across different software
projects, and has a better performance with respect to next-steppredictability
compared to existing neural network model for failure
time prediction.
Abstract: We consider a typical problem in the assembly of
printed circuit boards (PCBs) in a two-machine flow shop system to
simultaneously minimize the weighted sum of weighted tardiness and
weighted flow time. The investigated problem is a group scheduling
problem in which PCBs are assembled in groups and the interest is to
find the best sequence of groups as well as the boards within each
group to minimize the objective function value. The type of setup
operation between any two board groups is characterized as carryover
sequence-dependent setup time, which exactly matches with the real
application of this problem. As a technical constraint, all of the
boards must be kitted before the assembly operation starts (kitting
operation) and by kitting staff. The main idea developed in this paper
is to completely eliminate the role of kitting staff by assigning the
task of kitting to the machine operator during the time he is idle
which is referred to as integration of internal (machine) and external
(kitting) setup times. Performing the kitting operation, which is a
preparation process of the next set of boards while the other boards
are currently being assembled, results in the boards to continuously
enter the system or have dynamic arrival times. Consequently, a
dynamic PCB assembly system is introduced for the first time in the
assembly of PCBs, which also has characteristics similar to that of
just-in-time manufacturing. The problem investigated is
computationally very complex, meaning that finding the optimal
solutions especially when the problem size gets larger is impossible.
Thus, a heuristic based on Genetic Algorithm (GA) is employed. An
example problem on the application of the GA developed is
demonstrated and also numerical results of applying the GA on
solving several instances are provided.
Abstract: A new analytical model is developed which provides
close-formed solutions for both transient indoor and envelope
temperature changes in buildings. Time-dependent boundary
temperature is presented as Fourier series which can approximate real
weather conditions. The final close-formed solutions are simple,
concise, and comprehensive. The model was compared with
numerical results and good accuracy was obtained. The model can
be used as design and control guidelines in engineering applications
for analysing mechanical heat transfer properties for buildings.
Abstract: Westudy a dual-channel supply chain under
decentralized setting in which manufacturer sells to retailer and to
customers directly usingan online channel. A customer chooses the
purchase-channel based on price and service quality. Also, to buy
product from the retail store, the customer incurs a transportation cost
influenced by the fluctuating gasoline cost. Both companies are under
the revenue sharing contract. In this contract the retailer share a
portion of the revenue to the manufacturer while the manufacturer
will charge the lower wholesales price. The numerical result shows
that the effects of gasoline costs, the revenue sharing ratio and the
wholesale price play an important role in determining optimal prices.
The result shows that when the gasoline price fluctuatesthe optimal
on-line priceis relatively stable while the optimal retail price moves
in the opposite direction of the gasoline prices.