Abstract: This paper deals with the problem of automatic rule
generation for fuzzy systems design. The proposed approach is based
on hybrid artificial bee colony (ABC) optimization and weighted least
squares (LS) method and aims to find the structure and parameters of
fuzzy systems simultaneously. More precisely, two ABC based fuzzy
modeling strategies are presented and compared. The first strategy
uses global optimization to learn fuzzy models, the second one
hybridizes ABC and weighted least squares estimate method. The
performances of the proposed ABC and ABC-LS fuzzy modeling
strategies are evaluated on complex modeling problems and compared
to other advanced modeling methods.
Abstract: A single-phase closed thermosyphon has been
fabricated and experimented to utilize solar energy for water heating.
The working fluid of the closed thermosyphon is heated at the flatplate
collector and the hot water goes to the water tank due to density
gradient caused by temperature differences. This experimental work
was done using insulated water tank and insulated connecting pipe
between the tank and the flat-plate collector. From the collected data,
performance parameters such as instantaneous collector efficiency
and heat removal factor are calculated. In this study, the effects of
glazing were also observed. The water temperature rise and the
maximum instantaneous efficiency obtained from this experiment
with glazing using insulated water tank and insulated connecting pipe
are 17°C in a period of 5 hours and 60% respectively. Whereas the
water temperature rise and the maximum instantaneous efficiency
obtained from this experiment with glazing using non-insulated water
tank and non-insulated connecting pipe are 14°C in a period of 5
hours and 39% respectively.
Abstract: Supermarkets are the most electricity-intensive type of
commercial buildings. The unsuitable indoor environment of a
supermarket provided by abnormal HVAC operations incurs waste
energy consumption in refrigeration systems. This current study
briefly describes significantly solid backgrounds and proposes easyto-
use analysis terminology for investigating the impact of HVAC
operations on refrigeration power consumption using the field-test
data obtained from building automation system (BAS). With solid
backgrounds and prior knowledge, expected energy interactions
between HVAC and refrigeration systems are proposed through
Pearson’s correlation analysis (R value) by considering correlations
between equipment power consumption and dominantly independent
variables (driving force conditions).The R value can be conveniently
utilized to evaluate how strong relations between equipment
operations and driving force parameters are. The calculated R values
obtained from field data are compared to expected ranges of R values
computed by energy interaction methodology. The comparisons can
separate the operational conditions of equipment into faulty and
normal conditions. This analysis can simply investigate the condition
of equipment operations or building sensors because equipment could
be abnormal conditions due to routine operations or faulty
commissioning processes in field tests. With systematically solid and
easy-to-use backgrounds of interactions provided in the present
article, the procedures can be utilized as a tool to evaluate the proper
commissioning and routine operations of HVAC and refrigeration
systems to detect simple faults (e.g. sensors and driving force
environment of refrigeration systems and equipment set-point) and
optimize power consumption in supermarket buildings. Moreover,
the analysis will be used to further study the FDD research for
supermarkets in future.
Abstract: Cement-based grouts has been used successfully to
repair cracks in many concrete structures such as bridges, tunnels,
buildings and to consolidate soils or rock foundations. In the present
study the rheological characterization of cement grout with
water/binder ratio (W/B) is fixed at 0.5. The effect of the replacement
of cement by bentonite (2 to 10% wt) in presence of superplasticizer
(0.5% wt) was investigated. Several rheological tests were carried out
by using controlled-stress rheometer equipped with vane geometry in
temperature of 20°C. To highlight the influence of bentonite and
superplasticizer on the rheological behavior of grout cement, various
flow tests in a range of shear rate from 0 to 200 s-1 were observed.
Cement grout showed a non-Newtonian viscosity behavior at all
concentrations of bentonite. Three parameter model Herschel-
Bulkley was chosen for fitting of experimental data. Based on the
values of correlation coefficients of the estimated parameters, The
Herschel-Bulkley law model well described the rheological behavior
of the grouts. Test results showed that the dosage of bentonite
increases the viscosity and yield stress of the system and introduces
more thixotropy. While the addition of both bentonite and
superplasticizer with cement grout improve significantly the fluidity
and reduced the yield stress due to the action of dispersion of SP.
Abstract: Different services based on different switching
techniques in wireless networks leads to drastic changes in the
properties of network traffic. Because of these diversities in services,
network traffic is expected to undergo qualitative and quantitative
variations. Hence, assumption of traffic characteristics and the
prediction of network events become more complex for the wireless
networks. In this paper, the traffic characteristics have been studied
by collecting traces from the mobile switching centre (MSC). The
traces include initiation and termination time, originating node, home
station id, foreign station id. Traffic parameters namely, call interarrival
and holding times were estimated statistically. The results
show that call inter-arrival and distribution time in this wireless
network is heavy-tailed and follow gamma distributions. They are
asymptotically long-range dependent. It is also found that the call
holding times are best fitted with lognormal distribution. Based on
these observations, an analytical model for performance estimation is
also proposed.
Abstract: In the present study, we have synthesized Cr and Fe
doped zinc oxide (ZnO) nanostructures (Zn1-δCraFebO; where δ = a +
b = 20%, a = 5, 6, 8 & 10% and b = 15, 14, 12 & 10%) via sol-gel
method at different doping concentrations. The synthesized samples
were characterized for structural properties by X-ray diffractrometer
and field emission scanning electron microscope and the optical
properties were carried out through photoluminescence and UVvisible
spectroscopy. The particle size calculated through field
emission scanning electron microscope varies from 41 to 96 nm for
the samples synthesized at different doping concentrations. The
optical band gaps calculated through UV-visible spectroscopy are
found to be decreasing from 3.27 to 3.02 eV as the doping
concentration of Cr increases and Fe decreases.
Abstract: Multiwall carbon nanotubes, prepared by chemical
vapor deposition, have an average diameter of 60-100 nm as shown
by High Resolution Transmittance Electron Microscope, HR-TEM.
The Multiwall carbon nanotubes (MWCNTs) were further
characterized using X-ray Diffraction and Raman Spectroscopy.
Mercury uptake capacity of MWCNTs was studied using batch
adsorption method at different concentration ranges up to 150 ppm.
Mercury concentration (before and after the treatment) was measured
using cold vapor atomic absorption spectroscopy. The effect of time,
concentration, pH and adsorbent dose were studied. MWCNT were
found to perform complete absorption in the sub-ppm concentrations
(parts per billion levels) while for high concentrations, the adsorption
efficiency was 92% at the optimum conditions; 0.1 g of the adsorbent
at 150 ppm mercury (II) solution. The adsorption of mercury on
MWCNTs was found to follow the Freundlich adsorption isotherm
and the pseudo-second order kinetic model.
Abstract: Fuzzy systems have been successfully used for
exchange rate forecasting. However, fuzzy system is very confusing
and complex to be designed by an expert, as there is a large set of
parameters (fuzzy knowledge base) that must be selected, it is not a
simple task to select the appropriate fuzzy knowledge base for an
exchange rate forecasting. The researchers often look the effect of
fuzzy knowledge base on the performances of fuzzy system
forecasting. This paper proposes a genetic fuzzy predictor to forecast
the future value of daily US Dollar/Euro exchange rate time’s series.
A range of methodologies based on a set of fuzzy predictor’s which
allow the forecasting of the same time series, but with a different
fuzzy partition. Each fuzzy predictor is built from two stages, where
each stage is performed by a real genetic algorithm.
Abstract: The phased-array ultrasound transducer types are
utilities for medical ultrasonography as well as optical imaging.
However, their discontinuity characteristic limits the applications due
to the artifacts contaminated into the reconstructed images. Because
of the effects of the ultrasound pressure field pattern to the echo
ultrasonic waves as well as the optical modulated signal, the side
lobes of the focused ultrasound beam induced by discontinuity of the
phased-array ultrasound transducer might the reason of the artifacts.
In this paper, a simple method in approach of numerical simulation
was used to investigate the limitation of discontinuity of the elements
in phased-array ultrasound transducer and their effects to the
ultrasound pressure field. Take into account the change of ultrasound
pressure field patterns in the conditions of variation of the pitches
between elements of the phased-array ultrasound transducer, the
appropriated parameters for phased-array ultrasound transducer
design were asserted quantitatively.
Abstract: The global solved problem is the calculation of the
parameters of ceramic material from a set of destruction tests of
ceramic heads of total hip joint endoprosthesis. The standard way of
calculation of the material parameters consists in carrying out a set of
3 or 4 point bending tests of specimens cut out from parts of the
ceramic material to be analysed. In case of ceramic heads, it is not
possible to cut out specimens of required dimensions because the
heads are too small (if the cut out specimens were smaller than the
normalised ones, the material parameters derived from them would
exhibit higher strength values than those which the given ceramic
material really has). A special destruction device for heads
destruction was designed and the solved local problem is the
modification of this destructive device based on the analysis of
tensile stress in the head for two different values of the depth of the
conical hole in the head. The goal of device modification is a shift of
the location with extreme value of σ1max from the region of head’s
hole bottom to its opening. This modification will increase the
credibility of the obtained material properties of bioceramics, which
will be determined from a set of head destructions using the Weibull
weakest link theory.
Abstract: Stochastic User Equilibrium (SUE) model is a widely
used traffic assignment model in transportation planning, which is
regarded more advanced than Deterministic User Equilibrium (DUE)
model. However, a problem exists that the performance of the SUE
model depends on its error term parameter. The objective of this
paper is to propose a systematic method of determining the
appropriate error term parameter value for the SUE model. First, the
significance of the parameter is explored through a numerical
example. Second, the parameter calibration method is developed
based on the Logit-based route choice model. The calibration process
is realized through multiple nonlinear regression, using sequential
quadratic programming combined with least square method. Finally,
case analysis is conducted to demonstrate the application of the
calibration process and validate the better performance of the SUE
model calibrated by the proposed method compared to the SUE
models under other parameter values and the DUE model.
Abstract: 3D part library is an ideal approach to reuse the
existing design and thus facilitates the modeling process, which will
enhance the efficiency. In this paper, we implemented the thought on
the SolidWorks platform. The system supports the functions of type
and parameter selection, 3D template driving and part assembly.
Finally, BOM is exported in Excel format. Experiment shows that our
method can satisfy the requirement of die and mold designers.
Abstract: In this paper two approaches to joint signal detection,
time of arrival (ToA) and angle of arrival (AoA) estimation in
multi-element antenna array are investigated. Two scenarios were
considered: first one, when the waveform of the useful signal
is known a priori and, second one, when the waveform of the
desired signal is unknown. For first scenario, the antenna array
signal processing based on multi-element matched filtering (MF)
with the following non-coherent detection scheme and maximum
likelihood (ML) parameter estimation blocks is exploited. For second
scenario, the signal processing based on the antenna array elements
covariance matrix estimation with the following eigenvector analysis
and ML parameter estimation blocks is applied. The performance
characteristics of both signal processing schemes are thoroughly
investigated and compared for different useful signals and noise
parameters.
Abstract: The parameters of a two-layer soil can be determined by
processing resistivity data obtained from resistivity measurements
carried out on the soil of interest. The processing usually entails
applying the resistivity data as inputs to an optimisation function.
This paper proposes an algorithm which utilises the square error as an
optimisation function. Resistivity data from previous works were
applied to test the accuracy of the new algorithm developed and the
result obtained conforms significantly to results from previous works.
Abstract: A novel simulation method to determine the
displacements of machine tools due to thermal factors is presented.
The specific characteristic of this method is the employment of
original CAD data from the design process chain, which is
interpreted by an algorithm in terms of geometry-based allocation of
convection and radiation parameters. Furthermore analogous models
relating to the thermal behaviour of machine elements are
automatically implemented, which were gained by extensive
experimental testing with thermography imaging. With this a
transient simulation of the thermal field and in series of the
displacement of the machine tool is possible simultaneously during
the design phase. This method was implemented and is already used
industrially in the design of machining centres in order to improve
the quality of herewith manufactured workpieces.
Abstract: Identification and selection of appropriate product and
manufacturing technologies are key factors for competitiveness and
market success of technology-based companies. Therefore, many
companies perform technology intelligence (TI) activities to ensure
the identification of evolving technologies at the right time.
Technology monitoring is one of the three base activities of TI,
besides scanning and scouting.
As the technological progress is accelerating, more and more
technologies are being developed. Against the background of limited
resources it is therefore necessary to focus TI activities. In this paper
we propose a concept for defining appropriate search fields for
technology monitoring. This limitation of search space leads to more
concentrated monitoring activities. The concept will be introduced
and demonstrated through an anonymized case study conducted
within an industry project at the Fraunhofer Institute for Production
Technology IPT.
The described concept provides a customized monitoring
approach, which is suitable for use in technology-oriented companies.
It is shown in this paper that the definition of search fields and search
tasks are suitable methods to define topics of interest and thus to
align monitoring activities. Current as well as planned product,
production and material technologies and existing skills, capabilities
and resources form the basis for derivation of relevant search areas.
To further improve the concept of technology monitoring the
proposed concept should be extended during future research e.g. by
the definition of relevant monitoring parameters.
Abstract: The study was conducted to evaluate the efficiency of
Garlic and Chili combination solution on control of insect pests in
cabbage crop. The solution was sprayed at different intervals after
transplanting. The efficiency of Garlic and chili combination solution
on cabbage insect pests was measured. Results revealed that Garlic
and chili combination solution was the effectively reduced cabbage
insect pests. On other hand, the spray solution not only reduced the
number of days required for the cabbage growth but also greatly
enhanced the leaf number, head diameter, head weight, and quality of
cabbage. Garlic and chili combination solution have positive effects
on pests reduction and improve growth, yield and quality of cabbage
vegetable.
Abstract: Nonstandard tests are necessary for analyses and
verification of new developed structural and technological solutions
with application of composite materials. One of the most critical
primary structural parts of a typical aerospace structure is T-joint.
This structural element is loaded mainly in shear, bending, peel and
tension. The paper is focused on the shear loading simulations. The
aim of the work is to obtain a representative uniform distribution of
shear loads along T-joint during the mechanical testing. A new
design of T-joint test procedure, numerical simulation and
optimization of representative boundary conditions are presented.
The different conditions and inaccuracies both in simulations and
experiments are discussed. The influence of different parameters on
stress and strain distributions is demonstrated on T-joint made of
CFRP (carbon fibre reinforced plastic). A special test rig designed by
VZLU (Aerospace Research and Test Establishment) for T-shear test
procedure is presented.
Abstract: The theoretical approach is developed to describe the
change of drops in the atmosphere of own steam and buffer gas under
irradiation. It is shown that the irradiation influences on size of stable
droplet and on the conditions under which the droplet exists. Under
irradiation the change of drop becomes more complex: the not
monotone and periodical change of size of drop becomes possible.
All possible solutions are represented by means of phase portrait. It is
found all qualitatively different phase portraits as function of critical
parameters: rate generation of clusters and substance density.
Abstract: Characterization of the engineering behavior of
unsaturated soil is dependent on the soil-water characteristic curve
(SWCC), a graphical representation of the relationship between water
content or degree of saturation and soil suction. A reasonable
description of the SWCC is thus important for the accurate prediction
of unsaturated soil parameters. The measurement procedures for
determining the SWCC, however, are difficult, expensive, and timeconsuming.
During the past few decades, researchers have laid a
major focus on developing empirical equations for predicting the
SWCC, with a large number of empirical models suggested. One of
the most crucial questions is how precisely existing equations can
represent the SWCC. As different models have different ranges of
capability, it is essential to evaluate the precision of the SWCC
models used for each particular soil type for better SWCC estimation.
It is expected that better estimation of SWCC would be achieved via
a thorough statistical analysis of its distribution within a particular
soil class. With this in view, a statistical analysis was conducted in
order to evaluate the reliability of the SWCC prediction models
against laboratory measurement. Optimization techniques were used
to obtain the best-fit of the model parameters in four forms of SWCC
equation, using laboratory data for relatively coarse-textured (i.e.,
sandy) soil. The four most prominent SWCCs were evaluated and
computed for each sample. The result shows that the Brooks and
Corey model is the most consistent in describing the SWCC for sand
soil type. The Brooks and Corey model prediction also exhibit
compatibility with samples ranging from low to high soil water
content in which subjected to the samples that evaluated in this study.