Abstract: Higher order ΔΣ Modulator (DSM) is basically an
unstable system. The approximate conditions for stability cannot be
used for the design of a DSM for industrial applications where risk is
involved. The existing second order, single stage, single bit, unity
feedback gain , discrete DSM cannot be used for the normalized full
range (-1 to +1) of an input signal since the DSM becomes unstable
when the input signal is above ±0.55. The stability is also not
guaranteed for input signals of amplitude less than ±0.55. In the
present paper, the above mentioned second order DSM is modified
with input signal dependent forward path gain. The proposed DSM is
suitable for industrial applications where one needs the digital
representation of the analog input signal, during each sampling
period. The proposed DSM can operate almost for the full range of
input signals (-0.95 to +0.95) without causing instability, assuming
that the second integrator output should not exceed the circuit supply
voltage, ±15 Volts.
Abstract: In this paper we describe the Levenvberg-Marquardt
(LM) algorithm for identification and equalization of CDMA
signals received by an antenna array in communication channels.
The synthesis explains the digital separation and equalization of
signals after propagation through multipath generating intersymbol
interference (ISI). Exploiting discrete data transmitted and three
diversities induced at the reception, the problem can be composed
by the Block Component Decomposition (BCD) of a tensor of
order 3 which is a new tensor decomposition generalizing the
PARAFAC decomposition. We optimize the BCD decomposition by
Levenvberg-Marquardt method gives encouraging results compared to
classical alternating least squares algorithm (ALS). In the equalization
part, we use the Minimum Mean Square Error (MMSE) to perform
the presented method. The simulation results using the LM algorithm
are important.
Abstract: The Roma (Gypsies) is a transnational minority with a
high degree of consanguineous marriages. Similar to other
genetically isolated founder populations, the Roma harbor a number
of unique or rare genetic disorders. This paper discusses about a rare
form of Charcot-Marie-Tooth disease – type 4G (CMT4G), also
called Hereditary Motor and Sensory Neuropathy type Russe, an
autosomal recessive disease caused by mutation private to Roma
characterized by abnormally increased density of non-myelinated
axons. CMT4G was originally found in Bulgarian Roma and in 2009
two putative causative mutations in the HK1 gene were identified.
Since then, several cases were reported in Roma families mainly
from Bulgaria and Spain. Here we present a Slovak Roma family in
which CMT4G was diagnosed on the basis of clinical examination
and genetic testing. This case is a further proof of the role of the HK1
gene in pathogenesis of the disease. It confirms that mutation in the
HK1 gene is a common cause of autosomal recessive CMT disease in
Roma and should be considered as a common part of a diagnostic
procedure.
Abstract: Monoamine oxidase A gene (MAOA) is suggested to
be a candidate gene implicated in many neuropsychiatric disorders,
including autism spectrum disorder (ASD). This meta-analytic review
evaluates the relationship between ASD and MAOA markers such as
30 bp variable number tandem repeats in the promoter region
(uVNTR) and single nucleotide polymorphisms (SNPs) by using
findings from recently published studies. It seems that in Caucasian
males, the risk of developing ASD increase with the presence of 4-
repeat allele in the promoter region of MAOA gene whereas no
differences were found between autistic patients and controls in
Egyptian, West Bengal and Korean population. Some studies point to
the importance of specific haplotype groups of SNPs and interaction
of MAOA with others genes (e. g. FOXP2 or SRY). The results of
existing studies are insufficient and further research is needed.
Abstract: Alkylated silicon nanocrystals (C11-SiNCs) were
prepared successfully by galvanostatic etching of p-Si(100) wafers
followed by a thermal hydrosilation reaction of 1-undecene in
refluxing toluene in order to extract C11-SiNCs from porous silicon.
Erbium trichloride was added to alkylated SiNCs using a simple
mixing chemical route. To the best of our knowledge, this is the first
investigation on mixing SiNCs with erbium ions (III) by this
chemical method. The chemical characterization of C11-SiNCs and
their mixtures with Er3+(Er/C11-SiNCs) were carried out using X-ray
photoemission spectroscopy (XPS). The optical properties of C11-
SiNCs and their mixtures with Er3+ were investigated using Raman
spectroscopy and photoluminescence (PL). The erbium mixed
alkylated SiNCs shows an orange PL emission peak at around 595
nm that originates from radiative recombination of Si. Er/C11-SiNCs
mixture also exhibits a weak PL emission peak at 1536 nm that
originates from the intra-4f transition in erbium ions (Er3+). The PL
peak of Si in Er/C11-SiNCs mixture is increased in the intensity up to
three times as compared to pure C11-SiNCs. The collected data
suggest that this chemical mixing route leads instead to a transfer of
energy from erbium ions to alkylated SiNCs.
Abstract: Passing the entrance exam to a university is a major
step in one's life. University entrance exam commonly known as
Kankor is the nationwide entrance exam in Afghanistan. This
examination is prerequisite for all public and private higher education
institutions at undergraduate level. It is usually taken by students who
are graduated from high schools. In this paper, we reflect the major
educational school graduates issues and propose ICT-based test
preparation environment, known as ‘Online Kankor Exam Prep
System’ to give students the tools to help them pass the university
entrance exam on the first try. The system is based on Intelligent
Tutoring System (ITS), which introduced an essential package of
educational technology for learners that features: (I) exam-focused
questions and content; (ii) self-assessment environment; and (iii) test
preparation strategies in order to help students to acquire the necessary
skills in their carrier and keep them up-to-date with instruction.
Abstract: We have developed a new computer program in
Fortran 90, in order to obtain numerical solutions of a system
of Relativistic Magnetohydrodynamics partial differential equations
with predetermined gravitation (GRMHD), capable of simulating
the formation of relativistic jets from the accretion disk of matter
up to his ejection. Initially we carried out a study on numerical
methods of unidimensional Finite Volume, namely Lax-Friedrichs,
Lax-Wendroff, Nessyahu-Tadmor method and Godunov methods
dependent on Riemann problems, applied to equations Euler in
order to verify their main features and make comparisons among
those methods. It was then implemented the method of Finite
Volume Centered of Nessyahu-Tadmor, a numerical schemes that
has a formulation free and without dimensional separation of
Riemann problem solvers, even in two or more spatial dimensions,
at this point, already applied in equations GRMHD. Finally, the
Nessyahu-Tadmor method was possible to obtain stable numerical
solutions - without spurious oscillations or excessive dissipation -
from the magnetized accretion disk process in rotation with respect
to a central black hole (BH) Schwarzschild and immersed in a
magnetosphere, for the ejection of matter in the form of jet over a
distance of fourteen times the radius of the BH, a record in terms
of astrophysical simulation of this kind. Also in our simulations,
we managed to get substructures jets. A great advantage obtained
was that, with the our code, we got simulate GRMHD equations in
a simple personal computer.
Abstract: This paper presents optimization of makespan for ‘n’
jobs and ‘m’ machines flexible job shop scheduling problem with
sequence dependent setup time using genetic algorithm (GA)
approach. A restart scheme has also been applied to prevent the
premature convergence. Two case studies are taken into
consideration. Results are obtained by considering crossover
probability (pc = 0.85) and mutation probability (pm = 0.15). Five
simulation runs for each case study are taken and minimum value
among them is taken as optimal makespan. Results indicate that
optimal makespan can be achieved with more than one sequence of
jobs in a production order.
Abstract: Starting in 2020, an EU-wide CO2-limitation of
95 g/km is scheduled for the average of an OEMs passenger car fleet.
Taking that into consideration additional improvement measures of
the Diesel cycle are necessary in order to reduce fuel consumption
and emissions while boosting, or at the least, keeping performance
values at the same time.
The present article deals with the possibilities of an optimized
air/water charge air cooler, also called iCAC (indirect Charge Air
Cooler) for a Diesel passenger car amongst extreme-boundary
conditions. In this context, the precise objective was to show the
impact of improved intercooling with reference to the engine working
process (fuel consumption and NOx-emissions). Several extremeboundaries
- e.g. varying ambient temperatures or mountainous
routes - that will become very important in the near future regarding
RDE (Real Driving emissions) were subject of the investigation.
With the introduction of RDE in 2017 (EU6c measure), the
controversial NEDC (New European Driving Cycle) will belong to
the past and the OEMs will have to avoid harmful emissions in any
conceivable real life situation.
This is certainly going to lead to optimization-measurements at the
powertrain, which again is going to make the implementation of
iCACs, presently solely used for the premium class, more and more
attractive for compact class cars. The investigations showed a benefit
in FC between 1 and 3% for the iCAC in real world conditions.
Abstract: In this study which has been conducted in Akçasu
Forest Range District of Devrek Forest Directorate; 3 methods (weed
control with labourer power, cover removal with Hitachi F20
Excavator, and weed control with agricultural equipment mounted on
a Ferguson 240S agriculture tractor) were utilized in weed control
efforts in regeneration of degraded oriental beech forests have been
compared. In this respect, 3 methods have been compared by
determining certain work hours and standard durations of unit areas
(1 hectare). For this purpose, evaluating the tasks made with human
and machine force from the aspects of duration, productivity and
costs, it has been aimed to determine the most productive method in
accordance with the actual ecological conditions of research field.
Within the scope of the study, the time studies have been conducted
for 3 methods used in weed control efforts. While carrying out those
studies, the performed implementations have been evaluated by
dividing them into business stages. Also, the actual data have been
used while calculating the cost accounts. In those calculations, the
latest formulas and equations which are also used in developed
countries have been utilized. The variance of analysis (ANOVA) was
used in order to determine whether there is any statistically
significant difference among obtained results, and the Duncan test
was used for grouping if there is significant difference. According to
the measurements and findings carried out within the scope of this
study, it has been found during living cover removal efforts in
regeneration efforts in demolished oriental beech forests that the
removal of weed layer in 1 hectare of field has taken 920 hours with
labourer force, 15.1 hours with excavator and 60 hours with an
equipment mounted on a tractor. On the other hand, it has been
determined that the cost of removal of living cover in unit area (1
hectare) was 3220.00 TL for labourer power, 1250 TL for excavator
and 1825 TL for equipment mounted on a tractor.
According to the obtained results, it has been found that the
utilization of excavator in weed control effort in regeneration of
degraded oriental beech regions under actual ecological conditions of
research field has been found to be more productive from both of
aspects of duration and costs. These determinations carried out
should be repeated in weed control efforts in degraded forest fields
with different ecological conditions, it is compulsory for finding the
most efficient weed control method. These findings will light the way
of technical staff of forestry directorate in determination of the most
effective and economic weed control method. Thus, the more actual
data will be used while preparing the weed control budgets, and there
will be significant contributions to national economy. Also the results of this and similar studies are very important for developing the policies for our forestry in short and long term.
Abstract: In order to manufacture short gap single Si nanowire
(NW) field effect transistor (FET) by imprinting and transferring
method, we introduce the method using Al2O3 sacrificial layer. The
diameters of cylindrical Si NW addressed between Au electrodes by
dielectrophoretic (DEP) alignment method are controlled to 106, 128,
and 148 nm. After imprinting and transfer process, cylindrical Si NW
is embedded in PVP adhesive and dielectric layer. By curing
transferred cylindrical Si NW and Au electrodes on PVP-coated p++ Si
substrate with 200nm-thick SiO2, 3μm gap Si NW FET fabrication
was completed. As the diameter of embedded Si NW increases, the
mobility of FET increases from 80.51 to 121.24 cm2/V·s and the
threshold voltage moves from –7.17 to –2.44 V because the ratio of
surface to volume gets reduced.
Abstract: With a long history, dual-task has become one of the
most intriguing research fields regarding human brain functioning
and cognition. However, findings considering effects of taskinterrelations
are limited (especially, in combined motor and
cognitive tasks). Therefore, we aimed at developing a measurement
system in order to analyse interrelation effects of cognitive and motor
tasks. On the one hand, the present study demonstrates the
applicability of the measurement system and on the other hand first
results regarding a systematisation of different task combinations are
shown. Future investigations should combine imagine technologies
and this developed measurement system.
Abstract: TiO2 thin films have been prepared by the sol-gel dipcoating
technique in order to elaborate antireflective thin films for
monocrystalline silicon (mono-Si). The titanium isopropoxyde was
chosen as a precursor with hydrochloric acid as a catalyser for
preparing a stable solution. The optical properties have been tailored
with varying the solution concentration, the withdrawn speed, and the
heat-treatment. We showed that using a TiO2 single layer with 64.5
nm in thickness, heat-treated at 450°C or 300°C reduces the mono-Si
reflection at a level lower than 3% over the broadband spectral
domains [669-834] nm and [786-1006] nm respectively. Those latter
performances are similar to the ones obtained with double layers of
low and high refractive index glasses respectively.
Abstract: The exact theoretical expression describing the
probability distribution of nonlinear sea-surface elevations derived
from the second-order narrowband model has a cumbersome form
that requires numerical computations, not well-disposed to theoretical
or practical applications. Here, the same narrowband model is reexamined
to develop a simpler closed-form approximation suitable
for theoretical and practical applications. The salient features of the
approximate form are explored, and its relative validity is verified
with comparisons to other readily available approximations, and
oceanic data.
Abstract: The globalization of markets, the need to develop
competitive advantages and core competencies, among other things,
lead organizations to increasingly cross borders to operate in other
countries. The expatriation of professionals who go to work in
another country besides their own becomes increasingly common. In
order to generate data about this issue, research was conducted
concerning the perception of expatriate employees concerning
expatriation success. The research method used was case study
through a qualitative approach. This research was done through
interviews with five India expatriates and five China expatriates,
interview with expatriate department heads and analysis of company
documents. It was found that there are differences between the
organizational perception and perception of expatriates of what
constitutes mission success. The paper also provides suggestions for
further research and suggestions for future expatriates.
Abstract: The tomato is a very important crop, whose
cultivation in the Mediterranean basin is severely affected by the
phytoparasitic weed Phelipanche ramosa. The semiarid regions of
the world are considered the main areas where this parasitic weed is
established causing heavy infestation as it is able to produce high
numbers of seeds (up to 500,000 per plant), which remain viable for
extended period (more than 20 years). In this paper the results
obtained from eleven treatments in order to control this parasitic
weed including chemical, agronomic, biological and biotechnological
methods compared with the untreated test under two plowing depths
(30 and 50 cm) are reported. The split-plot design with 3 replicates
was adopted. In 2014 a trial was performed in Foggia province
(southern Italy) on processing tomato (cv Docet) grown in the field
infested by Phelipanche ramosa. Tomato seedlings were transplant
on May 5, on a clay-loam soil. During the growing cycle of the
tomato crop, at 56-78 and 92 days after transplantation, the number
of parasitic shoots emerged in each plot was detected. At tomato
harvesting, on August 18, the major quantity-quality yield parameters
were determined (marketable yield, mean weight, dry matter, pH,
soluble solids and color of fruits). All data were subjected to analysis
of variance (ANOVA) and the means were compared by Tukey's test.
Each treatment studied did not provide complete control against
Phelipanche ramosa. However, among the different methods tested,
some of them which Fusarium, gliphosate, radicon biostimulant and
Red Setter tomato cv (improved genotypes obtained by Tilling
technology) under deeper plowing (50 cm depth) proved to mitigate
the virulence of the Phelipanche ramose attacks. It is assumed that
these effects can be improved combining some of these treatments
each other, especially for a gradual and continuing reduction of the
“seed bank” of the parasite in the soil.
Abstract: Logistics distributors face the issue of having to
provide increasing service levels while being forced to reduce costs at
the same time. Same-day delivery, quick order processing and rapidly
growing ranges of articles are only some of the prevailing challenges.
One key aspect of the performance of an intra-logistics system is how
often and in which amplitude congestions and dysfunctions affect the
processing operations. By gaining knowledge of the so called
‘performance availability’ of such a system during the planning stage,
oversizing and wasting can be reduced whereas planning
transparency is increased. State of the art for the determination of this
KPI is simulation studies. However, their structure and therefore their
results may vary unforeseeably. This article proposes a concept for
the establishment of ‘certified’ and hence reliable and comparable
simulation models.
Abstract: The paper involves a chain of activities from
synthesis, establishment of the methodology for characterization and
testing of novel protective materials through the pilot production and
application on model supports.
It summarizes the results regarding the development of the pilot
production protocol for newly developed self-cleaning materials. The
optimization of the production parameters was completed in order to
improve the most important functional properties (mineralogy
characteristics, particle size, self-cleaning properties and
photocatalytic activity) of the newly designed nanocomposite
material.
Abstract: Near infrared (NIR) spectroscopy has always been of
great interest in the food and agriculture industries. The development
of prediction models has facilitated the estimation process in recent
years. In this study, 110 crude palm oil (CPO) samples were used to
build a free fatty acid (FFA) prediction model. 60% of the collected
data were used for training purposes and the remaining 40% used for
testing. The visible peaks on the NIR spectrum were at 1725 nm and
1760 nm, indicating the existence of the first overtone of C-H bands.
Principal component regression (PCR) was applied to the data in
order to build this mathematical prediction model. The optimal
number of principal components was 10. The results showed
R2=0.7147 for the training set and R2=0.6404 for the testing set.
Abstract: Safety is one of the most important considerations
when buying a new car. While active safety aims at avoiding
accidents, passive safety systems such as airbags and seat belts
protect the occupant in case of an accident. In addition to legal
regulations, organizations like Euro NCAP provide consumers with
an independent assessment of the safety performance of cars and
drive the development of safety systems in automobile industry.
Those ratings are mainly based on injury assessment reference values
derived from physical parameters measured in dummies during a car
crash test.
The components and sub-systems of a safety system are designed
to achieve the required restraint performance. Sled tests and other
types of tests are then carried out by car makers and their suppliers
to confirm the protection level of the safety system. A Knowledge
Discovery in Databases (KDD) process is proposed in order to
minimize the number of tests. The KDD process is based on the
data emerging from sled tests according to Euro NCAP specifications.
About 30 parameters of the passive safety systems from different data
sources (crash data, dummy protocol) are first analysed together with
experts opinions. A procedure is proposed to manage missing data
and validated on real data sets. Finally, a procedure is developed to
estimate a set of rough initial parameters of the passive system before
testing aiming at reducing the number of tests.