Abstract: The present paper studies a structure consisting of a periodic metallic grating, coated on a dielectric spacer atop an opaque metal substrate, using coherent thermal emission source in the infrared region. It has been theoretically demonstrated that by exciting surface magnetic polaritons between metallic gratings and an opaque metallic film, separated by a dielectric spacer, large emissivity peaks are almost independent of the emission angle and they can be achieved at the resonance frequencies. The reflectance spectrum of the proposed structure shows two resonances dip, which leads to a sharp emissivity peak. The relations of the reflection and absorption properties and the influence of geometric parameters on the radiative properties are investigated by rigorous coupled-wave analysis (RCWA). The proposed structure can be easily constructed, using micro/nanofabrication and can be used as the coherent thermal emission source.
Abstract: In this study, WC-Ni-based cemented carbides having different nickel contents were used as the substrate for cutting tool materials. Hardened steel was turned by a (Ti,W,Si)N-coated WC-Ni-based cemented carbide tool, and the tool wear was experimentally investigated. The following results were obtained: (1) In the (Ti,W,Si)N-coated WC-Ni-based cemented carbide, the hardness of the coating film was not much different from the content of the binding material, Ni, and the adhesion strength increased with a decrease in Ni content. (2) There is little difference between the wear progress of the (Ti,W,Si)N-coated WC-7%Ni-based cemented carbide tool and that of the (Ti,W,Si)N-coated WC-6%Co-based cemented carbide tool. (3) The wear progress of the (Ti,W,Si)N-coated WC-Ni-based cemented carbide became slower with a decrease in Ni content.
From the above, it is has become clear that WC-Ni-based cemented carbide can be used as a substrate for cutting tool materials.
Abstract: Chitosan is a derivative of chitin, a compound usually
isolated from the shells of some crustaceans such as crab, lobster and
shrimp. It has biocompatible, biodegradable, and antimicrobial
properties. To use these properties of chitosan in biomedical fields,
chitosan films (1%, 2%, 3% and 4%) were prepared by using l%
lactic acid as solvent. The effects of chitosan films on tensile
strength, elongation at break, degree of swelling, thickness,
morphology, allergic and irritation reactions and antibacterial
property were evaluated. Staphylococcus aureus and Escherichia coli
were used as tested microorganisms. In vivo wound healing activities
of chitosan films were investigated using mice model. As results,
Chitosan films have similar appearance and good swelling properties
and 4% chitosan film showed the better swelling activity and the
greatest elongation ratio than the other chitosan films. They also
showed their good activity of wound healing in mice model.
Moreover, the results showed that the films did not produce any
unwilling symptoms (allergy or irritation). In conclusion, it is evident
that the chitosan film has the potentiality to use as wound healing
biofilms in the biomedical fields.
Abstract: The objective of the present study was to determine quality parameters changes of red wine marinade marinated venison during storage. Beef as a control was analysed. Protein, fat, moisture and pH content dynamics as well microbiological quality was analyzed. The meat pieces were marinated in red wine marinade at 4±2ºC temperature for 48±1h. Marinated meat was placed in polypropylene trays, hermetically sealed with high barrier polymer film Multibarrier 60 under modified atmosphere (CO2 40%+N2 60%) without and with oxygen absorber sachets, as a control packaging in air ambiance packed marinated venison and beef was used. Meat samples were analyzed after 0, 4, 7, 11 and 14 days of storage. During the storage of meat, protein and moisture content significantly (p
Abstract: The present study represents the occupational radiation doses received by selected workers of Nuclear Institute of Medicine and Radiotherapy (NIMRA) Jamshoro Pakistan and conducted to discuss about how we be careful and try to avoid make ourselves overconscious. Film badges with unique identification number were issued to radiation worker to detect occupational radiation doses. In this study, only 08 workers with high radiation doses were assessed amongst 35 radiation workers during the period of January 2012 to December 2012. The selected radiation workers’ occupational doses were according to designated work areas and in the range of 1.21 to 7.78 mSv (mili Sieveret) out of the annual dose limit of 20 mSv. By the comparison of different studies and earth’s HNBR (High Natural Background Radiation) locations’ doses, it is concluded that the worker’s high doses are of magnitude of HNBR Regions and were in the acceptable range of National and International regulatory bodies so we must not to show any type of overconsciousness but be careful in handling the radioactive sources.
Abstract: In this study tree types of multilayer gas barrier plastic packaging films were compared using life cycle assessment as a tool for resource efficient and environmentally low-impact materials selection. The first type of multilayer packaging film (PET-AlOx/LDPE) consists of polyethylene terephthalate with barrier layer AlOx (PET-AlOx) and low density polyethylene (LDPE). The second type of polymer film (PET/PE-EVOH-PE) is made of polyethylene terephthalate (PET) and co-extrusion film PE-EVOH-PE as barrier layer. And the third one type of multilayer packaging film (PET-PVOH/LDPE) is formed from polyethylene terephthalate with barrier layer PVOH (PET-PVOH) and low density polyethylene (LDPE).
All of analyzed packaging has significant impact to resource depletion, because of raw materials extraction and energy use and production of different kind of plastics. Nevertheless the impact generated during life cycle of functional unit of II type of packaging (PET/PE-EVOH-PE) was about 25% lower than impact generated by I type (PET-AlOx/LDPE) and III type (PET-PVOH/LDPE) of packaging.
Result revealed that the contribution of different gas barrier type to the overall environmental problem of packaging is not significant. The impact are mostly generated by using energy and materials during raw material extraction and production of different plastic materials as plastic polymers material as PE, LDPE and PET, but not gas barrier materials as AlOx, PVOH and EVOH.
The LCA results could be useful in different decision-making processes, for selecting resource efficient and environmentally low-impact materials.
Abstract: According to synthetic plastics obtained from petroleum cause some environmental problems. Therefore, degradable plastics become widely used and studied for replacing the synthetic plastic waste. A biopolymer of poly hydroxybutyrate-co-hydroxyvalerate (PHBV) is subgroups of a main kind of polyhydroxyalkanoates (PHAs). Naturally, PHBV is hard, brittle and low flexible while natural rubber (NR) is high elastic latex. Then, they are blended and the biodegradation of the blended PHBV and NR films were examined in soil environment. The results showed that the degradation occurs predominantly in the bulk of the samples. The order of biodegradability was shown as follows: PHBV> PHBV/NR> NR. After biodegradation, the blended films were characterized by appearance analysis such as Scanning Electron Microscope (SEM), Fourier transform infrared spectroscopy (FTIR) and Differential Scanning Calorimetry (DSC). It was found that the biodegradation mainly occurred at the polymer surface.
Abstract: An optical chemical sensing film based on
immobilizing of 1,1′- diethyl 2,2′-cyanine (pseudocyanine iodide) in
nafion film was developed for the determination of Fe(III). The
sensing film was homogeneous, transparent, and mechanically stable.
Decrease of the absorbance measured at 518 nm was observed when
the sensing film was immersed in a solution of Fe(III). The optimum
response of the sensing film to Fe(III) was obtained in a solution with
pH 4.0. Linear calibration curve over an Fe(III) concentration range
of 1-30 ppm with a limit of detection of 0.71 ppm was obtained.
Cd(II) is the major interference. The sensing film exhibited good
stability for 2 months and high reproducibility. The proposed method
was applied for the determination of Fe(III) in water samples with
satisfactory results.
Abstract: Preparation of hydrogel based on carrageenan
extracted from Kappaphycus alvarezii was conducted with film
immersion in glutaraldehyde solution (GA 4%w/w) for 2min and
then followed by thermal curing at 110°C for 25min. The method of
carrageenan recovery strongly determines the properties of
crosslinked carrageenan. Hydrogel obtained from alkali treated
carrageenan showed higher swelling ability compared to hydrogel
from nonalkali treated carrageenan. Hydrogel from alkali treated
showed the ability of sensitive to pH media.
Abstract: The deposition of diamond films on a Si3N4 substrate
is an attractive technique for industrial applications because of the
excellent properties of diamond. Pretreatment of substrate is very
important prior to diamond deposition to promote nucleation and
adhesion between coating and substrate. Deposition of
nanocrystalline diamonds films on silicon nitride substrate have been
carried out by HF-CVD technique using mixture of methane and
hydrogen gases. Different pretreatment of substrate including
chemical etching consists of hot acid etching and basic etching and
mechanical etching were used to study the quality of diamond formed
on the substrate. The structure and morphology of diamond coating
have been studied using X-ray Diffraction (XRD) and Scanning
Electron Microscope (SEM) while diamond film quality has been
characterized using Raman spectroscopy. AFM was used to
investigate the effect of chemical etching and mechanical
pretreatment on the surface roughness of the substrates and the
resultant morphology of nanocrystalline diamond. It was found that
diamond film deposited on as-received, basic etched and grinded
substrate shows the morphology of cauliflower while blasted and
acidic etched substrates produce smooth, continuous diamond film.
However, the Raman investigation did not show any deviation in
quality of diamond film for any pretreatment.
Abstract: In this study we present the effect of elevated
temperatures from 300K to 400K on the electrical properties of
copper Phthalocyanine (CuPc) based organic field effect transistors
(OFET). Thin films of organic semiconductor CuPc (40nm) and
semitransparent Al (20nm) were deposited in sequence, by vacuum
evaporation on a glass substrate with previously deposited Ag source
and drain electrodes with a gap of 40 μm. Under resistive mode of
operation, where gate was suspended it was observed that drain
current of this organic field effect transistor (OFET) show an
increase with temperature. While in grounded gate condition metal
(aluminum) – semiconductor (Copper Phthalocyanine) Schottky
junction dominated the output characteristics and device showed
switching effect from low to high conduction states like Zener diode
at higher bias voltages. This threshold voltage for switching effect
has been found to be inversely proportional to temperature and shows
an abrupt decrease after knee temperature of 360K. Change in
dynamic resistance (Rd = dV/dI) with respect to temperature was
observed to be -1%/K.
Abstract: The use of plastic materials in agriculture causes
serious hazards to the environment. The introduction of biodegradable materials, which can be disposed directly into the soil
can be one possible solution to this problem. In the present research results of experimental tests carried out on biodegradable film
fabricated from natural waste (corn husk) are presented. The film was
characterized by Fourier transform infrared spectroscopy (FTIR),
differential scanning calorimeter (DSC), thermal gravimetric analysis
(TGA) and atomic force microscope (AFM) observation. The film is
shown to be readily degraded within 7-9 months under controlled soil
conditions, indicating a high biodegradability rate. The film
fabricated was use to produce biodegradable pot (BioPot) for
seedlings plantation. The introduction and the expanding use of
biodegradable materials represent a really promising alternative for
enhancing sustainable and environmentally friendly agricultural
activities.
Abstract: Polypropylene blended with natural oil and pigment additives has been studied. Different formulations for each compound were made into polybag used for cultivation of oil palm seedlings for strength and mechanical properties studies. One group of sample was exposed under normal sunlight to initiate degradation and another group of sample was placed under shaded area for five months. All samples were tested for tensile strength to determine the degradation effects. The tensile strength of directly exposed sunlight samples and shaded area showed up to 50% and 25% degradation respectively. However, similar reduction of Young’s modulus for all samples was found for both exposures. Structural investigations were done using FTIR to detect deformation. The natural additives that were used in the studies were all natural and environmental friendly
Abstract: In this paper, some experiments of liquid dispersion flow driven by explosion in vertical plane were carried out using a liquid explosive dispersion device with film cylindrical constraints. The separated time series describing the breakup shape and dispersion process of liquid were recorded with high speed CMOS camera. The experimental results were analyzed and some essential characteristics of liquid dispersing flow are presented.
Abstract: Structured catalysts formed from the growth of
zeolites on substrates is an area of increasing interest due to the
increased efficiency of the catalytic process, and the ability to
provide superior heat transfer and thermal conductivity for both
exothermic and endothermic processes.
However, the generation of structured catalysts represents a
significant challenge when balancing the relationship variables
between materials properties and catalytic performance, with the
Na2O, H2O and Al2O3 gel composition paying a significant role in
this dynamic, thereby affecting the both the type and range of
application.
The structured catalyst films generated as part of this
investigation have been characterised using a range of techniques,
including X-ray diffraction (XRD), Electron microscopy (SEM),
Energy Dispersive X-ray analysis (EDX) and Thermogravimetric
Analysis (TGA), with the transition from oxide-on-alloy wires to
hydrothermally synthesised uniformly zeolite coated surfaces being
demonstrated using both SEM and XRD. The robustness of the
coatings has been ascertained by subjecting these to thermal cycling
(ambient to 550oC), with the results indicating that the synthesis time
and gel compositions have a crucial effect on the quality of zeolite
growth on the FeCrAlloy wires.
Finally, the activity of the structured catalyst was verified by a
series of comparison experiments with standard zeolite Y catalysts in
powdered pelleted forms.
Abstract: Single photon detectors have been fabricated NbN
nano wire. These detectors are fabricated from high quality, ultra
high vacuum sputtered NbN thin films on a sapphire substrate. In this
work a typical schematic of the nanowire Single Photon Detector
structure and then driving and measurement electronic circuit are
shown.
The response of superconducting nanowire single photon detectors
during a photo detection event, is modeled by a special electrical
circuits (two circuit).
Finally, current through the wire is calculated by solving
equations of models.
Abstract: Silver-exchanged zeolites and clays are used in
polymer composites to confer broad-spectrum antimicrobial
properties on a range of functional materials. Tobermorite is a layer
lattice mineral whose potential as a carrier for Ag+ ions in
antibacterial composites has not yet been investigated. Accordingly,
in this study, synthetic tobermorite was ion-exchanged with 10 wt%
silver ions and the resulting material was incorporated into a
composite film with chitosan. Chitosan is a biocompatible,
biodegradable derivative of chitin, a polysaccharide obtained from
the shells of crustaceans. The solvent-cast Ag+-exchanged
tobermorite-chitosan films were found to exhibit antimicrobial action
against Staphylococcus aureus, Escherichia coli and Pseudomonas
aeruginosa.
Abstract: Hollywood has produced various blockbusters on the
subject of disasters. Entering the 2000s, disaster films began to be
produced in the East Asian region as well, and as most of them were
successful, disaster films have settled as a popular genre in the region.
East Asian disaster films utilize a plot structure similar to Hollywood
films but, at the same time, represent East Asian people-s unique value
system. East Asian people-s social behavior pattern defined as
collectivism is a characteristic that distinguishes this region from other
cultural regions. In order to examine Confucian culture in disaster
films on the premise of the difference, the author conducts this
research as follows.This study first reviews the concepts disaster and
disaster film, and understands the genre through analyzing the
narrative structure and style. In addition, it discusses collectivism, a
characteristic of the East Asian region distinguished from the West,
and investigates Confucian culture in films and examines differences
among Korean, Chinese and Japanese Confucianism. Films selected
for this study are Tidal Wave (Korea, 2009), After Shock (China,
2006), and The Sinking of Japan (Japan, 2006). Using the characters in
these films, we analyze how Confucian thought is described and
reproduced.
Abstract: Water borne polyurethane (PU) based on newly prepared hyperbranched poly (amine-ester) (HBPAE) was applied and evaluated as organic coating material. HBPAE was prepared through one-pot synthesis between trimethylol propane as a core and AB2 branched monomer which was obtained via Michal addition of methyl methacrylate (MMA) and diethanol amine (DEA). PU was prepared from HBPAE using different ratios of toluene diisocyanate (TDI) to form cured coating film. The prepared HBPAE was characterized using; GPC, FT-IR and 1H-NMR. The mechanical properties (impact, hardness, adhesion, and flexibility), thermal properties (DSC and TGA) and chemical resistance of the applied film were estimated. The results indicated 50% of TDI is the selected ratio. This formulation represents a promising candidate to be used as coating material.
Abstract: This paper aims to scale up Dye-sensitized Solar Cell
(DSSC) production using a commonly available industrial material –
stainless steel - and industrial plasma equipment. A working DSSC
electrode formed by (1) coating titania nanotube (TiO2 NT) film on
304 stainless steel substrate using a plasma spray technique; then, (2)
filling the nano-pores of the TiO2 NT film using a TiF4 sol-gel method.
A DSSC device consists of an anode absorbed photosensitive dye
(N3), a transparent conductive cathode with platinum (Pt)
nano-catalytic particles adhered to its surface, and an electrolytic
solution sealed between the anode and the transparent conductive
cathode. The photo-current conversion efficiency of the DSSC sample
was tested under an AM 1.5 Solar Simulator. The sample has a short
current (Isc) of 0.83 mA cm-2, open voltage (Voc) of 0.81V, filling
factor (FF) of 0.52, and conversion efficiency (η) of 2.18% on a 0.16
cm2 DSSC work-piece.