Abstract: Multirate multimedia delivery applications in multihop Wireless Mesh Network (WMN) are data redundant and delay-sensitive, which brings a lot of challenges for designing efficient transmission systems. In this paper, we propose a new cross layer resource allocation scheme to minimize the receiver side distortion within the delay bound requirements, by exploring application layer Position and Value (P-V) diversity as well as the multihop Effective Capacity (EC). We specifically consider image transmission optimization here. First of all, the maximum supportable source traffic rate is identified by exploring the multihop Effective Capacity (EC) model. Furthermore, the optimal source coding rate is selected according to the P-V diversity of multirate media streaming, which significantly increases the decoded media quality. Simulation results show the proposed approach improved media quality significantly compared with traditional approaches under the same QoS requirements.
Abstract: This paper presents the modeling and simulation of a hybrid proton exchange membrane fuel cell (PEMFC) with an energy storage system for use in a stand-alone distributed generation (DG) system. The simulation model consists of fuel cell DG, lead-acid battery, maximum power point tracking and power conditioning unit which is modeled in the MATLAB/Simulink platform. Poor loadfollowing characteristics and slow response to rapid load changes are some of the weaknesses of PEMFC because of the gas processing reaction and the fuel cell dynamics. To address the load-tracking issues in PEMFC, a hybrid PEMFC and battery storage system is considered and modelled. The model utilizes PEMFC as the main energy source whereas the battery functions as energy storage to compensate for the limitations of PEMFC.Simulation results are given to show the overall system performance under light and heavyloading conditions.
Abstract: Bubble columns have a variety of applications in
absorption, bio-reactions, catalytic slurry reactions, and coal
liquefaction; because they are simple to operate, provide good heat
and mass transfer, having less operational cost. The use of
Computational Fluid Dynamics (CFD) for bubble column becomes
important, since it can describe the fluid hydrodynamics on both local
and global scale. Euler- Euler two-phase fluid model has been used to
simulate two-phase (air and water) transient up-flow in bubble
column (15cm diameter) using FLUENT6.3. These simulations and
experiments were operated over a range of superficial gas velocities
in the bubbly flow and churn turbulent regime (1 to16 cm/s) at
ambient conditions. Liquid velocity was varied from 0 to 16cm/s. The
turbulence in the liquid phase is described using the standard k-ε
model. The interactions between the two phases are described
through drag coefficient formulations (Schiller Neumann). The
objectives are to validate CFD simulations with experimental data,
and to obtain grid-independent numerical solutions. Quantitatively
good agreements are obtained between experimental data for hold-up
and simulation values. Axial liquid velocity profiles and gas holdup
profiles were also obtained for the simulation.
Abstract: Although lighting systems powered by Photovoltaic
(PV) cells have existed for many years, they are not widely used,
especially in lighting for buildings, due to their high initial cost and
low conversion efficiency. One of the technical challenges facing PV
powered lighting systems has been how to use dc power generated by
the PV module to energize common light sources that are designed to
operate efficiently under ac power. Usually, the efficiency of the dc
light sources is very poor compared to ac light sources. Rapid
developments in LED lighting systems have made this technology a
potential candidate for PV powered lighting systems. This study
analyzed the efficiency of each component of PV powered lighting
systems to identify optimum system configurations for different
applications.
Abstract: In this paper back-propagation artificial neural
network (BPANN) is employed to predict the limiting drawing ratio
(LDR) of the deep drawing process. To prepare a training set for
BPANN, some finite element simulations were carried out. die and
punch radius, die arc radius, friction coefficient, thickness, yield
strength of sheet and strain hardening exponent were used as the
input data and the LDR as the specified output used in the training of
neural network. As a result of the specified parameters, the program
will be able to estimate the LDR for any new given condition.
Comparing FEM and BPANN results, an acceptable correlation was
found.
Abstract: This paper describes about dynamic reconfiguration to
miniaturize arithmetic circuits in general-purpose processor. Dynamic
reconfiguration is a technique to realize required functions by
changing hardware construction during operation. The proposed
arithmetic circuit performs floating-point arithmetic which is
frequently used in science and technology. The data format is
floating-point based on IEEE754. The proposed circuit is designed
using VHDL, and verified the correct operation by simulations and
experiments.
Abstract: Cross layer optimization based on utility functions has
been recently studied extensively, meanwhile, numerous types of
utility functions have been examined in the corresponding literature.
However, a major drawback is that most utility functions take a fixed
mathematical form or are based on simple combining, which can
not fully exploit available information. In this paper, we formulate a
framework of cross layer optimization based on Adaptively Weighted
Utility Functions (AWUF) for fairness balancing in OFDMA networks.
Under this framework, a two-step allocation algorithm is
provided as a sub-optimal solution, whose control parameters can be
updated in real-time to accommodate instantaneous QoS constrains.
The simulation results show that the proposed algorithm achieves
high throughput while balancing the fairness among multiple users.
Abstract: loss of feedwater accident is one of the frequently sever accidents in steam boiler facilities. It threatens the system structural integrity and generates serious hazards and economic loses. The safety analysis of the thermal installations, based extensively on the numeric simulation. The simulation analysis using realistic computer codes like Relap5/Mod3.2 will help understand steam boiler thermal-hydraulic behavior during normal and abnormal conditions. In this study, we are interested on the evaluation of the radiant steam boiler assessment and response to loss-of-feedwater accident. Pressure, temperature and flow rate profiles are presented in various steam boiler system components. The obtained results demonstrate the importance and capability of the Relap5/Mod3.2 code in the thermal-hydraulic analysis of the steam boiler facilities.
Abstract: This paper describes a newly designed decentralized
nonlinear control strategy to control a robot manipulator. Based on the
concept of the nonlinear state feedback theory and decentralized
concept is developed to improve the drawbacks in previous works
concerned with complicate intelligent control and low cost effective
sensor. The control methodology is derived in the sense of Lyapunov
theorem so that the stability of the control system is guaranteed. The
decentralized algorithm does not require other joint angle and velocity
information. Individual Joint controller is implemented using a digital
processor with nearly actuator to make it possible to achieve good
dynamics and modular. Computer simulation result has been
conducted to validate the effectiveness of the proposed control scheme
under the occurrence of possible uncertainties and different reference
trajectories. The merit of the proposed control system is indicated in
comparison with a classical control system.
Abstract: The Reverse Monte Carlo (RMC) simulation is applied in the study of an aqueous electrolyte LiCl6H2O. On the basis of the available experimental neutron scattering data, RMC computes pair radial distribution functions in order to explore the structural features of the system. The obtained results include some unrealistic features. To overcome this problem, we use the Hybrid Reverse Monte Carlo (HRMC), incorporating an energy constraint in addition to the commonly used constraints derived from experimental data. Our results show a good agreement between experimental and computed partial distribution functions (PDFs) as well as a significant improvement in pair partial distribution curves. This kind of study can be considered as a useful test for a defined interaction model for conventional simulation techniques.
Abstract: This paper presents a model for an unreliable
production line, which is operated according to demand with constant
work-in-process (CONWIP). A simulation model is developed based
on the discrete model and several case problems are analyzed using
the model. The model is utilized to optimize storage space capacities
at intermediate stages and the number of kanbans at the last stage,
which is used to trigger the production at the first stage. Furthermore,
effects of several line parameters on production rate are analyzed
using design of experiments.
Abstract: In this study, the hydrogen transport phenomenon was
numerically evaluated by using hydrogen-enhanced localized
plasticity (HELP) mechanisms. Two dominant governing equations,
namely, the hydrogen transport model and the elasto-plastic model,
were introduced. In addition, the implicitly formulated equations of
the governing equations were implemented into ABAQUS UMAT
user-defined subroutines. The simulation results were compared to
published results to validate the proposed method.
Abstract: Nowadays in applications of renewable energy sources
it is important to develop powerful and energy-saving photovoltaic
converters and to keep the prescriptions of the standards. In grid
connected PV converters the obvious solution to increase the
efficiency is to reduce the switching losses. Our new developed
control method reduces the switching losses and keeps the limitations
of the harmonic distortion standards. The base idea of the method is
the utilization of 3-state control causing discontinuous current mode
at low input power. In the following sections the control theory, the
realizations and the simulation results are presented.
Abstract: In this paper we present our results on the performance analysis of a multi-product manufacturing line. We study the influence of external perturbations, intermediate buffer content and the number of manufacturing stages on the production tracking error of each machine in the multi-product line operated under a surplusbased production control policy. Starting by the analysis of a single machine with multiple production stages (one for each product type), we provide bounds on the production error of each stage. Then, we extend our analysis to a line of multi-stage machines, where similarly, bounds on each production tracking error for each product type, as well as buffer content are obtained. Details on performance of the closed-loop flow line model are illustrated in numerical simulations.
Abstract: This paper presents a new and efficient approach for
capacitor placement in radial distribution systems that determine
the optimal locations and size of capacitor with an objective of
improving the voltage profile and reduction of power loss. The
solution methodology has two parts: in part one the loss sensitivity
factors are used to select the candidate locations for the capacitor
placement and in part two a new algorithm that employs Plant growth
Simulation Algorithm (PGSA) is used to estimate the optimal size
of capacitors at the optimal buses determined in part one. The main
advantage of the proposed method is that it does not require any
external control parameters. The other advantage is that it handles the
objective function and the constraints separately, avoiding the trouble
to determine the barrier factors. The proposed method is applied to 9
and 34 bus radial distribution systems. The solutions obtained by the
proposed method are compared with other methods. The proposed
method has outperformed the other methods in terms of the quality
of solution.
Abstract: Doubly fed induction machines DFIM are used
mainly for wind energy conversion in MW power plants. This paper
presents a new strategy of field oriented control ,it is based on the
principle of a double flux orientation of stator and rotor at the same
time. Therefore, the orthogonality created between the two oriented
fluxes, which must be strictly observed, leads to generate a linear and
decoupled control with an optimal torque. The obtained simulation
results show the feasibility and the effectiveness of the suggested
method.
Abstract: Restoration of endodontically treated teeth is a
common problem in dentistry, related to the fractures occurring in
such teeth and to concentration of forces little information regarding
variation of basic preparation guidelines in stress distribution has
been available. To date, there is still no agreement in the literature
about which material or technique can optimally restore
endodontically treated teeth. The aim of the present study was to
evaluate the influence of the core height and restoration materials on
corono-radicular restored upper first premolar. The first step of the
study was to achieve 3D models in order to analyze teeth, dowel and
core restorations and overlying full ceramic crowns. The FEM model
was obtained by importing the solid model into ANSYS finite
element analysis software. An occlusal load of 100 N was conducted,
and stresses occurring in the restorations, and teeth structures were
calculated. Numerical simulations provide a biomechanical
explanation for stress distribution in prosthetic restored teeth. Within
the limitations of the present study, it was found that the core height
has no important influence on the stress generated in coronoradicular
restored premolars. It can be drawn that the cervical regions
of the teeth and restorations were subjected to the highest stress
concentrations.
Abstract: This paper discusses a systematic design of a Σ-Δ fractional-N Phase-Locked Loop based on HDL behavioral modeling. The proposed design consists in describing the mixed behavior of this PLL architecture starting from the specifications of each building block. The HDL models of critical PLL blocks have been described in VHDL-AMS to predict the different specifications of the PLL. The effect of different noise sources has been efficiently introduced to study the PLL system performances. The obtained results are compared with transistor-level simulations to validate the effectiveness of the proposed models for wireless applications in the frequency range around 2.45 GHz.
Abstract: In this paper, the estimation of the stress-strength
parameter R = P(Y < X), when X and Y are independent and both
are Lomax distributions with the common scale parameters but
different shape parameters is studied. The maximum likelihood
estimator of R is derived. Assuming that the common scale parameter
is known, the bayes estimator and exact confidence interval of R are
discussed. Simulation study to investigate performance of the
different proposed methods has been carried out.
Abstract: This paper describes a simulation model for analyzing artificial emotion injected to design the game characters. Most of the game storyboard is interactive in nature and the virtual characters of the game are equipped with an individual personality and dynamic emotion value which is similar to real life emotion and behavior. The uncertainty in real expression, mood and behavior is also exhibited in game paradigm and this is focused in the present paper through a fuzzy logic based agent and storyboard. Subsequently, a pheromone distribution or labeling is presented mimicking the behavior of social insects.