Abstract: Self-compacting concrete (SCC) developed in Japan
in the late 80s has enabled the construction industry to reduce
demand on the resources, improve the work condition and also
reduce the impact of environment by elimination of the need for
compaction. Fuzzy logic (FL) approaches has recently been used to
model some of the human activities in many areas of civil
engineering applications. Especially from these systems in the model
experimental studies, very good results have been obtained. In the
present study, a model for predicting compressive strength of SCC
containing various proportions of fly ash, as partial replacement of
cement has been developed by using Fuzzy Inference System (FIS).
For the purpose of building this model, a database of experimental
data were gathered from the literature and used for training and
testing the model. The used data as the inputs of fuzzy logic models
are arranged in a format of five parameters that cover the total binder
content, fly ash replacement percentage, water content,
superplasticizer and age of specimens. The training and testing results
in the fuzzy logic model have shown a strong potential for predicting
the compressive strength of SCC containing fly ash in the considered
range.
Abstract: Machining parameters are very important in
determining the surface quality of any material. In the past decade,
some new engineering materials were developed for the
manufacturing industry which created a need to conduct an
investigation on the impact of the said parameters on their surface
roughness. Polyurethane (PU) block is widely used in the automotive
industry to manufacture parts such as checking fixtures that are used
to verify the dimensional accuracy of automotive parts. In this paper,
the design of experiment (DOE) was used to investigate on the effect
of the milling parameters on the PU block. Furthermore, an analysis
of the machined surface chemical composition was done using
scanning electron microscope (SEM). It was found that the surface
roughness of the PU block is severely affected when PU undergoes a
flood machining process instead of a dry condition. In addition the
stepover and the silicon content were found to be the most significant
parameters that influence the surface quality of the PU block.
Abstract: Safety is one of the most important considerations
when buying a new car. While active safety aims at avoiding
accidents, passive safety systems such as airbags and seat belts
protect the occupant in case of an accident. In addition to legal
regulations, organizations like Euro NCAP provide consumers with
an independent assessment of the safety performance of cars and
drive the development of safety systems in automobile industry.
Those ratings are mainly based on injury assessment reference values
derived from physical parameters measured in dummies during a car
crash test.
The components and sub-systems of a safety system are designed
to achieve the required restraint performance. Sled tests and other
types of tests are then carried out by car makers and their suppliers
to confirm the protection level of the safety system. A Knowledge
Discovery in Databases (KDD) process is proposed in order to
minimize the number of tests. The KDD process is based on the
data emerging from sled tests according to Euro NCAP specifications.
About 30 parameters of the passive safety systems from different data
sources (crash data, dummy protocol) are first analysed together with
experts opinions. A procedure is proposed to manage missing data
and validated on real data sets. Finally, a procedure is developed to
estimate a set of rough initial parameters of the passive system before
testing aiming at reducing the number of tests.
Abstract: Metal matrix composites (MMCs) attract considerable
attention as a result from its ability in providing a high strength, high
modulus, high toughness, high impact properties, improving wear
resistance and providing good corrosion resistance compared to
unreinforced alloy. Aluminium Silicon (Al/Si) alloy MMC has been
widely used in various industrial sectors such as in transportation,
domestic equipment, aerospace, military, construction, etc.
Aluminium silicon alloy is an MMC that had been reinforced with
aluminium nitrate (AlN) particle and become a new generation
material use in automotive and aerospace sector. The AlN is one of
the advance material that have a bright prospect in future since it has
features such as lightweight, high strength, high hardness and
stiffness quality. However, the high degree of ceramic particle
reinforcement and the irregular nature of the particles along the
matrix material that contribute to its low density is the main problem
which leads to difficulties in machining process. This paper examined
the tool wear when milling AlSi/AlN Metal Matrix Composite using
a TiB2 (Titanium diboride) coated carbide cutting tool. The volume
of the AlN reinforced particle was 10% and milling process was
carried out under dry cutting condition. The TiB2 coated carbide
insert parameters used were at the cutting speed of (230, 300 and
370m/min, feed rate of 0.8, Depth of Cut (DoC) at 0.4m). The
Sometech SV-35 video microscope system used to quantify of the
tool wear. The result shown that tool life span increasing with the
cutting speeds at (370m/min, feed rate of 0.8mm/tooth and DoC at
0.4mm) which constituted an optimum condition for longer tool life
lasted until 123.2 mins. Meanwhile, at medium cutting speed which
at 300m/m, feed rate of 0.8mm/tooth and depth of cut at 0.4mm we
found that tool life span lasted until 119.86 mins while at low cutting
speed it lasted in 119.66 mins. High cutting speed will give the best
parameter in cutting AlSi/AlN MMCs material. The result will help
manufacturers in machining process of AlSi/AlN MMCs materials.
Abstract: We present an analytical model for the calculation of
the sensitivity, the spectral current noise and the detective parameter
for an optically illuminated In0.53Ga0.47As n+nn+ diode. The
photocurrent due to the excess carrier is obtained by solving the
continuity equation. Moreover, the current noise level is evaluated at
room temperature and under a constant voltage applied between the
diode terminals. The analytical calculation of the current noise in the
n+nn+ structure is developed by considering the free carries
fluctuations. The responsivity and the detection parameter are
discussed as functions of the doping concentrations and the emitter
layer thickness in one-dimensional homogeneous n+nn+ structure.
Abstract: Exact solution of an unsteady flow of elastico-viscous
electrically conducting fluid through a porous media in a tube of
elliptical cross section under the influence of constant pressure
gradient and magnetic field has been obtained in this paper. Initially,
the flow is generated by a constant pressure gradient. After attaining
the steady state, the pressure gradient is suddenly withdrawn and the
resulting fluid motion in a tube of elliptical cross section by taking
into account of the transverse magnetic field and porosity factor of
the bounding surface is investigated. The problem is solved in twostages
the first stage is a steady motion in tube under the influence of
a constant pressure gradient, the second stage concern with an
unsteady motion. The problem is solved employing separation of
variables technique. The results are expressed in terms of a nondimensional
porosity parameter (K), magnetic parameter (m) and
elastico-viscosity parameter (β), which depends on the Non-
Newtonian coefficient. The flow parameters are found to be identical
with that of Newtonian case as elastic-viscosity parameter and
magnetic parameter tends to zero and porosity tends to infinity. It is
seen that the effect of elastico-viscosity parameter, magnetic
parameter and the porosity parameter of the bounding surface has
significant effect on the velocity parameter.
Abstract: In this paper, the dynamic characteristics of a threelobe
journal bearing lubricated with micropolar fluids are determined
by the linear stability theory. Lubricating oil containing additives and
contaminants is modelled as micropolar fluid. The modified
Reynolds equation is obtained using the micropolar lubrication theory
.The finite difference technique has been used to determine the
solution of the modified Reynolds equation. The dynamic
characteristics in terms of stiffness, damping coefficients, the critical
mass and whirl ratio are determined for various values of size of
material characteristic length and the coupling number. The
computed results show that the three-lobe bearing lubricated with
micropolar fluid exhibits better stability compared with that
lubricated with Newtonian fluid. According to the results obtained,
the effect of the parameter micropolar fluid is remarkable on the
dynamic characteristics and stability of the three-lobe bearing.
Abstract: Many of the ever-growing elderly population require
exercise, such as running, for health management. One important
element of a runner’s training is the choice of shoes for exercise; shoes
are important because they provide the interface between the feet and
road. When we purchase shoes, we may instinctively choose a pair
after trying on many different pairs of shoes. Selecting the shoes
instinctively may work, but it does not guarantee a suitable fit for
running activities. Therefore, if we could select suitable shoes for each
runner from the viewpoint of brain activities, it would be helpful for
validating shoe selection. In this paper, we describe how brain
activities show different characteristics during particular task,
corresponding to different properties of shoes. Using five subjects, we
performed a verification experiment, applying weight, softness, and
flexibility as shoe properties. In order to affect the shoe property’s
differences to the brain, subjects run for 10 min. Before and after
running, subjects conducted a paced auditory serial addition task
(PASAT) as the particular task; and the subjects’ brain activities
during the PASAT are evaluated based on oxyhemoglobin and
deoxyhemoglobin relative concentration changes, measured by
near-infrared spectroscopy (NIRS). When the brain works actively,
oxihemoglobin and deoxyhemoglobin concentration drastically
changes; therefore, we calculate the maximum values of concentration
changes. In order to normalize relative concentration changes after
running, the maximum value are divided by before running maximum
value as evaluation parameters. The classification of the groups of
shoes is expressed on a self-organizing map (SOM). As a result,
deoxyhemoglobin can make clusters for two of the three types of
shoes.
Abstract: Monocopter is a single-wing rotary flying vehicle
which has the capability of hovering. This flying vehicle includes two
dynamic parts in which more efficiency can be expected rather than
other Micro UAVs due to the extended area of wing compared to its
fuselage. Low cost and simple mechanism in comparison to other
vehicles such as helicopter are the most important specifications of
this flying vehicle.
In the previous paper we discussed the introduction of the final
system but in this paper, the experimental design process of
Monocopter and its control algorithm has been investigated in
general. Also the editorial bugs in the previous article have been
corrected and some translational ambiguities have been resolved.
Initially by constructing several prototypes and carrying out many
flight tests the main design parameters of this air vehicle were
obtained by experimental measurements. Eventually the required
main monocopter for this project was constructed. After construction
of the monocopter in order to design, implementation and testing of
control algorithms first a simple optic system used for determining
the heading angle. After doing numerous tests on Test Stand, the
control algorithm designed and timing of applying control inputs
adjusted. Then other control parameters of system were tuned in
flight tests. Eventually the final control system designed and
implemented using the AHRS sensor and the final operational tests
performed successfully.
Abstract: Aerated concrete is a load bearing construction
material, which has high heat insulation parameters. Walls can be
erected from aerated concrete masonry constructions and in perfect
circumstances additional heat insulation is not required. The most
common problem in aerated concrete heat insulation properties is the
humidity distribution throughout the cross section of the masonry
elements as well as proper and conducted drying process of the
aerated concrete construction because only dry aerated concrete
masonry constructions can reach high heat insulation parameters.
In order to monitor drying process of the masonry and detect
humidity distribution throughout the cross section of aerated concrete
masonry construction application of electrical impedance
spectrometry is applied. Further test results and methodology of this
non-destructive testing method is described in this paper.
Abstract: We report on the use of strong external optical
feedback to enhance the modulation response of semiconductor lasers
over a frequency passband around modulation frequencies higher
than 60 GHz. We show that this modulation enhancement is a type of
photon-photon resonance (PPR) of oscillating modes in the external
cavity formed between the laser and the external reflector. The study
is based on a time-delay rate equation model that takes into account
both the strong feedback and multiple reflections in the external
cavity. We examine the harmonic and intermodulation distortions
associated with single and two-tone modulations in the mm-wave
band of the resonant modulation. We show that compared with
solitary lasers modulated around the carrier-photon resonance
frequency, the present mm-wave modulated signal has lower
distortions.
Abstract: Today’s modern interconnected power system is
highly complex in nature. In this, one of the most important
requirements during the operation of the electric power system is the
reliability and security. Power and frequency oscillation damping
mechanism improve the reliability. Because of power system
stabilizer (PSS) low speed response against of major fault such as
three phase short circuit, FACTs devise that can control the network
condition in very fast time, are becoming popular. But FACTs
capability can be seen in a major fault present when nonlinear models
of FACTs devise and power system equipment are applied. To realize
this aim, the model of multi-machine power system with FACTs
controller is developed in MATLAB/SIMULINK using Sim Power
System (SPS) blockiest. Among the FACTs device, Static
synchronous series compensator (SSSC) due to high speed changes
its reactance characteristic inductive to capacitive, is effective power
flow controller. Tuning process of controller parameter can be
performed using different method. But Genetic Algorithm (GA)
ability tends to use it in controller parameter tuning process. In this
paper firstly POD controller is used to power oscillation damping.
But in this station, frequency oscillation dos not has proper damping
situation. So FOD controller that is tuned using GA is using that
cause to damp out frequency oscillation properly and power
oscillation damping has suitable situation.
Abstract: This paper proposes a new technique to design a
fixed-structure robust loop shaping controller for the pneumatic
servosystem. In this paper, a new method based on a particle swarm
optimization (PSO) algorithm for tuning the weighting function
parameters to design an H∞ controller is presented. The PSO
algorithm is used to minimize the infinity norm of the transfer
function of the nominal closed loop system to obtain the optimal
parameters of the weighting functions. The optimal stability margin is
used as an objective in PSO for selecting the optimal weighting
parameters; it is shown that the proposed method can simplify the
design procedure of H∞ control to obtain optimal robust controller for
pneumatic servosystem. In addition, the order of the proposed
controller is much lower than that of the conventional robust loop
shaping controller, making it easy to implement in practical works.
Also two-degree-of-freedom (2DOF) control design procedure is
proposed to improve tracking performance in the face of noise and
disturbance. Result of simulations demonstrates the advantages of the
proposed controller in terms of simple structure and robustness
against plant perturbations and disturbances.
Abstract: E-business technologies, whereby business
transactions are conducted remotely using the Internet, present
unique opportunities and challenges for business. E-business
technologies are applicable to a wide range of organizations and
small and medium-sized enterprises (SMEs) are no exception. There
is an established body of literature about e-business, looking at
definitions, concepts, benefits and challenges. In general, however,
the research focus has been on larger organizations, not SMEs. In an
attempt to redress the balance of research, this paper looks at ebusiness
technologies specifically from a small business perspective.
It seeks to identify the possible barriers that SMEs might face when
considering adoption of the e-business concept and practice as part of
their business process change initiatives and implementation. To
facilitate analysis of these barriers a conceptual framework has been
developed which outlines the key conceptual and practical challenges
of e-business implementation in SMEs. This is developed following a
literature survey comprised of three categories: characteristics of
SMEs, issues of IS/IT use in SMEs and general e-business adoption
and implementation issues. The framework is then empirically
assessed against 7 SMEs who have yet to implement e-business or
whose e-business efforts have been unsatisfactory. Conclusions from
the case studies can be used to verify the framework, and set
parameters for further larger scale empirical investigation.
Abstract: A key issue in seismic risk analysis within the context
of Performance-Based Earthquake Engineering is the evaluation of
the expected seismic damage of structures under a specific
earthquake ground motion. The assessment of the seismic
performance strongly depends on the choice of the seismic Intensity
Measure (IM), which quantifies the characteristics of a ground
motion that are important to the nonlinear structural response. Several
conventional IMs of ground motion have been used to estimate their
damage potential to structures. Yet, none of them has been proved to
be able to predict adequately the seismic damage. Therefore,
alternative, scalar intensity measures, which take into account not
only ground motion characteristics but also structural information
have been proposed. Some of these IMs are based on integration of
spectral values over a range of periods, in an attempt to account for
the information that the shape of the acceleration, velocity or
displacement spectrum provides. The adequacy of a number of these
IMs in predicting the structural damage of 3D R/C buildings is
investigated in the present paper. The investigated IMs, some of
which are structure specific and some are non structure-specific, are
defined via integration of spectral values. To achieve this purpose
three symmetric in plan R/C buildings are studied. The buildings are
subjected to 59 bidirectional earthquake ground motions. The two
horizontal accelerograms of each ground motion are applied along
the structural axes. The response is determined by nonlinear time
history analysis. The structural damage is expressed in terms of the
maximum interstory drift as well as the overall structural damage
index. The values of the aforementioned seismic damage measures
are correlated with seven scalar ground motion IMs. The comparative
assessment of the results revealed that the structure-specific IMs
present higher correlation with the seismic damage of the three
buildings. However, the adequacy of the IMs for estimation of the
structural damage depends on the response parameter adopted.
Furthermore, it was confirmed that the widely used spectral
acceleration at the fundamental period of the structure is a good
indicator of the expected earthquake damage level.
Abstract: The present study was conducted to evaluate the
potential applicability of biological trickling filter system for the
treatment of simulated textile wastewater containing reactive azo
dyes with bacterial consortium under non-sterile conditions. The
percentage decolorization for the treatment of wastewater containing
structurally different dyes was found to be higher than 95% in all
trials. The stable bacterial count of the biofilm on stone media of the
trickling filter during the treatment confirmed the presence,
proliferation, dominance and involvement of the added microbial
consortium in the treatment of textile wastewater. Results of
physicochemical parameters revealed the reduction in chemical
oxygen demand (58.5-75.1%), sulphates (18.9-36.5%), and
phosphates (63.6-73.0%). UV-Visible and FTIR spectroscopy
confirmed decolorization of dye containing wastewater was ultimate
consequence of biodegradation. Toxicological studies revealed the
nontoxic nature of degradative metabolites.
Abstract: Tumor is an uncontrolled growth of tissues in any part
of the body. Tumors are of different types and they have different
characteristics and treatments. Brain tumor is inherently serious and
life-threatening because of its character in the limited space of the
intracranial cavity (space formed inside the skull). Locating the tumor
within MR (magnetic resonance) image of brain is integral part of the
treatment of brain tumor. This segmentation task requires
classification of each voxel as either tumor or non-tumor, based on
the description of the voxel under consideration. Many studies are
going on in the medical field using Markov Random Fields (MRF) in
segmentation of MR images. Even though the segmentation process
is better, computing the probability and estimation of parameters is
difficult. In order to overcome the aforementioned issues, Conditional
Random Field (CRF) is used in this paper for segmentation, along
with the modified artificial bee colony optimization and modified
fuzzy possibility c-means (MFPCM) algorithm. This work is mainly
focused to reduce the computational complexities, which are found in
existing methods and aimed at getting higher accuracy. The
efficiency of this work is evaluated using the parameters such as
region non-uniformity, correlation and computation time. The
experimental results are compared with the existing methods such as
MRF with improved Genetic Algorithm (GA) and MRF-Artificial
Bee Colony (MRF-ABC) algorithm.
Abstract: In oases, the surface water resources are becoming
increasingly scarce and groundwater resources, which generally have
a poor quality due to the high levels of salinity, are often
overexploited. Water saving have therefore become imperative for
better oases sustainability. If drip irrigation is currently recommended
in Morocco for saving water and valuing, its use in the sub-desert
areas does not keep water safe from high evaporation rates. An
alternative to this system would be the use of subsurface drip
irrigation. This technique is defined as an application of water under
the soil surface through drippers, which deliver water at rates
generally similar to surface drip irrigation. As subsurface drip
irrigation is a recently introduced in Morocco, a better understanding
of the infiltration process around a buried source, in local conditions,
and its impact on plant growth is necessarily required. This study
aims to contribute to improving the water use efficiency by testing
the performance of subsurface irrigation system, especially in areas
where water is a limited source. The objectives of this research are
performance evaluation in arid conditions of the subsurface drip
irrigation system for young date palms compared to the surface drip.
In this context, an experimental test is installed at a farmer’s field in
the area of Erfoud (Errachidia Province, southeastern Morocco),
using the subsurface drip irrigation system in comparison with the
classic drip system for young date palms. Flow measurement to
calculate the uniformity of the application of water was done through
two methods: a flow measurement of drippers above the surface and
another one underground. The latter method has also helped us to
estimate losses through evaporation for both irrigation techniques. In
order to compare the effect of two irrigation modes, plants were
identified for each type of irrigation to monitor certain agronomic
parameters (cumulative numbers of palms and roots development).
Experimentation referred to a distribution uniformity of about 88%;
considered acceptable for subsurface drip irrigation while it is around
80% for the surface drip irrigation. The results also show an increase
in root development and in the number of palm, as well as a
substantial water savings due to lower evaporation losses compared
to the classic drip irrigation.
The results of this study showed that subsurface drip irrigation is
an efficient technique, which allows sustainable irrigation in arid
areas.
Abstract: This article is deal with the experimental
investigations of the laser diode matrixes (LDM) based on the
AlGaAs/GaAs heterostructures (lasing wavelength 790-880 nm) to
find optimal LDM parameters for active vision systems. In particular,
the dependence of LDM radiation pulse power on the pulse duration
and LDA active layer heating as well as the LDM radiation
divergence are discussed.
Abstract: In this paper an isolated wind-diesel hybrid power
system has been considered for reactive power control study having
an induction generator for wind power conversion and synchronous
alternator with automatic voltage regulator (AVR) for diesel unit is
presented. The dynamic voltage stability evaluation is dependent on
small signal analysis considering a Static VAR Compensator (SVC)
and IEEE type -I excitation system. It's shown that the variable
reactive power source like SVC is crucial to meet the varying
demand of reactive power by induction generator and load and to
acquire an excellent voltage regulation of the system with minimum
fluctuations. Integral square error (ISE) criterion can be used to
evaluate the optimum setting of gain parameters. Finally the dynamic
responses of the power systems considered with optimum gain setting
will also be presented.