Abstract: The gel-supported precipitation (GSP) process can be
used to make spherical particles (spherules) of nuclear fuel,
particularly for very high temperature reactors (VHTR) and even for
implementing the process called SPHEREPAC. In these different
cases, the main characteristics are the sphericity of the particles to be
manufactured and the control over their grain size. Nonetheless,
depending on the specifications defined for these spherical particles,
the GSP process has intrinsic limits, particularly when fabricating
very small particles. This paper describes the use of secondary
fragmentation (water, water/PVA and uranyl nitrate) on solid
surfaces under varying temperature and vibration conditions to assess
the relevance of using this new technique to manufacture very small
spherical particles by means of a modified GSP process. The
fragmentation mechanisms are monitored and analysed, before the
trends for its subsequent optimised application are described.
Abstract: The study of piezoelectric material in the past was in
T-Domain form; however, no one has studied piezoelectric material in the S-Domain form. This paper will present the piezoelectric material in the transfer function or S-Domain model. S-Domain is a
well known mathematical model, used for analyzing the stability of the material and determining the stability limits. By using S-Domain
in testing stability of piezoelectric material, it will provide a new tool for the scientific world to study this material in various forms.
Abstract: This paper developed the c-Chart based on a Zero- Inflated Poisson (ZIP) processes that approximated by a geometric distribution with parameter p. The p estimated that fit for ZIP distribution used in calculated the mean, median, and variance of geometric distribution for constructed the c-Chart by three difference methods. For cg-Chart, developed c-Chart by used the mean and variance of the geometric distribution constructed control limits. For cmg-Chart, the mean used for constructed the control limits. The cme- Chart, developed control limits of c-Chart from median and variance values of geometric distribution. The performance of charts considered from the Average Run Length and Average Coverage Probability. We found that for an in-control process, the cg-Chart is superior for low level of mean at all level of proportion zero. For an out-of-control process, the cmg-Chart and cme-Chart are the best for mean = 2, 3 and 4 at all level of parameter.
Abstract: In this study rack systems that are structural storage
units of warehouses have been analyzed as structural with Finite
Element Method (FEA). Each cell of discussed rack system storages
pallets which have from 800 kg to 1000 kg weights and
0.80x1.15x1.50 m dimensions. Under this load, total deformations
and equivalent stresses of structural elements and principal stresses,
tensile stresses and shear stresses of connection elements have been
analyzed. The results of analyses have been evaluated according to
resistance limits of structural and connection elements. Obtained
results have been presented as visual and magnitude.
Abstract: To comply with the international human right
legislation concerning the freedom of movement, transport systems
are required to be made accessible in order that all citizens, regardless
of their physical condition, have equal possibilities to use them. In
Hungary, apparently there is a considerable default in the
improvement of accessible public transport. This study is aiming to
overview the current Hungarian situation and to reveal the reasons of
the deficiency. The result shows that in spite of the relatively
favourable juridical background linked to the accessibility needs and
to the rights of persons with disabilities there is a strong delay in
putting all in practice in the field of public transport. Its main reason
is the lack of financial resource and referring to this the lack of
creating mandatory regulations. In addition to this the proprietary
rights related to public transport are also variable, which also limits
the improvement possibilities. Consequently, first of all an accurate
and detailed regulatory procedure is expected to change the present
unfavourable situation and to create the conditions of the fast
realization, which is already behind time.
Abstract: The aim of this work is to analyze a viscous flow in
the axisymmetric nozzle taken into account the mesh size both in the
free stream and into the boundary layer. The resolution of the Navier-
Stokes equations is realized by using the finite volume method to
determine the supersonic flow parameters at the exit of convergingdiverging
nozzle. The numerical technique uses the Flux Vector
Splitting method of Van Leer. Here, adequate time stepping
parameter, along with CFL coefficient and mesh size level is selected
to ensure numerical convergence. The effect of the boundary layer
thickness is significant at the exit of the nozzle. The best solution is
obtained with using a very fine grid, especially near the wall, where
we have a strong variation of velocity, temperature and shear stress.
This study enabled us to confirm that the determination of boundary
layer thickness can be obtained only if the size of the mesh is lower
than a certain value limits given by our calculations.
Abstract: In this paper, a novel method using Bees Algorithm is proposed to determine the optimal allocation of FACTS devices for maximizing the Available Transfer Capability (ATC) of power transactions between source and sink areas in the deregulated power system. The algorithm simultaneously searches the FACTS location, FACTS parameters and FACTS types. Two types of FACTS are simulated in this study namely Thyristor Controlled Series Compensator (TCSC) and Static Var Compensator (SVC). A Repeated Power Flow with FACTS devices including ATC is used to evaluate the feasible ATC value within real and reactive power generation limits, line thermal limits, voltage limits and FACTS operation limits. An IEEE30 bus system is used to demonstrate the effectiveness of the algorithm as an optimization tool to enhance ATC. A Genetic Algorithm technique is used for validation purposes. The results clearly indicate that the introduction of FACTS devices in a right combination of location and parameters could enhance ATC and Bees Algorithm can be efficiently used for this kind of nonlinear integer optimization.
Abstract: Modern highly automated production systems faces
problems of reliability. Machine function reliability results in
changes of productivity rate and efficiency use of expensive
industrial facilities. Predicting of reliability has become an important
research and involves complex mathematical methods and
calculation. The reliability of high productivity technological
automatic machines that consists of complex mechanical, electrical
and electronic components is important. The failure of these units
results in major economic losses of production systems. The
reliability of transport and feeding systems for automatic
technological machines is also important, because failure of transport
leads to stops of technological machines. This paper presents
reliability engineering on the feeding system and its components for
transporting a complex shape parts to automatic machines. It also
discusses about the calculation of the reliability parameters of the
feeding unit by applying the probability theory. Equations produced
for calculating the limits of the geometrical sizes of feeders and the
probability of sticking the transported parts into the chute represents
the reliability of feeders as a function of its geometrical parameters.
Abstract: Studying literature theme in the fields of tourism and
sustainable development and its importance in today world and their
criteria in architecture, here in this article we will also study the area
where the selected site is located; beside the Aab-Ask Village located
in Larijan region in Mazandaran province on the way to Haraz – one
of the tourism routes of Iran. After these studies by analyzing the
site, its strong potentials – such as mineral water springs (hot
springs), geothermal, landscapes and ideal climate - as a tourist
attraction spot in the region, and considering sustainable
development criteria – with regard to limits and available facilities –
a plan was offered that could change the region to provide the needs
of local people and in addition change it to a place where tourism
services is offered to the visitors and make it an acceptable sample of
stable building in Iran. Finally the reason to make design for this
complex is recovery of natural and historical values of Aab-Ask area
regarding development and sustainable architecture criteria in the
form of a functional sample which can be a suitable place to fulfill
this goal for having lots of strong points in attracting cultural and
sustainable tourist.
Abstract: Three-phase induction machines are today a standard
for industrial electrical drives. Cost, reliability, robustness and maintenance free operation are among the reasons these machines are
replacing dc drive systems. The development of power electronics
and signal processing systems has eliminated one of the greatest
disadvantages of such ac systems, which is the issue of control. With
modern techniques of field oriented vector control, the task of
variable speed control of induction machines is no longer a
disadvantage. The need to increase system performance, particularly
when facing limits on the power ratings of power supplies and
semiconductors, motivates the use of phase number other than three,
In this paper a novel scheme of connecting two, three phase
induction motors in parallel fed by two inverters; viz. VSI and CSI
and their vector control is presented.
Abstract: This study examined the effects of 8-week Pilates training program on limits of stability (LOS) and abdominal muscle strength in young dancers. Twenty-four female volunteered and randomly assigned as experimental group (EG) or control group (CG). All subjects received the same dance lessons but the EG underwent an extra Pilates mat exercises for 40 minutes, three times a week, for 8 weeks. LOS was evaluated by the Biodex Balance System and the abdominal strength was measured by 30/60 seconds sit-ups test. One factor ANCOVA was used to examine the differences between groups after training. The results showed that the overall LOS scores at levels 2/8 and the 30/60 seconds sit-ups for the EG group pre- and post-training were changed from 22/38 % to 31/51 % and 20/33 times to 24/42 times, respectively. The study demonstrated that 8-week Pilates training can improve the LOS performance and abdominal strength in young dancers.
Abstract: In this paper the optimal control strategy for
Permanent Magnet Synchronous Motor (PMSM) based drive system
is presented. The designed full optimal control is available for speed
operating range up to base speed. The optimal voltage space-vector
assures input energy reduction and stator loss minimization,
maintaining the output energy in the same limits with the
conventional PMSM electrical drive. The optimal control with three
components is based on the energetically criteria and it is applicable
in numerical version, being a nonrecursive solution. The simulation
results confirm the increased efficiency of the optimal PMSM drive.
The properties of the optimal voltage space vector are shown.
Abstract: Thermoacoustic instabilities in combustors have
remained a topic of investigation for over a few decades due to the
challenges it posses to the operation of low emission gas turbines.
For combustors burning liquid fuel, understanding the cause-andeffect
relationship between spray combustion dynamics and
thermoacoustic oscillations is imperative for the successful
development of any control methodology for its mitigation. The
paper presents some very unique operating characteristics of a
kerosene-fueled diffusion type combustor undergoing limit-cycle
oscillations. Combustor stability limits were mapped using three
different-sized injectors. The results show that combustor instability
depends on the characteristics of the fuel spray. A simple analytic
analysis is also reported in support of a plausible explanation for the
unique combustor behavior. The study indicates that high amplitude
acoustic pressure in the combustor may cause secondary breakdown
of fuel droplets resulting in premixed pre-vaporized type burning of
the diffusion type combustor.
Abstract: Game theory could be used to analyze the conflicted
issues in the field of information hiding. In this paper, 2-phase game
can be used to build the embedder-attacker system to analyze the
limits of hiding capacity of embedding algorithms: the embedder
minimizes the expected damage and the attacker maximizes it. In the
system, the embedder first consumes its resource to build embedded
units (EU) and insert the secret information into EU. Then the attacker
distributes its resource evenly to the attacked EU. The expected
equilibrium damage, which is maximum damage in value from the
point of view of the attacker and minimum from the embedder against
the attacker, is evaluated by the case when the attacker attacks a
subset from all the EU. Furthermore, the optimal equilibrium capacity
of hiding information is calculated through the optimal number of EU
with the embedded secret information. Finally, illustrative examples
of the optimal equilibrium capacity are presented.
Abstract: Fuzzy logic approach is used in this study to predict
the tractive performance in terms of traction force, and motion
resistance for an intelligent air cushion track vehicle while it operates
in the swamp peat. The system is effective to control the intelligent
air –cushion system with measuring the vehicle traction force (TF),
motion resistance (MR), cushion clearance height (CH) and cushion
pressure (CP). Sinkage measuring sensor, magnetic switch, pressure
sensor, micro controller, control valves and battery are incorporated
with the Fuzzy logic system (FLS) to investigate experimentally the
TF, MR, CH, and CP. In this study, a comparison for tractive
performance of an intelligent air cushion track vehicle has been
performed with the results obtained from the predicted values of FLS
and experimental actual values. The mean relative error of actual and
predicted values from the FLS model on traction force, and total
motion resistance are found as 5.58 %, and 6.78 % respectively. For
all parameters, the relative error of predicted values are found to be
less than the acceptable limits. The goodness of fit of the prediction
values from the FLS model on TF, and MR are found as 0.90, and
0.98 respectively.
Abstract: Electricity market activities and a growing demand for electricity have led to heavily stressed power systems. This requires operation of the networks closer to their stability limits. Power system operation is affected by stability related problems, leading to unpredictable system behavior. Voltage stability refers to the ability of a power system to sustain appropriate voltage levels through large and small disturbances. Steady-state voltage stability is concerned with limits on the existence of steady-state operating points for the network. FACTS devices can be utilized to increase the transmission capacity, the stability margin and dynamic behavior or serve to ensure improved power quality. Their main capabilities are reactive power compensation, voltage control and power flow control. Among the FACTS controllers, Static Var Compensator (SVC) provides fast acting dynamic reactive compensation for voltage support during contingency events. In this paper, voltage stability assessment with appropriate representations of tap-changer transformers and SVC is investigated. Integrating both of these devices is the main topic of this paper. Effect of the presence of tap-changing transformers on static VAR compensator controller parameters and ratings necessary to stabilize load voltages at certain values are highlighted. The interrelation between transformer off nominal tap ratios and the SVC controller gains and droop slopes and the SVC rating are found. P-V curves are constructed to calculate loadability margins.
Abstract: Most of the well known methods for generating
Gaussian variables require at least one standard uniform distributed
value, for each Gaussian variable generated. The length of the
random number generator therefore, limits the number of
independent Gaussian distributed variables that can be generated
meanwhile the statistical solution of complex systems requires a
large number of random numbers for their statistical analysis. We
propose an alternative simple method of generating almost infinite
number of Gaussian distributed variables using a limited number of
standard uniform distributed random numbers.
Abstract: In order to meet the limits imposed on automotive
emissions, engine control systems are required to constrain air/fuel
ratio (AFR) in a narrow band around the stoichiometric value, due to
the strong decay of catalyst efficiency in case of rich or lean mixture.
This paper presents a model of a sample spark ignition engine and
demonstrates Simulink-s capabilities to model an internal combustion
engine from the throttle to the crankshaft output. We used welldefined
physical principles supplemented, where appropriate, with
empirical relationships that describe the system-s dynamic behavior
without introducing unnecessary complexity. We also presents a PID
tuning method that uses an adaptive fuzzy system to model the
relationship between the controller gains and the target output
response, with the response specification set by desired percent
overshoot and settling time. The adaptive fuzzy based input-output
model is then used to tune on-line the PID gains for different
response specifications. Experimental results demonstrate that better
performance can be achieved with adaptive fuzzy tuning relative to
similar alternative control strategies. The actual response
specifications with adaptive fuzzy matched the desired response
specifications.
Abstract: This paper sets forth the possibility and importance about applying Data Mining in Web logs mining and shows some problems in the conventional searching engines. Then it offers an improved algorithm based on the original AprioriAll algorithm which has been used in Web logs mining widely. The new algorithm adds the property of the User ID during the every step of producing the candidate set and every step of scanning the database by which to decide whether an item in the candidate set should be put into the large set which will be used to produce next candidate set. At the meantime, in order to reduce the number of the database scanning, the new algorithm, by using the property of the Apriori algorithm, limits the size of the candidate set in time whenever it is produced. Test results show the improved algorithm has a more lower complexity of time and space, better restrain noise and fit the capacity of memory.
Abstract: Soft clays are defined as cohesive soil whose water
content is higher than its liquid limits. Thus, soil-cement mixing is
adopted to improve the ground conditions by enhancing the strength
and deformation characteristics of the soft clays. For the above
mentioned reasons, a series of laboratory tests were carried out to
study some fundamental mechanical properties of cement stabilized
soft clay. The test specimens were prepared by varying the portion of
ordinary Portland cement to the soft clay sample retrieved from the
test site of RECESS (Research Centre for Soft Soil). Comparisons
were made for both homogeneous and columnar system specimens
by relating the effects of cement stabilized clay of for 0, 5 and 10 %
cement and curing for 3, 28 and 56 days. The mechanical properties
examined included one-dimensional compressibility and undrained
shear strength. For the mechanical properties, both homogeneous and
columnar system specimens were prepared to examine the effect of
different cement contents and curing periods on the stabilized soil.
The one-dimensional compressibility test was conducted using an
oedometer, while a direct shear box was used for measuring the
undrained shear strength. The higher the value of cement content, the
greater is the enhancement of the yield stress and the decrease of
compression index. The value of cement content in a specimen is a
more active parameter than the curing period.