Abstract: Agricultural machinery industry plays an important
role in the industrial development especially the production industry
of the country. There has been continuing development responding to
the higher demand of the production. However, the problem in
agricultural machinery production still exists. Thus, the purpose of
this research is to investigate problems on fundamental factors of
industry based on the entrepreneurs’ point of view. The focus was on
the small and medium size industry receiving factory license type
number 0660 from the Department of Industrial Works. The
investigation was on the comparison between the management of the
small and medium size agricultural industry in 3 provinces in the
central region of Thailand. Population in this study consisted of 189
company managers or managing directors, of which 101 were from
the small size and 88 were from the medium size industry. The data
were analyzed to find percentage, arithmetic mean, and standard
deviation with independent sample T-test at the statistical
significance .05. The results showed that the small and medium size
agricultural machinery manufacturers in the central region of
Thailand reported high problems in every aspect. When compared the
problems on basic factors in running the business, it was found that
there was no statistically difference at .05 in managing of the small
and medium size agricultural machinery manufacturers. However,
there was a statistically significant difference between the small and
medium size agricultural machinery manufacturers on the aspect of
policy and services of the government. The problems reported by the
small and medium size agricultural machinery manufacturers were
the services on public tap water and the problem on politic and
stability of the country.
Abstract: Job satisfaction and motivation have been given an
important attention in psychology because they are seen as main
instruments in maintaining organizational growth and development;
they are also used to accomplish organizational aims and objectives.
However, it has been observed that some institutions failed in
motivating and stimulating their workers; in contrast, workers may be
motivated but not satisfied with the job and failed to perform
efficiently and effectively. It is hoped that the study of this nature
would be of significance value to all stakeholders in education
specifically, lecturers in higher institutions in Nigeria. Also, it is
hoped that the findings of this study will enhance lecturers’
effectiveness and performance in discharging their duties. In the light
of the above statements, this study investigated whether job
satisfaction and motivation predict lecturers’ effectiveness in Nigeria
Police Academy, Wudil, Kano State. Correlational research method
was adopted for the study, while purposive sampling technique was
used to choose the institution and the sampled lectures (70). Simple
random sampling technique was used to select one hundred cadets
across the academy. Two instruments were used to elicit information
from both lecturers and cadets. These were job satisfaction and
motivation; and lecturers’ effectiveness Questionnaires. The
instruments were subjected to pilot testing and found to have
reliability coefficient of 0.69 and 0.71 respectively. The results of the
study revealed that there was a significance relationship among job
satisfaction, motivation and lecturers effectiveness in Nigeria Police
Academy. There was a significance relationship between job
satisfaction and lecturers’ effectiveness in Nigeria Police Academy
the cal r is 0.21 while the crt r is 0.19. at p
Abstract: Over the past few decades, manufacturing has evolved
from a more labor-intensive set of mechanical processes to a
sophisticated set of information based technology processes. With the
existence of various advanced manufacturing technologies (AMTs),
more and more functions or jobs are performed by these machines
instead of human labour. This study was undertaken in order to
research the extent of AMTs adoption in manufacturing companies in
Kenya. In order to investigate a survey was conducted via
questionnaires that were sent to 183 selected AMT manufacturing
companies in Kenya. 92 companies responded positively. All the
surveyed companies were found to have a measure of investment in
at least two of the 14 types of AMTs investigated. In general the
company surveyed showed that the level of AMT adoption in Kenya
is very low with investments levels at a mean of 2.057 and
integration levels at a mean of 1.639 in a scale of 1-5.
Abstract: Present empirical paper investigates the relationship
between FDI and economic growth by 10 selected industries in 10
Central and Eastern European countries from the period 1995 to
2012. Different estimation approaches were used to explore the
connection between FDI and economic growth, for example OLS,
RE, FE with and without time dummies. Obtained empirical results
leads to some main consequences: First, the Central and East
European countries (CEEC) attracted foreign direct investment,
which raised the productivity of industries they entered in. It should
be concluded that the linkage between FDI and output growth by
industries is positive and significant enough to suggest that foreign
firm’s participation enhanced the productivity of the industries they
occupied. There had been an endogeneity problem in the regression
and fixed effects estimation approach was used which partially
corrected the regression analysis in order to make the results less
biased. Second, it should be stressed that the results show that time
has an important role in making FDI operational for enhancing output
growth by industries via total factor productivity. Third, R&D
positively affected economic growth and at the same time, it should
take some time for research and development to influence economic
growth. Fourth, the general trends masked crucial differences at the
country level: over the last 20 years, the analysis of the tables and
figures at the country level show that the main recipients of FDI of
the 11 Central and Eastern European countries were Hungary, Poland
and the Czech Republic. The main reason was that these countries
had more open door policies for attracting the FDI. Fifth, according
to the graphical analysis, while Hungary had the highest FDI inflow
in this region, it was not reflected in the GDP growth as much as in
other Central and Eastern European countries.
Abstract: A three-dimensional numerical simulation of flow
through mini and microchannels with designed roughness is
conducted here. The effect of the roughness height (surface
roughness), geometry, Reynolds number on the friction factor, and
Nusselt number is investigated. The study is carried out by
employing CFD software, CFX. Our work focuses on a water flow
inside a circular mini-channel of 1 mm and microchannels of 500 and
100 m in diameter. The speed entry varies from 0.1 m/s to 20 m/s.
The general trend can be observed that bigger sizes of roughness
element lead to higher flow resistance. It is found that the friction
factor increases in a nonlinear fashion with the increase in obstruction
height. Particularly, the effect of roughness can no longer be ignored
at relative roughness height higher than 3%. A significant increase in
Poiseuille number is detected for all configurations considered. The
same observation can be done for Nusselt number. The transition
zone between laminar and turbulent flow depends on the channel
diameter.
Abstract: We present probabilistic multinomial Dirichlet
classification model for multidimensional data and Gaussian process
priors. Here, we have considered efficient computational method that
can be used to obtain the approximate posteriors for latent variables
and parameters needed to define the multiclass Gaussian process
classification model. We first investigated the process of inducing a
posterior distribution for various parameters and latent function by
using the variational Bayesian approximations and important sampling
method, and next we derived a predictive distribution of latent
function needed to classify new samples. The proposed model is
applied to classify the synthetic multivariate dataset in order to verify
the performance of our model. Experiment result shows that our model
is more accurate than the other approximation methods.
Abstract: The purpose of the study is to investigate the level of
intrinsic motivation of trainers after attending a Continuous
Professional Development Course (CPD) organized by Institute of
Teacher Training Malaysia titled, “Transformation of Teaching and
Learning the Fun Way”. This study employed a survey whereby 96
teacher trainers were given Situational Intrinsic Motivational Scale
(SIMS) Instruments. Confirmatory factor analysis was carried out to
get the validity of this instrument in local setting. Data were analyzed
with SPSS for descriptive statistic. Semi- structured interviews were
also administrated to collect qualitative data on participants’
experiences after participating in the two-day fun-filled program. The
findings showed that the participants’ level of intrinsic motivation
showed higher mean than the amotivation. The results revealed that
the intrinsic motivation mean is 19.0 followed by Identified
regulation with a mean of 17.4, external regulation 9.7 and
amotivation 6.9. The interview data also revealed that the participants
were motivated after attending this training program. It can be
concluded that this program, which was organized by Institute of
Teacher Training Malaysia, was able to enhance participants’ level of
motivation. Self-Determination Theory (SDT) as a multidimensional
approach to motivation was utilized. Therefore, teacher trainers may
have more success using the “The fun way approach” in conducting
training program in future.
Abstract: The aim of the study was to investigate the effect of
Saccharomyces cerevisiae (SC) live yeast culture on microbial
protein supply to small intestine in Kivircik male yearlings when fed
with different ratio of forage and concentrate diets. Four Kivircik
male yearlings with permanent rumen canula were used in the
experiment. The treatments were allocated to a 4x4 Latin square
design. Diet I consisted of 70% alfalfa hay and 30% concentrate, Diet
II consisted of 30% alfalfa hay and 70% concentrate, Diet I and II
were supplemented with a SC. Daily urine was collected and stored at
-20°C until analysis. Calorimetric methods were used for the
determination of urinary allantoin and creatinine levels. The
estimated microbial N supply to small intestine for Diets I, I+SC, II
and II+SC were 2.51, 2.64, 2.95 and 3.43 g N/d respectively.
Supplementation of Diets I and II with SC significantly affected the
allantoin levels in μmol/W0.75 (p
Abstract: Durian skin is a newly explores natural fibre
potentially reinforced polyolefin for diverse applications. In this
work, investigation on the effect of coupling agent, maleic anhydride
polypropylene (MAPP) on the mechanical, morphological, and
thermal properties of polypropylene (PP) reinforced with durian skin
fibre (DSF) was conducted. The presence of 30 wt% DSF
significantly reduced the tensile strength of PP-DSF composite.
Interestingly, even though the same trend goes to PP-DSF with the
presence of MAPP, the reduction is only about 4% relative to
unreinforced PP and 18% higher than PP-DSF without MAPP
(untreated composite or UTC). The used of MAPP in treated
composite (TC) also increased the tensile modulus, flexural
properties and degradation temperature. The enhanced mechanical
properties are consistent with good interfacial interaction as
evidenced under scanning electron microscopy.
Abstract: Production fluids are transported from the platform to
tankers or process facilities through transfer pipelines. Water being
one of the heavier phases tends to settle at the bottom of pipelines
especially at low flow velocities and this has adverse consequences
for pipeline integrity. On restart after a shutdown, this could result in
corrosion and issues for process equipment, thus the need to have the
heavier liquid dispersed into the flowing lighter fluid. This study
looked at the flow regime of low water cut and low flow velocity oil
and water flow using conductive film thickness probes in a large
diameter 4-inch pipe to obtain oil and water interface height and the
interface structural velocity. A wide range of 0.1–1.0 m/s oil and
water mixture velocities was investigated for 0.5–5% water cut. Two
fluid model predictions were used to compare with the experimental
results.
Abstract: This research aimed to investigate the relationship
between attitude towards marketing mix, brand image and consumer
behavior of the passengers of low-cost airlines service. This study
employed by quantitative research and the questionnaire was used to
collect the data from 400 sampled of the passengers who have ever
used the low-cost airline services based in Bangkok, Thailand. The
descriptive statistics and Pearson’s correlation analysis were used to
analyze data. The research results revealed that the attitude of the marketing mix
of the low-cost airline services including product, price, place,
promotion and process had related to the consumer behavior on the
aspects of duration of service and frequency of service. While, the
brand image of the low cost airline including the characteristics of
organization, service quality and company identity had related to the
consumer behavior on duration of service, frequency of service and
cost of service at the significant statistically acceptable levels.
Abstract: A number of studies have been conducted recently to
investigate the influence of randomly oriented fibers on some
engineering properties of cohesive and cohesionless soils. However,
few studies have been carried out on freezing-thawing behavior of
fine-grained soils modified with discrete fiber inclusions and additive
materials. This experimental study was performed to investigate the
effect of randomly distributed polypropylene fibers (PP) and some
additive materials [e.g.., borogypsum (BG), fly ash (FA) and cement
(C)] on freezing-thawing durability (mass losses) of a fine-grained
soil for 6, 12, and 18 cycles. The Taguchi method was applied to the
experiments and a standard L9 orthogonal array (OA) with four
factors and three levels were chosen. A series of freezing-thawing
tests were conducted on each specimen. 0-20% BG, 0-20% FA, 0-
0.25% PP and 0-3% of C by total dry weight of mixture were used in
the preparation of specimens. Experimental results showed that the
most effective materials for the freezing-thawing durability (mass
losses) of the samples were borogypsum and fly ash. The values of
mass losses for 6, 12 and 18 cycles in optimum conditions were
16.1%, 5.1% and 3.6%, respectively.
Abstract: In this study, the time-dependent behavior of damaged
reinforced concrete shear wall structures strengthened with composite
plates having variable fibers spacing was investigated to analyze their
seismic response. In the analytical formulation, the adherent and the
adhesive layers are all modeled as shear walls, using the mixed Finite
Element Method (FEM). The anisotropic damage model is adopted to
describe the damage extent of the Reinforced Concrete shear walls.
The phenomenon of creep and shrinkage of concrete has been
determined by Eurocode 2. Large earthquakes recorded in Algeria
(El-Asnam and Boumerdes) have been tested to demonstrate the
accuracy of the proposed method. Numerical results are obtained for non-uniform distributions of
carbon fibers in epoxy matrices. The effects of damage extent and the
delay mechanism creep and shrinkage of concrete are highlighted.
Prospects are being studied.
Abstract: Gastric Cancer (GC) has high morbidity and fatality
rate in various countries. It is still one of the most frequent and
deadly diseases. Gastrokine1 (GKN1) and gastrokine2 (GKN2) genes
are highly expressed in the normal stomach epithelium and play
important roles in maintaining the integrity and homeostasis of
stomach mucosal epithelial cells. In this study, 47 paired samples that
were grouped according to the types of gastric cancer and the clinical
characteristics of the patients, including gender and average of age.
They were investigated with gene expression analysis and mutation
screening by monitoring RT-PCR, SSCP and nucleotide sequencing
techniques. Both GKN1 and GKN2 genes were observed significantly
reduced found by (Wilcoxon signed rank test; p
Abstract: The understanding of geotechnical characteristics of
near-surface material and the effects of the groundwater is very
important problem in such as site studies. For showing the relations
between seismic data and groundwater, we selected about 25 km2 as
the study area. It has been presented which is a detailed work of
seismic data and groundwater depths of Gokpinar Damp area.
Seismic waves velocity (Vp and Vs) are very important parameters
showing the soil properties. The seismic records were used the
method of the multichannel analysis of surface waves near area of
Gokpinar Damp area. Sixty sites in this area have been investigated
with survey lines about 60 m in length. MASW (Multichannel
analysis of surface wave) method has been used to generate onedimensional
shear wave velocity profile at locations. These shear
wave velocities are used to estimate equivalent shear wave velocity in
the study area at every 2 and 5 m intervals up to a depth of 45 m.
Levels of equivalent shear wave velocity of soil are used the
classified of the study area. After the results of the study, it must be
considered as components of urban planning and building design of
Gokpinar Damp area, Denizli and the application and use of these
results should be required and enforced by municipal authorities.
Abstract: Strong anthropogenic impact has uncontrolled
consequences on the nature of the soil. Hence, up-to-date sustainable
methods of soil state improvement are essential. Investigators provide
the evidence that biochar can positively effects physical, chemical,
and biological soil properties and the abundance of mycorrhizal fungi
which are in the focus of this study. The main aim of the present
investigation is to demonstrate the effect of two types of plant growth
promoting bacteria (PGPB) inoculums along with the beech wood
biochar and mineral N additives on mycorrhizal colonization.
Experiment has been set up in laboratory conditions with containers
filled with arable soil from the protection zone of the main water
source “Brezova nad Svitavou”. Lactuca sativa (lettuce) has been
selected as a model plant. Based on the obtained data, it can be
concluded that mycorrhizal colonization increased as the result of
combined influence of biochar and PGPB inoculums amendment. In
addition, correlation analyses showed that the numbers of main
groups of cultivated bacteria were dependent on the degree of
mycorrhizal colonization.
Abstract: This study aims to investigate the relationships
between human resource management and entrepreneurship in the
view of owner-managers and employees, and among employees with
in the SME in Thailand. The research method used qualitative
method to confirm the phenomenology interest with top management
position which women are regarding their career path by using
purposive sampling method. The results showed that human
resources management has positive relate with the corporate
entrepreneurship are including the recruitment process, training
worker, professional career development and reward system impact
to entrepreneur’s knowledge and innovation of corporate
entrepreneurship in respectively to bring a very reliable way. Then,
the key informant suggested that women’s career experiences
predisposed them to find an alternative route for entrepreneurship,
despite having achieved top management. The understanding factors
that successfully contribute to the development of women
entrepreneurs from career development perspective are critical
endeavour for any type of organization as well.
Abstract: This study investigates the influence of low
temperature thermo-chemical pretreatment of organic food waste on
performance of COD solubilisation. Both temperature and alkaline
agent were reported to have effect on solubilizing any possible
biomass including organic food waste. The three independent
variables considered in this pretreatment were temperature (50-90oC),
pretreatment time (30-120 minutes) and alkaline concentration,
sodium hydroxide, NaOH (0.7-15 g/L). The maximal condition
obtained were 90oC, 15 g/L NaOH for 2 hours. Solubilisation has
potential in enhancing methane production by providing high amount
of soluble components at early stage during anaerobic digestion.
Abstract: In this paper, the 2-D unsteady viscous flow around
two cam shaped cylinders in tandem arrangement is numerically
simulated in order to study the characteristics of the flow in turbulent
regimes. The investigation covers the effects of high subcritical and
supercritical Reynolds numbers and L/D ratio on total drag
coefficient. The equivalent diameter of cylinders is 27.6 mm The
space between center to center of two cam shaped cylinders is define
as longitudinal pitch ratio and it varies in range of 1.5< L/D
Abstract: The 1:1 cocrystal of 2-amino-4-chloro-6-
methylpyrimidine (2A4C6MP) with 4-methylbenzoic acid (4MBA)
(I) has been prepared by slow evaporation method in methanol,
which was crystallized in monoclinic C2/c space group, Z = 8, and a
= 28.431 (2) Å, b = 7.3098 (5) Å, c = 14.2622 (10) Å and β =
109.618 (3)°. The presence of unionized –COOH functional group in
cocrystal I was identified both by spectral methods (1H and 13C
NMR, FTIR) and X-ray diffraction structural analysis. The
2A4C6MP molecule interact with the carboxylic group of the
respective 4MBA molecule through N—H⋯O and O—H⋯N
hydrogen bonds, forming a cyclic hydrogen–bonded motif R2
2(8).
The crystal structure was stabilized by Npyrimidine—H⋯O=C and
C=O—H⋯Npyrimidine types hydrogen bonding interactions.
Theoretical investigations have been computed by HF and density
function (B3LYP) method with 6–311+G (d,p)basis set. The
vibrational frequencies together with 1H and 13C NMR chemical
shifts have been calculated on the fully optimized geometry of
cocrystal I. Theoretical calculations are in good agreement with the
experimental results. Solvent–free formation of this cocrystal I is
confirmed by powder X-ray diffraction analysis.